Move the code to enter Auto Select Mode down to be able to use cfi->cfiq
members to add support for chips using alternative sequence / unlock
addresses.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a kirkwood_nand_init_rnb() call to allow boards which
have RnB line detection to register this instead of a
static delay.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2GB xD card, and 4MB SmartMedia ROM card share same ID, so to make both work
split xD and smartmedia ID tables.
Hardware driver must be able to know which type it handles (and probably just one).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set,
NFC_CONFIG2:NFC_INT always reads out zero, even if an
operation is completed. This patch uses enable_irq and
disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to
mask NFC interrupts. This allows NFC_CONFIG2:NFC_INT to also
be used to detect operation completion on i.MX21.
The i.MX21 NFC does not signal reset completion using
NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is
tested by checking if NFC_CONFIG2 becomes 0.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows the mxc_nand driver to reset the NAND
flash controller. NFC registers are (re-)set after
completion of the reset, as a reset will have reverted
the NFC registers to their default values.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is to support custom partitioning schemes for embedded PPC. To use
define your own mtd_part_parser and then add something like:
linux,part-probe = "my_probe", "cmdlinepart";
To the board's dts file.
If linux,part-probe is not specified then this behaves the same as before.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/denali.c:1427: error: conflicting types for ‘enable_dma’
arch/powerpc/include/asm/dma.h:189: note: previous definition of ‘enable_dma’ was here
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is more work to be done on this but it is basically working now.
Signed-off-by: Jason Roberts <jason.e.roberts@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a build failure[1] by simply moving the function mtd_to_flctl
beneath the definition of sh_flctl which it uses.
BF introduced by patch
'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418)
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The revision in SVR for MPC5123 is 3. The NFC is the same as MPC5121
revision 2.
Signed-off-by: Steve Deiters <SteveDeiters@basler.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All the SST25L series flash parts have uniform erase sectors. Remove
the extra MTD_DEBUG_LEVEL2 messages showing the eraseregions info
since they could never be shown.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ensure that the flash device is in a quiescent state before rebooting.
The implementation is closely modeled after the cfi_cmdset_0001 reboot
notifier, commit 963a6fb0a0 .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The pxa32xx_nand driver doesn't support partition tables from the
command line. This patch adds support for it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Moved the debugging message before the call to map_destroy, which frees its
argument. The message is also slightly changed to reflect its new
position.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
del_mtd_device(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The use of a memcpy() during a spinlock operation will cause very long
thread context switch delays if the flash chip bandwidth is low and the
data to be copied large, because a spinlock will disable preemption.
For example: A flash with 6,5 MB/s bandwidth will cause under ubifs,
which request sometimes 128 KiB (the flash erase size), a preemption delay of
20 milliseconds. High priority threads will not be served during this
time, regardless whether this threads access the flash or not. This behavior
breaks real time.
The patch changes all the use of spin_lock operations for xxxx->mutex
into mutex operations, which is exact what the name says and means.
I have checked the code of the drivers and there is no use of atomic
pathes like interrupt or timers. The mtdoops facility will also not be used
by this drivers. So it is dave to replace the spin_lock against mutex.
There is no performance regression since the mutex is normally not
acquired.
Changelog:
06.03.2010 First release
26.03.2010 Fix mutex[1] issue and tested it for compile failure
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Functions omap2_onenand_write_bufferram() and omap3_onenand_write_bufferram()
map the write buffer and store the returned handle in variable dma_src. However,
when DMA unmap is done, variable dma_dst is used instead of the correct dma_src.
This patch fixes them to use the correct DMA buffer.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all magic numbers into appropriate defines, and move the defines
out of the global namespace and into this one driver. No other driver
needs to care about the MMR layout anyways.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need these names. Moreover, there are spelling typos
there: "nansin" instead of "nandsim".
This patch is just a clean up, no functional changes.
Reported-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
commit 672917dcc7 ("cpuidle: menu governor: reduce latency on exit")
added an optimization, where the analysis on the past idle period moved
from the end of idle, to the beginning of the new idle.
Unfortunately, this optimization had a bug where it zeroed one key
variable for new use, that is needed for the analysis. The fix is
simple, zero the variable after doing the work from the previous idle.
During the audit of the code that found this issue, another issue was
also found; the ->measured_us data structure member is never set, a
local variable is always used instead.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md:
md: restore ability of spare drives to spin down.
md/raid6: Fix raid-6 read-error correction in degraded state
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: fix compilation after 16bit state locking changes
pcmcia: order userspace suspend and resume requests
pcmcia: avoid pccard_validate_cis failure in resume callpath
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
blk-cgroup: Fix an RCU warning in blkiocg_create()
blk-cgroup: Fix RCU correctness warning in cfq_init_queue()
drbd: don't expose failed local READ to upper layers
Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix RCU issues in the NFSv4 delegation code
NFSv4: Fix the locking in nfs_inode_reclaim_delegation()
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: sleep: init_set_sci_en_on_resume for Dell Studio 155x
ACPI: fix acpi_hest_firmware_first_pci() caused oops
sbshc: acpi_device_class "smbus_host_controller" too long
power_meter: acpi_device_class "power_meter_resource" too long
acpi_pad: "processor_aggregator" name too long
PNP: don't check for conflicts with bridge windows
ACPI: DMI init_set_sci_en_on_resume for multiple Lenovo ThinkPads
PNPACPI: compute Address Space length rather than using _LEN
ACPI: silence kmemcheck false positive
* 'v4l_for_2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB: pxa_camera: move fifo reset direct before dma start
V4L/DVB: video: testing unsigned for less than 0
V4L/DVB: mx1-camera: compile fix
V4L/DVB: budget: Oops: "BUG: unable to handle kernel NULL pointer dereference"
V4L/DVB: ngene: Workaround for stuck DiSEqC pin
V4L/DVB: saa7146: fix regression of the av7110/budget-av driver
V4L/DVB: v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
V4L/DVB: feature-removal: announce videotext.h removal
V4L/DVB: V4L - vpfe capture - fix for kernel crash
V4L/DVB: gspca: make usb id 0461:0815 get handled by the right driver
V4L/DVB: gspca - stv06xx: Remove the 046d:08da from the stv06xx driver
V4L/DVB: gspca - sn9c20x: Correct onstack wait_queue_head declaration
V4L/DVB: saa7146: fix up bytesperline if it is an impossible value
V4L/DVB: V4L: vpfe_capture - free ccdc_lock when memory allocation fails
V4L/DVB: V4L - Makfile:Removed duplicate entry of davinci
V4L/DVB: omap24xxcam: potential buffer overflow
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: create rcu_my_thread_group_empty() wrapper
memcg: css_id() must be called under rcu_read_lock()
cgroup: Check task_lock in task_subsys_state()
sched: Fix an RCU warning in print_task()
cgroup: Fix an RCU warning in alloc_css_id()
cgroup: Fix an RCU warning in cgroup_path()
KEYS: Fix an RCU warning in the reading of user keys
KEYS: Fix an RCU warning
Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down. Device failure/removal
etc are still recorded on spares.
However commit 51d5668cb2 broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:
This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain,
how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.
So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately. There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update). We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
with CONFIG_PROVE_RCU=y, a warning can be triggered:
# mount -t cgroup -o blkio xxx /mnt
# mkdir /mnt/subgroup
...
kernel/cgroup.c:4442 invoked rcu_dereference_check() without protection!
...
To fix this, we avoid caling css_depth() here, which is a bit simpler
than the original code.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's unused and buggy in its current form, since it can place a bo
in the reserved state without removing it from lru lists.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bring radeon up to speed with the async event synchronization for
drmWaitVblank. See c9a9c5e02a for
more information. Without this patch event never get delivered
to userspace client.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move the fifo reset from pxa_camera_start_capture to pxa_camera_irq direct
before the dma start after an end of frame interrupt to prevent images from
shifting because of old data at the begin of the frame.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_mbus_bytes_per_line() returns -EINVAL on error but we store it in an
unsigned int so the test for less than zero doesn't work. I think it
always returns "small" positive values so we can just cast it to int
here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a regression of
7d58289 (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Never call dvb_frontend_detach if we failed to attach a frontend. This fixes
the following oops, which will be triggered by a missing stv090x module:
[ 8.172997] DVB: registering new adapter (TT-Budget S2-1600 PCI)
[ 8.209018] adapter has MAC addr = 00:d0:5c:cc:a7:29
[ 8.328665] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8.328753] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 8.562047] DVB: Unable to find symbol stv090x_attach()
[ 8.562117] BUG: unable to handle kernel NULL pointer dereference at 000000ac
[ 8.562239] IP: [<e08b04a3>] dvb_frontend_detach+0x4/0x67 [dvb_core]
Ref http://bugs.debian.org/575207
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
