MTD NAND partition for file-system should start at offset=0xA00000
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7xx platform has in-build GPMC and ELM h/w engines which can be used
for accessing externel NAND flash device. This patch:
- adds generic DT binding in dra7.dtsi for enabling GPMC and ELM h/w engines
- adds DT binding for Micron NAND Flash (MT29F2G16AADWP) present on dra7-evm
*Important*
On DRA7 EVM, GPMC_WPN and NAND_BOOTn are controlled by DIP switch
So following board settings are required for NAND device detection:
SW5.9 (GPMC_WPN) = LOW
SW5.1 (NAND_BOOTn) = HIGH
Signed-off-by: Minal Shah <minalkshah@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW ethernet support for AM437x GP EVM which has one slave pinned out
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add cpsw phy sel device tree node for selecting phy mode in control module
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both the VAR-STK-OM44 and VAR-DVK-OM44 boards comes with the
WLAN/BT version of the system on module VAR-SOM-OM44.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for VAR-SOM-OM44[1] SODIMM system on module from
Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet
(LAN7500) and optional WLAN/BT.
Also add support for VAR-STK-OM44 development board from
Variscite. This kit features a VAR-SOM-OM44 and the carrier board
VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as
VAR-DVK-OM44 but without the LCD display.
omap4-var-stk-om44.dts replace the old and very limited
omap4-var-som.dts.
[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboard
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4/5 TRMs primarily list address offsets from the padconf
physical address (which is not driver base address) and not
always the absolute physical address for padconf registers like
some other OMAP TRMs. So create a new macro to use this offset
and to avoid confusion between different OMAP parts.
For more information, see the tables in TRM for named something like
"Device Core Control Module Pad Configuration Register Fields"
and "Device Wake-Up Control Module Pad Configuration Register Fields"
Note that we now also have to update cm-t54 for the fixed up
offsets.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated comments, updated cm-t54]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB pinmux information and USB modes
for the USB controllers.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for the Super Speed USB controllers, omap-control-usb,
USB2 PHY and USB3 PHY devices.
Remove ocp2scp1 address space from hwmod data as it is
now provided via device tree.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This clock gate description is missing in the older Reference manuals.
It is present on the SoC to provide 960MHz reference clock to the
internal USB PHYs.
Reference: DRA75x_DRA74x_ES1.1_NDA_TRM_vO.pdf, pg. 900,
Table 3-812. CM_COREAON_L3INIT_60M_GFCLK_CLKCTRL
Use l3init_960m_gfclk as parent of usb_otg_ss1_refclk960m and
usb_otg_ss2_refclk960m.
CC: Benoît Cousson <bcousson@baylibre.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB2 PHY driver expects named clocks for wakeup clock
and reference clock. Provide this information for USB2 PHY
nodes in OMAP4 and OMAP5 SoC DTS.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.
[Roger Q] Clean up. Updated IRQ for interrupt crossbar.
CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for sata.
[Roger Q] Clean up.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the comments, LCD pins 16-23 were numbered in the wrong order.
Fix this and use proper pinmux constants for all entries while we
are at it.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Benoit Parrot <bparrot@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use MATRIX_KEY macro from dt-bindings/input/input.h
to make the keyboard matrix human readable.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These add device tree entry for qspi controller driver on dra7-evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am437x-gp-evm is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add touchscreen support for AM437x GP EVM using pixcir
touchscreen controller.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixup Y resolution and add default pin state. Also update
the compatible id.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA722 is part of DRA72x family which are single core cortex A15 devices
with most infrastructure IPs otherwise same as whats on the DRA74x family.
So move the cpu nodes into dra74x.dtsi and dra72x.dtsi respectively.
Also add a minimal dra72-evm dts file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: linux-doc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>
"ti,dra752" is neither documented nor correct, since the device is actually a
dra742 device as rightly documented in dt bindings.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support of AW-NH387 (mwifiex) WiFi/BT chip connected to MMC3.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T54 CoM and SBC-T54 board:
http://compulab.co.il/products/computer-on-modules/cm-t54/http://compulab.co.il/products/sbcs/sbc-t54/
SBC-T54 is a single board computer based on OMAP5432 CPU.
It is implemented with a CM-T54 CoM providing most of the functions,
and SB-T54 carrier board providing connectors and several additional
functions.
Added basic support for:
* PMIC
* LED
* MMC/SD
* eMMC
* USB
* I2C1/4
* SB-T54 and CM-T54 EEPROMs
* RTC
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Expose the PMU on OMAP5.
Tested with perf on OMAP5 uEVM.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The N950/N9 uses two additional regulators from the twl 4030 for CSI-2
receiver (vaux2) and cameras (vaux3).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the Nokia N900's sound
system.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add madc node to twl4030, so that board DTS
files can simply reference the A/D converter.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree support for the wireless chip
built into the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am43x-epos-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am437x-gp-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for 2 instances each of
- ocp2scp
- USB PHY control module
- USB PHY
- dwc3_omap
- USB
for AM43xx.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB and USB PHY reference clock data
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: tabified]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With ARCH_OMAP2PLUS being separated out into OMAP2/3/4/5 etc all the TI device
tree blobs are built no matter the combination of SoCs that are enabled. This
often causes a bunch of irrelevant .dts to be built on a multi platform kernel,
this enables the building of just the ones relevant to the SoCs that are
actually enabled. It also orders the dts file alphabetically.
This also helps to avoid trivial merge conflicts when adding support
for new boards.
[tony@atomide.com: updated the order for am335x and am43x, moved am3517 to omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that is
not available at device creation time. This is a problem causing
mainline to fail on a number of ARM platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B2JT
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bug fixes from Grant Likely:
"These are some important bug fixes that need to get into v3.15.
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common
usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that
is not available at device creation time. This is a problem
causing mainline to fail on a number of ARM platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: do irq resolution in platform_get_irq
of: selftest: add deferred probe interrupt test
dt: Fix binding typos in clock-names and interrupt-names
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTWTroAAoJEL9jRaJfXa5PHMkIAJB2S6zuqIxn7qRsfeD5YauR
nz7AHjDaakoVy6YTaMdHQI+dXSK6BPUNvMbrKzW3WWbT4ktJ/r3k/OeeBv/2T93L
8KW1Bbif7kPfdfITwCCWDs5waTDVXSBC6AGGoXomzQIt4MqghhzoLRc6uvhnuYAL
R7ZJsTWRa+47LVOJsghVffMyNlwCMj//prW7PBY6RIZXhpcbI+FGYv5Rm1XRITWn
uL2cSulBmWeqMVCR/gFx8/K5TqZ90q835dD1Ggh+BeB1Vaifu9/cI3D8w0hl/xy9
nRneKdTaTEpKjgwI3up4vMFbLbMI7brdMphZ9ZeGgK+YuWXFDbKvvdwjvDJ4Tx0=
=BS4Q
-----END PGP SIGNATURE-----
Merge tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
ARM Versatile Express fixes for 3.15
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
* tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
Includes an update to 3.15-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=co/l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ANme
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
