Preparation for code re-use. Also use ioread/write
wrappers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's impossible to rely on disable_irq() and/or CE
interrupt masking with legacy shared interrupts.
Other devices sharing the same irq line may assert
it while ath10k is doing something that requires
no interrupts.
Irq handlers are now registered after all
preparations are complete so spurious/foreign
interrupts won't do any harm. The handlers are
unregistered when no interrupts are required (i.e.
during driver teardown).
This also removes the ability to receive FW early
indication (since interrupts are not registered
until early boot is complete). This is not mission
critical (it's more of a hint that early boot
failed due to unexpected FW crash) and will be
re-added in a follow up patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function did a couple of things: it allocated
CE completions, registered CE callbacks and
enabled CE interrupts through HW registers.
This cannot be so. Split the function into one
that allocates CE completions and the other one
that starts off CE operation.
This is required for future legacy shared
interrupt handling.
This also fixes possible memory leak if post rx
failed.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary for interrupts to be
used for BMI. BMI already assumes there's only one
caller at a time and it works directly with CE.
Make BMI poll for CE completions instead of
waiting for interrupts. This makes disabling
interrupts during early boot possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware waits until host signals whether it has
chosen MSI(-X) or shared legacy interrupts. It is
not required for the driver to register interrupt
handlers immediately.
This patch prepares the pci irq code for more
changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k assumed all interrupts were directed to it.
This isn't the case for legacy shared interrupts.
ath10k consumed interrupts for other devices.
Check device irq status and return IRQ_NONE when
appropriate.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can show the same amount of information in one line. And then
it's easier to show this information only during first firmware boot
(see next patch).
For UART printouts there's already a message when they are enabled so
no need to have a print when they are disabled, that's the default
anyway.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Convert the MSI failure warnings to a debug message to make them less spammy.
Also convert the irq mode printout to a single print to make it easier to
show it only once.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.
By default radar detected event in not blocked.
To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure interface combination for AP running on channels
where radar detection is required. It allows only one type
of interface - AP on DFS channel and limits number of AP
interfaces to 8. Setup WMI channel flags accordingly to mac
channel configuration. CAC based on additional monitor vdev
is started if required for current channel.
kvalo: dropped ATH10K_DFS_CERTIFIED config option as this
the DFS still depends on few mac80211 and cfg80211 patches
which are on mac80211-next.git right now. The config option
will be added later once all dependencies are available.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Garbage was reported in ieee80211_tx_info. This
led to a WARN_ON in cfg80211_calculate_bitrate().
This also fixes some random tx bitrate values
reported through `iw` command.
Reported-By: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was obseverd many times the short queue limit can be
easily exceeded in case of AP multiple BSSID scenarios.
"ath10k: wmi mgmt_tx queue limit reached."
This was leading to TX packets drops.
This patch expands the queue limit to 128. After many stress
experiments (high traffic and lot of management frames in
the air) the new value seems to fix the problem on platforms
with limited resources.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With commit 0cfcefef1 ("mac80211: support reporting A-MSDU subframes
individually") there's no need to have the hack to clear the retry bit in
ath10k_htt_rx_amsdu(), mac80211 can handle this properly now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames were never retransmitted with
different/lower bandwidths, e.g. only 80MHz
bandwidth was used when dealing with a VHT80
peer.
Allow HW rate control to try out different
bandwidths when retransmitting. This increases
robustness.
Also, document the parameter properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HIF was not stopped properly in
ath10k_core_start() upon failure. This could cause
memory leaks of CE completions entries and
possibly other issues as well.
Move the HIF start/stop out of
ath10k_htc_wait_target(). The ctl_resp completion
is already prepared in ath10k_htc_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should make sure the device won't issue any
interrupts nor access any memory after the driver
is stopped/freed thus avoid memory corruption in
some cases.
Reported-By: Ben Greear <greearb@candelatech.com>
Reported-By: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing error reporting and adjust other
prints to make everything more consistent.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves irq registering after necessary
structures have been allocated and initialized.
This should prevent interrupts from causing
tasklet access invalid memory pointers.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware crashes it may report CE
completions for entries that were never
submitted/filled with meaningful data. This in
turn led to NULL dereferences.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This shouldn't be silenced. This will be necessary
for PCI init code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This removes some remaining direct use of the wake
register which could interfere with power state
tracking of the target device. This will allow
initialization code reordering.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check doesn't make much sense. If the address
were to be 0x0000 the check would fail. In this
case a 0 address isn't wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to put target back to sleep. This was a
minor issue as it didn't really matter if we put
target back to sleep at this point. It just looked
wrong.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE error interrupts were not disabled. This could
lead to invalid memory accesses / memory
corruption.
Also make sure CE watermark interrupts are also
disabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
What the function does is to actually wait for the
firmware indication bit to be set. Prerequisite
for this is having interrupts registered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function will soon be called from more than 1
place.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible for FW error tasklet to be
executed during teardown. This could lead to
system crashes and/or memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It wasn't really useful to have it to begin with.
This makes it a little simpler to re-arrange PCI
init code as some function depended on
ar_pci->ce_count being set.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not all errors were properly notified, fix that.
kvalo: use ath10k_warn() for all messages, cosmetic changes to some of the messages
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the 'ar' registration fails early, the debug
objects were not initialized, and trouble ensued when
the object was later destroyed and the un-initialized
objects were accessed.
Per Kalle's suggestion, move the debug_destroy to the
core_unregister method.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
memory is malloced in ath10k_pci_probe() and should be freed before
leaving from the error handling cases, otherwise it will cause
memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If beacon tx command failed the wmi command buffer
was not freed. This led to OOM in the long run.
This became aparent when stress testing
multi-BSSID.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sk_buff was not freed in some cases. The patch
unifies the msdu freeing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows txpower limits other than regulatory
to be applied (e.g. user txpower limit provided
via iw/nl80211).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was previously thought that FW expects tx power
in quarters of dBm.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be needed for proper support of (user)
configurable tx power level.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the creation fails, this keeps us from crashing later when
trying to do a list_del(arvif->list).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_wait() didn't notify any errors to callers, it
just printed a warning so add proper error handling. This fixes
a crash Ben reported:
ath10k: MSI-X interrupt handling (8 intrs)
ath10k: Unable to wakeup target
ath10k: target took longer 5000 us to wake up (awake count 1)
ath10k: Failed to get pcie state addr: -16
ath10k: early firmware event indicated
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci]
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.1.389 firmware has some differences in
calculation of number of outstanding HTT TX
completions. This led to FW crashes of 10.1.389
while main firmware branch was unnaffected.
The patch makes sure ath10k doesn't queue up more
MSDUs than it should.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware crashes during FW probing it would try
to perform FW recovery which uses mac80211
workqueue before registering to mac80211.
Using internal workqueue solves the problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NSTS values reported in the VHT-SIG-A1 are 0
through 7 but they actually describe number of
streams 1 through 8.
1SS frames were dropped. This patch fixes this.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes incorrect values being printed on
big-endian hosts.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a few checks and warnings to make it easier to
track any kind of monitor vdev mismanagement.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes issue with interface bridging.
Linux bridging sets promiscuous mode for all
interfaces that are in a bridge. This translates
to configure_filter() being called in a mac80211
driver.
Before the patch operational interface would be
started and upped again when promiscuous mode was
enabled causing all sorts of strange issues:
* no HTT RX happening (i.e. no traffic)
* FW crash upon driver reload/unload
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_cmd_send() will now sleep if there are no credits available.
To make it easier to catch callers in atomic context add might_sleep()
to the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_bss_assoc() was calling ath10k_peer_assoc(), which can sleep, under
atomic rcu_read_lock() and causing scheduing while atomic errors. Workaround
that by delaying the call to ath10k_wmi_peer_assoc().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 interface iteration functions that were
used originally iterated over interfaces that
weren't re-added to the driver during recovery.
Since internal vif list is now used it's safe to
remove the safe-guard as internal vif list is
based on add/remove_interface function which
guarantees that vdev is created in FW before it is
iterated over.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent HTC/WMI changes introduced the bug. ath10k
was using _atomic iteration function with
sleepable functions.
mac80211 provides another iteration function but
it cannot be safely called in hw_config() callback
due to local->iflist_mtx being possibly acquired
already.
The patch uses internal vif list for iteration
purposes and removes/refactors no longer necessary
_iter functions.
Reported-By: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 interface interations functions have
peculiar locking issues. This patch introduces
internal (to ath10k) vif list that will be used
for vif iteration purposes.
kvalo: remove extra INIT_LIST_HEAD()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If something failed along add_interface() setup it
was possible to leak a vdev id, vdev and peer.
This could end up with leaked FW state or FW crash
(assuming add_interface() failure wasn't a result of
a crash).
kvalo: rebased, whitespace fixes
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent WMI/HTC changes made it possible for WMI
commands to sleep (if there's not enough HTC TX
credits to submit a command). TX path is in an
atomic context so calling WMI commands in it is
wrong.
This simply moves WEP key index update to a worker
and fixes the 'scheduling while atomic' bug.
This still leaves multiple WEP key handling laggy,
i.e. some frames may be TXed with an old/different
key (although recipient should still be able to RX
them).
kvalo: changed the title
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return -EOPNOTSUPP if given parameter is not supported by firmware.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename WMI_CMD_UNDEFINED to WMI_CMD_UNSUPPORTED. This is more
accurate here. Also return -EOPNOTSUPP instead of -EINVAL in
wmi_cmd_send().
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware does not support WMI_VDEV_PARAM_TX_ENCAP_TYPE.
It's a known limitation and we should not warn about this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ath10k_debug_start() was not called with conf_mutex, fix that. Also there was a
deadlock in ath10k_debug_stop(), rename it to ath10k_debug_destroy() and call
it only when the device is destroyed.
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For VHT peers, the maximum A-MPDU size has to be calculated
from the VHT capabilities element and not the HT-cap. The formula
is the same, but a higher value is used in VHT, allowing larger
aggregates to be transmitted.
The patch contains a workaround for some Netgear/Linksys APs that
report Rx A-MPDU factor incorrectly.
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to oversight AP 10.X support was merged with
Ethernet RX decap mode.
Only Native Wifi RX decap mode guarantees IP
header is properly aligned and avoids sk_buff data
realignment (which is very expensive
performance-wise) in mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some failpaths did `return` instead of a `goto`
leaking requested firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
size_t corresponds to %zu not %d. Compiler was
complaining about it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The value provided by num_sends_allowed is now
derived from CE source ringbuffer state.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is completely pointless to keep this function
around. It doesn't do anything different than
ce_send except it introduces more overhead.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was observed few times, the artificial max_scan limit we
are using mainly to detect FW hangs, can be not enough for
instance while being associated and during heavy traffic.
What we do if the FW won't return with scan results within
the max_time time is a scan abort.
This is especially visible with 10.X fw which in combination
with dual band HW (scanning 32 channels) can end up with
hw_scan close to 10 seconds.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the WMI API has been added and we can detect from the
FW IEs what firmware variant we deal with, turn on support
for 10.x firmware branch in ath10k_wmi_attach().
kvalo: improve the commit log
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the appropriate define instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Noticed-by: Julia Lawall <julia.lawall@lip6.fr> via spatch script
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware IE containers can dynamically provide various information what
firmware supports. Also it can embed more than one image so updating firmware
is easy, user just needs to update one file in /lib/firmware/.
The firmware API 2 or higher will use the IE container format, the current API
1 will not use the new format but it still is supported for some time. FW API 2
files are named as firmware-2.bin (which contains both firmware and otp images)
and API 1 files are firmware.bin and otp.bin.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wmi_start_scan_cmd has an extra filed in our main
firmware track, reflact that to not have a mismatch in
case of 10.x track.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done exactly the same way as for vdev.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both firmwares (main and 10.x) have different set of vdev
parameters. To stay in sync with FW API, this patch introduces
a dynamic registering method.
ath10k_wmi_vdev_set_param() takes now indirect u32 value
to identify the Vdev parameter it want's to set.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce all TARGET specific values for 10.x firmware.
Some of them are common for both firmwares we will support,
but to avoid confusion, define everything with prefix 10X_.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to API differences in initialization structures for
main and 10.x firmwares we need to split the wmi_init_cmd
and wmi_resource_config structures.
This will be usefull also when setting the correct TARGET values,
like: number of peers, vdevs, pdevs etc.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is still the only way to submit mgmt frames in case
of 10.X firmware.
This patch introduces wmi_mgmt_tx queue, because of the
fact WMI command can block. This is a problem for
ath10k_tx_htt(), since it's called from atomic context.
The skb queue and worker are introduced to move the mgmt
frame handling out of .tx callback context and not block.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware can request a memory pool from host to offload
it's own resources. This is a feature designed especially
for AP mode where the target has to deal with large number
of peers.
So we allocate and map a consistent DMA memory which FW can
use to store e.g. peer rate contol maps.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was corrupted and leading to compilation warning
core.c: In function 'ath10k_check_fw_version':
core.c:79: warning: comparison is always true due to limited range of data type
Since we are going to support new FW track in the driver,
the sanity check for fw version number would be an overkill
then. This is just for information purposes anyway.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the both firmwares we are going to support,
have significantly different APIs (WMI and shared
structures), it's easier to actually split the whole
event handling functions, instead cutting them inside.
The fork starts now on ath10k_wmi_process_rx().
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We still use the same function handlers for both main and 10.X
paths. Next step is to track down and make the split needed.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will show and make it easier to track the API
differences in the new AP firmware.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce the cmd and events definitions for 10.X FW API
and make up the wmi_10x_cmd_map. This is the core of
host-firmware WMI interface for 10.X FW branch.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is the initial framework to implement dynamic
WMI API in order to support new firmware (from so
called 10.X branch)
The realization is to have a static WMI cmd map for
each of the firmwares, registered upom wmi init.
This patch creates such map for MAIN FW, updates
wmi_cmd_send() calls to take as a parameter
the map value instead of direct WMI enum.
As soon as complete 10.X API will be on place,
we will introduce the FW IE mechanics to dynamicaly
identify which FW is being used and based on that
we will use correct map, API, structures, etc.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following sequence causes FW crash:
-monitor vdev up,
-monitor vdev stop,
-monitor vdev delete.
Making monitor vdev down before stoping it works ok:
-monitor vdev up,
-monitor vdev down,
-monitor vdev stop,
-monitor vdev delete.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This starves FW RX ring buffer in case of
excessive RX. This prevents from CPU being
overwhelmed by RX indications/completions by
naturally forbiddin FW to submit more RX.
This fixes RX starvation on slow machines when
under heavy RX traffic.
kvalo: remove extra newline
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ethernet-like decapping mode leaves IP protocol
frame not aligned to 4-byte boundaries. This leads
to re-aligning in mac80211 which in turn leads to
poor CPU cache behaviour on some machines.
Since HW doesn't allow to change payload offset
properly the solution is to force HW to decap in
Native Wifi mode which always has 24-bytes long
802.11 header (even for QoS frames). This means IP
frame is properly aligned in this decap mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
NWifi decap mode always reports 802.11 Data
Frames, even when QoS Data Frames are actually
received.
This made mac80211 not report frame priority
properly (since there was no QoS Control field).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplify decapping code and make it easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Clarify how each decap mode works in one place.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW reports each A-MSDU subframe as a separate
sk_buff. It is impossible to configure it to
behave differently.
Until now ath10k was reconstructing A-MSDUs from
subframes which involved a lot of memory
operations. This proved to be a significant
contributor to degraded RX performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Instead of allocating sk_buff for a mere 16-byte
tx fragment list buffer use headroom of the
original msdu sk_buff.
This decreases CPU cache pressure and improves
performance.
Measured improvement on AP135 is 560mbps ->
590mbps of UDP TX briding traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use a saner goto scheme for failure handling. Also
group operations more sensibly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now the all MSDU transfer related structures
were freed when all resources were unreferenced.
Now HTC transfer is freed independently and HTT
transfer is so too.
This yields a way more simpler ath10k_skb_cb and
should possibly enable parallel pipe processing
(which is now serialized in
ath10k_pci_process_ce routine).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces number of memory accesses and
hopefully contributes to better performance in the
future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's more efficient to simply check num_pending_tx
value instead of traversing whole bitmap of
msdu ids.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit e9bb0aa39 ("ath10k: delete struct ce_sendlist") broke
num_sends_allowed incrementing. num_sends_allowed
exceeded initial values and could overflow.
This code was supposed to replenish
num_sends_allowed for partial sendlist items (i.e.
before final sendlist item from a sendlist was
completed and could be processed by completion
handlers).
Fortunately it seems it did not cause any major breakage,
yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit be8b394390 ("ath10k: make WMI commands block by design") broke
the build if CONFIG_ATH10K_TRACING was enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to have this processed
in a worker. There are no sleepable calls (and
actually shouldn't be).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is no longer used nor necessary since WMI
commands can block.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch prevents beacon misses in some case of
heavy load on a system.
If a beacon can't be transmitted directly from an
SWBA event it will be left in arvif->beacon and
transmission will be retried once TX credits
become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch removes HTC endpoint tx workers in
favour of direct command submission. This makes a
lot more sense for data path.
mac80211 queues are effectively stopped/woken up
in a more timely fashion preventing build up of
frames. It's possible to push more traffic than
the device/system is able to handle and have no
hiccups or performance degradation with UDP
traffic.
WMI commands will now report errors properly and
possibly block as they actively can wait for tx
credits to become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be necessary for further changes in
command submission scheme.
Once HTC is cleaned up WMI commands will finally
block.
This requires for SWBA to be processed in a
non-atomic context for now. Once other necessary
changes are in this will be reverted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will allow higher layers to anticipate and
act upon TX credits renewal. This will be
important for some future rework of WMI command
submission.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Credit calculation was overly complex
unnecessarily. Now skb dequeing is more unified.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
struct ce_sendlist is useless as we always add just one buffer onto it.
And most importantly, it's ugly as it doesn't use skb properly.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The peer PHY mode for 11ac operation needs to be determined
properly based on the channel bandwidth being used. Fix
this so that the proper mode is given to the firmware.
kvalo: earlier we used 11na-ht20 in STA mode for 11ac AP peer, this
patch changes that to 11ac-vht80. I didn't notice any change in
throughput in my tests, but nevertheless it's the right thing
to do.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just to unify with the rest of debug messages. Minimal functional changes,
only major ones are removal of the awkward "else" style in debug
messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix them to follow the general logging style in ath10k.
While at it, add print id chip_id to the debug log.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
core.c mostly deals with driver and firmware starting related
actions. And we can use the boot level also in other components,
like PCI and HTT.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise if CONFIG_ATH10K_DEBUGFS won't be set we will
end up with multiple definitions and compilation failure
in each place the header is included.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The double while() could end up running forever.
Inner while() would complete very fast. However
the completion processing could take enough time
for more completions to flow in. In that case the
outer while() would not terminate and run again,
and again. This could happen especially on a slow
host system.
This could lead to a system freeze during heavy
traffic. Note: this doesn't solve all known
starvation issues yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no functional changes. Just a small cleanup.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When configuring the host_interests over BMI, set the UART
baud rate to 19200. This is valid for QCA988X_2.0 devices.
kvalo: found during code review, there should not be any functionality
changes
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The indentation here implies this was meant to be
a multi-statement if, but it lacks the braces.
kvalo: add "ath10k: " prefix
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.
To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:
[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95
Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_ce_init() and the functions it calls wakeup
the chip multiple times. Simplify that to call
ath10k_pci_wake() only once. This also makes it
easier to add error handling when wakeup fails.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We should not try to access hw if wakeup fails so add
proper error checking for that. Also add the timeout lenght
to the warning message.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some parameters were unused and are not required.
They have no representation in firmware. Clean
them up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was only written to and never read back. No use
to keep it around.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New firmware comes with new HTT protocol version.
In 3.0 the separate mgmt tx command has been
removed. All traffic is to be pushed through data
tx (tx_frm) command with a twist - FW seems to not
be able (yet?) to access tx fragment table so for
manamgement frames frame pointer is passed
directly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mgmt_rx event structure has been expanded.
Since the structure header is expanded the payload
(i.e. mgmt frame) is shifted by a few bytes. This
needs to be taken into account in order to support
both old and new firmware.
This introduces a fw_features to keep track of any
FW-related ABI/behaviour changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WEP encoding was not working properly for AP and IBSS mode.
TX frames were encrypted with default WEP tx key index set
always to zero, what sometimes was wrong when different
key index should be used. This patch allows to update
WEP key index also for AP and IBSS mode.
Problem detected during automated WEP tests.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There was a possible memory leak when WMI command
queue reached it's limit. Command buffers were not
freed.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This enables driver to rx another decapped a-msdu
frames. It should possibly help with throughputs
in some cases and reduce (or eliminate) number of
messages like this:
ath10k: error processing msdus -524
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The "disable credit flow" flag was set too late
and it never was in the HTC service request
message.
This patch prevents firmware from reporting
(useless) HTC credits for HTT service. HTT service
doesn't use nor need credits.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it possible to see the reason why the
setup fails. It also adheres to code style of
error checking in ath drivers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Improve code readability by using enum and a
switch-case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes checkpatch warning from the latest
3.11-rc kernel tree.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove useless code that was causing WARN_ON when
a 80MHz+ vif entered promiscuous mode or monitor
interface was started.
The channel mode is already computed by
chan_to_phymode().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle pci_alloc_consistent(), kmalloc()
errors in copy engine module.
Found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The latest supported and available FW build is 1.0.0.636.
Reflect this in ath10k code.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the firmware support is no longer available for hw1.0,
drop all code (especially workarounds) for those units.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setup UAPSD peer/peer rate flags correctly.
WMI_RC_UAPSD_FLAG is a peer rate capabilities flag
and should not be set as a peer flag.
Found during code review, doesn't fix a known
issues.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Unify the PCI options location.
By default the SoC PS option is disabled to boost the
performance and due to poor stability on early HW revisions.
In future we can remove the module parameter and turn on/off
the PS for given hardware.
This change also makes the pci module parameter for SoC PS static.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes interrupt-related issue when no
interfaces were running thus the device was
considered powered down.
The power_down() function isn't really powering
down the device. It simply assumed it won't
interrupt. This wasn't true in some cases and
could lead to paging failures upon FW indication
interrupt (i.e. FW crash) because some structures
aren't allocated in that device state.
One reason for that was that ar_pci->started
wasn't reset. The other is interrupts should've
been masked when teardown starts.
The patch reorganized interrupt setup and makes
sure ar_pci->started is reset accordingly.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
pci_disable_msi() must be called if the initial
request_irq() fails.
Also add a warning message so it's possible to
distinguish request_irq() failure and
pci_enable_msi() failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The private memory area in vif provided by
mac80211 isn't guaranteed to be zeroed.
This patch should fix issues when switching
between STA and AP interface types.
The tim_bitmap could become polluted by STA bssid
field (since it's a union), wep_keys array
could also become polluted with invalid pointers
and probably much more.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently the available firmware has a limit of
handling 7 APs, 3 GOs or 8 STAs. This is based on
empirical tests and it is still possible some
combinations may crash the firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Normally user specifies broadcast ssid for
scanning. If the user wants to do a passive scan
it does not pass any ssids.
The patch makes sure we ath10k tells firmware to
not send anything at all in case it decides no
ssids equals broadcast ssid.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the device is removed and hotplug fails
ioread32() will return 0xFFFFFFFF. In that case
reading ringbuffer during device bringup led to
out-of-bounds addressing of a ringbuffer array
that in turn led to a paging failure.
This could be reproduced by the following:
* boot without acpi/prevent hotplug from working
* insert and manually detect (pci rescan) the device
* remove the device physically
* load ath10k driver
* kernel crashed
Ringbuffer index reading is now protected by using
an appropriate mask to prevent addressing an
invalid array index.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This implements a limited subset of what can be
reported in the survey dump.
This can be used for assessing approximate channel
load, e.g. for automatic channel selection.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW supports L3/L4 tx checksum offloading.
This should reduce CPU load and improve
performance on slow host machines.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HW supports L3/L4 rx checksum offloading.
This should reduce CPU load and improve
performance on slow host machines.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now ath10k assumed 3 spatial streams.
However some devices support only 2 spatial
streams.
This patch improves performance on devices that
don't support 3 spatial streams.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is more efficient to move just the 802.11
header instead of the whole payload in most cases.
This has no measurable effect on modern hardware.
It should improve performance by a few percent on
hardware such as an Access Point that have a slow
CPU compared to a typical desktop CPU.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If RTS and fragmentation threshold values are
0xFFFFFFFF they should be considered disabled and
no min/max limits must be applied.
This fixes some issues with throughput issues,
especially with VHT.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases channel arrays were never freed.
The patch also unifies error handling in the mac
setup function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Endpoints are re-initialized upon HTC start anyway
so there's no need to do that twice in case of
restarting HTC (i.e. in case of hardware
recovery).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to submit new HTC commands
after/while HTC stopped. This led to memory
corruption in some rare cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing. To perform a
forced firmware crash write 'crash' to
'simulate_fw_crash' debugfs file. E.g.
echo crash > /sys/kernel/debug/ieee80211/phy1/ath10k/simulate_fw_crash
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx processing functions dereference vif and caused
NULL to be dereferenced for injected frames.
Don't call these functions at all for injected
frames. It doesn't make much sense to do so
anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful to test FW crash handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Restart the hardware if FW crashes.
If FW crashes during recovery we leave the
hardware in a "wedged" state to avoid recursive
recoveries.
When in "wedged" state userspace may bring
interfaces down (to issue stop()) and then bring
one interface (to issue start()) to reload
hardware manually.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the device is not running then there may be no
FW at all to send the query to. If the FW is
already there it might still trigger a crash if
the command is sent before the device is fully
initialized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different FW versions may provide different
functions thus mean different hw capabilities
advertised to mac80211.
It is safe to swap firmware files on disk during
driver/device runtime without worries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes suspend-to-disk. The hardware is now
re-initialized upon freeze/thaw properly.
This also makes suspend/resume re-initialize the
hardware as WoWLAN support is not done yet.
With some little work it should be possible to
support hw reconfiguration for hw/fw recovery.
HW must be initialized once before registering to
mac80211 because FW determinates what hw
capabilities can be advertised.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary for proper hw reconfiguration
and to avoid memory leaks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary for hw reconfiguration to work.
Since mac80211 is not calling remove_interface()
is such case we must reset free_vdev_map.
Also use a define instead of a hardcoded value for
vdev map initialization.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split up fw-related and hw-related suspension code.
Although we don't advertise WoW support to
mac80211 yet it's useful to keep the code in
suspend/resume hooks.
At this point there's no need to keep pci pm ops.
In case of WoW mac80211 calls ath10k_suspend()
which should take care of entering low-power mode.
In case WoW is not available mac80211 will go
through regular interface teradown and use start/stop.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary if we want to be able to restart
hw on-the-fly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain notification hook can be called
regardless of the hw state (i.e. before start
mac80211 callback).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enables code reuse for proper hw reconfiguration
that is in turn required for proper
suspend/hibernation/wowlan support.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
