Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.
[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds vendor-prefix for Wexler.
WEXLER trademark owned by AVIRSA Electronics, a member of the
diversified holding AVIRSA.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add support for Wexler TAB7200 tablet.
The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The touchscreen controller in the A13 and later has a different temperature
curve than the one in the original A10, change the compatible for the A13 and
later so that the kernel will use the correct curve.
Reported-by: Tong Zhang <lovewilliam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a cubietech vendor prefix, as it is missing. The cubietruck, cubieboard2,
and cubieboard all already reference this prefix.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
lcd screen, 512MB RAM & 4GB emmc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The auxtek-t004:
http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
a 2 micro-usb receptacles, one for power and one for USB OTG.
The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add A13 mmc2 pinmux settings, note these are for a 8bit bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13 and the A10s use the same die (this has been confirmed by Allwinner),
as such there is no need to differentiate between the ehci/ohci parts of both,
the only reasons there were different allwinner,sun5i-a*-foo compatible
between these 2 parts is costemetically and because we could when we still
had 2 completely different dtsi files.
The allwinner,sun5i-a*-foo compatible strings are not used for binding at all,
the actual driver binds to the generic-?hci compatible, so we can safely remove
this cosmetical difference and simplify the dtsi files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM,
8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using
USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out,
a TRS connector for A/V, SPDIF and IrDA.
This patch adds basic support for the device, more information can
be found here (http://linux-sunxi.org/Mele_I7).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s and the A13 are very similar SoCs, the only difference being the
number of pins and the number of devices available (number of UARTs, EMAC only
in the A10s, etc.), and the clocks and pinctrl functions obviously.
Create a common DTSI that will be included by the A10s and A13 DTSI, that will
add their SoC differences in there.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Optimus board, all three USB hosts can be used.
HCI0 and HCI2 are available through the USB connector.
HCI1 is available with HSIC through 2 pins on the GPIO
expansion header.
This patch also adds a regulator for HCI2/USB3's VBUS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zalan Blenessy <zalan.blenessy@gmail.com>
On sun9i, there are 3 independent usb phys for EHCI/OHCI.
Add device nodes for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB controller and phy clocks and resets have a separate address
block and driver. Add the nodes to represent them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Wills Wang <wills.wang.open@gmail.com>
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost
Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM,
4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and
another for power in, HDMI, SATA, 5V power for SATA devices, gigabit
Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.
For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano
Changes in v3:
- rename LEDs to pcduino3-nano:green:usr[12]
- remove optional features on Arduino headers (i2c2, spi0, uart2)
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot,
miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and
3.5mm headphone jack.
Changes since v2:
* Fix syntax error (brown paper bag release)
Changes since v1:
* Added sun4i-lradc keymap
* Added TODO note about missing IRQ pins for bma250
* Fixed formatting issues and removed external URLs
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
