i219 (4) and i219 (5) are the next LOM generations that will be
available on the next Intel platform (KabeLake).
This patch provides the initial support for the devices.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been bugs caused by HW ULP configuration settings not being
properly cleared after cable connect in V-Pro capable systems.
This caused HW to get out of sync occasionally.
The fix ensures that ULP settings are cleared in HW after
LAN cable re-connect.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on feedback from HW team, the configured value of the internal PHY
HW FIFO pointer gap was incorrect for non-gig speeds.
This patch provides the correct configuration.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several packet loss issues were reported for which the root cause for
them was an incorrect configuration of internal HW PHY clock gating
mechanism by SW.
This patch provides the correct mechanism.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to system level changes introduced in Skylake, ULP exit takes
significantly longer to occur. Therefore, driver must wait longer for.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the introduction of 82574 support in e1000e, the driver has worked
on the assumption that msi-x interrupt generation is automatically
disabled after each irq. As it turns out, this is not the case.
Currently, rx interrupts can fire multiple times before and during napi
processing. This can be a problem for users because frames that arrive
in a certain window (after adapter->clean_rx() but before
napi_complete_done() has cleared NAPI_STATE_SCHED) generate an interrupt
which does not lead to napi_schedule(). These frames sit in the rx queue
until another frame arrives (a tcp retransmit for example).
While the EIAC and CTRL_EXT registers are properly configured for irq
automask, the modification of IAM in e1000_configure_msix() is what
prevents automask from working as intended.
This patch removes that erroneous write and fixes interrupt rearming for
tx interrupts. It also clears IAME from CTRL_EXT. This is not strictly
necessary for operation of the driver but it is to avoid disruption from
potential programs that access the registers directly, like `ethregs -c`.
Reported-by: Frank Steiner <steiner-reg@bio.ifi.lmu.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In msi-x mode, there is no handler for the lsc interrupt so there is no
point in writing that to ics now that we always assume Other interrupts
are caused by lsc.
Reviewed-by: Jasna Hodzic <jhodzic@ucdavis.edu>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the ICR read in the other interrupt handler, uses EIAC to
autoclear the Other bit from ICR and IMS. This allows us to avoid
interference with Rx and Tx interrupts in the Other interrupt handler.
The information read from ICR is not needed. IMS is configured such that
the only interrupt cause that can trigger the Other interrupt is Link
Status Change.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msi-x interrupts are not shared so there's no need to check if the
interrupt was really from this adapter.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function e1000e_up always returns 0. As such we can convert it to a
void and just ignore the results. This allows us to drop some code in a
couple spots as we no longer need to worry about non-zero return values.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219-LM (3) is a LOM that will be available on systems with the
Lewisburg Platform Controller Hub (PCH) chipset from Intel.
This patch provides the initial support for the device.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to timing changes to the ME firmware in Skylake, this timer
needs to be increased to 300ms.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes possible division by zero in receive
interrupt handler when working without adaptive interrupt
moderation.
The adaptive interrupt moderation mechanism is typically
disabled on jumbo MTUs.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Leonid Bloch <leonid@daynix.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The local variable 'ret' doesn't serve much purpose so we might as well
clean it up.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting ndo_features_check to passthru_features_check allows the driver
to skip the check for multiple tagged TSO packets and enables stacked
VLAN TSO.
Tested with I217-LM.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When e1000e_setup_rx_resources is failed in e1000_open,
e1000e_free_tx_resources in "err_setup_rx" segment is executed.
"writel(0, tx_ring->head)" statement in e1000_clean_tx_ring
in e1000e_free_tx_resources will cause a null poonter dereference(crash),
because "tx_ring->head" is only assigned in e1000_configure_tx
in e1000_configure, but it is after e1000e_setup_rx_resources.
This patch moves head/tail register writing to e1000_configure_tx/rx,
which can fix this problem. It is inspired by igb_configure_tx_ring
in the igb driver.
Specially, thank Alexander Duyck for his valuable suggestion.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver lacks pm_qos_remove_request in error handling (err_req_irq) of
e1000_open, and qos request inserted by pm_qos_add_request is not removed.
This patch add pm_qos_remove_request in error handling to fix it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected. In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The condition under which the flush should occur was reversed. The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.
If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2c6544829 moved pm_qos_req to e1000_adapter. Add the header file
that defines the struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using s64 for lat_ns (latency nano-second value) since in
our calculations a negative value could be a resultant. For negative
values, we then assign lat_ns to be zero, so the value passed to
do_div() was never negative, but do_div() expects the argument type
to be u64, so do a cast to resolve a compile warning seen on
PowerPC.
CC: Yanjiang Jin <yanjiang.jin@windriver.com>
CC: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reported-by: Yanjiang Jin <yanjiang.jin@windriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The driver wasn't allowing jumbo frames to be
enabled when CRC stripping was disabled, however it was allowing CRC
stripping to be disabled while jumbo frames were enabled. This fixes that by
making it so that the NETIF_F_RXFCS flag cannot be set when jumbo frames are
enabled on 82579 and newer parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VLAN_HLEN was added to the calculation for the maximum frame size
there seems to have been a number of issues added to the driver.
The first issue is that in some cases the maximum frame size for a device
never really reached the actual maximum frame size as the VLAN header
length was not included the calculation for that value. As a result some
parts only supported a maximum frame size of either 1496 in the case of
parts that didn't support jumbo frames, and 8996 in the case of the parts
that do.
The second issue is the fact that there were several checks that weren't
updated so as a result setting an MTU of 1500 was treated as enabling jumbo
frames as the calculated value was 1522 instead of 1518. I have addressed
those by replacing ETH_FRAME_LEN with VLAN_ETH_FRAME_LEN where appropriate.
The final issue was the fact that lowering the MTU below 1500 would cause
the driver to allocate 2K buffers for the rings. This is an old issue that
was fixed several years ago in igb/ixgbe and I am addressing now by just
replacing == with a <= so that we always just round up to 1522 for anything
that isn't a jumbo frame.
Fixes: c751a3d58c ("e1000e: Correctly include VLAN_HLEN when changing interface MTU")
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e is the only driver requiring pm_qos_req, instead of causing
every device to waste up to 240 bytes. Allocate it for the specific
driver.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to rmb with dma_rmb in the case where we want to
order all follow-on descriptor reads after the check for the descriptor
status bit.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed two warnings in e1000e and igb, when switching to timespec64
some printf formats started to not match. In theses cases actually
the new type is __kernel_time_t which is __kernel_long_t which
unfortunately can be either "long" or "long long". So to solve
this I cases the arguments to "long long". -DaveM
Richard Cochran says:
====================
ptp: get ready for 2038
This series converts the core driver methods of the PTP Hardware Clock
(PHC) subsystem to use the 64 bit version of the timespec structure,
making the core API ready for the year 2038.
In addition, I reviewed how each driver and device represents the time
value at the hardware register level. Most of the drivers are ready,
but a few will need some work before the year 2038, as shown:
Patch Driver
------------------------------------------------
12 drivers/net/ethernet/intel/igb/igb_ptp.c
15 ? drivers/net/ethernet/sfc/ptp.c
16 drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c
The commit log messages document how each driver is ready or why it is
not ready. For patch 15, I could not easily find out the hardware
representation of the time value, and so the SFC maintainers will have
to review their low level code in order to resolve any remaining
issues.
* ChangeLog
** V3
- dp83640: use timespec64 throughout per Arnd's suggestion
- tilegx: use timespec64 throughout per Chris' suggestion
- add Jeff's acked-bys
** V2
- use the new methods in the posix clock code right away (patch #3)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
