The motivation at this point is mainly native userspace mesa driver in a
VM guest. The one remaining synchronous "hotpath" is buffer allocation,
because guest needs to wait to know the bo's iova before it can start
emitting cmdstream/state that references the new bo. By allocating the
iova in the guest userspace, we no longer need to wait for a response
from the host, but can just rely on the allocation request being
processed before the cmdstream submission. Allocation failures (OoM,
etc) would just be treated as context-lost (ie. GL_GUILTY_CONTEXT_RESET)
or subsequent allocations (or readpix, etc) can raise GL_OUT_OF_MEMORY.
v2: Fix inuse check
v3: Change mismatched iova case to -EBUSY
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220411215849.297838-11-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
With userspace allocated iova (next patch), we can have a race condition
where userspace observes the fence completion and deletes the vma before
retire_submit() gets around to unpinning the vma. To handle this, add a
fenced unpin which drops the refcount but tracks the fence, and update
msm_gem_vma_inuse() to check any previously unsignaled fences.
v2: Fix inuse underflow (duplicate unpin)
v3: Fix msm_job_run() vs submit_cleanup() race condition
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220411215849.297838-10-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the cause of using the GPU via virtgpu, the host side process is
really a sort of proxy, and not terribly interesting from the PoV of
crash/fault logging. Add a way to override these per process so that
we can see the guest process's name.
v2: Handle kmalloc failure, add comment to explain kstrdup returns
NULL if passed NULL [Dan Carpenter]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220317165144.222101-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
refcount_t complains about 0->1 transitions, which isn't *quite* what we
wanted. So use dirtyfb==1 to mean that the fb is not connected to any
output that requires dirtyfb flushing, so that we can keep the underflow
and overflow checking.
Fixes: 9e4dde28e9 ("drm/msm: Avoid dirtyfb stalls on video mode displays (v2)")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220304202146.845566-1-robdclark@gmail.com
Add a way for userspace to specify the sequence number fence used to
track completion of the submit. As the seqno fence is simply an
incrementing counter which is local to the submitqueue, it is easy for
userspace to know the next value.
This is useful for native userspace drivers in a vm guest, as the guest
to host roundtrip can have high latency. Assigning the fence seqno in
the guest userspace allows the guest to continue without waiting for
response from the host.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220224222321.60653-1-robdclark@gmail.com
Add a SYSPROF param for system profiling tools like Mesa's pps-producer
(perfetto) to control behavior related to system-wide performance
counter collection. In particular, for profiling, one wants to ensure
that GPU context switches do not effect perfcounter state, and might
want to suppress suspend (which would cause counters to lose state).
v2: Swap the order in msm_file_private_set_sysprof() [sboyd] and
initialize the sysprof_active refcount to one (because the under/
overflow checking in refcount_t doesn't expect a 0->1 transition)
meaning that values greater than 1 means sysprof is active.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220304005317.776110-4-robdclark@gmail.com
We're experimenting a bit with the process this time, with Dmitry
collecting display patches and merging them into msm-next with me
handling the gpu/etc side of things. Summary of interesting new bits
and pieces
* dpu + dp support for sc8180x
* dp support for sm8350
* dpu + dsi support for qcm2290
* 10nm dsi phy tuning support
* bridge support for dp encoder
* gpu support for additional 7c3 SKUs
* assorted cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGu=Jdrw6DqYOYPTMks7=zatrsvdR=o6DpjqZ=TQQhFZuw@mail.gmail.com
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Improve performance of some fbdev ops, in some cases up to 6x faster.
Core Changes:
- Some small DP fixes.
- Find panels in subnodes of OF devices, and add of_get_drm_panel_display_mode
to retrieve mode.
- Add drm_object_property_get_default_value and use it for resetting
zpos in plane state reset, removing the need for individual drivers
to do it.
- Same for color encoding and color range props.
- Update panic handling todo doc.
- Add todo that format conversion helpers should be sped up similarly to fbdev ops.
Driver Changes:
- Add panel orientation property to simpledrm for quirked panels.
- Assorted small fixes to tiny/repaper, nouveau, stm, omap, ssd130x.
- Add crc support to stm/ltdc.
- Add MIPI DBI compatible SPI driver
- Assorted small fixes to tiny panels and bridge drivers.
- Add AST2600 support to aspeed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/48fabd78-ade9-f80b-c724-13726c7be69e@linux.intel.com
Someone on IRC once asked an innocent enough sounding question: Why
with xf86-video-modesetting is es2gears limited at 120fps.
So I broke out the perfetto tracing mesa MR and took a look. It turns
out the problem was drm_atomic_helper_dirtyfb(), which would end up
waiting for vblank.. es2gears would rapidly push two frames to Xorg,
which would blit them to screen and in idle hook (I assume) call the
DIRTYFB ioctl. Which in turn would do an atomic update to flush the
dirty rects, which would stall until the next vblank. And then the
whole process would repeat.
But this is a bit silly, we only need dirtyfb for command mode DSI
panels. So track in plane state whether dirtyfb is required, and
track in the fb how many attached planes require dirtyfb so that we
can skip it when not required. (Note, mdp4 does not actually have
cmd mode support.)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220223191118.881321-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
Other processes don't need to know about faults that they are isolated
from by virtue of address space isolation. They are only interested in
whether some of their state might have been corrupted.
But to be safe, also track unattributed faults. This case should really
never happen unless there is a kernel bug (and that would never happen,
right?)
v2: Instead of adding a new param, just change the behavior of the
existing param to match what userspace actually wants [anholt]
Closes: https://gitlab.freedesktop.org/mesa/mesa/-/issues/5934
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220201161618.778455-3-robdclark@gmail.com
Reviewed-by: Emma Anholt <emma@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently DP driver will allocate panel bridge for eDP panels. This
supports only the following topology:
- eDP encoder ⇒ eDP panel (wrapped using panel-bridge)
Simplify this code to just check if there is any next bridge in the
chain (be it a panel bridge or regular bridge). Rename panel_bridge
field to next_bridge accordingly.
This allows one to use e.g. one of the following display topologies:
- eDP encoder ⇒ ptn3460 ⇒ fixed LVDS panel
- eDP encoder ⇒ ptn3460 ⇒ LVDS connector with EDID lines for panel autodetect
- eDP encoder ⇒ ptn3460 ⇒ THC63LVD1024 ⇒ DPI panel.
- eDP encoder ⇒ LT8912 ⇒ DSI panel
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220211224006.1797846-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In commit 8a3b4c17f8 ("drm/msm/dp: employ bridge mechanism for display
enable and disable") the DP driver received a drm_bridge instance, which
is always attached to the encoder as a root bridge. However it conflicts
with the panel_bridge support for eDP panels. The panel bridge attaches
to the encoder before the "dp" bridge (DP driver's drm_bridge instance
created in msm_dp_bridge_init()) has a chance to do so. Change
panel bridge attachment to come after the "dp" bridge attachment (and to
use it as a previous bridge).
Fixes: 8a3b4c17f8 ("drm/msm/dp: employ bridge mechanism for display enable and disable")
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220211224006.1797846-2-dmitry.baryshkov@linaro.org
[db: fixed commit message according to Stephen's suggestions]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In function dpu_encoder_phys_cmd_wait_for_commit_done we are always
checking if the relative CTL is started by waiting for an interrupt
to fire: it is fine to do that, but then sometimes we call this
function while the CTL is up and has never been put down, but that
interrupt gets raised only when the CTL gets a state change from
0 to 1 (disabled to enabled), so we're going to wait for something
that will never happen on its own.
Solving this while avoiding to restart the CTL is actually possible
and can be done by just checking if it is already up and running
when the wait_for_commit_done function is called: in this case, so,
if the CTL was already running, we can say that the commit is done
if the command transmission is complete (in other terms, if the
interface has been flushed).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210911163919.47173-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
