Guest OS builds up its timing mode list based on the virtual EDID as
simulated by GVT. However since there are several timings supported in
the virtual EDID, and each timing can also support several modes
(resolution and refresh rate), current emulated vblank period (16ms)
may not always be correct and could lead to miss-sync behavior in guest.
Guest driver will setup new resolution and program vregs accordingly and
it should always follows GEN PRM. Based on the simulated display regs by
GVT, it's safe to decode the actual refresh rate using by guest from
vreg only.
Current implementation only enables PIPE_A and PIPE_A is always tied to
TRANSCODER_A in HW. GVT may simulate DP monitor on PORT_B or PORT_D
based on the caller. So we can find out which DPLL is used by PORT_x
which connected to TRANSCODER_A and calculate the DP bit rate from the
DPLL frequency. Then DP stream clock (pixel clock) can be calculated
from DP link M/N and DP bit rate. Finally, get the refresh rate from
pixel clock, H total and V total.
The per-vGPU accurate refresh rate is not used yet but only stored,
until per-vGPU vblank timer is enabled. Then each vGPU can have
different and accurate refresh rate per-guest driver configuration.
Refer to PRM for GEN display and VESA timing standard for more details.
V2:
Rebase to 5.11.
Correctly calculate DP link rate for BDW and BXT.
Use GVT_DEFAULT_REFRESH_RATE instead of hardcoded to 60 as init refresh.
Typo fix. (zhenyu)
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210226044559.283622-1-colin.xu@intel.com
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
In Bspec the TGL TypeC ports are TC1-6, the AUX power well request flags
are USBC1-6/TBT1-6, so for clarity use these names in the port power
domain names instead of the D-I terminology (which Bspec uses only for
the ICL TypeC ports).
A domain name should follow the <domain>_<pipe/transcoder/port/aux_ch>
format. Add the new aliases based on this, leaving a change to rename
all the rest accordingly for a follow-up.
No functional change.
v2: Add comment to commit log about unifying domain names. (Jose)
Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222210400.940158-1-imre.deak@intel.com
Even though GEN12+ HW supports PSR + DC3CO, DMC's HW DC3CO exit mechanism
has an issue with using of Selective Fecth and PSR2 manual tracking.
And as some GEN12+ platforms (RKL, ADL-S) don't support PSR2 HW tracking,
Selective Fetch will be enabled by default on that platforms.
Therefore if the system enables PSR Selective Fetch / PSR manual tracking,
it does not allow DC3CO dc state, in that case.
When this DC3CO exit issue is addressed while PSR Selective Fetch is
enabled, this restriction should be removed.
v2: Address Jose's review comment.
- Fix typo
- Move check routine of DC3CO ability to
tgl_dc3co_exitline_compute_config()
v3: Change the check routine of enablement of psr2 sel fetch. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222213006.1609085-1-gwan-gyeong.mun@intel.com
Read and debug log the eDP sink MSO configuration. Do not actually do
anything with the information yet besides logging.
FIXME: The pixel overlap is present in DisplayID 2.0, but we don't have
parsing for that. Assume zero for now. We could also add quirks for
non-zero pixel overlap before DisplayID 2.0 parsing.
v3: Add placeholder for pixel overlap.
v2: Rename intel_dp_mso_init -> intel_edp_mso_init
Cc: Nischal Varide <nischal.varide@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/24ef61574e5af12cd86d5b85afbfbd4ac2f9de25.1613054234.git.jani.nikula@intel.com
This will set the right value of source_support when the port
encoder/port supports PSR but sink don't.
This change will also be needed in future for panel replay as psr
struct needs to be initialized even if disconnected or current sink
don't support PSR.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-4-jose.souza@intel.com
If source_support is set the platform supports PSR so no need to check
it again at every CAN_PSR().
Also removing the intel_dp_is_edp() calls, if sink_support is set
the sink connected is for sure a eDP panel.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-3-jose.souza@intel.com
There is no support for two pipes one transcoder for PSR and if we had
that the current code should not use cpu_transcoder.
Also I can't see a scenario where crtc_state->enable_psr2_sel_fetch is
set and PSR is not enabled and if by a bug it happens PSR HW will just
ignore any value in set in PSR2_MAN_TRK_CTL.
So dropping all the rest and keeping the same behavior that we have
with intel_psr2_program_plane_sel_fetch().
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-2-jose.souza@intel.com
Right now CI is blacklisting module reload, so we need to be able to
enable PSR2 selective fetch in run time to test this feature before
enable it by default.
Changes in IGT will also be needed.
v2:
- Fixed handling of I915_PSR_DEBUG_ENABLE_SEL_FETCH in
intel_psr_debug_set()
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209205036.351076-1-jose.souza@intel.com
According to Bspec #20124, max link rate table for DP was updated
at BDB version 230. Max link rate can support upto UHBR.
After migrate to BDB v230, the definition for LBR, HBR2 and HBR3
were changed. For backward compatibility. If BDB version was
from 216 to 229. Driver have to follow original rule to configure
DP max link rate value from VBT.
v2: split the mapping table to two for old and new BDB definition.
v3: return link rate instead of assigning it.
v4: remove the useless variable.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
[vsyrjala: Try to retain the comment that VBT version 216 added some of this]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210218052333.16109-1-shawn.c.lee@intel.com
When we sanitize planes let's wait for the scanout to stop
before we let the subsequent code tear down the ggtt mappings
and whatnot. Cures an underrun on my ivb when I boot with
VT-d enabled and the BIOS fb gets thrown out due to stolen
being considered unusable with VT-d active.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210217162050.13803-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We tend to use output_format!=RGB as a shorthand for YCbCr, but
this fails if we have a disabled crtc where output_format==INVALID.
We're now getting some fail from intel_color_check() when we have:
hw.enable==false
hw.ctm!=NULL
output_format==INVALID
Let's avoid that by throwing INTEL_OUTPUT_FORMAT_INVALID to the
dumpster, and thus everything defaults to RGB when the crtc
is disabled.
This does beg the deeper question of how much of the state
should we in fact be validating when hw/uapi.enable==false.
And should we even be doing the uapi->hw copy when
uapi.enable==false? So far I've not been able to come up with
satisfactory answers for myself, so I'm putting it off for the
moment.
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: 0aa5c3835c ("drm/i915: support two CSC module on gen11 and later")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2964
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205202322.27608-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
-Wunintialized was disabled in commit c562746149 ("drm/i915: Disable
-Wuninitialized") because there were two warnings that were false
positives. The first was due to DECLARE_WAIT_QUEUE_HEAD_ONSTACK, which
was fixed in LLVM 9.0.0. The second was in busywait_stop, which was
fixed in LLVM 10.0.0 (issue 415). The kernel's minimum version for LLVM
is 10.0.1 so this warning can be safely enabled, where it has already
caught a couple bugs.
Link: https://github.com/ClangBuiltLinux/linux/issues/220
Link: https://github.com/ClangBuiltLinux/linux/issues/415
Link: https://github.com/ClangBuiltLinux/linux/issues/499
Link: 2e040398f8
Link: c667cdc850
Fixes: c562746149 ("drm/i915: Disable -Wuninitialized")
References: 2ea4a7ba9b ("drm/i915/gt: Avoid uninitialized use of rpcurupei in frequency_show")
References: 2034c2129b ("drm/i915/display: Ensure that ret is always initialized in icl_combo_phy_verify_state")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216212953.24458-1-nathan@kernel.org
Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.
We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com
Since .{enable,disable}_clock() are already vfuncs it's a bit silly to
have if-ladders inside them. Just provide specialized version for adl-s
and rkl so we don't need any of that.
v2: s/dev_priv/i915/ (Lucas)
Fix typos in platform names (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-13-ville.syrjala@linux.intel.com
The other DDI .enable_clock() functions are trying to protect us
against pll==NULL. A bit tempted to throw out all the WARNs as
just unnecessary noise, but I guess they might have some use
when poking around the shared_dpll code (not sure it wouldn't
oops elsewhere though). So let's unify it all and sprinkle in
the missing WARNs for icl/dg1.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-11-ville.syrjala@linux.intel.com
The current code attempts to protect the RMWs into global
clock routing registers with a mutex, but forgets to do so
in a few places. Let's remedy that.
Note that at the moment we serialize all modesets onto single
wq, so this shouldn't actually matter. But maybe one day we
wish to attempt parallel modesets again...
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-10-ville.syrjala@linux.intel.com
For ICL+ we have several styles of clock routing for DDIs:
1) TC DDI + TC PHY
-> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}()
and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports()
2) ICL/TGL combo DDI + combo PHY
-> just need the stuff from icl_{map,unmap}_plls_to_ports()
3) JSL/EHL TC DDI + combo PHY
-> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and
the full combo style clock selection from icl_{map,unmap}_plls_to_ports()
4) ADLS/RKL
-> these use both TC and combo DDIs with combo PHYs, however they
always use the full combo style clock selection as per
icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all,
thus get treated the same as 2)
We extract all that from the current mess in the following way:
1) icl_ddi_tc_{enable,disable}_clock()
2) icl_ddi_combo_{enable,disable}_clock()
3) jsl_ddi_tc_{enable,disable}_clock()
4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here
v2: s/dev_priv/i915/ (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-8-ville.syrjala@linux.intel.com
Yank out the HSW/BDW code from intel_ddi_clk_{select,disable}()
and put it into the new encoder .{enable,disable}_clock() vfuncs.
v2: s/dev_priv/i915/ (Lucas)
v3: Deal with FDI
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-4-ville.syrjala@linux.intel.com
The current code dealing with the clock routing for DDI encoders
is a maintenance nightmare. Let's start cleaning it up by allowing
the encoder to provide vfuncs for enablign/disabling the clock.
We leave them initially unimplemented, falling back to the old
if-else approach.
v2: Convert the FDI enable sequence
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-3-ville.syrjala@linux.intel.com
We want to put all DDI clock routing code into one place.
Unify the FDI enable sequence to use the standard function
instead of hand rolling its own. The disable sequence already
uses the normal thing.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
intel_init_audio_hooks() sets up hooks in the display struct and only
makes sense when we have display. Move it inside
intel_init_display_hooks() so it isn't called when we don't have
display.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-4-lucas.demarchi@intel.com
Now that all display-related functions are grouped in
i915_driver_register(), move them to display/ so we reduce the amount of
display calls from the rest of the driver.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-3-lucas.demarchi@intel.com
intel_gt_driver_register() may be called earlier than
intel_opregion_register() and acpi_video_register(), so move it up.
intel_display_debugfs_register() may be called later, together with the
other display-related initializations. There is a slight change in
behavior that sysfs files will show up before the display-related
debugfs files, but that shouldn't be a problem - userspace shouldn't be
relying in debugfs.
This allows us to group all the display-related calls under a single
check for "HAS_DISPLAY()" that can be later moved to a better place.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20210213042756.953007-2-lucas.demarchi@intel.com
In rare circumstances bugs in PCI programming, broken BIOS, or failing
hardware can cause the CPU to lose access to the MMIO BAR on dgfx
platforms. This is a pretty catastrophic failure since all register
reads come back with values of 0xFFFFFFFF. Let's check for this special
case while doing our usual checks for unclaimed registers; the FPGA_DBG
register we use for those checks on modern platforms has some unused
bits that will always read back as 0 when things are behaving properly;
we can use them as canaries to detect when MMIO itself has suddenly
broken and try to print a more informative error message in the logs.
v2: Let the detection function still return 'true' if we've lost our
MMIO access. We'll still get an extra false positive message about
an unclaimed register access, but we'll still honor the 'mmio_debug'
limit and not spam the log. (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210212211925.3418280-2-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Although the bspec's description doesn't make it very clear, the
hardware architects have confirmed that the FPGA_DBG register that we
use to check for unclaimed MMIO accesses is display-specific and will
only properly flag unclaimed MMIO transactions for registers in the
display range. If a platform doesn't have display, FPGA_DBG itself will
not be available and should not be checked. Let's move the feature flag
into intel_device_info.display to more accurately reflect this.
Given that we now know FPGA_DBG is display-specific, it could be argued
that we should only check it on out intel_de_*() functions. However
let's not make that change right now; keeping the checks in all of the
existing locations still helps us catch cases where regular
intel_uncore_*() functions use bad MMIO offset math / base addresses and
accidentally wind up landing within an unused area within the display
MMIO range. It will also help catch cases where userspace-initiated
MMIO (e.g., IGT's intel_reg tool) attempt to read bad offsets within the
display range.
v2: Add missing hunk with the update to the HAS_FPGA_DBG_UNCLAIMED
macro. (CI)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210212222049.3516344-1-matthew.d.roper@intel.com
Apparently the new gen9_bc platforms that Intel has introduced don't
provide us with a STRAP config register to read from for initializing DDI
B, C, and D detection. So, workaround this by hard-coding our strap config
in intel_setup_outputs().
Changes since v4:
* Split this into it's own commit
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-5-lyude@redhat.com
Next, let's start introducing the HPD pin mappings for Intel's new gen9_bc
platform in order to make hotplugging display connectors work. Since
gen9_bc is just a TGP PCH along with a CML CPU, except with the same HPD
mappings as ICL, we simply add a skl_hpd_pin function that is shared
between gen9 and gen9_bc which handles both the traditional gen9 HPD pin
mappings and the Icelake HPD pin mappings that gen9_bc uses.
Changes since v4:
* Split this into its own commit
* Introduce skl_hpd_pin() like vsyrjala suggested and use that instead of
sticking our HPD pin mappings in TGP code
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-4-lyude@redhat.com
After fixing the OA_TAIL_PTR corruption, there are no more reports with
reason field of zero. Drop the check for report reason.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210190106.8586-1-umesh.nerlige.ramappa@intel.com
DP-MST connector encoder initializes at modeset
Adding a connector->encoder NULL check in order to
avoid any NULL pointer dereference.
intel_hdcp_enable() already handle this but debugfs
can also invoke the intel_{hdcp,hdcp2_capable}.
Handling it gracefully.
v2:
- Use necessary lock and NULL check in
i915_hdcp_sink_capability_show. [Imre]
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210211140502.22786-1-anshuman.gupta@intel.com
We are not checking for specific SKUs and feedback from HW team is that
it may not work since it was supposed to be fixed by the same time
straps stopped to be used. So, just update comment.
v2: Instead of removing the check, just update the comment since
feedback from HW team was that it actually may not work
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625001120.22810-3-lucas.demarchi@intel.com
With the introduction of gen9_bc, where Intel combines Cometlake CPUs with
a Tigerpoint PCH, we'll need to introduce new DDC pin mappings for this
platform in order to make all of the display connectors work. So, let's do
that.
Changes since v4:
* Split this into it's own patch - vsyrjala
Changes since v5:
* Rename gen9bc_port_to_ddc_pin() to gen9bc_tgp_port_to_ddc_pin()
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-3-lyude@redhat.com
Since Intel has introduced the gen9_bc platform, a combination of
Tigerpoint PCHs and CML CPUs, let's recognize such platforms as valid and
avoid WARNing on them.
Changes since v4:
* Split this into it's own patch - vsyrjala
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-2-lyude@redhat.com
Lane Reversal is required for some of the DDI ports. This information
is populated in VBT and driver should read the same and set the
polarity while enabling the port. This patch handles the same.
It helps fix a display blankout issue on DP ports on certain
platforms.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210211114209.23866-1-uma.shankar@intel.com
Set the right BW buddy page mask for new memory types.
BSpec: 49218
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209174238.153278-1-jose.souza@intel.com
We don't have a persistent fb holding a reference to the frontbuffer
object, so every time we do the get+put we throw the frontbuffer object
immediately away. And so the next time around we get a pristine
frontbuffer object with bits==0 even for the old vma. This confuses
the frontbuffer tracking code which understandably expects the old
frontbuffer to have the overlay's bit set.
Fix this by hanging on to the frontbuffer reference until the next
flip. And just to make this a bit more clear let's track the frontbuffer
explicitly instead of just grabbing it via the old vma.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1136
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-2-ville.syrjala@linux.intel.com
Fixes: 8e7cb1799b ("drm/i915: Extract intel_frontbuffer active tracking")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
