These are documented in the AQR115 register reference. I haven't tested
them, but perhaps they'll be useful to someone.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.
The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.
Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This documents the possible MLO_PAUSE_* settings which can result from
different combinations of MAC_(A)SYM_PAUSE. Special note is paid to
settings which can result from user configuration (MLO_PAUSE_AN). The
autonegotiation results are more-or-less a direct consequence of IEEE
802.3 Table 28B-2.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arınç ÜNAL says:
====================
dt-bindings and mt7621 devicetree changes
This patch series removes old MediaTek bindings, improves mediatek,mt7530
and mt7621 memory controller bindings and improves mt7621 DTs.
v4:
- Keep memory-controller node name.
- Change syscon to memory-controller on mt7621.dtsi.
v3:
- Explain the mt7621 memory controller binding change in more details.
- Remove explaining the remaining DTC warnings from the patch log as there
are new schemas submitted for them.
v2:
- Change memory controller node name to syscon on the schema example.
- Keep cpu compatible string and syscon on the memory controller node.
- Add Rob and Sergio's tags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing LEDs for GB-PC2. The ethblack-green, ethblue-green, power
and system LEDs weren't added previously, because they don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
The i2c bus cannot be used on GB-PC2 as its pins are wired to LEDs instead,
and GB-PC1 does not use it. Therefore, do not enable it on both devices.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the external phy on the mdio bus is 5. Update the devicetree
for GB-PC2 accordingly.
Fixes: 5bc148649c ("staging: mt7621-dts: fix GB-PC2 devicetree")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt-parent property is inherited from the ethernet node as it's a
parent node of the switch node. Therefore, remove the unnecessary
interrupt-parent property from the switch node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dtc warnings below.
uartlite@c00: $nodename:0: 'uartlite@c00' does not match '^serial(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
uartlite@c00: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
sdhci@1e130000: $nodename:0: 'sdhci@1e130000' does not match '^mmc(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
xhci@1e1c0000: $nodename:0: 'xhci@1e1c0000' does not match '^usb(@.*)?'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
xhci@1e1c0000: compatible: ['mediatek,mt8173-xhci'] is too short
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
switch0@0: $nodename:0: 'switch0@0' does not match '^(ethernet-)?switch(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
port@1: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@2: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@3: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
- Change "memc: syscon@5000" to "memc: memory-controller@5000".
- Change "uartlite: uartlite@c00" to "serial0: serial@c00" and remove the
aliases node.
- Remove "clock-names" from the serial0 node. The property doesn't exist on
the 8250.yaml schema.
- Change "sdhci: sdhci@1e130000" to "mmc: mmc@1e130000".
- Change "xhci: xhci@1e1c0000" to "usb: usb@1e1c0000".
- Add "mediatek,mtk-xhci" as the second compatible string on the usb node.
- Change "switch0: switch0@0" to "switch0: switch@0"
- Change "off" to "disabled" for disabled nodes.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syscon string was introduced because the mt7621 clock driver needs to
read some registers creating a regmap from the syscon. The bindings were
added before the clock driver was properly mainlined and at first the clock
driver was using ralink architecture dependent operations rt_memc_* defined
in 'arch/mips/include/asm/mach-ralink/ralink_regs.h'.
This string is already there on the memory controller node on mt7621.dtsi.
Add syscon as a constant string on the compatible property, now that memc
became a syscon. Update the example accordingly.
Fixes: 5278e4a181 ("dt-bindings: memory: add binding for Mediatek's MT7621 SDRAM memory controller")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the description of the gpio-controller property to include the
controllable pins of the MT7530 switch.
The gpio-controller property is only used for the MT7530 switch. Therefore,
invalidate it for the MT7531 switch.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove these old mediatek bindings which are not used.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Machon says:
====================
net: Add QoS offload support for sparx5
This patch series adds support for offloading QoS features with the tc
command suite, to the sparx5 switch. The new offloadable QoS features
introduced in this patch series are:
- tc-mqprio for mapping traffic class to hardware queue. Queues are by
default mapped 1:1 in hardware, as such the mqprio qdisc is used as
an attachment point for qdiscs tbf and ets.
$ tc qdisc add dev eth0 root handle 1:0 mqprio
- tc-tbf for setting up shaping on scheduler elements of the HSCH
(Hierarchical Scheduler) block. Shaping on either port output or
queue output is supported.
Port shaper: $ tc qdisc add dev eth0 root handle 1:0 tbf rate \
10000000 burst 8192 limit 1m
Queue shaper: $ tc qdisc replace dev eth0 parent 1:5 handle 2:0 tbf \
rate 10000000 burst 8192 limit 1m
- tc-ets for setting up strict and or bandwidth-sharing bands on one
through eight priority queues.
Configure a mix of strict and bw-sharing bands:
$ tc qdisc add dev eth0 handle 1: root ets bands 8 strict 5 \
quanta 1000 1000 1000 priomap 7 6 5 4 3 2 1 0
Patch #1 Sets up the tc hook.
Patch #2 Adds support for offloading the tc-mqprio qdisc.
Patch #3 Adds support for offloading the tc-tbf qdisc.
Patch #4 Adds support for offloading the tc-ets qdisc.
Patch #5 Updates the maintainers of the sparx5 driver.
========================================================================
v1:
https://lore.kernel.org/netdev/20220919120215.3815696-1-daniel.machon@microchip.com/
v1 -> v2:
- Fix compiler warning in patch #2
- Fix comment style in patch #4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update Maintainers file.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading ets qdisc to sparx5 switch.
The ets qdisc makes it possible to configure a mix og strict and
bandwidth-sharing bands. The ets qdisc must be attached as a root qdisc.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading tbf qdisc to sparx5 qdisc.
The tbf qdisc makes it possible to attach a shaper on traffic egressing
from a port or a queue. Per-port tbf qdiscs are attached as a root qdisc
directly and queue tbf qdiscs are attached to one of the classes of a
parent qdisc (such as mqprio).
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading mqprio qdisc to sparx5 switch.
The offloaded mqprio qdisc currently does nothing by itself, but serves
as an attachment point for other qdiscs (tbf, ets etc.)
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tc setup hook for QoS features.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary spi_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary dev_set_drvdata() in ->remove(), the driver_data will
be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary platform_set_drvdata() in ->remove(), the driver_data
will be set to NULL in device_unbind_cleanup() after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unnecessary set_drvdata(NULL) function in ->remove(),
the driver_data will be set to NULL in device_unbind_cleanup()
after calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have already a helper to get the first child device, use it and
drop custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vadfed@fb.com>
Link: https://lore.kernel.org/r/20220921141005.2443-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Check the return value of nla_nest_start(). When starting the entry
level nested attributes, if the tailroom of socket buffer is
insufficient to store the attribute header and payload, the return value
will be NULL.
There is, however, no real bug here since if the skb is full
nla_put_be16() will fail as well and we'll error out.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Link: https://lore.kernel.org/r/20220921181716.1629541-1-floridsleeves@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5 MACSec Extended packet number and replay window offload
This is a follow up series to the previously submitted mlx5 MACsec offload [1]
earlier this release cycle.
In this series we add the support for MACsec Extended packet number and
replay window offloads.
First patch is a simple modification (code movements) to the core macsec code
to allow exposing the EPN related user properties to the offloading
device driver.
The rest of the patches are mlx5 specific, we start off with fixing some
trivial issues with mlx5 MACsec code, and a simple refactoring to allow
additional functionality in mlx5 macsec to support EPN and window replay
offloads.
A) Expose mkey creation functionality to MACsec
B) Expose ASO object to MACsec, to allow advanced steering operations,
ASO objects are used to modify MACsec steering objects in fastpath.
1) Support MACsec offload extended packet number (EPN)
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
2) Support MACsec offload replay window
Support setting replay window size for MACsec offload.
Currently supported window size of 32, 64, 128 and 256
bit. Other values will be returned as invalid parameter.
[1] https://lore.kernel.org/netdev/20220906052129.104507-1-saeed@kernel.org/
====================
Link: https://lore.kernel.org/r/20220921181054.40249-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support setting replay window size for MACsec offload.
Currently supported window size of 32, 64, 128 and 256
bit. Other values will be returned as invalid parameter.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MACsec EPN splits the packet number (PN) into two 32-bits fields,
epn_lsb (32 least significant bits (LSBs) of PN) and epn_msb (32
most significant bits (MSBs) of PN).
Epn_msb bits are managed by SW and for that HW is required to send
an object change event of type EPN event notifying the SW to update
the epn_msb in addition, once epn_msb is updated SW update HW with
the new epn_msb value for HW to perform replay protection.
To prevent HW from stopping while handling the event, SW manages
another bit for HW called epn_overlap, HW uses the latter to get
an indication regarding how to read the epn_msb value correctly
while still receiving packets.
Add epn event handling that updates the epn_overlap and epn_msb for
every 2^31 packets according to the following logic:
if epn_lsb crosses 2^31 (half sequence number wraparound) upon HW
relevant event, SW updates the esn_overlap value to OLD (value = 1).
When the epn_lsb crosses 2^32 (full sequence number wraparound)
upon HW relevant event, SW updates the esn_overlap to NEW
(value = 0) and increment the esn_msb.
When using MACsec EPN a salt and short secure channel id (ssci)
needs to be provided by the user, when offloading EPN need to pass
this salt and ssci to the HW to be used in the initial vector (IV)
calculations.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Postpone MACsec initialization to the mlx5e profile enable stage to have
user access region (UAR) pages and other resources ready before MACsec
initialization to initialize advanced steering operation (ASO) hardware
resources.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for ASO work queue entry (WQE) data to allow reading
data upon querying the ASO work queue (WQ).
Register user mode memory registration (UMR) upon ASO WQ init,
de-register UMR upon ASO WQ cleanup.
MACsec uses UMR to determine the cause of the event triggered
by the HW since different scenarios could trigger the same event.
Setup MACsec ASO object to sync HW with SW about various macsec
flow stateful features like: replay window, lifetime limits e.t.c
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
