The new version of alloc_ep_req() already aligns the buffer size to
wMaxPacketSize on OUT endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Using usb_ep_align() makes sure that the buffer size for OUT endpoints is
always aligned with wMaxPacketSize (512 usually). This makes sure
that no buffer has the wrong size, which can cause nasty bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Length of buffers should be of type size_t whenever possible. Altough
recommended, this change has no real practical change, unless a driver has a
uses a huge or negative buffer size - it might help find these bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduce an attribute "inquiry_string" to the lun.
In some environments, e. g. BIOS boot menus, the inquiry string
is the only information about devices presented to the user. The
default string depends on the "cdrom" bit of the first lun as
well as the kernel version and allows no further customization.
So without access to the client it is not obvious which gadget is
active at a given point and what any of the available luns might
contain.
If "inquiry_string" is ignored or set to the empty string, the
old behavior is preserved.
Signed-off-by: Philipp Gesang <philipp.gesang@intra2net.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With composite gadget (ACM + NCM), USB3380 to host TCP transfer
speed dropped to 150 Mbit/s compared to 900 Mbit/s with NCM
gadget. Problem seems to be that net2280/USB3380 has only four
DMA channels and those DMA channels are allocated to first HW
endpoints. Endpoint match function was mapping endpoint names
directly, so NCM did not get DMA for bulk endpoints.
This patch changed match_ep to prefer DMA enabled hw endpoints
for bulk usb endpoints and PIO for interrupt usb endpoints.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With SuperSpeed CDC NCM gadget, net2280 would get stuck in
'handle_ep_small' function. Triggering issue requires large
TCP transfer from host to USB3380.
Patch adds check for stuck condition and prevents hard lockup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the legacy behavior, and USB phy, upon detection a VBus signal, was
calling usb_gadget_vbus_(dis)connect().
This model doesn't work if the phy is generic and doesn't have an
adherence to the gadget API.
Instead of relying on the phy to call the gadget API, hook up the phy
notifier to report the VBus event, and upon it call the usb gadget API
ourselves.
This brings a new ordering problem, as before even if the usb_get_phy()
was failing because the UDC was probed before the phy, the phy would
call the gadget anyway, making the VBus connection event forwarded to
the gadget. Now we rely on the notifier, we have to ensure the
xxx_get_phy() does indeed work.
In order to cope with this, it is assumed that :
- for legacy platform_data machine, as the ordering cannot be ensured,
the phy must call usb_gadget_vbus_(dis)connect, such as
phy-gpio-vbus-usb.c
- for new devicetree platforms, we'll rely on the probe deferral, and
the phy can be gadget API agnostic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When usb gadget is set gadget serial function, it will be crash in below
situation.
It will clean the 'port->port_usb' pointer in gserial_disconnect() function
when usb link is inactive, but it will release lock for disabling the endpoints
in this function. Druing the lock release period, it maybe complete one request
to issue gs_write_complete()--->gs_start_tx() function, but the 'port->port_usb'
pointer had been set NULL, thus it will be crash in gs_start_tx() function.
This patch adds the 'port->port_usb' pointer checking in gs_start_tx() function
to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't assign -EINVAL to a u16.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
block any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the correct response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
[AmitP: Cherry-picked this patch and folded other relevant
fixes from Android common kernel android-4.4]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc device needs to be deleted if error occurs
Fixes: 855ed04a37 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'composite_os_desc_req_prepare', if one of the memory allocations fail,
0 will be returned, which means success.
We should return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If this memory allocation fail, we will return 0, which means success.
Return -ENOMEM instead.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When reading synchronously from a non-zero endpoint, gadgetfs will
return -EFAULT even if the read succeeds, due to a bad check of the
copy_to_iter() return value.
This fix compares the return value of copy_to_iter to the amount of
bytes that was passed, and only fails if they are not the same.
Signed-off-by: Binyamin Sharet <s.binyamin@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There may be a race condition if f_fs calls unregister_gadget_item in
ffs_closed() when unregister_gadget is called by UDC store at the same time.
this leads to a kernel NULL pointer dereference:
[ 310.644928] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 310.645053] init: Service 'adbd' is being killed...
[ 310.658938] pgd = c9528000
[ 310.662515] [00000004] *pgd=19451831, *pte=00000000, *ppte=00000000
[ 310.669702] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 310.675211] Modules linked in:
[ 310.678294] CPU: 0 PID: 1537 Comm: ->transport Not tainted 4.1.15-03725-g793404c #2
[ 310.685958] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 310.692493] task: c8e24200 ti: c945e000 task.ti: c945e000
[ 310.697911] PC is at usb_gadget_unregister_driver+0xb4/0xd0
[ 310.703502] LR is at __mutex_lock_slowpath+0x10c/0x16c
[ 310.708648] pc : [<c075efc0>] lr : [<c0bfb0bc>] psr: 600f0113
<snip..>
[ 311.565585] [<c075efc0>] (usb_gadget_unregister_driver) from [<c075e2b8>] (unregister_gadget_item+0x1c/0x34)
[ 311.575426] [<c075e2b8>] (unregister_gadget_item) from [<c076fcc8>] (ffs_closed+0x8c/0x9c)
[ 311.583702] [<c076fcc8>] (ffs_closed) from [<c07736b8>] (ffs_data_reset+0xc/0xa0)
[ 311.591194] [<c07736b8>] (ffs_data_reset) from [<c07738ac>] (ffs_data_closed+0x90/0xd0)
[ 311.599208] [<c07738ac>] (ffs_data_closed) from [<c07738f8>] (ffs_ep0_release+0xc/0x14)
[ 311.607224] [<c07738f8>] (ffs_ep0_release) from [<c023e030>] (__fput+0x80/0x1d0)
[ 311.614635] [<c023e030>] (__fput) from [<c014e688>] (task_work_run+0xb0/0xe8)
[ 311.621788] [<c014e688>] (task_work_run) from [<c010afdc>] (do_work_pending+0x7c/0xa4)
[ 311.629718] [<c010afdc>] (do_work_pending) from [<c010770c>] (work_pending+0xc/0x20)
for functions using functionFS, i.e. android adbd will close /dev/usb-ffs/adb/ep0
when usb IO thread fails, but switch adb from on to off also triggers write
"none" > UDC. These 2 operations both call unregister_gadget, which will lead
to the panic above.
add a mutex before calling unregister_gadget for api used in f_fs.
Signed-off-by: Winter Wang <wente.wang@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev->port_usb is checked for null pointer at above code, so dev->port_usb
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
cdev->config is checked for null pointer at above code, so cdev->config
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXlfJvAAoJEAhfPr2O5OEVtLUP/RpCQ+W3YVryIdmLkdmYXoY7
m2rXtUh7GmzBjaBkFzbRCGZtgROF7zl0e1R3nm4tLbCV4Becw8HO7YiMjqFJm9xr
b6IngIyshsHf60Eii3RpLqUFvYrc/DDIMeYf8miwj/PvFAfI2BV9apraexJlpUuI
wdyi28cfBHq4WYhubaXKoAyBQ8YRA/t8KNRAkDlifaOaMbSAxWHlmqoSmJWeQx73
KHkSvbRPu4Hjo3R6q/ab8VhqmXeSnbqnQB9lgnxz7AmAZGhOlMYeAhV/K2ZwbBH8
swv36RmJVO59Ov+vNR4p7GGGDL3+qk8JLj4LNVVfOcW0A+t7WrPQEmrL6VsyaZAy
/+r4NEOcQN6Z5nFwbr3E0tYJ2Y5jFHOvsBfKd3EEGwty+hCl634akgb0vqtg06cg
E2KG+XW983RBadVwEBnEudxJb0fWPWHGhXEqRrwOD+718FNmTqYM6dEvTEyxRup8
EtCLj+eQQ4LmAyZxWyE8A+keKoMFQlHqk9LN9vQ7t7Wxq9mQ+V2l12T/lN4VhdTq
4QZ4mrCMCGEvNcNzgSg6R/9lVb6RHDtMXZ3htbB/w+5xET/IKIANYyg1Hr7ahtdh
rTW/4q6n3jtsu6tp5poteFvPzZKAblbrj2EptVzZYkonQ5BeAUisFTtneUL10Jmj
EUf/sH0fqoOA0VvV6Tu+
=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return -ENOMEM if kmalloc() fails.
Fixes: 9353afbbfa ('usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a121.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a121 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_fs rounds up read(2) requests to a multiple of a max packet size
which means that host may provide more data than user has space for.
So far, the excess data has been silently ignored.
This introduces a buffer for a tail of such requests so that they are
returned on next read instead of being ignored.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a pr_err when host sent more data then the size of the buffer user
space gave us. This may happen on UDCs which require OUT requests to
be aligned to max packet size. The patch includes a description of the
situation.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_process_ep_req’:
drivers/usb/gadget/udc/mv_u3d_core.c:124:6: warning: variable ‘trb_complete’ set but not used [-Wunused-but-set-variable]
int trb_complete, actual, remaining_length = 0;
^
drivers/usb/gadget/udc/mv_u3d_core.c:123:28: warning: variable ‘curr_ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *curr_ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c:122:13: warning: variable ‘cur_deq_lo’ set but not used [-Wunused-but-set-variable]
dma_addr_t cur_deq_lo;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_enable’:
drivers/usb/gadget/udc/mv_u3d_core.c:530:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_disable’:
drivers/usb/gadget/udc/mv_u3d_core.c:636:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
In doing so, it removes calls to ioread32 function which does I/O with
the device, but I hope the reads don’t have any side effects that are
needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/r8a66597-udc.c: In function ‘r8a66597_irq’:
drivers/usb/gadget/udc/r8a66597-udc.c:1468:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/r8a66597-udc.c:1467:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to r8a66597_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_irq’:
drivers/usb/gadget/udc/m66592-udc.c:1203:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/m66592-udc.c:1202:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to m66592_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those are enabled with W=1 make option.
The patch leaves of some type-limits warnings which are caused by
generic macros used in a way where they produce always-false
conditions.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The "atmel,at91sam9g45-udc" compatible UDC is also used on at91sam9x5 so it
is also necessary to try to get the syscon for at91sam9x5-pmc.
Fixes: 4747639f01 ("usb: gadget: atmel: access the PMC using regmap")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We get a warning for this when building with W=1 because the
argument gets assigned to something else but never read:
drivers/usb/gadget/udc/pxa27x_udc.c: In function 'stop_activity':
drivers/usb/gadget/udc/pxa27x_udc.c:1828:74: error: parameter 'driver' set but not used [-Werror=unused-but-set-parameter]
This remove the argument entirely.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This new set of tracepoints will help all gadget
drivers and UDC drivers when problem appears. Note
that, in order to be able to add tracepoints to
udc-core.c we had to rename that to core.c and
statically link it with trace.c to form
udc-core.o. This is to make sure that module name
stays the same.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of defining all functions as static inlines,
let's move them to udc-core and export them with
EXPORT_SYMBOL_GPL, that way we can make sure that
only GPL drivers will use them.
As a side effect, it'll be nicer to add tracepoints
to the gadget API.
While at that, also fix Kconfig dependencies to
avoid randconfig build failures.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PLX USB2380 is a PCIe version of the NET2280 and behaves more like the
USB338x but without the USB3.0 superspeed support.
This was tested with g_ether, g_serial, g_mass_storage on a Gateworks
Ventana GW2383.
Cc: Justin DeFields <justindefields@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With a default size of 16kiB and with maximum of 32
buffers, we can transfer up to 512kiB, however Linux
can transfer up to 1MiB in a single mass storage
block transfer to USB3 storage devices.
Because of this, 1MiB block transfers end up being
slower than 512kiB block transfers. Let's increase
maximum number of storage buffers to a ridiculous
amount (256) so that anybody wanting to test maximum
achievable throughput can do so.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
valid range for storage buffers is encoded in
Kconfig already. Instead of checking again, let's
drop fsg_num_buffers_validate() altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In OS descriptors handling, if ctrl->bRequestType is
USB_RECIP_DEVICE and w_index != 0x4 or (w_value >> 8)
is true, it will not assign a valid value to req->length,
but use the default value(-EOPNOTSUPP), and queue an
OS desc request with the invalid req->length. It always
happens on the platforms which use os_desc (for example:
rk3366, rk3399), and cause kernel panic as follows
(use dwc3 driver):
Unable to handle kernel paging request at virtual address ffffffc0f7e00000
Internal error: Oops: 96000146 [#1] PREEMPT SMP
PC is at __dma_clean_range+0x18/0x30
LR is at __swiotlb_map_page+0x50/0x64
Call trace:
[<ffffffc0000930f8>] __dma_clean_range+0x18/0x30
[<ffffffc00062214c>] usb_gadget_map_request+0x134/0x1b0
[<ffffffc0005c289c>] __dwc3_ep0_do_control_data+0x110/0x14c
[<ffffffc0005c2d38>] __dwc3_gadget_ep0_queue+0x198/0x1b8
[<ffffffc0005c2e18>] dwc3_gadget_ep0_queue+0xc0/0xe8
[<ffffffc00061cfec>] composite_ep0_queue.constprop.14+0x34/0x98
[<ffffffc00061dfb0>] composite_setup+0xf60/0x100c
[<ffffffc0006204dc>] android_setup+0xd8/0x138
[<ffffffc0005c29a4>] dwc3_ep0_delegate_req+0x34/0x50
[<ffffffc0005c3534>] dwc3_ep0_interrupt+0x5dc/0xb58
[<ffffffc0005c0c3c>] dwc3_thread_interrupt+0x15c/0xa24
With this patch, the gadget driver will not queue
a request and return immediately if req->length is
invalid. And the usb controller driver can handle
the unsupport request correctly.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If c->cdev->use_os_string flag is not set,
don't need to invoke ffs_do_os_descs() in _ffs_func_bind.
So uninitialized ext_compat_id pointer won't be accessed by
__ffs_func_bind_do_os_desc to cause kernel panic.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit dc8c46a5ae ("usb: gadget: f_tcm: convert to new function
interface with backward compatibility") introduced a possible out
of bounds memory access:
If tpg is not found in function usbg_drop_tpg,
tpg_instances[TPG_INSTANCES] is accessed.
Fixes: dc8c46a5ae ("usb: gadget: f_tcm: convert to new function interface with backward compatibility")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Function in_rq_cur copies random bytes from the stack.
Zero the memory instead.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current __ffs_data_do_os_desc() of f_fs.c will check reserved1 field
of OS_DESC_EXT_COMPAT and return -EINVAL if it's 1.
But MS OS 1.0 Descriptors
http://msdn.microsoft.com/en-us/library/windows/hardware/gg463179.aspx
defines that field to be 1.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Device qualifier descriptor is now generated by composite.c
code. So let's fix this old comment by removing parts which
are no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This descriptor is never used. Currently device qualifier
descriptor is generated by compossite code, so no need to
keep it in function file.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Krzysztof Opasiak <kopasiak90@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This loop is supposed to set all the .num[] values to -1 but it's off by
one so it skips the first element and sets one element past the end of
the array.
I've cleaned up the loop a little as well.
Fixes: ddf8abd259 ('USB: f_fs: the FunctionFS driver')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default user could store only valid UDC name in configfs UDC
attr by doing:
echo $UDC_NAME > UDC
Commit (855ed04 "usb: gadget: udc-core: independent registration of
gadgets and gadget drivers") broke this behavior and allowed to store
any arbitrary string in UDC file and udc core was waiting for such
controller to appear.
echo "any arbitrary string here" > UDC
This commit fix this by adding a flag which prevents configfs
gadget from being added to list of pending drivers if UDC with
given name has not been found.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.
The highlights this round include:
- Allow external PR/ALUA metadata path be defined at runtime via top
level configfs attribute (Lee)
- Fix target session shutdown bug for ib_srpt multi-channel (hch)
- Make TFO close_session() and shutdown_session() optional (hch)
- Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
(hch)
- Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
- Refactor iscsi-target RX/TX PDU encode/decode into common code
(Varun)
- Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
validate_parameters, and get_r2t_ttt for generic ISO offload
(Varun)
- Initial merge of cxgb iscsi-segment offload target driver (Varun)
The bulk of the changes are Chelsio's new driver, along with a number
of iscsi-target common code improvements made by Varun + Co along the
way"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
iscsi-target: Convert transport drivers to signal rdma_shutdown
iscsi-target: Make iscsi_tpg_np driver show/store use generic code
tcm_qla2xxx Add SCSI command jammer/discard capability
iscsi-target: graceful disconnect on invalid mapping to iovec
target: need_to_release is always false, remove redundant check and kfree
target: remove sess_kref and ->shutdown_session
iscsi-target: remove usage of ->shutdown_session
tcm_qla2xxx: introduce a private sess_kref
target: make close_session optional
target: make ->shutdown_session optional
target: remove acl_stop
target: consolidate and fix session shutdown
cxgbit: add files for cxgbit.ko
iscsi-target: export symbols
iscsi-target: call complete on conn_logout_comp
iscsi-target: clear tx_thread_active
iscsi-target: add new offload transport type
iscsi-target: use conn_transport->transport_type in text rsp
...
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXIek2AAoJEIaOsuA1yqRE2+cP/iZzzRshn6atj4b0BaRzyk6k
acK6YNs8pBgJMt9FaVWhDOlCfa/8hg5W+6Z5Ovpx4WPyJdZbYkoxJ0ZJGKYjYZ/y
U8hUxpTJ2s2wZKXRKchzT90hQvNlHdg3u2okP2GK0Oa17/idcQf2w1+0Cscm/dqN
Ur5HgukLe31/MrcPr49OuLkahSPfHUQlOn8i4AZyBTh9L8ouzKDCvzUt2ABoCRLE
wPcMegJhks7FQ5fksXtLsfqhqAoHpYHlsZQcH35iV8wPdtSueAtZ8tS6t445XbX9
vEsFq1ovpBMYfl/dwV6RBZiQTjZiGWaIdjOZMUcpbD03yXE2IC6l+mtE/wuhlnHu
J0Rr4YmfS4g++J1+380NQGoreOBZ2u7pujQ4TAy399zsLD8LR3zOQK5IErILSfpO
m6p3ElkGuAyHJKmo4CysSspXnnNGBp/fuTkYdPM9IJRJCe0YwnF/zsQd0OrNZ/Pm
39f6woE2aBQaEzdn+3Nya9B2IWYi6SIheQXPg0HETX/hujZHJv1x758VO6+c7aeq
nlhRlxSe8u8DKryBG43+F+myHaIz1p0Y2O3MzIlvRv0yw87QevJ4pAWptdMITaMh
YpgSjDPw5y2z91AhK/Fv+AXswKaoWBc6EEzBirW6hQWllSp+7qWloA6vYXkdHDr7
QajUBeXzNgXF8JfIos5H
=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.
In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Coccinelle caught this instance of us kfree()ing
devm-allocated memory. The solution is just to not
do anything in our gadget_release.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This function compiles to 298 bytes of machine code, has ~10 callsites.
This is a USB 2.0 device, USB 2.0 is limited to ~40 MB/s, so should be
almost never CPU bound. No need to optimize for speed this agressively.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felipe Balbi <balbi@ti.com>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the following environment, the first argument of DMA API should
be set to a DMAC's device structure, not a udc controller's one.
- A udc controller needs an external DMAC device (like a DMA Engine).
- The external DMAC enables IOMMU.
So, this patch add usb_gadget_{un}map_request_by_dev() API to set
a DMAC's device structure by a udc controller driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort IDs in groups to be easily found when needed.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems there are leftovers of some assignments which are not used
anymore. Compiler even warns us about:
drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]
Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
While here, convert PM ops to use modern API.
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the reserved fields of the SuperSpeed Plus Device Capability
descriptor to 0. Otherwise there might be stale data there which will
cause USB CV to fail.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as they
are "trivial".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJLLUACgkQMUfUDdst+ym3wgCeNSzb74ZskDbGsXUooE0XhYRc
iPoAnRpn/ahoBTzmkKiQXQ1+Br8pAUtN
=vyU/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Since commit 7ace8fc821 ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We added some new locking here, but missed an error path where we need
to unlock.
Fixes: 9acdf4df2f ('usb: gadget: f_midi: added spinlock on transmit function')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Access multi-byte fields of the SSP Dev Cap descriptor using the correct
endianness.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UDC driver should NEVER do anything behind
udc-core's back, so let's stop disabling endpoints
we don't exactly own - rather we provide as
resources for gadget drivers. This fixes the
regression reported by Gil.
Reported-by: Gil Weber <gil.weber@servelec-technologies.com>
Tested-by: Gil Weber <gil.weber@servelec-technologies.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since f_midi_transmit is called by both ALSA and USB sub-systems, it can
potentially cause a race condition between both calls because f_midi_transmit
is not reentrant nor thread-safe. This is due to an implementation detail that
the transmit function looks for the next available usb request from the fifo
and only enqueues it if there is data to send, otherwise just re-uses it. So,
if both ALSA and USB frameworks calls this function at the same time,
kfifo_seek() will return the same usb_request, which will cause a race
condition.
To solve this problem a syncronization mechanism is necessary. In this case it
is used a spinlock since f_midi_transmit is also called by usb_request->complete
callback in interrupt context.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: e1e3d7ec5d ("usb: gadget: f_midi: pre-allocate IN requests")
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't matter
on it's own, but it seems like he is trying to get rid of all CURRENT_TIME
uses in file systems, which is a worthwhile goal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9HqT
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't
matter on it's own, but it seems like he is trying to get rid of all
CURRENT_TIME uses in file systems, which is a worthwhile goal.
* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
configfs: switch ->default groups to a linked list
configfs: Replace CURRENT_TIME by current_fs_time()
Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots of
other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8/EACgkQMUfUDdst+ylsyQCgnVK6ZIFVPV9VijJvBIjxS3F+
fTMAoIMQwNrRMHQOq/lhxX00AgN0B9Ch
=2EQp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots
of other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (266 commits)
USB: core: let USB device know device node
usb: devio: Add ioctl to disallow detaching kernel USB drivers.
usb: gadget: f_acm: Fix configfs attr name
usb: udc: lpc32xx: remove USB PLL and USB OTG clock management
usb: udc: lpc32xx: remove direct access to clock controller registers
usb: udc: lpc32xx: switch to clock prepare/unprepare model
usb: renesas_usbhs: gadget: fix giveback status code in usbhsg_pipe_disable()
usb: gadget: renesas_usb3: Use ARCH_RENESAS
usb: dwc2: Fix issues in dwc2_complete_non_isoc_xfer_ddma()
usb: dwc2: Add support for Lantiq ARX and XRX SoCs
usb: phy: generic: Handle late registration of gadget
usb: gadget: bdc_udc: fix race condition in bdc_udc_exit()
usb: musb: core: added missing const qualifier to musb_hdrc_platform_data::config
usb: dwc2: Move host-specific core functions into hcd.c
usb: dwc2: Move register save and restore functions
usb: dwc2: Use kmem_cache_free()
usb: dwc2: host: If using uframe scheduler, end splits better
usb: dwc2: host: Totally redo the microframe scheduler
usb: dwc2: host: Properly set even/odd frame
usb: dwc2: host: Add dwc2_hcd_get_future_frame_number() call
...
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch drops struct usbg_cmd->kref internal kref-erence
usage, for proper TARGET_SCF_ACK_KREF conversion.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts usb-gadget target to use percpu_ida tag
pre-allocation for struct usbg_cmd descriptor, in order to
avoid fast-path struct usbg_cmd memory allocations.
Note by default this is currently hardcoded to 128.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts existing loopback, usb-gadget, and
xen-scsiback demo-mode only fabric drivers to use the
new target_alloc_session API caller.
This includes adding a new alloc_session callback for
fabric driver internal nexus pointer assignments.
(Fixes for early for-next nexus breakage - Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace the current NULL-terminated array of default groups with a linked
list. This gets rid of lots of nasty code to size and/or dynamically
allocate the array.
While we're at it also provide a conveniant helper to remove the default
groups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Felipe Balbi <balbi@kernel.org> [drivers/usb/gadget]
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Correct attribute name is port_num not num.
Fixes: ea6bd6b ("usb-gadget/f_acm: use per-attribute show and store methods")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
LPC32xx common clock framework driver correctly manages parent clocks
of USB device clock, so there is no need to manually enable and
disable them from the driver, which now depends only on a single USB
device clock.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Direct access to clock control registers can be safely removed, the
task of clock management is done by platform clock driver based on
common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The driver requires to prepare/unprepare clocks to work properly on a
platform with enabled common clock framework, otherwise unprepared
clocks are not enabled:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:728 clk_core_enable+0x2c/0xf0()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #284
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xf0)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_udc_probe+0x284/0x924)
[<>] (lpc32xx_udc_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (__platform_driver_probe+0x54/0x100)
[<>] (__platform_driver_probe) from [<>] (lpc32xx_udc_driver_init+0x1c/0x28)
[<>] (lpc32xx_udc_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
bdc_ep_disable() expects to be called with bdc->lock held.
The assumption is met in all the cases except for call from bdc_udc_exit(),
that is called from bdc_remove(). As a result a race can happen or unheld
bdc->lock can be unlocked in bdc_req_complete().
The patch proposes to acquire-release bdc->lock around bdc_ep_disable()
in bdc_udc_exit().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If gadget with HNP polling support receives GetStatus request of otg
status selector, it feedback to host with host request flag to indicate
if it wants to take host role.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since commit 855ed04a37 ("usb: gadget:
udc-core: independent registration of gadgets and gadget drivers") gadget
drivers can not assume that UDC drivers are already available on their
initialization. This broke the HACK, which was used in gadgetfs driver,
to get UDC controller name. This patch removes this hack and replaces it
by additional function in the UDC core (which is usefully only for legacy
drivers, please don't use it in the new code).
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For every in_substream, there must be a corresponding gmidi_in_port
structure so it is perfectly viable and some might argue sensible to
stash pointer to the input substream in the gmidi_in_port structure.
This has an added benefit that if in_ports < MAX_PORTS, the whole
f_midi structure takes up less space because only in_ports number of
pointers for in_substream are allocated instead of MAX_PORTS lots of
them.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We added a new error path to this function and we forgot to drop the
lock.
Fixes: e1e3d7ec5d ('usb: gadget: f_midi: pre-allocate IN requests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[mina86@mina86.com: rebased on top of refactoring commit]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Reduce number of allocations, simplify memory management and reduce
memory usage by stacking the gmidi_in_port elements at the end of the
f_midi structure using a flexible array.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In general case, all of midi->in_port pointers may be non-NULL which
implies that the ‘if (\!port)’ condition will never execute thus never
zeroing midi->in_last_port. Fix by rewriting the loop such that the
field is set to zero if \!port or end of loop has been reached.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move some of the f_midi_transmit to a separate f_midi_do_transmit
function so the massive indention levels are not so jarring. This
introduces no changes in behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
remove a field which is unnecessary. No functional changes.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ffs_epfile_io and ffs_epfile_io_complete runs in different context, but
there is no synchronization between them.
consider the following scenario:
1) ffs_epfile_io interrupted by sigal while
wait_for_completion_interruptible
2) then ffs_epfile_io set ret to -EINTR
3) just before or during usb_ep_dequeue, the request completed
4) ffs_epfile_io return with -EINTR
In this case, ffs_epfile_io tell caller no transfer success but actually
it may has been done. This break the caller's pipe.
Below script can help test it (adbd is the process which lies on f_fs).
while true
do
pkill -19 adbd #SIGSTOP
pkill -18 adbd #SIGCONT
sleep 0.1
done
To avoid this, just dequeue the request first. After usb_ep_dequeue, the
request must be done or canceled.
With this change, we can ensure no race condition in f_fs driver. But
actually I found some of the udc driver has analogical issue in its
dequeue implementation. For example,
1) the dequeue function hold the controller's lock.
2) before driver request controller to stop transfer, a request
completed.
3) the controller trigger a interrupt, but its irq handler need wait
dequeue function to release the lock.
4) dequeue function give back the request with negative status, and
release lock.
5) irq handler get lock but the request has already been given back.
So, the dequeue implementation should take care of this case. IMO, it
can be done as below steps to dequeue a already started request,
1) request controller to stop transfer on the given ep. HW know the
actual transfer status.
2) after hw stop transfer, driver scan if there are any completed one.
3) if found, process it with real status. if no, the request can
canceled.
Signed-off-by: "Du, Changbin" <changbin.du@intel.com>
[mina86@mina86.com: rebased on top of refactoring commits]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Eliminate one of the return paths by using a ‘goto error_mutex’ and
rearrange some if-bodies which results in reduction of the indention level
and thus hopefully makes the function easier to read and reason about.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In ffs_epfile_io error label points to a return path which includes
a kfree(data) call. However, at the beginning of the function data is
always NULL so some of the early ‘goto error’ can safely be replaced
with a trivial return statement.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the AIO path, if allocating of a request failse, the function simply
goes to the error_lock path whose end result is returning value of ret.
However, at this point ret’s value is zero (assigned as return value from
ffs_mutex_lock).
Fix by adding ‘ret = -ENOMEM’ statement.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the ffs_epfile_io function, data buffer is allocated for non-halt
requests. Later, after grabing a mutex, the function checks that
epfile->ep is still ep and if it’s not, it set ret to -ESHUTDOWN and
follow a path including spin_unlock_irq (just after ‘ret = -ESHUTDOWN’),
mutex_unlock (after if-else-if-else chain) and returns ret. Noticeably,
this does not include freeing of the data buffer.
Fix by introducing a goto which moves control flow to the the end of the
function where spin_unlock_irq, mutex_unlock and kfree are all called.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When I wrote the cleanup patch series, it was not clear how
exactly big-endian mode works on ixp4xx, and whether the driver
was doing this correctly. After discussing with Krzysztof Hałasa,
this has been clarified, so I can update the comment let pxa25x
big-endian (which we don't support) work the same way as ixp4xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB_FSL_MPH_DR_OF symbol is used to ensure the code that interprets
the DR device node is built whenever one of the two drivers (EHCI or
UDC) for the platform is enabled. However, if CONFIG_USB is disabled
and we only support gadget mode, this causes a Kconfig warning:
warning: (USB_FSL_USB2) selects USB_FSL_MPH_DR_OF which has unmet direct dependencies (USB_SUPPORT && USB)
We can avoid this warning by simply no longer using the symbol,
and making sure we enter the drivers/usb/host/ directory when
the UDC driver is enabled that needs the file, and then we use
Makefile syntax to ensure the file is built-in if needed.
There is currently a dependency on CONFIG_OF, but this is redundant,
as we already know that this is set unconditionally for the platforms
that use this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This converts the pxa25x udc driver to use readl/writel as normal
driver should do, rather than dereferencing __iomem pointers
themselves.
Based on the earlier preparation work, we can now also pass
the register start in the device pointer so we no longer need
the global variable.
The unclear part here is for IXP4xx, which supports both big-endian
and little-endian configurations. So far, the driver has done
no byteswap in either case. I suspect that is wrong and it would
actually need to swap in one or the other case, but I don't know
which. It's also possible that there is some magic setting in
the chip that makes the endianess of the MMIO register match the
CPU, and in that case, the code actually does the right thing
for all configurations, both before and after this patch.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This removes the dependency on the mach/hardware.h header file
from the pxa25x_udc driver after the register definitions were
already unified in the previous patch.
Following the model of pxa27x_udc (and basically all other drivers
in the kernel), we define the register numbers as offsets from
the register base address and use accessor functions to read/write
them.
For the moment, this still leaves the direct pointer dereference
in place, instead of using readl/writel, so this patch should
not be changing the behavior of the driver, other than using
ioremap() on the platform resource to replace the hardcoded
virtual address pointers.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ixp4xx and pxa25x both use this driver and provide a slightly
different set of register definitions for it. Aside from that,
the definition in the ixp4xx-regs.h header conflicts with the
on in the pxa27x device driver when compile-testing that:
In file included from ../drivers/usb/gadget/udc/pxa27x_udc.c:37:0:
../drivers/usb/gadget/udc/pxa27x_udc.h:26:0: warning: "UDCCR" redefined
#define UDCCR 0x0000 /* UDC Control Register */
^
In file included from ../arch/arm/mach-ixp4xx/include/mach/hardware.h:27:0,
from ../arch/arm/mach-ixp4xx/include/mach/io.h:18,
from ../arch/arm/include/asm/io.h:194,
from ../include/linux/io.h:25,
from ../include/linux/irq.h:24,
from ../drivers/usb/gadget/udc/pxa27x_udc.c:23:
../arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:415:0: note: this is the location of the previous definition
#define UDCCR IXP4XX_USB_REG(IXP4XX_USB_BASE_VIRT+0x0000)
This addresses both issues by moving all the definitions into the
pxa25x_udc driver itself. It turns out the only difference between
them was 'UDCCS_IO_ROF', and that could well be a mistake when it
was incorrectly copied from pxa25x to ixp4xx.
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable superspeed plus configuration for the mass storage gadget.
The mass storage function doesn't do anything special for
SuperSpeedPlus. Just pass in the same SuperSpeed descriptors for
SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Update the debug message reporting the speeds that a configuration
supports for SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Configure the usb_ep using the SuperSpeedPlus descriptors if connected
in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable writing of SuperSpeedPlus descriptors for any SuperSpeedPlus
capable configuration when connected in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There are a couple places in the code that get the function descriptors
based on the speed. Move this lookup into a function call and add
support to handle the SuperSpeedPlus descriptors as well.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If enumerated in SuperSpeedPlus, count the configurations that support
it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When a function is added to a configuration with usb_add_function(), the
configuration speed flags are updated. These flags indicate for which
speeds the configuration is valid for.
This patch adds a flag in the configuration for SuperSpeedPlus and
also updates this based on the existence of ssp_descriptors.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add a ssp_descriptors member to struct usb_function and handle the
initialization and cleanup of it. This holds the SuperSpeedPlus
descriptors for a function that supports SuperSpeedPlus. This is added
by usb_assign_descriptors().
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the 'ssp_descriptors' parameter to the usb_assign_descriptors()
function. This allows a function driver to add descriptors for
SuperSpeedPlus speeds if it supports it.
Also update all uses of this function in the gadget subsystem so that
they pass NULL for the ssp_descriptors parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a gadget supports SuperSpeedPlus or higher speeds, return a
SuperSpeedPlus USB Device Capability descriptor.
Currently this implementation returns a fixed descriptor with typical
values set.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB 3.1 specification replaces the USB 3.0 specification and all new
devices that are running at SuperSpeed or higher speeds must report a
bcdUSB of 0x0310.
Refer to USB 3.1 Specification, Revision 1.0, Section 9.6.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use regmap to access the PMC to avoid using at91_pmc_read and
at91_pmc_write.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix spelling typos found in printk and Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_remove’:
drivers/usb/gadget/udc/m66592-udc.c:1538:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(m66592->reg);
^
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_probe’:
drivers/usb/gadget/udc/m66592-udc.c:1577:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
reg = ioremap(res->start, resource_size(res));
^
drivers/usb/gadget/udc/m66592-udc.c:1577:6: warning: assignment makes pointer from integer without a cast [enabled by default]
reg = ioremap(res->start, resource_size(res));
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_remove’:
drivers/usb/gadget/udc/net2272.c:2232:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(dev->base_addr);
^
drivers/usb/gadget/udc/net2272.c: In function ‘net2272_plat_probe’:
drivers/usb/gadget/udc/net2272.c:2650:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
dev->base_addr = ioremap_nocache(base, len);
^
drivers/usb/gadget/udc/net2272.c:2650:17: warning: assignment makes pointer from integer without a cast [enabled by default]
dev->base_addr = ioremap_nocache(base, len);
^
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The index variable of list_for_each_entry_safe is an offset from a list
pointer, and thus should not be NULL.
Generated by: scripts/coccinelle/iterators/itnull.cocci
CC: Geliang Tang <geliangtang@163.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Introduce configfs support for unlocked configfs_depend_item()
(krzysztof + andrezej)
- Conversion of usb-gadget target driver to new function registration
interface (andrzej + sebastian)
- Enable qla2xxx FC target mode support for Extended Logins (himansu +
giridhar)
- Enable qla2xxx FC target mode support for Exchange Offload (himansu +
giridhar)
- Add qla2xxx FC target mode irq affinity notification + selective
command queuing. (quinn + himanshu)
- Fix iscsi-target deadlock in se_node_acl configfs deletion (sagi +
nab)
- Convert se_node_acl configfs deletion + se_node_acl->queue_depth to
proper se_session->sess_kref + target_get_session() usage. (hch +
sagi + nab)
- Fix long-standing race between se_node_acl->acl_kref get and
get_initiator_node_acl() lookup. (hch + nab)
- Fix target/user block-size handling, and make sure netlink reaches
all network namespaces (sheng + andy)
Note there is an outstanding bug-fix series for remote I_T nexus port
TMR LUN_RESET has been posted and still being tested, and will likely
become post -rc1 material at this point"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (56 commits)
scsi: qla2xxxx: avoid type mismatch in comparison
target/user: Make sure netlink would reach all network namespaces
target: Obtain se_node_acl->acl_kref during get_initiator_node_acl
target: Convert ACL change queue_depth se_session reference usage
iscsi-target: Fix potential dead-lock during node acl delete
ib_srpt: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Convert acl lookup to modern get_initiator_node_acl usage
tcm_fc: Wait for command completion before freeing a session
target: Fix a memory leak in target_dev_lba_map_store()
target: Support aborting tasks with a 64-bit tag
usb/gadget: Remove set-but-not-used variables
target: Remove an unused variable
target: Fix indentation in target_core_configfs.c
target/user: Allow user to set block size before enabling device
iser-target: Fix non negative ERR_PTR isert_device_get usage
target/fcoe: Add tag support to tcm_fc
qla2xxx: Check for online flag instead of active reset when transmitting responses
qla2xxx: Set all queues to 4k
qla2xxx: Disable ZIO at start time.
qla2xxx: Move atioq to a different lock to reduce lock contention
...
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver
updates and fixes, like usual, and a mix of other USB driver updates as
well. Full details in the shortlog. All of these have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV2rUACgkQMUfUDdst+ym2XQCgqdDOlyGX5B//9CZ2kH1DrDW9
qLsAoLSBvw4hk+Aotv6tn8AayMpHwqV1
=pFLC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB drivers update for 4.5-rc1.
Lots of gadget driver updates and fixes, like usual, and a mix of
other USB driver updates as well. Full details in the shortlog. All
of these have been in linux-next for a while"
* tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits)
MAINTAINERS: change my email address
USB: usbmon: remove assignment from IS_ERR argument
USB: mxu11x0: drop redundant function name from error messages
USB: mxu11x0: fix debug-message typos
USB: mxu11x0: rename usb-serial driver
USB: mxu11x0: fix modem-control handling on B0-transitions
USB: mxu11x0: fix memory leak on firmware download
USB: mxu11x0: fix memory leak in port-probe error path
USB: serial: add Moxa UPORT 11x0 driver
USB: cp210x: add ID for ELV Marble Sound Board 1
usb: chipidea: otg: use usb autosuspend to suspend bus for HNP
usb: chipidea: host: set host to be null after hcd is freed
usb: chipidea: removing of_find_property
usb: chipidea: implement platform shutdown callback
usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference
usb: chipidea: delete static debug support
usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG
usb: chipidea: udc: improve error handling on _hardware_enqueue
usb: chipidea: udc: _ep_queue and _hw_queue cleanup
usb: dwc3: of-simple: fix build warning on !PM
...
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Avoid that building with W=1 triggers compiler warnings about
set-but-not-used variables.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It dose not work when we want to use the usb-to-serial port based
on one usb gadget as a console. Thus this patch adds the console
initialization to support this request.
To avoid the re-entrance when transferring data with usb endpoint,
it introduces a kthread to do the IO transmission.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow using the tcm function as a component of a gadget composed with
ConfigFS.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Do not directly use file static strings definitions in instances of f_tcm.
Instead use usb_gstrings_attach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The only instance is guaranteed with TPG_INSTANCES defined to 1.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no old function interface users left.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Convert the only user of old tcm function interface so that the old
interface can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Converting tcm to the new function interface requires converting
USB tcm's function code and its users.
This patch converts the f_tcm.c to the new function interface.
The file can be now compiled into a separate module usb_f_tcm.ko.
The old function interface is provided by means of preprocessor conditional
directives. After all users are converted, the old interface can be
removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for converting tcm to new function registration interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify function code.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify the function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for splitting tcm_usb_gadget into legacy gadget proper and f_tcm.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Prepare for factoring out f_tcm from a legacy gadget.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up tcm_usbg_tpg_store_enable() return value to propagate
usbg_attach() failure up to user-space if no HDC is found.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing tcm_usbg_drop_nexus() to properly
release tcm_usbg_nexus memory during typical ->fabric_drop_tpg()
callback shutdown.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid stripping off the 'naa.' I_T nexus prefix from configfs
attribute store input, so that user-space will get back what
it originaly wrote into ../usb_gadget/$WWPN/$TPGT/nexus.
Note the SCSI initiator WWPN is purely symbolic for UAS + BOT,
so it will not effect host side code.
Reported-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix bad unlock balance: ep0_write enter with the locks locked from
inode.c:1769, hence it must exit with spinlock held to avoid double
unlock in dev_config.
Signed-off-by: David Eccher <d.eccher@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The gadget ethernet driver supports changing the MTU, but only allows this
when the USB cable is removed. The comment indicates that this is because
the "peer won't know". Even if the network link is still down and only the
USB link is established, the driver won't allow the change.
Other network interfaces allow changing the MTU any time, and don't force
the link to be disabled. This makes perfect sense, because in order to be
able to negotiate the MTU, the link needs to be up.
Remove the restriction so that it is now actually possible to change the
MTU (e.g. using "ifconfig usb0 mtu 15000") without having to manually pull
the plug or change the driver's default setting.
This is especially important after commit bba787a860
("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces pre-allocation of IN endpoint USB requests. This
improves on latency (requires no usb request allocation on transmit) and avoid
several potential probles on allocating too many usb requests (which involves
DMA pool allocation problems).
This implementation also handles better multiple MIDI Gadget ports, always
processing the last processed MIDI substream if the last USB request wasn't
enought to handle the whole stream.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ensures that the midi function will only work if the proper number of
IN and OUT requrests are allocated. Otherwise the function will work with less
requests then what the user wants.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This avoids duplication of USB requests for OUT endpoint and
re-enabling endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes redundant condition.
(!A || (A && B)) is the same as (!A || B).
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change behavior during registration of gadgets and
gadget drivers in udc-core. Instead of previous
approach when for successful probe of usb gadget driver
at least one usb gadget should be already registered
use another one where gadget drivers and gadgets
can be registered in udc-core independently.
Independent registration of gadgets and gadget drivers
is useful for built-in into kernel gadget and gadget
driver case - because it's possible that gadget is
really probed only on late_init stage (due to deferred
probe) whereas gadget driver's probe is silently failed
on module_init stage due to no any UDC added.
Also it is useful for modules case - now there is no
difference what module to insert first: gadget module
or gadget driver one.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
[simplified code as requested by Alan Stern and Felipe Balbi,
fixed checkpatch issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now when last user of usb_udc_attach_driver() is switched
to passing UDC name via usb_gadget_driver struct, it's safe
to remove this function
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now when udc-core supports binding to specific UDC by passing
its name via 'udc_name' member of usb_gadget_driver struct,
switch to this generic approach.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
[rebased and fixed checkpatch issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce new 'udc_name' member to usb_gadget_driver structure.
The 'udc_name' is a name of UDC that usb_gadget_driver should
be bound to. If udc_name is NULL, it will be bound to any
available UDC.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.
Additionally remove other unneeded includes and sort out their order.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since now, we may have more than one request during the test, and
it is better we just quit once the error occurs instead of try
queueing further requests.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since composite now overwrites bcdUSB for any gadget, remove
setting it in legacy gadgets. All legacy gadgets set 0x0200, the
same as the value additionally set by composite, so there is no
behaviour change.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Rebase onto current balbi/next
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary headers and variables.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function is shared between gadget functions, so this avoid unnecessary
duplicated code and potentially avoid memory leaks.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code is duplicated from f_midi_start_ep(midi, f, midi->out_ep).
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add queue depth for both iso and bulk transfer, with more queues, we
can do performance and stress test using sourcesink, and update g_zero
accordingly.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a memory leak that occurs when an endpoint fails to enqueue
the request. If that happens the complete function will never be called, thus
never freeing the request.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes sure f_midi doesn't try to enqueue data when the IN endpoint is
disabled, ie, USB cable is disconnected.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pxa27x disconnects pullups on suspend but doesn't
notify the gadget driver about it, so gadget driver
can't disable the endpoints it was using.
This causes problems on resume because gadget core
will think endpoints are still enabled and just
ignore the following usb_ep_enable().
Fix this problem by calling
gadget_driver->disconnect().
Cc: <stable@vger.kernel.org> # v3.10+
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use safe copy_*_user instead of unsafe __copy_*_user
functions when accessing userland memory.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
1. Rename dequeue_signal_lock() to kernel_dequeue_signal(). This
matches another "for kthreads only" kernel_sigaction() helper.
2. Remove the "tsk" and "mask" arguments, they are always current
and current->blocked. And it is simply wrong if tsk != current.
3. We could also remove the 3rd "siginfo_t *info" arg but it looks
potentially useful. However we can simplify the callers if we
change kernel_dequeue_signal() to accept info => NULL.
4. Remove _irqsave, it is never called from atomic context.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6f64ACgkQMUfUDdst+ykf8gCfYPjtHy5hD/TsharaeXROnVgi
W8cAn16xk1Nmnde220MNNpO6zDu65G/1
=kslf
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Defect 7374 workaround enables all GPEP as endpoint 0. Restore
endpoint number when defect 7374 workaround is disabled. Otherwise,
check to match USB endpoint number to hardware endpoint number in
net2280_enable() fails.
Cc: <stable@vger.kernel.org> # 4.2
Reported-by: Paul Jones <p.jones@teclyn.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit e0857ce58e
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Loopback function is not realy working as that commit removed
all looping back logic. After that commit ep-out works like
/dev/null and ep-in works like /dev/zero.
This commit fix this issue by allocating set of out requests
and set of in requests but each out req shares buffer with
one in req:
out_req->buf ---> buf <--- in_req.buf
out_req->context <---> in_req.context
The completion routine simply enqueue the suitable req in
an oposite direction.
Cc: <stable@vger.kernel.org> # 3.18+
Fixes: e0857ce58e
("usb: gadget: loopback: don't queue requests to bogus endpoints")
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Each instance of loopback function may have different qlen
and buflen attributes values. When linking function to
configuration those values had been assigned to global
variables. Linking other instance to config overwrites those
values.
This commit moves those values to f_loopback structure
to avoid overwriting. Now each function has its own instance
of those values.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move function parameters to struct f_sourcesink to make them per instance
instead of having them as global variables. Since we can have multiple
instances of USB function we also want to have separate set of parameters
for each instance.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This also allows to remove the target-specific old configfs macros, and
gets rid of the target_core_fabric_configfs.h header which only had one
function declaration left that could be moved to a better place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
UVC is a little different from other configfs consumers in that it wants
different function and field names from the exposed attribute name, so
it keeps it's local macros to define attributes instead of using the common
ones.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To simplify the configfs interface and remove boilerplate code that also
causes binary bloat.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When handling device GET_DESCRIPTOR, composite gadget driver fills
the bcdUSB field only if the gadget supports USB 3.0. Otherwise
the field is left unfilled.
For consistency, set bcdUSB to 0x0200 for gadgets that don't
support superspeed.
It's correct to use 0x0200 for any setting that doesn't use
superspeed, since USB 2.0 devices can restrict themselves to
full speed only. It is NOT correct to use 0x0210, since BOS
descriptors are handled only if gadget_is_superspeed() is
satisfied, otherwise it results in a stall.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most of USB functions place new line after attribute value.
Let's follow this convention also in source sink function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most of USB functions place new line after attribute value.
Let's follow this convention also in loopback function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While building allmodconfig on avr32 the build failed with the error:
"at91_pmc_base" [drivers/usb/gadget/udc/atmel_usba_udc.ko] undefined!
On checking the code it turned out that if CONFIG_OF is defined then it
is using at91_pmc_read() which is using at91_pmc_base. And unless
COMMON_CLK_AT91 is defined we donot have at91_pmc_base. And
COMMON_CLK_AT91 is available with AT91 architecture.
Mention the dependency such that this driver builds with avr32 only if
OF is not enabled.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A NULL comparison can be written as if (var) or if (!var).
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_basic_init function to remove the forward declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the forward declarations of udc_pci_probe and udc_pci_remove.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange udc_free_dma_chain to remove the forward declaration. While at
it fixed all the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange udc_create_dma_chain to remove the forward declaration. While
rearranging fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_remote_wakeup function to remove the forward
declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_probe function to remove the forward declarations.
While rearranging also fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The condition checking for irq_registered, regs, mem_region and active
are not required as this is the remove function. And we are in the
remove means that probe was successful and they can never be NULL at
this point of code.
It was required in the original code as the remove function was part of
the error handler of probe function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have the function free_dma_pools() which frees all the dma pools. Use
it instead of calling all the functions separately. The if conditions
for data_requests and stp_requests are also not required here as this is
the remove function and we are here means probe has succeeded and dma
has been successfully allocated, so they cannot be NULL here.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use WARN_ON() instead of halting the kernel with BUG_ON() and also fix
the checkpatch warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle the error properly instead of calling the pci remove function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A rewrite of init_dma_pools() with proper error handling.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If dma_pool_alloc() fails we are jumping to fail and releasing all the
bd_tables which have been added to the chain but we missed freeing this
bd_table which was just allocated and still not added to the chain of
bd_table.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
gadget methods should be called without
spinlocks held.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of tcm, ep->driver_data was used only for endpoint claiming so
we can simplify code by reducing it. We also remove give_back_ep()
function which is not needed after all - when error code is returned
from bind() function, composite will release all endpoints anyway.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of dbgp, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of u_serial ep->driver_data stores pointer to struct gs_port,
which is referenced in many places in code. Code using ep->driver_data
to mark endpoint as enabled/disabled has been removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of u_ether we only need to store in ep->driver_data pointer to
struct eth_dev, as it's used in rx_complete() and tx_complete() callbacks.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uvc, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uac2, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uac1, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_subset, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_sourcesink we only need to store in ep->driver_data pointer
to struct f_sourcesink, as it's used in source_sink_complete() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_serial, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_rndis, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_printer we only need to store in ep->driver_data pointer to
struct printer_dev, as it's used in rx_complete() and tx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_phonet we only need to store in ep->driver_data pointer to
struct f_phonet, as it's used in pn_tx_complete() and pn_rx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_obex, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ncm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_midi we only need to store in ep->driver_data pointer to
struct f_midi, as it's used in f_midi_complete() callback and related
functions. All other uses of ep->driver_data are now meaningless and
can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_mass_storage we only need to store in ep->driver_data
pointer to struct fsg_common, which is used in bulk_in_complete() and
bulk_out_complete() callbacks. All other uses of ep->driver_data are now
meaningless and can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_loopback, as it's used in loopback_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_hidg, as it's used in f_hidg_req_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_acm we only need to store in ep->driver_data pointer to
struct f_acm, as it's used in acm_complete_set_line_coding() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces usb_ep_autoconfig_release() function which allows
to release endpoint previously obtained from usb_ep_autoconfig() during
USB function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 'driver_data' field in ep0 is never set to pointer to cdev, so we
have to obtain it from another source as in this context ep->driver_data
contains invalid data.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix comments in code to make them up to date.
composite: claiming endpoint is now done by setting ep->claimed flag,
not ep->driver_data.
epautoconf: usb_ep_autoconfig() and usb_ep_autoconfig_ss() return
claimed endpoint with ep->claimed flag already set.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The millisecond of the last second will be normal if tv_sec is
overflowed. But for y2038 consistency and demonstration purpose,
and avoiding further risks, we need to remove 'timeval' in this
driver, to avoid similair problems.
Signed-off-by: Pingbo Wen <pingbo.wen@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the host and gadget can't agree with transfer length before
each transfer, but they agree with max packet size for each
endpoint, we use max packet size to format data pattern.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB network adapters support Jumbo frames. The only thing blocking
that feature is the code in the gadget driver that disposes of
packets larger than 1518 bytes, and the limit on the ioctl to set
the mtu.
This patch relaxes these limits, and allows up to 15k frames sizes.
The 15k value was chosen because 16k does not work on all platforms,
and usingclose to 16k will result in allocating 5 or 8 4k pages to
store the skb, wasting pages at no measurable performance gain.
On a topic-miami board (Zynq-7000), iperf3 performance reports:
MTU= 1500, PC-to-gadget: 139 Mbps, Gadget-to-PC: 116 Mbps
MTU=15000, PC-to-gadget: 239 Mbps, Gadget-to-PC: 361 Mbps
On boards with slower CPUs the performance improvement will be
relatively much larger, e.g. an OMAP-L138 increased from 40 to
220 Mbps using a similar patch on an 2.6.37 kernel.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct at91_udc_data is now only used inside the driver, move it to its
include.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_midi is not checking whether there is an error on usb_ep_queue
request, ignoring potential problems, such as memory leaks.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of allowing a range of 2 to 4 requests,
let's allow the user choose up to 32 requests
as that will give us a better chance of keeping
controller busy.
We still maintain default of 2 so users shouldn't
be affected.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dummy_timer uses transfer() to update transfer limit. However,
limit passed to dummy_timer changes depending on transfer type,
so the actual limit is overwritten.
This can cause unpredictably slow / fast bulk transfers when
coupled with control / interrupt transfers.
Fix by returning actual amount of data sent in transfer() and
substracting from total.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
transfer() schedules a rescan for transfers larger than
maxpacket, which is wrong for transfers that are multiples
of maxpacket.
Rewrite to fix and clarify packet multiple / remainder
transfer logic.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already know at this point that to_host is false.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
currently, when a zlp flag is set and an urb/usb_request
buffer is filled without a short packet, transfer() leaves
its status at -EINPROGRESS and does not rescan for short
packet.
In a scenario where ep.maxpacket bytes are copied,
URB_ZERO_PACKET is set, urb buffer is filled and usb_request
buffer is not, transfer() returns with an urb with
-EINPROGRESS status, which dummy_hcd treats as incomplete
transfer.
Check for zlp and rescan appropriately.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The recently added endpoint capabilities flags verification breaks Atmel
USBA because the endpoint configuration was only added when the driver
is bound using the legacy pdata interface.
Convert endpoint configuration to new capabilities model when driver is
bound to a device tree as well.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Fixes: 47bef38651 ("usb: gadget: atmel_usba_udc: add ep capabilities support")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a failure happens early in udc_pci_probe(), error handling code
just kfree(dev) and returns. The patch adds proper resource
deallocations in udc_pci_probe() itself,
since udc_pci_remove() is not suitabe to be called so early
in initialization process.
By the way, iounmap(dev->regs) is replaced by iounmap(dev->virt_addr)
in udc_pci_remove() for clarity.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes possible regression introduced by
patch reworking endpoint claiming mechanism. It restores
setring ep->driver_data to NULL in usb_ep_autoconfig_reset(),
which was removed by patch commit cc476b42a3.
Fixes: cc476b42a3 ("usb: gadget: encapsulate endpoint
claiming mechanism")
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WuIB
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
<linux/uaccess.h> was originally being pulled
indirectly through some other header, however
it's not anymore, so we need to include it
directly
Reported-by: Jim Davis <jim.epost@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This header file contains helpers for quirks based on UDC controller name.
Since we have generic quirk bitfields in usb_gadget structure for all of
these quirks we don't need to have this header any longer.
This patch removes gadget_chips.h file and makes sure that it's no longer
included anywhere in kernel sources.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
[ balbi@ti.com : fix build breakage ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add 'match_ep' callback to utilize chip-specific knowledge in endpoint matching
process. Function does the same that was done by chip-specific code inside
of epautoconf. Now this code can be removed from there to separate generic code
from platform specific logic.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move find_ep() to udc-core and rename it to gadget_find_ep_by_name().
It can be used in UDC drivers, especially in 'match_ep' callback after
moving chip-specific endpoint matching logic from epautoconf to UDC
drivers.
Replace all calls of find_ep() function with gadget_find_ep_by_name().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move ep_matches() function to udc-core and rename it to
usb_gadget_ep_match_desc(). This function can be used by UDC drivers
in 'match_ep' callback to avoid writing lots of repetitive code.
Replace all calls of ep_matches() with usb_gadget_ep_match_desc().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add callback that is called by epautoconf to allow UDC driver match the
best endpoint for specific descriptor. It's intended to supply mechanism
which allows to get rid of chip-specific endpoint matching code from
epautoconf.
If gadget has set 'ep_match' callback we prefer to call it first, and
if it fails to find matching endpoint, then we try to use default matching
algorithm.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rework ep_matches() function to make it shorter and more readable.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As function ep_matches() is used to match endpoint with usb descriptor it's
highly unintuitive that it modifies endpoint and descriptor structures fields.
This patch moves code configuring ep and desc from ep_matches() to
usb_ep_autoconfig_ss(), so now function ep_matches() does nothing more than
its name suggests.
[ balbi@ti.com : fix build warning ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The same effect can be achieved by using capabilities flags, so now we can
get rid of handling of hardware specific limitations in generic code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce endpoint matching mechanism basing on endpoint capabilities
flags. We check if endpoint supports transfer type and direction requested
in ep descriptor. Since we have this new endpoint matching mechanism
there is no need to have old code guessing endpoint capabilities basing
on its name, so we are getting rid of it. Remove also the obsolete comment.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far it was necessary for usb functions to set ep->driver_data in
endpoint obtained from autoconfig to non-null value, to indicate that
endpoint is claimed by function (in autoconfig it was checked if endpoint
has set this field to non-null value, and if it has, it was assumed that
it is claimed). It could cause bugs because if some function doesn't
set this field autoconfig could return the same endpoint more than one
time.
To help to avoid such bugs this patch adds claimed flag to struct usb_ep,
and encapsulates endpoint claiming mechanism inside usb_ep_autoconfig_ss()
and usb_ep_autoconfig_reset(), so now usb functions don't need to perform
any additional actions to mark endpoint obtained from autoconfig as claimed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 913e4a90b6 ("usb: gadget: f_uac2:
finalize wMaxPacketSize according to bandwidth")
added a possible build warning when calling
min(). In order to fix the warning, we just
make sure to call min_t() and tell that its
arguments should be u16.
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a bug in the error pathway of
usb_add_gadget_udc_release() in udc-core.c. If the udc registration
fails, the gadget registration is not fully undone; there's a
put_device(&gadget->dev) call but no device_del().
CC: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function printer_func_disable() has called spinlock on printer_dev->lock,
and it'll call function chain of
printer_reset_interface()
|
+---dwc3_gadget_ep_disable()
|
+---__dwc3_gadget_ep_disable()
|
+---dwc3_remove_requests()
|
+---dwc3_gadget_giveback()
|
+---rx_complete()
in the protected block.
However, rx_complete() in f_printer.c calls spinlock on printer_dev->lock
again, which will cause system hang.
The following steps can reproduce this hang:
1. Build the test program from Documentation/usb/gadget_printer.txt as
g_printer
2. Plug in the USB device to a host(such as Ubuntu).
3. on the USB device system run:
#modprobe g_printer.ko
#./g_printer -read_data
4. Unplug the USB device from the host
The system will hang later.
In order to avoid this deadlock, moving the spinlock from
printer_func_disable() into printer_reset_interface() and excluding the block
of calling dwc3_gadget_ep_disable(), in which the critical resource will be
protected by its spinlock in rx_complete().
This commit will fix the system hang with the following calltrace:
INFO: rcu_preempt detected stalls on CPUs/tasks: { 3} (detected by 0, t=21006 jiffies, g=524, c=523, q=2)
sending NMI to all CPUs:
NMI backtrace for cpu 3
CPU: 3 PID: 718 Comm: irq/22-dwc3 Not tainted 3.10.38-ltsi-WR6.0.0.11_standard #2
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS BYTICRB1.86C.0092.R32.1410021707 10/02/2014
task: f44f4c20 ti: f40f6000 task.ti: f40f6000
EIP: 0060:[<c1824955>] EFLAGS: 00000097 CPU: 3
EIP is at _raw_spin_lock_irqsave+0x35/0x40
EAX: 00000076 EBX: f80fad00 ECX: 00000076 EDX: 00000075
ESI: 00000096 EDI: ffffff94 EBP: f40f7e20 ESP: f40f7e18
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: b77ac000 CR3: 01c30000 CR4: 001007f0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
f474a720 f80fad00 f40f7e3c f80f93cc c135d486 00000000 f474a720 f468fb00
f4bea894 f40f7e54 f7e35f19 ffffff00 f468fb00 f468fb24 00000086 f40f7e64
f7e36577 f468fb00 f4bea810 f40f7e74 f7e365a8 f468fb00 f4bea894 f40f7e9c
Call Trace:
[<f80f93cc>] rx_complete+0x1c/0xb0 [g_printer]
[<c135d486>] ? vsnprintf+0x166/0x390
[<f7e35f19>] dwc3_gadget_giveback+0xc9/0xf0 [dwc3]
[<f7e36577>] dwc3_remove_requests+0x57/0x70 [dwc3]
[<f7e365a8>] __dwc3_gadget_ep_disable+0x18/0x60 [dwc3]
[<f7e366e9>] dwc3_gadget_ep_disable+0x89/0xf0 [dwc3]
[<f80f9031>] printer_reset_interface+0x31/0x50 [g_printer]
[<f80f9270>] printer_func_disable+0x20/0x30 [g_printer]
[<f80e6d8b>] composite_disconnect+0x4b/0x90 [libcomposite]
[<f7e39a8b>] dwc3_disconnect_gadget+0x38/0x43 [dwc3]
[<f7e39ad4>] dwc3_gadget_disconnect_interrupt+0x3e/0x5a [dwc3]
[<f7e373b8>] dwc3_thread_interrupt+0x5c8/0x610 [dwc3]
[<c10ac518>] irq_thread_fn+0x18/0x30
[<c10ac800>] irq_thread+0x100/0x130
[<c10ac500>] ? irq_finalize_oneshot.part.29+0xb0/0xb0
[<c10ac650>] ? wake_threads_waitq+0x40/0x40
[<c10ac700>] ? irq_thread_dtor+0xb0/0xb0
[<c1057224>] kthread+0x94/0xa0
[<c182b337>] ret_from_kernel_thread+0x1b/0x28
[<c1057190>] ? kthread_create_on_node+0xc0/0xc0
Signed-off-by: Fupan Li <fupan.li@windriver.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch replace dynamicly allocated luns array with static one.
This simplifies the code of mass storage function and modules.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Add missing return value check. In case of error print debug message
and return error code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function midi registers two interfaces with single set_alt() function
which means that f_midi_set_alt() is called twice when configuration
is set. That means that endpoint initialization and ep request allocation
is done two times. To avoid this problem we do such things only once,
for interface number 1 (MIDI Streaming interface).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function ffs_do_functionfs_bind() calls functionfs_bind() which allocates
usb request and increments refcounts. These things needs to be cleaned
up by if further steps of initialization fail by calling functionfs_unbind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to USB Audio Device 2.0 Spec, Ch4.10.1.1:
wMaxPacketSize is defined as follows:
Maximum packet size this endpoint is capable of sending or receiving
when this configuration is selected.
This is determined by the audio bandwidth constraints of the endpoint.
In current code, the wMaxPacketSize is defined as the maximum packet size
for ISO endpoint, and it will let the host reserve much more space than
it really needs, so that we can't let more endpoints work together at
one frame.
We find this issue when we try to let 4 f_uac2 gadgets work together [1]
at FS connection.
[1]http://www.spinics.net/lists/linux-usb/msg123478.html
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: andrzej.p@samsung.com
Cc: Daniel Mack <zonque@gmail.com>
Cc: tiwai@suse.de
Cc: <stable@vger.kernel.org> #v3.18+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the worker thread is launched, bind function is doing further
configuration. In case of failure stop the thread.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sanjay Singh Rawat <snjsrwt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is an "&&" vs "||" typo here so this loops 3000 times or if we get
unlucky it could loop forever.
Fixes: ceaa0a6eea ('usb: gadget: m66592-udc: add support for TEST_MODE')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We handle the "if (!req->req.length)" condition at the start of the
function and return. We can delete this dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace calls of gadget_supports_altsettings() function (which check altset
support by comparing UDC controller name with hardcoded names) with
gadget_is_altset_supported() which checks generic quirk bitfield.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports zlp.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use generic mechanism to check if UDC controller supports stalling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support stalling, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_stall_not_supp' field to struct usb_gadget and helper
function gadget_is_stall_supported(). It also sets 'quirk_stall_not_supp'
to 1 in at91_udc driver, which has such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to some UDC controllers may not support altsettings, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_altset_not_supp' field to struct usb_gadget and helper
function gadget_is_altset_supported(). It also sets 'quirk_altset_not_supp'
to 1 in pxa25x_udc and pxa27x_udc drivers, which have such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().
When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.
For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Creation of LUN 0 may fail (for example due to ENOMEM).
As fsg_common_set_num_buffers() does some memory allocation
we should free it before it becomes unavailable.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Currently this parameter is made optional with the help of a cpp trick.
To allow dropping this hack convert callers to explictly pass a value
for flags.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, the macro cpu_to_le{16,32} unfolds to __swab{16,32}
which provides special case for constants. In little endian cases,
__constant_cpu_to_le{16,32} and cpu_to_le{16,32} expand directly to
the same expression. So, replace __constant_cpu_to_le{16,32} with
cpu_to_le{16,32} with the goal of getting rid of the definition of
__constant_cpu_to_le{16,32} completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
(
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
|
- __constant_cpu_to_le32(x)
+ cpu_to_le32(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I18N should be spelled as i18n because it's not
an acronym
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As SourceSink function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As loopback function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds removable mass storage support to g_nokia gadget (for N900).
It means that at runtime block device can be exported or unexported.
So it does not export anything by default and thus allows to use MyDocs
partition as before...
[ balbi@ti.com: make it build ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a predefined maximum number of printer instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many printer function directories as they like. To make the
number of printer instances consistent with the number of allocated
minors, the limit is enforced at directory creation time.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a predefined maximum number of hid instances, currently 4.
A chrdev region is allocated accordingly, but with configfs the user
can create as many hid function directories as they like. To make
the number of hid instances consistent with the number of allocated minors,
the limit is enforced at directory creation time.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The p_interval should be less if the 'bInterval' at the descriptor
is larger, eg, if 'bInterval' is 5 for HS, the p_interval should be
8000 / 16 = 500.
It fixes the patch 9bb87f1689 ("usb: gadget: f_uac2: send
reasonably sized packets")
Cc: <stable@vger.kernel.org> # v3.18+
Fixes: 9bb87f1689 ("usb: gadget: f_uac2: send reasonably sized packets")
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep_dequeue() in bdc_ep.c was capturing the hw dequeue pointer
incorrectly by reading the wrong register for the upper 32 bits.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some modules call config_item_init_type_name() and config_group_init_type_name()
with parameter "name" directly controlled by userspace. These two
functions call config_item_set_name() with this name used as a format
string, which can be used to leak information such as content of the
stack to userspace.
For example, make_netconsole_target() in netconsole module calls
config_item_init_type_name() with the name of a newly-created directory.
This means that the following commands give some unexpected output, with
configfs mounted in /sys/kernel/config/ and on a system with a
configured eth0 ethernet interface:
# modprobe netconsole
# mkdir /sys/kernel/config/netconsole/target_%lx
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# echo 1 > /sys/kernel/config/netconsole/target_%lx/enabled
# echo eth0 > /sys/kernel/config/netconsole/target_%lx/dev_name
# dmesg |tail -n1
[ 142.697668] netconsole: target (target_ffffffffc0ae8080) is
enabled, disable to update parameters
The directory name is correct but %lx has been interpreted in the
internal item name, displayed here in the error message used by
store_dev_name() in drivers/net/netconsole.c.
To fix this, update every caller of config_item_set_name to use "%s"
when operating on untrusted input.
This issue was found using -Wformat-security gcc flag, once a __printf
attribute has been added to config_item_set_name().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case kstrdup() fails the resources to release are
midi->in_port[] and midi. No cards have been registered,
so no need to unregister any.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
My static checker detected the mistake. I fix this by changing "goto
err_irq" to "goto err_req". The label err_irq is not used now
so this patch also removes it.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f563d23090 ("usb: gadget: composite: add req_match method
to usb_function") accesses cdev->config even before set config
is invoked causing a NULL pointer dereferencing error while running
Lecroy Mass Storage Compliance test.
Fix it here by accessing cdev->config only if it is non NULL.
Fixes: commit f563d23090 ("usb: gadget: composite: add req_match
method to usb_function").
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
do not try to set cancel function in synchronous operations in
ffs_epfile_{read,write}_iter.
Cc: <stable@vger.kernel.org> # v4.0+
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage function created via configfs always reports eight LUNs
to the hosts even if only one LUN has been configured. Adjust the
number when the USB function is allocated based on LUNs that user
has created.
Cc: <stable@vger.kernel.org>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.
Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.
Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
By always allocating and adding, respectively removing and freeing
the se_node_acl structure in core code we can remove tons of repeated
code in the init_nodeacl and drop_nodeacl routines. Additionally
this now respects the get_default_queue_depth method in this code
path as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All fabric drivers except for iSCSI always return 1, so implement
that as default behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Except for the embedded struct se_node_acl none of the fields were
ever used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the following build warnings:
drivers/usb/gadget/udc/atmel_usba_udc.c:2207:12: warning:
‘usba_udc_suspend’ defined but not used [-Wunused-function] static int
usba_udc_suspend(struct device *dev)
drivers/usb/gadget/udc/atmel_usba_udc.c:2236:12: warning:
‘usba_udc_resume’ defined but not used [-Wunused-function] static int
usba_udc_resume(struct device *dev)
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following build warning:
drivers/usb/gadget/udc/atmel_usba_udc.c:707:2: warning: format ‘%x’
expects argument of type ‘unsigned int’, but argument 4 has type
‘dma_addr_t’ [-Wformat=]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is removed.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reset configuration in ep_cfg on disable to physically disable the
endpoint.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 GPEP can be used in IN and OUT directions however, both
directions should use same endpoint address. Fulfil this requirement
by mapping usb endpoint to hardware endpoint with the same address.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 enhanced mode allows GPEP to be used in both IN and OUT
directions. However, IN and OUT endpoints must use same USB endpoint
address (bEndpointAddress). Fix this by setting the ep_cfg.ep_number
during initialization and keep it in net2280_enable()
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 in enhanced mode has 4 IN and 4 OUT endpoints. Check
interrupts for all of them.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Default 0 value can result in unintentional zlp for IN endpoints.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB3380 ep_cfg.direction bit is reserved in enhanced mode. Don't set
it.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If ep->dma is set, abort_dma() takes care of dma clean-up. If ep->dma
is not set, unconditionally reset dma channel.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sequence number can be out of sync if endpoint is disabled after some
data transfers and enabled again. Reset it to stay in sync with host.
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_closed can race with configfs_rmdir which will call config_item_release, so
add an extra check to avoid calling the unregister_gadget_item with an null
gadget item.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
when copying to iter the size can be different then the iov count,
the check for full iov is wrong and make any read on request which
is not the exactly size of iov to return -EFAULT.
So, just check the success of the copy.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not checking config_ep_by_speed could lead to a kernel
NULL pointer dereference error in usb_ep_enable
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Originally FFS_FL_CALL_CLOSED_CALLBACK flag has been used to
indicate if we should call ffs_closed_callback().
Commit 4b187fceec ("usb: gadget: FunctionFS: add devices
management code") changed its semantic to indicate if we should
call ffs_closed() function which does a little bit more.
This situation leads to:
[ 122.362269] ------------[ cut here ]------------
[ 122.362287] WARNING: CPU: 2 PID: 2384 at drivers/usb/gadget/function/f_fs.c:3417 ffs_ep0_write+0x730/0x810 [usb_f_fs]()
[ 122.362292] Modules linked in:
[ 122.362555] CPU: 2 PID: 2384 Comm: adbd Tainted: G W 4.1.0-0.rc4.git0.1.1.fc22.i686 #1
[ 122.362561] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/25/2014
[ 122.362567] c0d1f947 415badfa 00000000 d1029e64 c0a86e54 00000000 d1029e94 c045b937
[ 122.362584] c0c37f94 00000002 00000950 f9b313d4 00000d59 f9b2ebf0 f9b2ebf0 fffffff0
[ 122.362600] 00000003 deb53d00 d1029ea4 c045ba42 00000009 00000000 d1029f08 f9b2ebf0
[ 122.362617] Call Trace:
[ 122.362633] [<c0a86e54>] dump_stack+0x41/0x52
[ 122.362645] [<c045b937>] warn_slowpath_common+0x87/0xc0
[ 122.362658] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362668] [<f9b2ebf0>] ? ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362678] [<c045ba42>] warn_slowpath_null+0x22/0x30
[ 122.362689] [<f9b2ebf0>] ffs_ep0_write+0x730/0x810 [usb_f_fs]
[ 122.362702] [<f9b2e4c0>] ? ffs_ep0_read+0x380/0x380 [usb_f_fs]
[ 122.362712] [<c05a1c1f>] __vfs_write+0x2f/0x100
[ 122.362722] [<c05a42f2>] ? __sb_start_write+0x52/0x110
[ 122.362731] [<c05a2534>] vfs_write+0x94/0x1b0
[ 122.362740] [<c0a8a1c0>] ? mutex_lock+0x10/0x30
[ 122.362749] [<c05a2f41>] SyS_write+0x51/0xb0
[ 122.362759] [<c0a8c71f>] sysenter_do_call+0x12/0x12
[ 122.362766] ---[ end trace 0673d3467cecf8db ]---
in some cases (reproduction path below). This commit get back
semantic of that flag and ensures that ffs_closed() is called
always when needed but ffs_closed_callback() is called only
if this flag is set.
Reproduction path:
Compile kernel without any UDC driver or bound some gadget
to existing one and then:
$ modprobe g_ffs
$ mount none -t functionfs mount_point
$ ffs-example mount_point
This will fail with -ENODEV as there is no udc.
$ ffs-example mount_point
This will fail with -EBUSY because ffs_data has not been
properly cleaned up.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Returning non-zero value from ready callback makes ffs instance
return error from writing strings and enter FFS_CLOSING state.
This means that this this function is not truly ready and
close callback will not be called. This commit fix
ffs_ready_callback() to undo all side effects of this function
in case of error.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For some reason the code has always been disabling pullup
when asked to do the opposite. According to surrounding code
and gadget API this seems to be a mistake. This fix allows
UDC to be detected by host controller on recent kernels.
Signed-off-by: Sergiy Kibrik <sakib@meta.ua>
Signed-off-by: Felipe Balbi <balbi@ti.com>
rndis_get_nr() returns either a non-negative value on success
or a negative value on failure. In case of failure an error code
is returned to the caller of rndis_register().
If the "i" is unsigned, the information about error from rndis_get_nr()
is lost. If there is no error but rndis_get_nr() returns a value greater
than 256 the least significant bits of i are zero effectively limiting the
number of configs to 256.
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If CONFIG_USB_GADGET_DEBUG_FILES is set then a block is opened and inside
it there is a local variable "i" which hides the "i" local to the
rndis_deregister(). Consequently, a random value is formatted
into the "name" buffer.
This patch removes the block-local i.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch:
83210e59ee
usb: gadget: rndis: use rndis_params instead of configNr
should change all invocations of rndis_signal_(dis)connect().
This patch fixes that.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We should not be doing assignments within an if () block
so fix up the code to not do this.
change was created using Coccinelle.
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
CC: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch allocates struct rndis_params on demand in rndis_register().
Coversly, the structure is free()'d in rndis_deregister().
If CONFIG_USB_GADGET_DEBUG_FILES is set, the proc files are created which
is the same behaviour as before, but the moment of creation is delayed
until struct rndis_params is actually allocated.
rnids_init() and rndis_exit() have nothing to do, so they are eliminated.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use a space between function name and parameter list opening bracket.
All other functions in this file comply wich checkpatch rules.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
RNDIS function has a limitation on the number of allowed instances.
So far it has been RNDIS_MAX_CONFIGS, which happens to be one.
In order to eliminate this kind of arbitrary limitation we should not
preallocate a predefined (RNDIS_MAX_CONFIGS) array of struct rndis_params
instances but instead allow allocating them on demand.
This patch prepares the elimination of the said limit by converting all the
functions which accept rndis config number to accept a pointer to the
actual struct rndis_params. Consequently, rndis_register() returns
a pointer to a corresponding struct rndis_params instance. The pointer
is then always used by f_rndis.c instead of config number when it talks
to rndis.c API.
A nice side-effect of the changes is that many lines of code in rndis.c
become shorter and fit in 80 columns.
If a function prototype changes in rndis.h a style cleanup is made
at the same time, otherwise checkpatch complains that the patch
has style problems.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using unnecessary static char buffers isn't good.
Use the %pV extension instead.
Miscellanea:
o the dprintk return value is unused, make it void
o add __printf format and argument verification
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a single thread is sending out data over the gadget serial port,
gs_start_tx() will be called both from the sender context and from the
write completion. Since the port lock is released before the packet is
queued, the order in which the URBs are submitted is not guaranteed.
E.g.
sending thread completion (interrupt)
gs_write()
LOCK
gs_write_complete()
LOCK (wait)
gs_start_tx()
req1 = list_entry(pool->next)
UNLOCK
LOCK (acquired)
gs_start_tx()
req2 = list_entry(pool->next)
UNLOCK
usb_ep_queue(req2)
usb_ep_queue(req1)
I.e., req2 is submitted before req1 but it contains the data that
comes after req1.
To reproduce, use SMP with sending thread and completion pinned to
different CPUs, or use PREEMPT_RT, and add the following delay just
before the call to usb_ep_queue():
if (port->write_started > 0 && !list_empty(pool))
udelay(1000);
To work around this problem, make sure that only one thread is running
through the gs_start_tx() loop with an extra flag write_busy. Since
gs_start_tx() is always called with the port lock held, no further
synchronisation is needed. The original caller will continue through
the loop when the request was successfully submitted.
Signed-off-by: Philip Oberstaller <Philip.Oberstaller@septentrio.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have multiple instances of hid function, each of
them may have different report descriptor, also their
length may be different.
Currently we are using static hidg_desc varable which
is being filled in hidg_bind(). Then we send its content
to host in hidg_setup() function. This content may
have been already overwriten if another instance
has executed hidg_bind().
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never
returns NULL, fix the check to prevent access to invalid
virtual address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
Pull second vfs update from Al Viro:
"Now that net-next went in... Here's the next big chunk - killing
->aio_read() and ->aio_write().
There'll be one more pile today (direct_IO changes and
generic_write_checks() cleanups/fixes), but I'd prefer to keep that
one separate"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
->aio_read and ->aio_write removed
pcm: another weird API abuse
infinibad: weird APIs switched to ->write_iter()
kill do_sync_read/do_sync_write
fuse: use iov_iter_get_pages() for non-splice path
fuse: switch to ->read_iter/->write_iter
switch drivers/char/mem.c to ->read_iter/->write_iter
make new_sync_{read,write}() static
coredump: accept any write method
switch /dev/loop to vfs_iter_write()
serial2002: switch to __vfs_read/__vfs_write
ashmem: use __vfs_read()
export __vfs_read()
autofs: switch to __vfs_write()
new helper: __vfs_write()
switch hugetlbfs to ->read_iter()
coda: switch to ->read_iter/->write_iter
ncpfs: switch to ->read_iter/->write_iter
net/9p: remove (now-)unused helpers
p9_client_attach(): set fid->uid correctly
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All places outside of core VFS that checked ->read and ->write for being NULL or
called the methods directly are gone now, so NULL {read,write} with non-NULL
{read,write}_iter will do the right thing in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix using the bare numbers to set the 'bDescriptorType' field of the Hub
Descriptors while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct kiocb now is a generic I/O container, so move it to fs.h.
Also do a #include diet for aio.h while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If f_printer is selected without legacy g_printer, it should
depend on USB_CONFIGFS which pulls in libcomposite.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's a number of USB and PHY driver fixes for 4.0-rc5. Largest thing
here is a revert of a gadget function driver patch that removes 500
lines of code. Other than that, it's a number of reported bugs fixes
and new quirk/id entries.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUOmk4ACgkQMUfUDdst+ym94wCdGs4iVQbrTA9p+561H8jhCCxh
79oAn3y24kql3ob9/iuV6+N36+HQsp+0
=IPei
-----END PGP SIGNATURE-----
Merge tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here's a number of USB and PHY driver fixes for 4.0-rc5.
The largest thing here is a revert of a gadget function driver patch
that removes 500 lines of code. Other than that, it's a number of
reported bugs fixes and new quirk/id entries.
All have been in linux-next for a while"
* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: common: otg-fsm: only signal connect after switching to peripheral
uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
USB: ehci-atmel: rework clk handling
MAINTAINERS: add entry for USB OTG FSM
usb: chipidea: otg: add a_alt_hnp_support response for B device
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
phy: ti/omap: Fix modalias
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
phy: Find the right match in devm_phy_destroy()
phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
phy: samsung-usb2: Remove NULL terminating entry from phys array
phy: hix5hd2-sata: Check return value of platform_get_resource
phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
Revert "usb: gadget: zero: Add support for interrupt EP"
Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
...
Pull SCSI target fixes from Nicholas Bellinger:
"Here are current target-pending fixes for v4.0-rc5 code that have made
their way into the queue over the last weeks.
The fixes this round include:
- Fix long-standing iser-target logout bug related to early
conn_logout_comp completion, resulting in iscsi_conn use-after-tree
OOpsen. (Sagi + nab)
- Fix long-standing tcm_fc bug in ft_invl_hw_context() failure
handing for DDP hw offload. (DanC)
- Fix incorrect use of unprotected __transport_register_session() in
tcm_qla2xxx + other single local se_node_acl fabrics. (Bart)
- Fix reference leak in target_submit_cmd() -> target_get_sess_cmd()
for ack_kref=1 failure path. (Bart)
- Fix pSCSI backend ->get_device_type() statistics OOPs with
un-configured device. (Olaf + nab)
- Fix virtual LUN=0 target_configure_device failure OOPs at modprobe
time. (Claudio + nab)
- Fix FUA write false positive failure regression in v4.0-rc1 code.
(Christophe Vu-Brugier + HCH)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: do not reject FUA CDBs when write cache is enabled but emulate_write_cache is 0
target: Fix virtual LUN=0 target_configure_device failure OOPs
target/pscsi: Fix NULL pointer dereference in get_device_type
tcm_fc: missing curly braces in ft_invl_hw_context()
target: Fix reference leak in target_get_sess_cmd() error path
loop/usb/vhost-scsi/xen-scsiback: Fix use of __transport_register_session
tcm_qla2xxx: Fix incorrect use of __transport_register_session
iscsi-target: Avoid early conn_logout_comp for iser connections
Revert "iscsi-target: Avoid IN_LOGOUT failure case for iser-target"
target: Disallow changing of WRITE cache/FUA attrs after export
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change from using the __raw IO accesors to the endian agnostic versions
of readl/writel_relaxed when not on AVR32. This fixes issues with running
big endian on ARMv7.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The seq_printf/seq_puts/seq_putc return values, because they
are frequently misused, will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Miscellanea:
o Coalesce formats, realign arguments
o Create static functions for statement expression macros
o Use c90 style comments instead of c99
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit updates udc core vbus status, and try to connect
or disconnect gadget.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of iterate to find usb_udc according to usb_gadget, this
way is easier.
Alan Stern suggests this way too:
http://marc.info/?l=linux-usb&m=142168496528894&w=2
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of manual device_create_file() and device_remove_file() calls,
assign the static attribute groups to the lun device to register.
The RO or RW permissions for some entries are decided in is_visible
callback. This simplifies the code (also the logic) and avoids the
possible races, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull gadgetfs fixes from Al Viro:
"Assorted fixes around AIO on gadgetfs: leaks, use-after-free, troubles
caused by ->f_op flipping"
* 'gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
gadgetfs: really get rid of switching ->f_op
gadgetfs: get rid of flipping ->f_op in ep_config()
gadget: switch ep_io_operations to ->read_iter/->write_iter
gadgetfs: use-after-free in ->aio_read()
gadget/function/f_fs.c: switch to ->{read,write}_iter()
gadget/function/f_fs.c: use put iov_iter into io_data
gadget/function/f_fs.c: close leaks
move iov_iter.c from mm/ to lib/
new helper: dup_iter()
Most callers in the kernel want to perform synchronous file I/O, but
still have to bloat the stack with a full struct kiocb. Split out
the parts needed in filesystem code from those in the aio code, and
only allocate those needed to pass down argument on the stack. The
aio code embedds the generic iocb in the one it allocates and can
easily get back to it by using container_of.
Also add a ->ki_complete method to struct kiocb, this is used to call
into the aio code and thus removes the dependency on aio for filesystems
impementing asynchronous operations. It will also allow other callers
to substitute their own completion callback.
We also add a new ->ki_flags field to work around the nasty layering
violation recently introduced in commit 5e33f6 ("usb: gadget: ffs: add
eventfd notification about ffs events").
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
USB_DIR_OUT happens to be zero, so the result of bitwise and is always 0.
Consequently, break will never happen in the SOFT_RESET case.
This patch uses a compatible condition with a non-zero USB_DIR_IN,
which might or might not evaluate to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was a missing goto so we free "opts" and then dereference it.
Fixes: ee1cd515e8 ('usb: gadget: printer: add configfs support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u16 so it can't go higher than 65535. kstrtou16() has a
range check built in so this is already handled.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use %ps for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pf expects a function descriptor
(which is not what __builtin_return_address returns).
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: linux-usb@vger.kernel.org
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc is then checked for NULL, if NULL, it is then dereferenced as
udc->dev, it is found using Coccinelle.
We simplify the code to fix this problem, and we delete some conditions
at if {} which will never be met.
Reported-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reported-by : Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function usb_ep_disable() causes completion of all requests queued
for given endpoint, so there is no need to dequeue them after endpoint
disabling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not everybody uses a utf8 locale (unfortunately), so let's avoid
non-ascii characters in the kernel log. Replace the 3-byte utf8
sequence with a 3-byte ascii equivalent.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch add suspend/resume with wakeup support for Atmel USBA.
On suspend: We stay continuously clocked if Vbus signal is not
available. If Vbus signal is available we set the Vbus signal as a wake
up source then we stop the USBA itself and all clocks used by USBA.
On resume: We recover clocks and USBA if we stopped them. If a device is
currently connected at resume time we enable the controller.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI)
we will reduce power consumption by switching off the USB PLL if no USB
Host is currently connected to this USB Device.
We are using Vbus GPIO signal to detect Host presence. If Vbus signal is
not available then the device stays continuously clocked.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Vbus IRQ handler needs a started UDC driver to work because it uses
udc->driver, which is set by the UDC start handler. The previous way
chosen was to return from interrupt if udc->driver is NULL using a
spinlock around the check.
We now request an auto disabled (IRQ_NOAUTOEN) Vbus signal IRQ instead
of an auto enabled IRQ followed by disable_irq(). This way we remove the
very small timeslot of enabled IRQ which existed previously between
request() and disable(). We don't need anymore to check if udc->driver
is NULL in IRQ handler.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If vbus gpio is high at init, we should set vbus_prev to true
accordingly to the current vbus state. Without that, we skip the first
vbus interrupt because the saved vbus state is not consistent.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
replace numeric value with TYPE_NO_LUN (defined in <scsi/scsi.h>)
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix some spelling typo found in gadget.xml.
It is because this file is generated from comments in sources,
I had to fix comments in the source, instead of xml file itself.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit ef11982dd7.
That commit creates a problem for some UDCs (at least musb)
where it allocates an endpoints with a 64-byte FIFO, but later
tries to use that same FIFO for 1024-byte packets.
Before implementing this, composite framework needs to be
modified so we only allocate endpoints after we know negotiated
speed, however that needs quite a bit of extra work.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for configfs interface so that f_printer can be used as a
component of usb gadgets composed with it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Substitute some boilerplate code with a dedicated macro.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old interface users left, so it can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The goal is to remove the old function interface, so its (only) user
must be converted to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support, a usb function must be converted to use
the new interface. This patch converts the function to the new interface
and provides backward compatiblity layer, which can be removed after
all its users are converted to use the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The legacy printer gadget now contains both a reusable printer function
and legacy gadget proper implementations interwoven, but logically
separate. This patch factors out a reusable f_printer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With all the obstacles removed it is possible to allow more than one
instance of the printer function. Since the function requires allocating
character device region, a maximum number of allowed instances is defined.
Such an approach is used in f_acm and in f_hid.
With multiple instances it does not make sense to depend on a
lock_printer_io member of a dynamically allocated (and destroyed) struct
printer_dev to clean up after all instances of the printer function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Verify that a given usb_ctrlrequest is meant for printer function.
The following parts of the request are tested:
- bmRequestType:Data transfer direction
- bmRequestType:Type
- bmRequestType:Recipient
- bRequest
- wValue for bRequest 1 and 2
- wLength
Additionally, the request is considered meant for this function
iff the decoded interface number matches dev->interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Non-standard requests can encode the actual interface number in a
non-standard way. For example composite_setup() assumes
that it is w_index && 0xFF, but the printer function encodes the interface
number in a context-dependet way (either w_index or w_index >> 8).
This can lead to such requests being directed to wrong functions.
This patch adds req_match() method to usb_function. Its purpose is to
verify that a given request can be handled by a given function.
If any function within a configuration provides the method and it returns
true, then it is assumed that the right function is found.
If a function uses req_match(), it should try as hard as possible to
determine if the request is meant for it.
If no functions in a configuration provide req_match or none of them
returns true, then fall back to the usual approach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
5 uses of container_of() in the same context justify wrapping it
in a static inline function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The printer_dev can be recovered from printer_func_unbind() function's
parameters.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The mutex is a legacy after semi-automatic Big Kernel Lock removal.
printer_open() does its own locking, so no need to duplicate it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Call gprinter_setup() from gadget's bind instead of module's init.
Call gprinter_cleaup() corerspondingly. This detaches printer function's
logic from legacy printer gadget's implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Factor out gprinter_setup() and gprinter_cleanup() so that it is
easy to change the place they are called from.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer, the function's code should
not use file global variables related to legacy printer gadget's
implementation.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
printer_cfg_unbind() becomes empty, so it is removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conversion to the new function interface requires splitting a
<something>_bind_config() function into two parts: allocation of
container_of struct usb_function and invocation of usb_add_function().
This patch moves the latter to the end of the f_printer_bind_config()
in order to enable conversion to the new interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to factor out a reusable f_printer.c, the code related to the
function should be placed in functions related to the function.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Follow the convention of distributing source code between
<something>_do_config() and <something>_bind_config().
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Legacy gadgets, before converting them to the new function framework,
used to use the name <something>_do_config() for usb_add_config()'s
callback.
This patch changes the name so that it is easier to follow
the convention.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pdev member of struct printer_dev is not used outside
printer_bind_config(), so it can just as well be a local variable there.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If cdev_add() in printer_bind_config() fails, care is taken to
reverse the effects of initializations completed until the fail
happens. But if printer_req_alloc() fails, it is just one of the
two lists that is cleaned up while the effects of cdev_add()
and device_create() are not reverted.
This patch changes error handling so that at least as much cleanup is done
as when a failure happens before printer_req_alloc() invocations.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever the "goto fail" branch is taken, the effect of usb_add_function()
should be reverted.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct printer_dev contains 3 list heads: tx_reqs, rx_reqs and rx_buffers.
There is just one instance of this structure in the driver and it is
file static, and as such initialized with all zeros.
If device_create() or cdev_add() fails then "goto fail" branch is taken,
which results in printer_cfg_unbind() call. The latter checks if
tx_reqs, rx_reqs and rx_buffers lists are empty. The check for emptiness
is in fact a check whether the "next" member of struct list_head points
to the head of the list. But the heads of the lists in question have
not been initialized yet and, as mentioned above, contain all zeros,
so list_empty() returns false and respective "while" loop body starts
executing. Here, container_of() just subtracts the offset of a struct
usb_request member from an address of this same member, which results in
a value somewhere near 0 or 0xfff...ff. And the argument to list_del()
dereferences such a pointer which causes a disaster.
This patch moves respective INIT_LIST_HEAD() invocations to a point before
"goto fail" branch can be taken.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The unbind() method is optional is usb_composite_driver.
In this particular driver the method does nothing so it can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function-specific setup requests should be handled in such a way, that
apart from filling in the data buffer, the requests are also actually
enqueued: if function-specific setup is called from composte_setup(),
the "usb_ep_queue()" block of code in composite_setup() is skipped.
The printer function lacks this part and it results in e.g. get device id
requests failing: the host expects some response, the device prepares it
but does not equeue it for sending to the host, so the host finally asserts
timeout.
This patch adds enqueueing the prepared responses.
Cc: <stable@vger.kernel.org> # v3.4+
Fixes: 2e87edf492: "usb: gadget: make g_printer use composite"
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a non-standard request is processed and its parameters just happen
to match those of some standard request, the logic of composite_setup()
can be fooled, so don't even try any switch cases, just go to the
proper place where unknown requests are handled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Silence the following warning:
drivers/usb/gadget/udc/net2280.c:3176:33: warning: context imbalance in
'handle_stat1_irqs' - unexpected unlock
Signed-off-by: Felipe Balbi <balbi@ti.com>
net2280_start can be called with pullup disabled. Don't set
softconnect flag in it. Let net2280_pullup handle the connection part.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hopefully, these prints will help localize the problems faster.
[ balbi@ti.com: removed 2 unnecessary OOM error messages ]
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove fiforegs from struct net2280 and net2280_ep as it is unused.
By the way, ep->fiforegs = &dev->fiforegs[i] assignment is incorrect.
It should be ep->fiforegs = &dev->fiforegs[ne[i]], but it doesn't
matter now.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Each struct usb_ep added for net2280 can be used in either direction.
Whereas, each struct usb_ep for usb3380 has fixed direction. Use
ep_autoconf compatible names so that endpoint with correct direction
can be selected.
Name sequence is due to the logic in usb_reinit_338x() in ne[] and
ep_reg_addr[].
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
While there, simplify the error handler logic by returning
immediately and remove the unnecessary labels.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED. So they'd be failing just fine until that
first write() anyway. Let's do the following:
* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
* in ep_write_iter(), after success of get_ready_ep() turn
if (!usb_endpoint_dir_in(&epdata->desc)) {
into
if (epdata->state == STATE_EP_ENABLED &&
!usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The V4L2 core will warn if this is not done. Unfortunately this driver
wasn't updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of .ioctl use unlocked_ioctl. This allows us to finally remove
the old .ioctl op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch this driver over to the V4L2 core locking mechanism in preparation
for switching to unlocked_ioctl. Suggested by Laurent Pinchart.
This patch introduces a new mutex at the struct uvc_video level and
drops the old mutex at the queue level. The new lock is now used for all
ioctl locking and in the release file operation (the driver always has
to take care of locking in file operations, the core only serializes
ioctls).
Note that the mmap and get_unmapped_area file operations no longer take
a lock. Commit f035eb4e97 fixed a AB-BA
deadlock by moving all the locking down into vb2, so the mmap and
get_unmapped_area file operations should no longer do any locking before
calling into vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145f: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
AIO_PREAD requests call ->aio_read() with iovec on caller's stack, so if
we are going to access it asynchronously, we'd better get ourselves
a copy - the one on kernel stack of aio_run_iocb() won't be there
anymore. function/f_fs.c take care of doing that, legacy/inode.c
doesn't...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
This one was driving me mad, with several lines of warnings during the
allmodconfig build for a single bogus pointer cast. The warning was so
verbose due to the indirect macro expansion explanation, and the whole
thing was just for a debug printout.
The bogus pointer-to-integer cast was pointless anyway, so just remove
it, and use '%p' to show the pointer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsl udc core assumes itself always self powered, so set is_selfpowered
is 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The purpose of the functions and their parametrs might not be obvious
to the reader, so explain it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first parameter of __uvcg_iter_strm_cls() is always used in
the context of struct uvcg_streaming_header, so change the
function prototype accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that this is DRD, it doesn't make sense to keep it under
drivers/usb/host.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ISP1761 is a dual-mode host and device controller backward
compatible on the host side with the ISP1760. Add support for the device
controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixed the following warnings (reported by cppcheck):
[drivers/usb/gadget/function/f_sourcesink.c:1217]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1261]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1305]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1349]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1393]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1437]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1476]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1520]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1564]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1608]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'
Reviewed-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add eventfd which notifies userspace about ep0 events and AIO completion
events. It simplifies using of FunctionFS with event loop, because now
we need to poll on single file (instead of polling on ep0 and eventfd's
supplied to AIO layer).
FunctionFS eventfd is not triggered if another eventfd is supplied to
AIO layer (in AIO request). It can be useful, for example, when we want
to handle AIO transations for chosen endpoint in separate thread.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use if-loop variable 'epfile' instead of start variable 'epfiles'. Now the
correct endpoint file name is stored.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB vendor type is encoded in field bmRequestType. Make test USB_TYPE_VENDOR
with bRequestType instead of bRequest.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
__uvcg_fill_strm() called from __uvcg_iter_stream_cls()
might have advanced the "data" even if __uvcg_iter_stream_cls()
returns an error, so use a backup copy as an argument to kfree().
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of custom approach the patch converts code to use %pM specifier to
print MAC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1) Change "conv" an "vnoc" to "to_cpu_endian" to "to_little_endian".
2) No need to check the "limit" because that is already handled in
kstrtoXX so delete that parameter along with the check.
3) By using a "bits" parameter, we can combine the "uxx" parameter and
the "str2u" parameters.
4) The kstrtou##bits() conversion does not need to be done under the
mutex so move it to the start of the function.
5) Change the name of "identity_conv" to "noop_conversion".
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to add a kfree(h) on an error path.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"num" is a u32 so "(num > 0xFFFFFFFF)" is never true. Also the range
is already checked in kstrtou32().
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We're basically saying ERR_CAST(NULL) and PTR_ERR(NULL) here, which is
nonsensical.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we can compose gadgets from many functions, there is the problem
related to gadget breakage while FunctionFS daemon being closed. FFS
function is userspace code so there is no way to know when it will close
files (it doesn't matter what is the reason of this situation, it can
be daemon logic, program breakage, process kill or any other). So when
we have another function in gadget which, for example, sends some amount
of data, does some software update or implements some real-time functionality,
we may want to keep the gadget connected despite FFS function is no longer
functional.
We can't just remove one of functions from gadget since it has been
enumerated, so the only way to keep entire gadget working is to make
broken FFS function deactivated but still visible to host. For this
purpose this patch introduces "no_disconnect" mode. It can be enabled
by setting mount option "no_disconnect=1", and results with defering
function disconnect to the moment of reopen ep0 file or filesystem
unmount. After closing all endpoint files, FunctionFS is set to state
FFS_DEACTIVATED.
When ffs->state == FFS_DEACTIVATED:
- function is still bound and visible to host,
- setup requests are automatically stalled,
- transfers on other endpoints are refused,
- epfiles, except ep0, are deleted from the filesystem,
- opening ep0 causes the function to be closed, and then FunctionFS
is ready for descriptors and string write,
- altsetting change causes the function to be closed - we want to keep
function alive until another functions are potentialy used, altsetting
change means that another configuration is being selected or USB cable
was unplugged, which indicates that we don't need to stay longer in
FFS_DEACTIVATED state
- unmounting of the FunctionFS instance causes the function to be closed.
Tested-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/gadget/function/uvc_configfs.c:46:28: sparse: symbol 'to_uvcg_control_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:138:25: sparse: symbol 'uvcg_control_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:164:6: sparse: symbol 'uvcg_control_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:721:20: sparse: symbol 'to_uvcg_format' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:798:30: sparse: symbol 'to_uvcg_streaming_header' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:950:25: sparse: symbol 'uvcg_streaming_header_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:976:6: sparse: symbol 'uvcg_streaming_header_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1020:19: sparse: symbol 'to_uvcg_frame' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1265:25: sparse: symbol 'uvcg_frame_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1315:6: sparse: symbol 'uvcg_frame_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1338:26: sparse: symbol 'to_uvcg_uncompressed' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1548:25: sparse: symbol 'uvcg_uncompressed_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1586:6: sparse: symbol 'uvcg_uncompressed_drop' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1610:19: sparse: symbol 'to_uvcg_mjpeg' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1761:25: sparse: symbol 'uvcg_mjpeg_type' was not declared. Should it be static?
drivers/usb/gadget/function/uvc_configfs.c:1793:6: sparse: symbol 'uvcg_mjpeg_drop' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we call gaudio_cleanup at f_audio_free, the f_uac1_opts
doesn't need to use gaudio any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate udc structure instead of relying on the statically declared
object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
cpu_is_at91xxx are a set of macros defined in mach/cpu.h and are here used
to detect the SoC we are booting on.
Use compatible string + a caps structure to replace those cpu_is_xxx tests.
Remove all mach and asm headers (which are now unused).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make use of devm_ functions to simplify probe and remove code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since non-DT board support has been removed from the at91 architecture we
can safely remove non-DT handling code.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that at91 system clocks forward set_rate request to their parent we
can remove the uclk clock and directly call clk_set_rate on fclk.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The driver is requesting clock by their global name (those declared in the
clk_lookup list), but this only works with !CCF kernels.
Now that all SoCs have moved to CCF, fix the driver to use local names
(hclk and pclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fj7
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc5
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy.c
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UDC core has already done it before .udc_stop and after .udc_start.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of using variable length array, use a static length equal to
the size of the ffs->ev.types array. This gets rid of a sparse warning:
drivers/usb/gadget/function/f_fs.c:401:44: warning:
Variable length array is used.
and makes it more explicit that the array has a very tight upper size
limit. Also add some more documentation about the ev.types array and
how its size is limited and affects the rest of the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cache INT_ENB register value in order to avoid uncached iomem access, and
thus improve access time to INT_ENB value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Avoid interpreting useless status flags when we're not waiting for such
events by masking the status variable with the interrupt enabled register
value.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9g45 and at91sam9x5 SoCs have an hardware bug forcing us to
generate a pulse on the BIAS signal on "USB end of reset” and
“USB end of resume" events.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: Patrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.
This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.
Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.
Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some debug messages were not build due to unconditional #if 0.
These messages are very useful for debugging and the user can enable
them on demand via dynamic debug.
If they are not enabled the performance is not affected.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ASSERT_OUT_NAKING was only called by out_flush and was hidden behind a
ifdef.
This patch moves the inline function into out_flush and remove the
ifdef. The user can decide to print the debug message or not via dynamic
printk
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After fix superspeed dma_done was applied we can simplify the code by
removing the duplicated dma_done and letting the function check if there
are more completed dma transactions.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function is very simple, does not declare any variable and it is
called in the irq path.
The counterpart for net228x is already declared as inline.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function resume_dma is not used, remove it.
The reason the compiler did not catch this dead code is the inline
modifier.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
