Remove unneeded check that caused problems with jumbo frame sizes.
The check was recently added and is wrong.
When using jumbo frames the sky2 driver does fragmentation, so
rx_data_size is less than mtu.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct printk with PFX before KERN_ in bcm43xx_wx.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DMA-mapped SMP (scsi management protocol) requests going /to/ the device
need the PCI DMA data direction to indicate such.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dm9601 didn't take the ethernet header into account when calculating
RX MTU, causing packets bigger than 1486 to fail.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver erroneously zeros dev->tx_queue_len, since
mp->tx_ring_size has not yet been initialized. Actually,
the driver shouldn't modify tx_queue_len at all and should
leave the value set by alloc_etherdev(), currently 1000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix 4032 chip undocumented "feature" where bit-8 is set
if the inbound completion is for a VLAN.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's a different version of DMI table for TECRA M3 where it has
proper vendor and product name entry. Add the entry to the broken
suspend list.
Angus Turnbull reported and provided initial patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Angus Turnbull <angus@twinhelix.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TCP V4 sequence numbers are 32bits, and RFC 793 assumed a 250 KHz clock.
In order to follow network speed increase, we can use a faster clock, but
we should limit this clock so that the delay between two rollovers is
greater than MSL (TCP Maximum Segment Lifetime : 2 minutes)
Choosing a 64 nsec clock should be OK, since the rollovers occur every
274 seconds.
Problem spotted by Denys Fedoryshchenko
[ This bug was introduced by f859581519 ]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling the RELDISP VT ioctl, we are reading vt_newvt while the
console workqueue could be messing with it (through change_console()). We
fix this race by taking the console semaphore before reading vt_newvt.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix missing symbols in libertas USB driver when it is modular and rest
of libertas is built-in.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using udma yuv causes the driver becomes locked into that mode. This prevents
use of the mpeg decoder & non-udma yuv output. This patch clears the
operating mode when the device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The new behaviour of CFS exposes a race which occurs if a switch is
requested when vt_mode.mode is VT_PROCESS.
The process with vc->vt_pid is signaled before vc->vt_newvt is set.
This causes the switch to fail when triggered by the monitoing process
because the target is still -1.
[ If the signal sending fails, the subsequent "reset_vc(vc)" will then
reset vt_newvt to -1, so this works for that case too. - Linus ]
Signed-off-by: Jan Lübbe <jluebbe@lasnet.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 468d09f894 masked the "state"
interrupt (bit 20 of the cause register). This results in Radstone's
PPC7D repeatedly re-entering the interrupt routine, locking up the
board. The following patch returns the required handling for this
interrupt.
Signed-off-by: Martyn Welch <martyn.welch@radstone.co.uk>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.
This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Input: xpad - fix dependancy on LEDS class
The driver can not be built-in when LEDS class is a module.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
e1000: Add device IDs of blade version of the 82571 quad port
sky2: fix transmit state on resume
sky2: FE+ vlan workaround
sky2: sky2 FE+ receive status workaround
in cpm_uart_cpm1.h, DPRAM_BASE is assigned an address derived from cpmp.
On ARC=ppc, this is a physical address with 1:1 DMA mapping which can't
be used for arithmetric compare operations with virtual addresses
returned by cpm_dpram_addr. This patch changes the assignment to use
cpm_dpram_addr as well, like in cpm_uart_cpm2.h.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This blade-specific board form factor is identical to the 82571EB
board.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This should fix http://bugzilla.kernel.org/show_bug.cgi?id=8667
After resume, driver has reset the chip so the current state
of transmit checksum offload state machine and DMA state machine
will be undefined.
The fix is to set the state so that first Tx will set MSS and offset
values.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The FE+ workaround means the driver can no longer trust the status register
to indicate VLAN tagged frames. The fix for this is to just disable VLAN
acceleration for that chip version. Tested and works fine.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon FE+ chip appears to have a hardware glitch that causes bogus
receive status values to be posted. The data in the packet is good, but
the status value is random garbage. As a temporary workaround until the
problem is better understood, implement the workaround the vendor driver
used of ignoring the status value on this chip.
Since this means trusting dodgy hardware values; add additional checking
of the receive packet length.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code is ported from the DRM git tree and allows the vblank interrupts
to function on the i965 hw. It also requires a change in Mesa's 965 driver
to actually use them.
[ Without this patch, my 965GM drops vblank interrupts - Jesse ]
Signed-off-by: Dave Airlie <airlied@linux.ie>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following patch silents;
...
drivers/char/hpet.c:72: warning: 'clocksource_hpet' defined but not used
drivers/char/hpet.c:81: warning: 'hpet_clocksource' defined but not used
...
build warnings on i386, they appeared after commit 3b2b64fd31
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
--
drivers/char/hpet.c | 3 +++
1 files changed, 3 insertions(+), 0 deletions(-)
duplicated .mmap in one, .vidioc_s_audio misspelled as .vidioc_g_audio
in other
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Stephen Hemminger says, this is a "belt and suspenders" patch that
zeroes the envp array at allocation time, even though all the users
should NULL-terminate it anyway (and we've hopefully fixed everybody
that doesn't do that).
And we'll apparently clean the whole envp thing up for 2.6.24 anyway.
But let's just be robust, and do both this *and* make sure that all
users are doing the right thing.
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_sis: add missing UDMA5 timing value in sis_66_set_dmamode()
sata_sil24: fix IRQ clearing race when PCIX_IRQ_WOC is used
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: hpet: ACPI Error (utglobal-0126): Unknown exception code: 0xFFFFFFF0
ACPI: CONFIG_ACPI_SLEEP=n power off regression in 2.6.23-rc8 (NOT in rc7)
ACPI: suspend: build-fix for CONFIG_SUSPEND=n and CONFIG_HIBERNATION=y
Include SYSRQ support for SUNSAB if SUNSAB_CONSOLE is selected
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the ->unique_id is set too late, the ESP scsi host
instance numbers in the kernel log during probing are
wrong.
Bug reported by Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sis_66_set_dmamode() also handles early UDMA100 (SIS630 ET) but is
missing udma timing value for UDMA100. According to sis5513, this
should be 0x8000. This caused UDMA100 device to fail on pata_sis till
it downgrades to UDMA66 while it works fine on sis5513 at UDMA100.
Reported by Adam Blech.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adam Blech <desaster.area@addcom.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When PCIX_IRQ_WOC is used, sil24 has an inherent race condition
between clearing IRQ pending and reading IRQ status. If IRQ pending
is cleared after reading IRQ status, there's possibility of lost IRQ.
If IRQ pending is cleared before reading IRQ status, spurious IRQs
will occur.
sata_sil24 till now cleared IRQ pending after reading IRQ status thus
losing IRQs on machines where PCIX_IRQ_WOC was used. Reverse the
order and ignore spurious IRQs if PCIX_IRQ_WOC.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If hpet has been initialized before registering hpet driver, the callback
function of hpet_resources will return the status code of -EBUSY, which is
not defined in the ACPI exception table. So when ACPI checks the status
code of callback function, it will report the unknown exception code.
So the status code in ACPI is used instead of the generic error code in the
ACPI callback function of hpet_resources.
For example: -EBUSY is replaced by AE_ALREADY_EXISTS
-EINVAL is replaced by AE_NO_MEMORY
http://bugzilla.kernel.org/show_bug.cgi?id=8630
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes compilation with CONFIG_SUSPEND unset and CONFIG_HIBERNATION set
(raf. http://marc.info/?l=linux-acpi&m=119055289723895&w=4).
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
Revert "drivers/net/pcmcia/3c589_cs: fix port configuration switcheroo"
sky2: be more selective about FIFO watchdog
sky2: FE+ Phy initialization
r8169: workaround against ignored TxPoll writes (8168)
r8169: correct phy parameters for the 8110SC
The assembly templates for lguest guest patching are in the .init.text
section. This means that modules get patched with "cc cc cc cc" or similar
junk.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to null terminate environment. Found by inspection while looking for
similar problems to platform uevent bug
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vma_data structure may be shared by vma's from multiple tasks, with no
way of knowing which areas are shared or not shared, so release/clear pages
only when the refcount (of vma's) goes to zero.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit fadacb1b80.
The change being reverted made the driver consistent with
include/linux/netdevice.h, but then inconsistent with the other PCMCIA
ethernet drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Idle count should only be incremented when touchpad button
is not pressed, otherwise reset may happen at a wrong time
and touchpad will never report button release event.
Signed-off-by: Thomas Rohwer <trohwer@tng.de>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Be more selective about when to enable the ram buffer watchdog code.
It is unnecessary on XL A3 or later revs, and with Yukon FE
the buffer is so small (4K) that the watchdog detects false positives.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One more snippet of PHY initialization required for FE+ chips.
Discovered in latest sk98lin 10.21.1.3 driver.
Please apply to 2.6.23.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1/ ops_complete_biofill tried to avoid calling handle_stripe since all the
state necessary to return read completions is available. However the
process of determining whether more read requests are pending requires
locking the stripe (to block add_stripe_bio from updating dev->toead).
ops_complete_biofill can run in tasklet context, so rather than upgrading
all the stripe locks from spin_lock to spin_lock_bh this patch just
unconditionally reschedules handle_stripe after completing the read
request.
2/ ops_complete_biofill needlessly qualified processing R5_Wantfill with
dev->toread. The result being that the 'biofill' pending bit is cleared
before handling the pending read-completions on dev->read. R5_Wantfill can
be unconditionally handled because the 'biofill' pending bit prevents new
R5_Wantfill requests from being seen by ops_run_biofill and
ops_complete_biofill.
Found-by: Yuri Tikhonov <yur@emcraft.com>
[neilb@suse.de: simpler fix for bug 1 than moving code]
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix data corruption triggered by wrong headroom marking order
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching"). We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data. This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).
We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern). The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
device_suspend() calls ACPI suspend functions, which seems to have undesired
side effects on lower idle C-states. It took me some time to realize that
especially the VAIO BIOSes (both Andrews jinxed UP and my elfstruck SMP one)
show this effect. I'm quite sure that other bug reports against suspend/resume
about turning the system into a brick have the same root cause.
After fishing in the dark for quite some time, I realized that removing the ACPI
processor module before suspend (this removes the lower C-state functionality)
made the problem disappear. Interestingly enough the propability of having a
bricked box is influenced by various factors (interrupts, size of the ram image,
...). Even adding a bunch of printks in the wrong places made the problem go
away. The previous periodic tick implementation simply pampered over the
problem, which explains why the dyntick / clockevents changes made this more
prominent.
We avoid complex functionality during the boot process and we have to do the
same during suspend/resume. It is a similar scenario and equaly fragile.
Add suspend / resume functions to the ACPI processor code and disable the lower
idle C-states across suspend/resume. Fall back to the default idle
implementation (halt) instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: suspend: consolidate handling of Sx states addendum
ACPI: suspend: consolidate handling of Sx states.
ACPI: video: remove dmesg spam
ACPI: video: _DOS=0 by default to prevent hotkey hang
What guest drivers?
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Domain Validation in the SPI transport class is failing on boxes with
damaged cables (and failing to the extent that the box hangs). The
problem is that the first test it does is a cable integrity test for
wide transfers and if this fails, it turns the wide bit off. The
problem is that the next set of tests it does turns wide back on
again, with the result that it runs through the entirety of DV with a
known bad setting and then hangs the system.
The attached patch fixes the problem by physically nailing the wide
setting to what it deduces it should be for the whole of Domain
Validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the S0 state be always reported as supported
Signed-off: Frans Pop <elendil@planet.nl>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Recent changes to sleep initialization in ACPI dropped reporting of supported Sx
states above S3. Fix that and also move S5 init into same file as other Sx.
The only functional change is adding printk() for S4 and S5 cases.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Need to null terminate environment. Found by inspection
while looking for similar problems to platform uevent bug
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ahci: add ATI SB800 PCI IDs
libata-sff: Fix documentation
libata: Update the blacklist with a few more devices
ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: henry su <henry.su.ati@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.
As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.
This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: Pierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module. Dmesg:
PCI: Device 0000:02:07.0 not available because of resource collisions
ohci1394: Failed to enable OHCI hardware.
This was reported for a Toshiba Satellite 5100-503. The cause is commit
8df4083c52 in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire. This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit. Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add the DIS_EARLY_DAC PHY workaround for 5709 A1. Without it, link
sometimes does not come up.
Update version to 1.6.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes pppol2tp_xmit call skb_cow_head so that we don't modify
cloned skb data. It also gets rid of skb2 we only need to preserve the
original skb for congestion notification, which is only applicable for
ppp_async and ppp_sync.
The other semantic change made here is the removal of socket accounting
for data tranmitted out of pppol2tp_xmit. The original code leaked any
existing socket skb accounting. We could fix this by dropping the
original skb owner. However, this is undesirable as the packet has not
physically left the host yet.
In fact, all other tunnels in the kernel do not account skb's passing
through to their own socket. In partciular, ESP over UDP does not do
so and it is the closest tunnel type to PPPoL2TP. So this patch simply
removes the socket accounting in pppol2tp_xmit. The accounting still
applies to control packets of course.
I've also added a reminder that the outgoing checksum here doesn't work.
I suppose existing deployments don't actually enable checksums.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pppol2tp_recv_core doesn't handle non-linear packets properly.
It also fails to check the remote offset field.
This patch fixes these problems. It also removes an unnecessary check on
the UDP header which has already been performed by the UDP layer.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of UDP-Lite we need to refine the socket check so
that only genuine UDP sockets are allowed through.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I got rid of the second packet in __pppoe_xmit I created
a double-free on the skb because of the goto abort on failure.
This patch removes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export phy_mii_ioctl, so network drivers can use it when built
as modules too.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 8168 ignores the requests to fetch the Tx descriptors when
the relevant TxPoll bit is already set. It easily kills the
performances of the 8168. David Gundersen has noticed that it
is enough to wait for the completion of the DMA transfer (NPQ
bit is cleared) before writing the TxPoll register again.
The extra IO traffic added by the proposed workaround could be
minimalized but it is not a high-priority task.
Fix for:
http://bugzilla.kernel.org/show_bug.cgi?id=7924http://bugzilla.kernel.org/show_bug.cgi?id=8688
(http://bugzilla.kernel.org/show_bug.cgi?id=7555 ?)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Gundersen <gundy@iinet.net.au>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The phys of the 8110SC (RTL_GIGA_MAC_VER_{05/06}) act abnormally in
gigabit mode if they are applied the parameters in rtl8169_hw_phy_config
which actually aim the 8110S/SB.
It is ok to return early from rtl8169_hw_phy_config as it does not
apply to the 8101 and 8168 families.
Signed-off-by: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove unused variables from drivers/ide/ppc/pmac.c
ide: ST320413A has the same problem as ST340823A
Nested class devices used to have 'device' symlink point to a real
(physical) device instead of a parent class device. When converting
subsystems to struct device we need to keep doing what class devices did if
CONFIG_SYSFS_DEPRECATED is Y, otherwise parts of udev break.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg KH <greg@kroah.com>
Tested-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mask on i830 should be 0x70 always, later chips 0xF0 should be okay.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Acked-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Michael Haas <laga@laga.ath.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a couple drivers that do not correctly terminate their pci_device_id
lists. This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: Kees Cook <kees@ubuntu.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The shrinking of a virtual memory area that is mmap(2)'d to a memory
special file (device drivers/char/mspec.c) can cause a panic.
If the mapped size of the vma (vm_area_struct) is very large, mspec allocates
a large vma_data structure with vmalloc(). But such a vma can be shrunk by
an munmap(2). The current driver uses the current size of each vma to
deduce whether its vma_data structure was allocated by kmalloc() or vmalloc().
So if the vma was shrunk it appears to have been allocated by kmalloc(),
and mspec attempts to free it with kfree(). This results in a panic.
This patch avoids the panic (by preserving the type of the allocation) and
also makes mspec work correctly as the vma is split into pieces by the
munmap(2)'s.
All vma's derived from such a split vma share the same vma_data structure that
represents all the pages mapped into this set of vma's. The mpec driver
must be made capable of using the right portion of the structure for each
member vma. In other words, it must index into the array of page addresses
using the portion of the array that represents the current vma. This is
enabled by storing the vma group's vm_start in the vma_data structure.
The shared vma_data's are not protected by mm->mmap_sem in the fork() case
so the reference count is left as atomic_t.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the rtc driver, rtc-ds1552.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC. This breaks on 32-bit systems with
larger physical addresses.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the rtc driver, rtc-ds1742.c uses an unsigned long to store the
base mmio address of the NVRAM/RTC. This breaks on systems like PowerPC
440, which is a 32-bit core with 36-bit physical addresses: IO on the
system, including the RTC, is typically above the 4GB point, and cannot fit
into an unsigned long.
This patch fixes the problem by replacing the unsigned long with a
resource_size_t. Tested on Ebony (PPC440) (with additional patches to
instantiate the ds1742 platform device appropriately).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc32:
drivers/block/DAC960.c: In function 'DAC960_V1_EnableMemoryMailboxInterface':
drivers/block/DAC960.c:1168: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
drivers/block/DAC960.c:1168: error: (Each undeclared identifier is reported only
Cc: <dac@conglom-o.org>
Cc: <stable@kernel.org>
Cc: Alessandro Polverini <alex@nibbles.it>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i am actually heavily using the ACPI video extension for my Thinkpad X61
Tablet. I have bound the input events triggered by the brightness
up/down keys to a simple
echo <value> > /sys/class/backlight/acpi_video1/brightness
but everytime the event is triggered and acpi_video_device_lcd_set_level()
is called i got a notificication in my kernel log like:
set_level status: 0
set_level status: 0
set_level status: 0
set_level status: 0
...
Signed-off-by: Maik Broemme <mbroemme@plusserver.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In the past, the Linux/ACPI video driver invoked _DOS
(Display Output Switch) with the parameter 1
to tell the BIOS to switch the video output display for us.
But this conflicts with Linux native graphics drivers,
and can cause all sorts of issues, including hanging the system.
http://bugzilla.kernel.org/show_bug.cgi?id=6001
Here we change the Linux default to evaluate _DOS=0,
which tells the BIOS to simply send us a hotkey event
and not touch the graphics hardware.
The acpi video driver sends the display switch hotkey
event up through the intput layer, and X can interpret
that and use its native graphics driver to switch the display.
For the case where Linux has no native graphics driver running,
or the graphics driver doesn't know how to switch video and
the BIOS (safely) does, the previous behaviour can be restored with:
# echo 1 > /proc/acpi/video/*/DOS
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* don't register irq until ->startup() (and release in ->shutdown()).
That avoids oopsen with the current tree when interrupt comes before we'd
set up the data structures for ttyb.
* handle console=ttyS... even when OBP talks to screen/keyboard
* register irq handler for each port, let kernel/irq/handle.c
call it for both if needed. Kills code duplication in sunsab_interrupt().
BTW, there'd been bitrot in it - ttya handling had stopped calling
check_status() on BRK (correctly), ttyb copy of that code had kept the
bogus call in that case.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name it thinkpad-acpi version 0.16 to avoid any confusion with some 0.15
thinkpad-acpi development snapshots and backports that had input layer
support, but no hotkey_report_mode support.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Revert new 2.6.23 CONFIG_THINKPAD_ACPI_INPUT_ENABLED Kconfig option because
it would create a legacy we don't want to support.
CONFIG_THINKPAD_ACPI_INPUT_ENABLED was added to try to fix an issue that is
now moot with the addition of the netlink ACPI event report interface to
the ACPI core.
Now that ACPI core can send events over netlink, we can use a different
strategy to keep backwards compatibility with older userspace, without the
need for the CONFIG_THINKPAD_ACPI_INPUT_ENABLED games. And it arrived
before CONFIG_THINKPAD_ACPI_INPUT_ENABLED made it to a stable mainline
kernel, even, which is Good.
This patch is in sync with some changes to thinkpad-acpi backports, that
will keep things sane for userspace across different combinations of kernel
versions, thinkpad-acpi backports (or the lack thereof), and userspace
capabilities:
Unless a module parameter is used, thinkpad-acpi will now behave in such a
way that it will work well (by default) with userspace that still uses only
the old ACPI procfs event interface and doesn't care for thinkpad-acpi
input devices.
It will also always work well with userspace that has been updated to use
both the thinkpad-acpi input devices, and ACPI core netlink event
interface, regardless of any module parameter.
The module parameter was added to allow thinkpad-acpi to work with
userspace that has been partially updated to use thinkpad-acpi input
devices, but not the new ACPI core netlink event interface. To use this
mode of hot key reporting, one has to specify the hotkey_report_mode=2
module parameter.
The thinkpad-acpi driver exports the value of hotkey_report_mode through
sysfs, as well. thinkpad-acpi backports to older kernels, that do not
support the new ACPI core netlink interface, have code to allow userspace
to switch hotkey_report_mode at runtime through sysfs. This capability
will not be provided in mainline thinkpad-acpi as it is not needed there.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Richard Hughes <hughsient@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: Fix net_device leak.
[PPP] generic: Fix receive path data clobbering & non-linear handling
[PPP] generic: Call skb_cow_head before scribbling over skb
[NET] skbuff: Add skb_cow_head
[BRIDGE]: Kill clone argument to br_flood_*
[PPP] pppoe: Fill in header directly in __pppoe_xmit
[PPP] pppoe: Fix data clobbering in __pppoe_xmit and return value
[PPP] pppoe: Fix skb_unshare_check call position
[SCTP]: Convert bind_addr_list locking to RCU
[SCTP]: Add RCU synchronization around sctp_localaddr_list
[PKT_SCHED]: sch_cbq.c: Shut up uninitialized variable warning
[PKTGEN]: srcmac fix
[IPV6]: Fix source address selection.
[IPV4]: Just increment OutDatagrams once per a datagram.
[IPV6]: Just increment OutDatagrams once per a datagram.
[IPV6]: Fix unbalanced socket reference with MSG_CONFIRM.
[NET_SCHED] protect action config/dump from irqs
[NET]: Fix two issues wrt. SO_BINDTODEVICE.
This patch adds missing pskb_may_pull calls to deal with non-linear
packets that may arrive from pppoe or pppol2tp.
It also copies cloned packets before writing over them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's rude to write over data that other people are still using. So call
skb_cow_head before PPP proceeds to modify the skb data.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an optimised version of skb_cow that avoids the copy if
the header can be modified even if the rest of the payload is cloned.
This can be used in encapsulating paths where we only need to modify the
header. As it is, this can be used in PPPOE and bridging.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the hdr variable (which is copied into the skb)
and instead sets the header directly in the skb.
It also uses __skb_push instead of skb_push since we've just checked
using skb_cow for enough head room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function __pppoe_xmit modifies the skb data and therefore it needs
to copy and skb data if it's cloned.
In fact, it currently allocates a new skb so that it can return 0 in
case of error without freeing the original skb. This is totally wrong
because returning zero is meant to indicate congestion whereupon pppoe
is supposed to wake up the upper layer once the congestion subsides.
This makes sense for ppp_async and ppp_sync but is out-of-place for
pppoe. This patch makes it always return 1 and free the skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_unshare_check call needs to be made before pskb_may_pull,
not after.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reevaluate C/P/T states when a cpu becomes online. This avoids
the caching of the broadcast information in the clockevents layer.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
drivers/net/pcmcia/3c589_cs: fix port configuration switcheroo
sk98lin: resurrect driver
ucc_geth: fix compilation
mv643xx_eth: Fix tx_bytes stats calculation
As struct iw_point is bi-directional payload, we should copy back the content
[PATCH] bcm43xx: Fix cancellation of work queue crashes
spidernet: fix interrupt reason recognition
ehea: fix last_rx update
ehea: propagate physical port state
Fix a lock problem in generic phy code
sky2: restore multicast list on resume and other ops
atl1: disable broken 64-bit DMA
This reverts commit e1abecc489.
The driver works on some hardware that skge doesn't handle yet.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently qe_bd_t is used in the macro call -- dma_unmap_single,
which is a no-op on PPC32, thus error is hidden today. Starting
with 2.6.24, macro will be replaced by the empty static function,
and erroneous use of qe_bd_t will trigger compilation error.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Guards around TIOCSLCKTRMIOS and TIOCGLCKTRMIOS.
Several architectures are still broken. Put temporary-for-2.6.23 ifdef guards
around the offending code.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by:: Linus Torvalds <torvalds@linux-foundation.org>
A guest context switch to an uncached cr3 can require allocation of
shadow pages, but we only recycle shadow pages in kvm_mmu_page_fault().
Move shadow page recycling to mmu_topup_memory_caches(), which is called
from both the page fault handler and from guest cr3 reload.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 02a5e0acb3 ("BLOCK: Hide the
contents of linux/bio.h if CONFIG_BLOCK=n") broke the kernel build for
the CONFIG_COMPAT && !CONFIG_BLOCK case:
CC fs/compat_ioctl.o
In file included from include/linux/raid/md_k.h:19,
from include/linux/raid/md.h:54,
from fs/compat_ioctl.c:25:
include/linux/raid/../../../drivers/md/dm-bio-list.h: In bio_list_:
include/linux/raid/../../../drivers/md/dm-bio-list.h:40: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h: In bio_list_:
include/linux/raid/../../../drivers/md/dm-bio-list.h:48: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h:51: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h: In bio_list_:
include/linux/raid/../../../drivers/md/dm-bio-list.h:64: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h: In bio_list_merge_:
include/linux/raid/../../../drivers/md/dm-bio-list.h:78: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h: In bio_list_:
include/linux/raid/../../../drivers/md/dm-bio-list.h:90: error: dereferencing pointer to incomplete type
include/linux/raid/../../../drivers/md/dm-bio-list.h:94: error: dereferencing pointer to incomplete type
make[1]: *** [fs/compat_ioctl.o] Error 1
make: *** [fs] Error 2
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A crash upon booting that is caused by bcm43xx has been reported [1] and
found to be due to a work queue being reinitialized while work on that
queue is still pending. This fix modifies the shutdown of work queues and
prevents periodic work from being requeued during shutdown. With this patch,
no more crashes on reboot were observed by the original reporter. I do not
get that particular failure on my system; however, when running a large
number of ifdown/ifup sequences, my system would kernel panic with the
'caps lock' light blinking at roughly a 1 Hz rate. In addition, there were
infrequent failures in the firmware that resulted in 'IRQ READY TIMEOUT'
errors. With this patch, no more of the first type of failure occur, and
incidence of the second type is greatly reduced.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=8937
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug: With a hardware encoder board installed as cx88[1] and a
non-encoder boards installed as cx88[0], an OOPS is generated
during cx8802_get_device() called from mpeg_open().
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7191.c: In function 'saa7191_probe':
saa7191.c:596: warning: passing argument 3 of
'saa7191_write_block' discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 85237f202d introduced the
following warning (with CONFIG_USB_PWC_DEBUG=y):
drivers/media/video/pwc/pwc-if.c: In function "pwc_video_close":
drivers/media/video/pwc/pwc-if.c:1211: warning: "i" may be used uninitialized in this function
This is true, and can cause a broken debug message to be logged.
Here's a fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now the composite sound input doesn't work on AverTV 307 because of
the wrong mux setup. The composite sound is routed via an external
4channel multiplexer controlled by GPIO, while the code assumes an internal
multiplexer instead.
Presumably this was a copy/paste error, and noone have ever tested the
functionality.
With the attached patch it works properly, which gives me an ability to
finally watch the cable TV under linux.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a documentation bug (the type mask is 3 bits long, not 2) the wrong
frame types were filled in: the B and P frame types were swapped.
This bug also hid a second bug: when a capture is stopped a last entry is
written into the pgm index buffer with internal type 0, denoting the end
of the program. This entry wasn't ignored, instead it was accidentally
returned to the caller as a P frame.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This fixes a problem introduced with commit
b5f2f4d1a6
The commit added a wrong chip definition to radeonfb which causes
a blank console on my Laptop if radeonfb is loaded.
The patch
- renames PCI_CHIP_RS485_5975 to PCI_CHIP_RS482_5975
- corrects the chip family (RS480 instead of R300) for 0x5975
- ensures that PCI IDs are in ascending order in ati_ids.h
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Tentatively-acked-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As observed with various Radeon X300 cards console goes blank
without that fix.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8dfe4b1486.
There are a number of issues still remaining in usb-storage autosuspend,
so, to be safe, we need to revert this for now.
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as965) disables autosuspend by default for all USB devices
other than hubs. We are seeing too many devices that can't suspend or
resume properly, the blacklist is growing unreasonably quickly, and
this sort of thing should be handled in userspace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch solves a problem that the spidernet driver sometimes fails
to handle IRQ.
The problem happens because,
- In Cell architecture, interrupts may arrive at an interrupt
controller, even if they are masked by the setting on registers of
devices. It happens when interrupt packets are sent just before
the interrupts are masked.
- spidernet interrupt handler compares interrupt reasons with
interrupt masks, so when such interrupts occurs, spidernet interrupt
handler returns IRQ_NONE.
- When all of interrupt handler return IRQ_NONE, linux kernel disables
the IRQ and it no longer delivers interrupts to the interrupt handlers.
spidernet doesn't work after above sequence, because it can't receive
interrupts.
This patch changes spidernet interrupt handler that it compares
interrupt reason with SPIDER_NET_INTX_MASK_VALUE.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update last_rx in registered device struct instead of
in the dummy device.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduces a module parameter to decide whether the physical
port link state is propagated to the network stack or not.
It makes sense not to take the physical port state into account
on machines with more logical partitions that communicate
with each other. This is always possible no matter what the physical
port state is. Thus eHEA can be considered as a switch there.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to restore multicast settings on resume and after 'ethtool -r'.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
64-bit DMA causes data corruption with atl1. We don't know why, and Atheros
is working on it. For now, just use 32-bit DMA. This is a big hack that is
probably wrong, but it stops the bleeding.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Acked-by: Chris Snook <csnook@redhat.com>
Acked-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One of the very first things lguest_init() does is a memcpy. On
Athlon/Duron/K7 or CyrixIII/VIA-C3 or Geode GX/LX, this tries to use
MMX.
memcpy -> _mmx_memcpy -> kernel_fpu_begin -> clts -> paravirt_ops.clts
But we haven't set paravirt_ops.clts yet, so we do the native version
and crash. The simplest solution is to use __memcpy.
Thanks to Michael Rasenberger for the bug report.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SERIAL_BFIN=m or SERIAL_MUX=m shouldn't allow SERIAL_CORE_CONSOLE=y.
Additionally, this patch fixes whitespace instead of tabs at the
SERIAL_MUX_CONSOLE option.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel framebuffer mis-calculated pixel clocks.
The pixel clock (and thus both H and V sync) will be slower than requested, so
if you set the minimum allowed the display may not sync. In case of really
old CRT display it could theoretically damage it.
I'm using it with PAL TV (using RGB input - SCART connector) and the bug
prevented it from working at all (TV requirements are more strict and made the
bug visible).
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
G33 has 1MB GTT table range. Fix GTT mapping in case like 512MB aperture
size.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
G33 GTT stolen memory is below graphics data stolen memory and be seperate,
so don't subtract it in stolen mem counting.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I ran into a few problems.
n_tty_ioctl() for instance:
drivers/char/tty_ioctl.c:799: error: $,1rxstruct termios$,1ry has no
member named $,1rxc_ispeed$,1ry
This is calling the copy interface that is supposed to be using
a termios2 when the new interfaces are defined, however:
case TIOCGLCKTRMIOS:
if (kernel_termios_to_user_termios((struct termios __user *)arg, real_tty->termios_locked))
return -EFAULT;
return 0;
This is going to write over the end of the userspace
structure by a few bytes, and wasn't caught by you yet
because the i386 implementation is simply copy_to_user()
which does zero type checking.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8942
Use PCI_DMA_* constants instead of own private definitions Fall back to
32-bit DMA mask if a 64-bit one fails
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Jeff Garzik <jeff@garzik.org>
Tested-by: Lars <polynomial-c@gmx.de>
Cc: Alessandro Polverini <alex@nibbles.it>
Cc: <dac@conglom-o.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent changed to raid5 to allow offload of parity calculation etc
introduced some bugs in the code for growing (i.e. adding a disk to) raid5
and raid6. This fixes them
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the quirk enables the SIR part of the SMCf010 device, the 8250 driver
may claim it as a legacy ttyS device, which makes the legacy probe in the
smsc-ircc2 driver fail.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the error code when dev0:fun1 was hidden by BIOS to one
more appropriate.
Signed-off-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When EDAC is configured for EDAC DEBUGGING, the debug printk output level
was set TOO high (EMERG). This patch brings it down to a DEBUG level
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it
only writes one zero filled word to the transmit register. If the driver
expects to receive more than one word it will wait forever for a second
receive interrupt. With this patch the controller will shift out zeroes
until all words have been received.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Port of Alan's patch for pata_via.c.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ensure that BLK_DEV_IDE is built-in before allowing BLK_DEV_IDE_PMAC to
be selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Bret Towe <magnade@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: irq and pci_ids patch for Intel Tolapai
PCI: unhide SMBus on Compaq Deskpro EP 401963-001 motherboard
PCI: Remove __devinit from pcibios_get_irq_routing_table
PCI: remove devinit from pci_read_bridge_bases
PCI AER: fix warnings when PCIEAER=n
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: drivers/usb/serial/bus.c: Fix incompatible pointer type warning
USB: another quirky device (LCD display)
USB: fix serial gadget ACM breakage
USB: More USB_QUIRK_RESET_RESUME devices
USB Mass Storage: limit "Rockchip ROCK MP3" device (071b:3203) max I/O to 64 sectors per command
USB: Nikon D40 Quirks
USB: Add Sony Ericsson P1i to unusual_devs.h
USB: option: Add Dell HSDPA 5520 to driver
USB: option: Add a new device ID for the HUAWEI E220 HSDPA modem.
USB: fix linked list insertion bugfix for usb core
USB: quirky flash drive
USB: prevent Genesys USB-IDE from autosuspending
USB: prevent Thomson card reader from autosuspending
USB: Add iPhone device id to the quirk list.
USB: ftdi_sio: add of a new product/manufacturer, TML
usb/misc/sisusbvga: add product ID of TARGUS/MCT device
USB: oti6858: Remove broken ioctl code in -mm tree and also the broken fixes
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type
Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Two of the CDC ACM control requests in the serial gadget have never
been correct, and have been reported to cause serious troubles ... as
in, soft lockup and maybe watchdog reset (depending on hardware).
This patch makes those request fail cleanly, rather than misbehaving.
Someone using CDC ACM should fix them according to the FIXME comments
which now replace the previous bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.
The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.
Typical kernel log showing the problem is:
usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6
This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
Signed-off-by: Massimiliano Ghilardi <massimiliano.ghilardi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The D40 needs the same quirks as the other (semi-)professional Nikon cameras.
The patch is against 2.6.23-rc5.
Details:
http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on information sent in by Christian Gothe.
Cc: Christian Gothe <christian.gothe@kapelan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.
Signed-off-by: Nathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That drive is quite odd. It has 2K sectors, times out getting string
descriptors and needs a quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as986) prevents the troublesome Genesys USB-IDE adapter
from autosuspending. It may not be necessary for all such devices,
but the one in Bugzilla #8892 sometimes fails to resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as985) prevents the SGS THomson Microelectronics 4in1 card
reader from autosuspending. This resolves Bugzilla #8885.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device is Targus ACP50US which includes a Magic Control Technologies
usb vga device using the SiS315(E) or compatible.
Signed-off-by: Samson Yeung <fragmede@onepatchdown.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This stuff is simply not needed.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[INET_DIAG]: Fix oops in netlink_rcv_skb
[IPv6]: Fix NULL pointer dereference in ip6_flush_pending_frames
[NETFILTER]: Fix/improve deadlock condition on module removal netfilter
[NETFILTER]: nf_conntrack_ipv4: fix "Frag of proto ..." messages
[NET] DOC: Update networking/multiqueue.txt with correct information.
[IPV6]: Freeing alive inet6 address
[DECNET]: Fix interface address listing regression.
[IPV4] devinet: show all addresses assigned to interface
[NET]: Do not dereference iov if length is zero
[TG3]: Workaround MSI bug on 5714/5780.
[Bluetooth] Fix parameter list for event filter command
[Bluetooth] Update security filter for Bluetooth 2.1
[Bluetooth] Add compat handling for timestamp structure
[Bluetooth] Add missing stat.byte_rx counter modification
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libiscsi: sync up iscsi and scsi eh's access to the connection
[SCSI] libiscsi: fix null ptr regression when aborting a command with data to transfer
[SCSI] qla2xxx: Update version number to 8.02.00-k3.
[SCSI] qla2xxx: Correct mailbox register dump for FWI2 capable ISPs.
[SCSI] qla2xxx: Correct 8GB iIDMA support.
[SCSI] qla2xxx: Correct management-server login-state synchronization issue.
[SCSI] qla2xxx: Don't modify parity bits during ISP25XX restart.
[SCSI] qla2xxx: Allocate enough space for the full PCI descriptor.
[SCSI] zfcp: fix the data buffer accessor patch
[SCSI] zfcp: allocate gid_pn_data objects from gid_pn_cache
[SCSI] zfcp: fix memory leak
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>