intel_plane->obj is not used anymore so kill it. Also don't pass both
the fb and obj to the sprite .update_plane() hook, as just passing the fb
is enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The problem is we're going to switch to a new context, which could be
the default context. The plan was to use restore inhibit, which would be
fine, except if we are using dynamic page tables (which we will). If we
use dynamic page tables and we don't load new page tables, the previous
page tables might go away, and future operations will fault.
CTXA runs.
switch to default, restore inhibit
CTXA dies and has its address space taken away.
Run CTXB, tries to save using the context A's address space - this
fails.
The general solution is to make sure every context has it's own state,
and its own address space. For cases when we must restore inhibit, first
thing we do is load a valid address space. I thought this would be
enough, but apparently there are references within the context itself
which will refer to the old address space - therefore, we also must
reinitialize.
v2: to->ppgtt is only valid in full ppgtt.
v3: Rebased.
v4: Make post PDP update clearer.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch was formerly known as, "Force pd restore when PDEs change,
gen6-7." I had to change the name because it is needed for GEN8 too.
The real issue this is trying to solve is when a new object is mapped
into the current address space. The GPU does not snoop the new mapping
so we must do the gen specific action to reload the page tables.
GEN8 and GEN7 do differ in the way they load page tables for the RCS.
GEN8 does so with the context restore, while GEN7 requires the proper
load commands in the command streamer. Non-render is similar for both.
Caveat for GEN7
The docs say you cannot change the PDEs of a currently running context.
We never map new PDEs of a running context, and expect them to be
present - so I think this is okay. (We can unmap, but this should also
be okay since we only unmap unreferenced objects that the GPU shouldn't
be tryingto va->pa xlate.) The MI_SET_CONTEXT command does have a flag
to signal that even if the context is the same, force a reload. It's
unclear exactly what this does, but I have a hunch it's the right thing
to do.
The logic assumes that we always emit a context switch after mapping new
PDEs, and before we submit a batch. This is the case today, and has been
the case since the inception of hardware contexts. A note in the comment
let's the user know.
It's not just for gen8. If the current context has mappings change, we
need a context reload to switch
v2: Rebased after ppgtt clean up patches. Split the warning for aliasing
and true ppgtt options. And do not break aliasing ppgtt, where to->ppgtt
is always null.
v3: Invalidate PPGTT TLBs inside alloc_va_range.
v4: Rename ppgtt_invalidate_tlbs to mark_tlbs_dirty and move
pd_dirty_rings from i915_address_space to i915_hw_ppgtt. Fixes when
neither ctx->ppgtt and aliasing_ppgtt exist.
v5: Removed references to teardown_va_range.
v6: Updated needs_pd_load_pre/post.
v7: Fix pd_dirty_rings check in needs_pd_load_post, and update/move
comment about updated PDEs to object_pin/bind (Mika).
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of implementing the full tracking + dynamic allocation, this
patch does a bit less than half of the work, by tracking and warning on
unexpected conditions. The tracking itself follows which PTEs within a
page table are currently being used for objects. The next patch will
modify this to actually allocate the page tables only when necessary.
With the current patch there isn't much in the way of making a gen
agnostic range allocation function. However, in the next patch we'll add
more specificity which makes having separate functions a bit easier to
manage.
One important change introduced here is that DMA mappings are
created/destroyed at the same page directories/tables are
allocated/deallocated.
Notice that aliasing PPGTT is not managed here. The patch which actually
begins dynamic allocation/teardown explains the reasoning for this.
v2: s/pdp.page_directory/pdp.page_directories
Make a scratch page allocation helper
v3: Rebase and expand commit message.
v4: Allocate required pagetables only when it is needed, _bind_to_vm
instead of bind_vma (Daniel).
v5: Rebased to remove the unnecessary noise in the diff, also:
- PDE mask is GEN agnostic, renamed GEN6_PDE_MASK to I915_PDE_MASK.
- Removed unnecessary checks in gen6_alloc_va_range.
- Changed map/unmap_px_single macros to use dma functions directly and
be part of a static inline function instead.
- Moved drm_device plumbing through page tables operation to its own
patch.
- Moved allocate/teardown_va_range calls until they are fully
implemented (in subsequent patch).
- Merged pt and scratch_pt unmap_and_free path.
- Moved scratch page allocator helper to the patch that will use it.
v6: Reduce complexity by not tearing down pagetables dynamically, the
same can be achieved while freeing empty vms. (Daniel)
v7: s/i915_dma_map_px_single/i915_dma_map_single
s/gen6_write_pdes/gen6_write_pde
Prevent a NULL case when only GGTT is available. (Mika)
v8: Rebased after s/page_tables/page_table/.
v9: Reworked i915_pte_index and i915_pte_count.
Also exercise bitmap allocation here (gen6_alloc_va_range) and fix
incorrect write_page_range in i915_gem_restore_gtt_mappings (Mika).
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v3+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Gen8, PDPs are saved and restored with legacy contexts (legacy contexts
only exist on the render ring). So change the ordering of LRI vs MI_SET_CONTEXT
for the initialization of the context. Also the only cases in which we
need to manually update the PDPs are when MI_RESTORE_INHIBIT has been
set in MI_SET_CONTEXT (i.e. when the context is not yet initialized or
it is the default context).
Legacy submission is not available post GEN8, so it isn't necessary to
add extra checks for newer generations.
v2: Use new functions to replace the logic right away (Daniel)
v3: Add missing pd load logic.
v4: Add warning in case pd_load_pre & pd_load_post are true, and add
missing trace_switch_mm. Cleaned up pd_load conditions. Add more
information about when is pd_load_post needed. (Mika)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes, but will improve code clarity and removed some
duplicated defines.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And remove one bogus * from i915_gem_gtt.c since that's not a
kerneldoc there.
v2: Review from Chris:
- Clarify memory space to better distinguish from address space.
- Add note that shrink doesn't guarantee the freed memory and that
users must fall back to shrink_all.
- Explain how pinning ties in with eviction/shrinker.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two code changes:
- Extract i915_gem_shrinker_init.
- Inline i915_gem_object_is_purgeable since we open-code it everywhere
else too.
This already has the benefit of pulling all the shrinker code
together, next patch adds a bit of kerneldoc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use both up/down manual ei calcuations for symmetry and greater
flexibility for reclocking, instead of faking the down interrupt based
on a fixed integer number of up interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite commit 31685c258e
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 3 17:33:01 2014 -0400
drm/i915/vlv: WA for Turbo and RC6 to work together.
Other than code clarity, the major improvement is to disable the extra
interrupts generated when idle. However, the reclocking remains rather
slow under the new manual regime, in particular it fails to downclock as
quickly as desired. The second major improvement is that for certain
workloads, like games, we need to combine render+media activity counters
as the work of displaying the frame is split across the engines and both
need to be taken into account when deciding the global GPU frequency as
memory cycles are shared.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we idle, we set the GPU frequency to the hardware minimum (not user
minimum). We introduce a new variable to distinguish between the
different roles, and to allow easy tuning of the idle frequency without
impacting over aspects of RPS. Setting the minimum frequency should be a
safety blanket as the pcu on the GPU should be power gating itself
anyway. However, in order for us to do set the absolute minimum
frequency, we need to relax a few of our assertions that we do not
exceed the user limits.
v2: Add idle_freq
v3: Init idle_freq for vlv and add a bunch of WARNs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the batch buffer is too large to fit into the aperture and we need a
GTT mapping for relocations, we currently fail. This only applies to a
subset of machines for a subset of environments, quite undesirable. We
can simply check after failing to insert the batch into the GTT as to
whether we only need a mappable binding for relocation and, if so, we can
revert to using a non-mappable binding and an alternate relocation
method. However, using relocate_entry_cpu() is excruciatingly slow for
large buffers on non-LLC as the entire buffer requires clflushing before
and after the relocation handling. Alternatively, we can implement a
third relocation method that only clflushes around the relocation entry.
This is still slower than updating through the GTT, so we prefer using
the GTT where possible, but is orders of magnitude faster as we
typically do not have to then clflush the entire buffer.
An alternative idea of using a temporary WC mapping of the backing store
is promising (it should be faster than using the GTT itself), but
requires fairly extensive arch/x86 support - along the lines of
kmap_atomic_prof_pfn() (which is not universally implemented even for
x86).
Testcase: igt/gem_exec_big #pnv,byt
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88392
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add a WARN_ONCE for the impossible reloc case and explain in
a short comment why we want to avoid ping-pong.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes the interface consistent to old i915_gem_obj_ggtt_pin.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the original code then if WARN_ON(i915_is_ggtt(vm) != !!ggtt_view)
was true then we leak "vma". Presumably that doesn't happen often but
static checkers complain and this bug is easy to fix.
Fixes: c3bbb6f2825d ('drm/i915: Do not use ggtt_view with (aliasing) PPGTT')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow for a larger receive data size, and check if the receiver returned
the number of bytes written. Without this, we've basically skipped all
the unwritten bytes for short writes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To keep things clear rename the intel_dp->supported_rates[] to
intel_dp->sink_rates[], and rename the supported_rates[] name we used
elsewhere for the intersection of source and sink rates to
common_rates[].
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TODO: Is there an actually nice way to print an array of ints?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"P1273_DPLL_Programming Spreadsheet.xlsm" lists a boatload of
frequencies for eDP. Try to use them all.
For now I've decided not to add hardcoded DPLL dividers for these cases
since chv_find_best_dpll() works just fine.
I've not actually tested any of these since I don't have an eDP 1.4 panel.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Complain loudly if we ever attempt to overflow the the supported_rates[]
array. This should never happen since the sink_rates[] array will always
be smaller or of equal size. But should someone change that we want to
catch it without scribblign over the stack.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that intel_dp_max_link_bw() no longer considers the source
restrictions we may try to enable MST with 5.4GHz even when the source
doesn't support it. To fix that switch the code over to handle the link
rate in the same way as the SST code handles it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the gen9 checks from the code and issue DP_LINK_RATE_SET whenever
the sink reports to support it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Consider the link rates reported by the sink via
DP_SUPPORTED_LINK_RATES when checking modes against the max link
rate.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp_compute_config() only really needs to know the rates supported
by both source and sink, so hide the raw source and sink arrays from it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the sink vs. source limit mess from intel_dp_max_link_bw() and
just move the source restriction checks to intel_dp_source_rates().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
[danvet: Resolve conflict with WaDisableHBR2:skl patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that both source and sink rates are always filled in there's no need
for any special cases in intel_supported_rates().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once we've read the rates from the sink we don't have to mess with them,
so the caller can just look at the stored rates without doing extra
copies. If the sink doesn't support the new link rate stuff, we just
point the caller at the default_rates[] array.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The source rates don't change, so we can just point the caller at the
const arrays.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in converting from hardware format every single time, just
store the rates in the final format under intel_dp.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in using uint32_t here, just plain old int will do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GGTT views are only applicable when dealing with GGTT. Change the code to
reject ggtt_view where it should not be used and require it when it should
be.
v2:
- Dropped _ppgtt_ infixes, allow both types to be passed
- Disregard other but normal views when no view is specified
- More checks that valid parameters are passed
- More readable error checking
v3:
- Prefer WARN_ONCE over BUG_ON when there is code path for failure
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop unecessary forward decl from earlier patch iterations.]
[danvet: Remove unused variable spotted by Tvrtko.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Regressed by this commit:
commit 3455454e18ca3f92c565700539e744c620d8276b
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Mar 3 15:21:56 2015 +0200
drm/i915: Add a for_each_intel_connector macro
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge because of numerous and interleaving conflicts and git
rerere getting confused a bit too often.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
All conflicts are because of -next patches backported to -fixes, so
just go with the code in -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We don't want to end up in a state where we track that the pipe has its
primary plane enabled when primary plane registers are programmed with
values that look possible but the plane actually disabled.
Refuse to read out the fb state when the primary plane isn't enabled.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reference: http://mid.gmane.org/20150203191507.GA2374@crion86
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
vmap_batch() calculates amount of needed pages for the mapping
we are going to create. And it uses this page count as an
argument for the for_each_sg_pages() macro. The macro takes the number
of sg list entities as an argument, not the page count. So we ended
up iterating through all the pages on the mapped object, corrupting
memory past the smaller pages[] array.
Fix this by bailing out when we have enough pages.
This regression has been introduced in
commit 17cabf571e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Jan 14 11:20:57 2015 +0000
drm/i915: Trim the command parser allocations
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setup new I915_GETPARAM ioctl entries for subslice total and
EU total. Userspace drivers need these values when constructing
GPGPU commands. This kernel query method is intended to replace
the PCI ID-based tables that userspace drivers currently maintain.
The kernel driver can employ fuse register reads as needed to
ensure the most accurate determination of GT config attributes.
This first became important with Cherryview in which the config
could differ between devices with the same PCI ID.
The kernel detection of these values is device-specific and not
included in this patch. Because zero is not a valid value for any of
these parameters, a value of zero is interpreted as unknown for the
device. Userspace drivers should continue to maintain ID-based tables
for older devices not supported by the new query method.
v2: Increment our I915_GETPARAM indices to fit after REVISION
which was merged ahead of us.
For: VIZ-4636
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Tested-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Acked-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as
commit c883ef1b1c
Author: Mika Kuoppala <miku@iki.fi>
Date: Tue Oct 28 17:32:30 2014 +0200
drm/i915: Redefine WARN_ON to include the condition
but for WARN_ON_ONCE. Since the kernel WARN_ON_ONCE actually picks up
*our* version of WARN_ON, we end up with messages like
[ 838.285319] WARN_ON(!__warned)
which are not that helpful.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV should be in a good enough shape now, so let's drop the
.is_preliminary flag.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We accidentally pass 'pipe' instead of 'port' to CHV_PLL_DW8() and
with PIPE_C we end up at register offset 0x8320 which isn't the
0x8020 we wanted. Fix it.
The problem was fortunately caught by the sanity check in vlv_dpio_read():
WARNING: CPU: 1 PID: 238 at ../drivers/gpu/drm/i915/intel_sideband.c:200 vlv_dpio_read+0x77/0x80 [i915]()
DPIO read pipe C reg 0x8320 == 0xffffffff
The problem got introduced with this commit:
commit 71af07f91f12bbab96335e202c82525d31680960
Author: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Date: Thu Mar 5 19:33:08 2015 +0530
drm/i915: Update prop, int co-eff and gain threshold for CHV
Cc: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignore the current state of the pipe and just check crtc_state->enable
and the number of FDI lanes required. This means we don't accidentally
mistake the FDI lanes as being available of one of the pipes just
happens to be disabled at the time of the check. Also we no longer
consider pipe C to require FDI lanes when it's driving the eDP
transcoder.
We also take the opportunity to make the code a bit nicer looking by
hiding the ugly bits in the new pipe_required_fdi_lanes() function.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logic in the FDI lane checks is very hard for my poor brain to
grasp. Rewrite it in a more straightforward way.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable the RPS interrupts programming(enable/disable/reset) for GEN9,
as missing changes to enable the RPS support on GEN9 have been added.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Earlier Turbo interrupts were not being processed for SKL,
as something was amiss in turbo programming for SKL.
Now missing changes have been added, so enabling the Turbo
interrupt processing for SKL.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added support for SKL in the i915_frequency_info debugfs function
v2:
- corrected the handling of reqf (Damien)
- Reorderd the platform check for cagf (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the global modeset resource function that would disable the
bifurcation bit, and instead enable/disable it when enabling the pch
transcoder. The mode set consistency check should prevent us from
disabling the bit if pipe C is enabled so the change should be safe.
Note that this doens't affect the logic that prevents the bit being
set while a pipe is active, since the patch retains the behavior of
only chaging the bit if necessary. Because of the checks during mode
set, the first change would necessarily happen with both pipes B and
C disabled, and any subsequent write would be skipped.
v2: Only change the bit during pch trancoder enable. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added support for SKL in the act_freq_mhz_show sysfs function
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL, GT frequency is programmed in units of 16.66 MHZ units compared
to 50 MHZ for older platforms. Also the time value specified for Up/Down EI &
Up/Down thresholds are expressed in units of 1.33 us, compared to 1.28
us for older platforms. So updated the gen9_enable_rps function as per that.
v2: Updated to use new macro GT_INTERVAL_FROM_US
v3: Removed the initial setup of certain registers, from gen9_enable_rps,
which gets overridden later from gen6_set_rps (Damien)
v4: Removed the enabling of rps interrupts, from gen9_enable_rps.
To be done from intel_gen6_powersave_work only, as done for other
platforms also.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RP Interrupt Up/Down Frequency Limits register (A014) definition
has changed for SKL. Updated the gen6_rps_limits function as per that
v2: Renamed the function to intel_rps_limits (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to SKL, the time period programmed in Up/Down EI & Up/Down
threshold registers was in units of 1.28 micro seconds. But for
SKL, the units have changed (1.333 micro seconds).
Have generalized the implementation of gen6_set_rps_thresholds function,
by removing the hard coding done in it as per 1.28 micro seconds.
v2: Renamed the local variables & removed superfluous comments (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL, the frequency is programmed differently in RPNSWREQ (A008)
register (from bits 23 to 31, compared to bits 24 to 31). So updated
the gen6_set_rps function, as per this change.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the frequency is specified in units of 16.66 MHZ, barring the
RP_STATE_CAP(0x5998) register, which still reports frequency in units
of 50 MHZ. So an extra conversion is required in gen6_init_rps_frequencies
function for SKL, to store the frequency values as per the actual hardware unit.
v2: Corrected the conversion from 50 to 16.66 MHZ (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL, frequency is specified in units of 16.66 MHZ.
Updated the intel_gpu_freq() and intel_freq_opecode() functions
to do the conversion appropriately.
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For SKL, register definition for RPNSWREQ (A008), RPSTAT1(A01C)
have changed slightly. Also on SKL, frequency is specified in
units of 16.66 MHZ, compared to 50 MHZ for most of the earlier
platforms and the time values are expressed in units of 1.33 us,
compared to 1.28 us for earlier platforms.
Added new macros for the aforementioned changes.
v2: Renamed the GT_FREQ_FROM_PERIOD macro to GT_INTERVAL_FROM_US (Damien)
v3: Removed the implicit use of dev_priv in GT_INTERVAL_FROM_US macro (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the FW_WM() macro from the VLV wm code to polish up the wm
code for older gmch platforms.
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrap the FW register value shift+mask operations into a macro to hide
the ugliness a bit. Also might avoid bugs due to typos.
Also rename all the primary/sprite plane low order bit masks to have the
_VLV suffix, so that we can use the FW_WM_VLV() macro instead of the
FW_WM() macro for them in a consistent manner. Cursor and all the high
order bits are left to use the FW_WM() macro as there's no real
confusion with them.
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plane->fb is not as reliable as plane->state->fb so let's convert
intel_plane_restore() over the the new way of thinking as well.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to go dig throguh intel_crtc->base.cursor when we already have
the same thing as 'plane' local variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are now called from the plane commit hooks, so they really need to
be fast or else we risk atomic update failures. So kill the debug prints
which are slowing things down massively.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Without this Dave's 32bit rhel compiler is annoyed. Don't ask me about
the exact rules for this stuff though, but this should be safe.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Current ILK-style watermark code assumes the primary plane and cursor
plane are always enabled. This assumption, along with the combination
of two independent commits that got merged at the same time, results in
a NULL dereference. The offending commits are:
commit fd2d61341bf39d1054256c07d6eddd624ebc4241
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Fri Feb 27 10:12:01 2015 -0800
drm/i915: Use plane->state->fb in watermark code (v2)
and
commit 0fda65680e
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Fri Feb 27 15:12:35 2015 +0000
drm/i915/skl: Update watermarks for Y tiling
The first commit causes us to use the FB from plane->state->fb rather
than the legacy plane->fb, which is updated a bit later in the process.
The second commit includes a change that now triggers watermark
reprogramming on primary plane enable/disable where we didn't have one
before (which wasn't really correct, but we had been getting lucky
because we always calculated as if the primary plane was on).
Together, these two commits cause the watermark calculation to
(properly) see plane->state->fb = NULL when we're in the process of
disabling the primary plane. However the existing watermark code
assumes there's always a primary fb and tries to dereference it to find
out pixel format / bpp information.
The fix is to make ILK-style watermark calculation actually check the
true status of primary & cursor planes and adjust our watermark logic
accordingly.
v2: Update unchecked uses of state->fb for other platforms (pnv, skl,
etc.). Note that this is just a temporary fix. Ultimately the
useful information is going to be computed at check time and stored
right in the state structures so that we don't have to figure this
all out while we're supposed to be programming the watermarks.
(caught by Tvrtko)
v3: Fix a couple copy/paste mistakes in SKL code. (Tvrtko)
v4: Only add FB checks for ILK/SKL codepaths. Older platforms still use
intel_crtc_active() and will shortcircuit out of watermark
calculations before ever trying to dereference the primary plane's
framebuffer.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Michael Leuchtenburg <michael@slashhome.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89388
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_user_framebuffer_destroy() requires the struct_mutex for its
object bookkeeping, so this means that all calls to
drm_framebuffer_unreference must not hold that lock.
Regression from commit ab8d66752a
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Feb 2 15:44:15 2015 +0000
drm/i915: Track old framebuffer instead of object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89166
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Clarify commit message slightly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDR DVFS introduces massive memory latencies which can't be handled by
the PND deadline stuff. Instead the watermarks will need to be
programmed to compensate for the latency and the deadlines will need to
be programmed to tight fixed values. That means DDR DVFS can only be
enabled if the display FIFOs are large enough, and that pretty much
means we have to manually repartition them to suit the needs of the
moment.
That's a lot of change, so in the meantime let's just disable DDR DVFS
to get the display(s) to be stable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a new knob in Punit to select between some memory power savings
modes PM2 and PM5. We can allow the deeper PM5 when maxfifo mode is
enabled, so let's do so in the hopes for moar power savings.
v2: Put the thing into a separate function to avoid churn later
v3: Don't break VLV
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PFI credit programming is required when CD clock (related to data flow from
display pipeline to end display) is greater than CZ clock (related to data
flow from memory to display plane). This programming should be done when all
planes are OFF to avoid intermittent hangs while accessing memory even from
different Gfx units (not just display).
If cdclk/czclk >=1, PFI credits could be set as any number. To get better
performance, larger PFI credit can be assigned to PND. Otherwise if
cdclk/czclk<1, the default PFI credit of 8 should be set.
v2:
- Change log to lower log level instead of DRM_ERROR
- Change function name to valleyview_program_pfi_credits
- Move program PFI credits to modeset_init instead of intel_set_mode
- Change magic numbers to logical constants
[vsyrjala v3:
- only program in response to cdclk update
- program the credits also when cdclk<czclk
- add CHV bits
v4:
- Change CHV cdclk<czclk credits to 12 (Vijay)]
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assuming the PND deadline mechanism works reasonably we should do
memory requests as early as possible so that PND has schedule the
requests more intelligently. Currently we're still calculating
the watermarks as if VLV/CHV are identical to g4x, which isn't
the case.
The current code also seems to calculate insufficient watermarks
and hence we're seeing some underruns, especially on high resolution
displays.
To fix it just rip out the current code and replace is with something
that tries to utilize PND as efficiently as possible.
We now calculate the WM watermark to trigger when the FIFO still has
256us worth of data. 256us is the maximum deadline value supoorted by
PND, so issuing memory requests earlier would mean we probably couldn't
utilize the full FIFO as PND would attempt to return the data at
least in at least 256us. We also clamp the watermark to at least 8
cachelines as that's the magic watermark that enabling trickle feed
would also impose. I'm assuming it matches some burst size.
In theory we could just enable trickle feed and ignore the WM values,
except trickle feed doesn't work with max fifo mode anyway, so we'd
still need to calculate the SR watermarks. It seems cleaner to just
disable trickle feed and calculate all watermarks the same way. Also
trickle feed wouldn't account for the 256us max deadline value, thoguh
that may be a moot point in non-max fifo mode sicne the FIFOs are fairly
small.
On VLV max fifo mode can be used with either primary or sprite planes.
So the code now also checks all the planes (apart from the cursor)
when calculating the SR plane watermark.
We don't have to worry about the WM1 watermarks since we're using the
PND deadline scheme which means the hardware ignores WM1 values.
v2: Use plane->state->fb instead of plane->fb
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are some cases like suspend/resume or dpms off/on sequences
that can flush frontbuffer bits. In these cases features that relies
on frontbuffer tracking can start working and user can stop getting
screen updates on fbcon having impression the system is frozen.
So, let's make sure we also invalidate frontbuffer on fbdev blank.
v2: Daniel was right, backtrace didn't show other path than this blank
one so let's make sure frontbuffer bits gets invalidate here instead of
on random write operations that doesn't garantee we track all frontbuffer
writes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Exchange code comments for one that complains about the
locking, like in set_par.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements latest PHY changes in Gain, prop and int co-efficients
based on the vco freq.
v2: Split the original changes into multiple smaller patches based on
review by Ville
v3: Addressed Ville's review comments. Fixed the error introduced in v2.
Clear the old bits before we modify those bits as part of RMW.
v4: TDC target cnt is 10 bits and not 8 bits (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initialize lock detect threshold and select coarse threshold for the
case where M2 fraction division is disabled.
v2: Split the changes into multiple smaller patches (Ville)
v3: Clear out the old bits before we modify those bits as RMW (Ville)
v4: Reset coarse threshold when M2 fraction is enabled (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2 : Handle M2 frac division for both M2 frac and int cases
v3 : Addressed Ville's review comments. Cleared the old bits for RMW
v4 : Fix feedfwd gain (Ville)
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Existing watermark code calls intel_crtc_active() to determine whether a CRTC
is active for the purpose of watermark calculations (and bails out early if it
determines the CRTC is not active). However intel_crtc_active() only returns
true if crtc->primary->fb is non-NULL, which isn't appropriate in the modern
age of universal planes and atomic modeset since userspace can now disable the
primary plane, but leave the CRTC (and other planes) running.
Note that commit
commit 0fda65680e
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Fri Feb 27 15:12:35 2015 +0000
drm/i915/skl: Update watermarks for Y tiling
adds a test for primary plane enable/disable to trigger a watermark update
(previously we ignored updates to primary planes, which wasn't really correct,
but we got lucky since we always pretended the primary plane was on). Tvrtko's
patch tries to update watermarks when we re-enable the primary plane, but that
watermark computation gets aborted early because intel_crtc_active() returns
false due to the disabled primary plane.
Switch the ILK and SKL watermark code over to use crtc->state->active rather
than calling intel_crtc_active() so that we'll properly compute watermarks when
re-enabling the primary plane.
Note that this commit doesn't touch callsites in the watermark code for
older platforms since there were concerns that doing so would lead to
other types of breakage.
Also note that all of the watermark calculation at the moment takes place after
new crtc/plane states are swapped into the DRM objects. This will change in
the future, so we'll be working with in-flight state objects, but for the time
being, crtc->state is what we want to operate on.
v2: Don't drop primary->fb check from intel_crtc_active(), but rather replace
ILK/SKL callsites with direct tests of crtc->state->active. There is
concern that messing with intel_crtc_active() will lead to other breakage for
old hardware platforms. (Ville)
v3: Use intel_crtc->active for now rather than crtc->state->active since
we don't have CRTC states properly hooked up and initialized yet.
We'll defer the switch to crtc->state->active until the atomic CRTC
state work is farther along. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the switch to atomic plumbing for planes, some of our commit-time
work (e.g., watermarks) is done after the new atomic state is swapped
into the relevant DRM object, but before the DRM core has a chance to
update its legacy state values. Switch intel_crtc_active() to look at
the state objects rather than legacy fields to ensure we operate on the
proper values.
Note that we're continuing to use intel_crtc->active here for the time
being since crtc->state isn't really hooked up yet. Once CRTC states
are wired up properly, we'll want to switch this over to use
crtc->state->active instead.
v2: Switch back to intel_crtc->active for now; when Ander's work on CRTC
states is ready, we can flip this over to use crtc->state->active
instead. (Ville)
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Static analysis was complaining that a path existed where we could use
stat[] uninitialized. Fix this by simplifying the logic to exit early if
PSR isn't supported.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs seem to be full of misinformation wrt. the Punit register
0x36. Some versions still show the old VLV bit layout, some the new
layout, and all of them seem to tell us nonsense about the cdclk
value encoding.
Testing on actual hardware has shown that we simply need to program
the desired CCK divider into the Punit register using the new layout of
the bits. Doing that, the status bit change to indicate the same value,
and the CCK 0x6b register also changes accordingly to indicate that CCK
is now using the new divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Supposedly CHV can sustain a pixel clock of up to 95% of
cdclk, as opposed to the 90% limit that was used old older
platforms. Update the cdclk selection code to allow for this.
This will allow eg. HDMI 4k modes with their 297MHz pixel clock
while still respecting the 320 MHz cdclk limit on CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So try to enumerate eDP unconditionally in those cases.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add wa tag Damien dug out.]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was dumping the DDI translation tables to make sure my patch updating
the HDMI entry was doing the right thing when I noticed that the table
was showing reset values after DPMS.
And indeed, the DDI translation registers are in power well 1 on SKL,
and so we're losing their values when shutting down eDP.
Calling intel_prepare_ddi() on PW1 enabling re-programs the table.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't use this function on gen9, no need for that test here.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe interrupt registers are in the actual pipe power well, so we
need to restore them when re-enable the corresponding power well.
I've also copied what we do on HSW/BDW for VGA, even if the we haven't
enabled unclaimed registers just yet.
v2: Don't run skl_power_well_post_enable() if the power well is already
enabled (Paulo)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just to be more consistent with what we do on HSW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like what we do for HSW/BDW, having those variables makes it a bit
easier to parse the code.
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While we only need to restore pipe B/C interrupt registers on BDW when
enabling the power well, skylake a bit more flexible and we'll also need
to restore the pipe A registers as it has its own power well that can be
toggled.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Collect the currently enabled counts of slice, subslice, and
execution units using the power gate control ack message
registers specific to Cherryview.
Slice/subslice/EU info and hardware status can now be
determined for CHV, so allow the debugfs SSEU status dump
to proceed for CHV devices.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Total EU was already being detected on CHV, so we just add the
additional info parameters. The detection method is changed to
be more robust in the case of subslice fusing - we don't want
to trust the EU fuse bits corresponding to subslices which are
fused-off.
v2: Fixed subslice disable bitmasks and removed unnecessary ?
operation (Ville)
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Poke at the CBR1_VLV register during init_clock_gating to make sure the
PND deadline scheme is used.
The hardware has two modes of operation wrt. watermarks:
1) PND deadline mode:
- memory request deadline is calculated from actual FIFO level * DDL
- WM1 watermark values are unused (AFAIK)
- WM watermark level defines when to start fetching data from memory
(assuming trickle feed is not used)
2) backup mode
- deadline is based on FIFO status, DDL is unused
- FIFO split into three regions with WM and WM1 watermarks, each
part specifying a different FIFO status
We want to use the PND deadline mode, so let's make sure the chicken
bit is in the correct position on init.
Also take the opportunity to refactor the shared code between VLV and
CHV to a shared function.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have similar DSPARB registers as older platforms, just more of
them due to more planes. Add a bit of code to read out the current FIFO
split from the registers. Will be useful later when we improve the WM
calculations.
v2: Add display_mmio_offset to DSPARB
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have drm_planes for the cursor and primary we can move the
pixel_size handling into vlv_compute_drain_latency() and just pass the
appropriate plane to it.
v2: Check plane->state->fb instead of plane->fb
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with Matt's s/plane->fb/plane->state->fb/
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce struct vlv_wm_values to house VLV watermark/drain latency
values. We start by using it when computing the drain latency values.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the DDL precision handling into vlv_compute_drain_latency() so the
callers don't have to duplicate the same code to deal with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current drain lantency computation relies on hardcoded limits to
determine when the to use the low vs. high precision multiplier.
Rewrite the code to use a more straightforward approach.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the silly DRAIN_LATENCY_PRECISION_* defines and just use the raw
number instead.
v2: Move the sprite 32/16 -> 16/8 preision multiplier
change to another patch (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we must yet halve the DDL drain latency from what we're
using currently. This little nugget is not in any spec, but came
down through the grapevine.
This makes the displays a bit more stable. Not quite fully stable but at
least they don't fall over immediately on driver load.
v2: Update high_precision in valleyview_update_sprite_wm() too (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have a single unclaimed register, we will have lots. A WARN for
each one makes the machine unusable and does not aid debugging. Convert
the i915.mmio_debug option to a counter for how many WARNs to fire
before shutting up. Even when i915.mmio_debug was disabled it would
continue to shout an *ERROR* for every interrupt, without any
information at all for debugging.
The massive verbiage was added in
commit 5978118c39
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jul 16 17:49:29 2014 -0300
drm/i915: reorganize the unclaimed register detection code
v2: Automatically enable invalid mmio reporting for the *next* invalid
access if mmio_debug is disabled by default. This should give us clearer
debug information without polluting the logs too much.
v3: Compile fixes, rebase.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Update modparam text per the thread.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/intel_ringbuffer.c:435:1-4: WARNING: end returns can be simpified
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 05a2fb157e ("drm/i915: Consolidate forcewake code")
failed to take into account that we have used to reset both
the gen6 style and the multithreaded style forcewake registers.
This is due to fact that ivb can use either, depending on how the
bios has set up the machine.
Mimic the old semantics before we have determined the correct variety
and reset both before the ecobus probe.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently, this has never worked reliably and is currently disabled. Also, the
gains are not particularly impressive. Thus rather than try to keep unused code
from decaying and having to update it for other driver changes, it was decided
to simply remove it.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable all sprite planes when disabling the CRTC. We had
been using the top-level atomic 'disable' entrypoint to accomplish this,
which was wrong. Not only can this lead to various locking issues, it
also modifies the actual plane state, making it impossible to restore
the plane properly later. For example, a DPMS off followed by a DPMS on
will result in any sprite planes in use not being restored properly.
The proper solution here is to call directly into our 'commit plane'
hook with a copy of the plane's current state that has 'visible' set to
false. Committing this dummy state will turn off the plane, but will
not touch the actual plane->state pointer, allowing us to properly
restore the plane state later.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the requested size is less than what the full range
of pdps can address, we end up setting pdps for only the
requested area.
The logical context however needs all pdp entries to be valid.
Prior to commit 06fda602db ("drm/i915: Create page table allocators")
we have been writing pdp entries with dma address of zero instead
of valid pdps. This is supposedly bad even if those pdps are not
addressed.
As commit 06fda602db ("drm/i915: Create page table allocators")
introduced more dynamic structure for pdps, we ended up oopsing
when we populated the lrc context. Analyzing this oops revealed
the fact that we have not been writing valid pdps with bsw, as
it is doing the ppgtt init with 2GB limit in some cases.
We should do the right thing and setup the non addressable part
pdps/pde/pte to scratch page through the minimal structure by
having just pdp with pde entries pointing to same page with
pte entries pointing to scratch page.
But instead of going through that trouble, setup all the pdps
through individual pd pages and pt entries, even for non
addressable parts. And let the clear range point them to scratch
page. This way we populate the lrc with valid pdps and wait
for dynamic page allocation work to land, and do the heavy lifting
for truncating page table tree according to usage.
The regression of oopsing in init was introduced by
commit 06fda602db ("drm/i915: Create page table allocators")
v2: Clear the range for the unused part also (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89350
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Valtteri Rantala <valtteri.rantala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Making the link_clock half in switch inline with the DPLL_CTRL1_* macros
(Ville)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDp 1.4 supports custom frequencies.
Skylake supports following intermediate frequencies : 3.24 GHz, 2.16 GHz and
4.32 GHz along with usual LBR, HBR and HBR2 frequencies.
Read sink supported frequencies and get common frequencies from sink and
source and use these for link training.
v2: Rebased, removed calculation of min_clock since for edp it is taken as
max_clock (as per comment).
v3: Keeping single array for link rates (Satheesh)
v4: Setting LINK_BW_SET to 0 when setting LINK_RATE_SET (Satheesh)
v5: Some minor nits (Ville)
v6: Keeping separate arrays for source and sink rates (Ville)
v7: Remove redundant setting of DP_LINK_BW_SET to 0 (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Using DP_SUPPORTED_LINK_RATES macro for supported_rates array (Satheesh).
v3: Reading dpcd's supported link rates tables based upon edp version in the
same patch.
v4: Move version check under is_edp (Satheesh)
v5: Using le16 for rates, some naming, and removing nested if block (Ville)
v6: Correctly using DP_MAX_SUPPORTED_RATES and removing DP_SUPPORTED_LINK_RATES
(Ville)
v7: Incorrectly removed DP_SUPPORTED_LINK_RATES in v6, re-adding it
v8: Checking return value of intel_dp_dpcd_read_wake() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the blt/render tracking we currently have and use the frontbuffer
tracking infrastructure.
Don't enable things by default yet.
v2: (Rodrigo) Fix small conflict on rebase and typo at subject.
v3: (Paulo) Rebase on RENDER_CS change.
v4: (Paulo) Rebase.
v5: (Paulo) Simplify: flushes don't have origin (Daniel).
Also rebase due to patch order changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In invalidate and flush functions of eDP DRRS, if deferred downclock
work starts execution at a time window between acquiring the drrs
mutex and cancellation of the deferred work
(intel_edp_drrs_downclock_work), then deferred work will find
drrs mutex locked and wait for the same.
Meanwhile the function that acquired mutex drrs invalidate/flush will
wait for the completion of the deferred work before releasing the mutex.
Thats a deadlock.
To avoid such deadlock scenario, this change cancels the deferred work
before acquiring the mutex at invalidate and flush functions.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding a debugfs entry to determine if DRRS is supported or not
V2: [By Ram]: Following details about the active crtc will be filled
in seq-file of the debugfs
1. Encoder output type
2. DRRS Support on this CRTC
3. DRRS current state
4. Current Vrefresh
Format is as follows:
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_HIGH_RR, Vrefresh: 60
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
CRTC 1: Output: eDP, DRRS Supported: Yes (Seamless), DRRS_State: DRRS_LOW_RR, Vrefresh: 40
CRTC 2: Output: HDMI, DRRS Supported : No, VBT DRRS_type: Seamless
V3: [By Ram]: Readability is improved.
Another error case is covered [Daniel]
V4: [By Ram]: Current status of the Idleness DRRS along with
the Front buffer bits are added to the debugfs. [Rodrigo]
V5: [By Ram]: Rephrased to make it easy to understand.
And format is modified. [Rodrigo]
V6: [By Ram]: Modeset mutex are acquired for each crtc along with
renaming the Idleness detection states [Daniel]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: dump full busy_frontbuffer_bits and remove the dubios
computed logical state of DRRS - debugfs is about what is fact,
developers should reach their own conclusion when debugging issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adds a parameter which can be used with DRM_I915_GETPARAM to query the
GPU revision. The intention is to use this in Mesa to implement the
WaDisableSIMD16On3SrcInstr workaround on Skylake but only for
revision 2.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When logging that full mode switch is necessary, log which connector,
encoder or crtc has caused it, so it is easier to figure out what is
goind on by just looking at the log.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have similar macros for crtcs and encoders, and the pattern happens
often enough to justify the macro.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the path were there is no state to duplicate, the allocated crtc
state wouldn't have the crtc backpointer initialized.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current minimum vco frequency leaves us with a gap in our supported
frequencies at 233-243 MHz. Your typical 2560x1440@60 display wants a
pixel clock of 241.5 MHz, which is just withing that gap. Reduce the
allowed vco min frequency to 4.8GHz to reduce the gap to 233-240 MHz,
and thus allow such displays to work.
4.8 GHz is actually the documented (at least in some docs) limit of the
PLL, and we just picked 4.86 GHz originally because that was the lowest
value produced by the PLL spreadsheet, which obviously didn't consider
2560x1440 displays.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for FBC, and possibly for PSR too.
v2: Don't only flush: invalidate too (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to port FBC to the frontbuffer tracking infrastructure, but
for that we need to know what caused the object invalidation so
we can react accordingly: CPU mmaps need manual, GTT mmaps and
flips don't need handling and ring rendering needs nukes.
v2: - s/ORIGIN_RENDER/ORIGIN_CS/ (Daniel, Rodrigo)
- Fix copy/pasted wrong documentation
- Rebase
v3: - Rebase
v4: - Don't pass the operation to flushes (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 3f678c96ab.
We've been a bit too optimistic with this one here :(
The trouble is that internally we're still using these plane
update/disable hooks. Which was totally ok pre-atomic since the drm
core did all the book-keeping updating and these just mostly updated
hw state. But with atomic there's lots more going on, and it causes
heaps of trouble with the load detect code.
This one specifically cause a deadlock since both the load detect code
and the nested plane atomic helper functions tried to grab the same
locks. It only blows up because of the evil tricks though we play with
the implicit ww acquire context.
Applying this revert unearths the NULL deref on already freed
framebuffer objects reported as a regression in 4.0 by various people.
Fixing this will be fairly invasive, hence revert even for the
4.1-next queue.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This translation entry was updated after electrical validation by the hw
team. The other entries are removed from existence as they aren't
validated and because the sole use of a certain type of level shifter
for SKL products is anticipated.
v2: Remove all the other entries and force the use of the 800mv+2dB
config (Sonika)
Suggested-by: Sonika Jindal <sonika.jindal@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.
Let's make for_each_sprite() take dev_priv as its first argument then.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.
Let's make for_each_plane() take dev_priv as its first argument then.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the two-step reset counter increments which braket the actual
reset code and the subsequent wake-up we're guaranteeing that all the
lockless waiters _will_ be woken up. And since we unconditionally bail
out of waits with -EAGAIN (or -EIO) in that case there is not risk of
lost interrupt enabling bits when the lockless wait code races against
a gpu reset.
Let's remove this FIXME as resolved then.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plane->fb is a legacy pointer that not always be up-to-date (or updated
early enough). Make sure the watermark code uses plane->state->fb so
that we're always doing our calculations based on the correct
framebuffers.
This patch was generated by Coccinelle with the following semantic
patch:
@@
struct drm_plane *P;
@@
- P->fb
+ P->state->fb
v2: Rebase
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor size fields in intel_crtc just duplicate the data from
cursor->state.crtc_{w,h} so we don't need them any more. Worse, their
use in the watermark code actually introduces a subtle bug since they
don't get updated to mirror the state values until the plane commit
stage, which is *after* we've already used them to calculate new
watermark values. This happens because we had to move watermark updates
slightly earlier (outside vblank evasion) in commit
commit 32b7eeec4d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Wed Dec 24 07:59:06 2014 -0800
drm/i915: Refactor work that can sleep out of commit (v7)
Dropping the intel_crtc fields and just using the state values (which
are properly updated by the time watermark updates happen) should solve
the problem.
Aside from the actual removal of the struct fields (which are formatted
in a way that I couldn't figure out how to match in Coccinelle), the
rest of this patch was generated via the following semantic patch:
// Drop assignment
@@
struct intel_crtc *C;
struct drm_plane_state S;
@@
(
- C->cursor_width = S.crtc_w;
|
- C->cursor_height = S.crtc_h;
)
// Replace usage
@@
struct intel_crtc *C;
expression E;
@@
(
- C->cursor_width
+ C->base.cursor->state->crtc_w
|
- C->cursor_height
+ C->base.cursor->state->crtc_h
|
- to_intel_crtc(E)->cursor_width
+ E->cursor->state->crtc_w
|
- to_intel_crtc(E)->cursor_height
+ E->cursor->state->crtc_h
)
v2: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89346
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
However, there are some places in kernel code that directly set
plane->fb and neglect to update plane->state->fb. If we never do a
successful update through the atomic pipeline, the RmFB cleanup code
will look at the plane->state->fb pointer, which has never actually
been set to a legitimate value, and try to clean it up, leading to
BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb and call it everywhere the driver tries to manually set
plane->fb outside of the atomic pipeline. In this function, use
drm_atomic_set_fb_for_plane instead of writing plane->state->fb
directly to keep the reference count right.
This is modified from Matt Roper's patch to drm-intel-nightly with
commit id
commit afd65eb4cc
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Feb 3 13:10:04 2015 -0800
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
However this bug exists in mainline kernel too, so I created this to fix
it in mainline kernel.
A minor change is to use drm_atomic_set_fb_for_plane instead of update
reference count manually.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93711
Signed-off-by: Xi Ruoyao <xry111@outlook.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[Jani: included the patch notes in the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Long ago I found that I was getting sporadic errors when booting SNB,
with the symptom being that the first batch died with IPEHR != *ACTHD,
typically caused by the TLB being invalid. These magically disappeared
if I held the forcewake during the entire ring initialisation sequence.
(It can probably be shortened to a short critical section, but the whole
initialisation is full of register writes and so we would be taking and
releasing forcewake almost continually, and so holding it over the
entire sequence will probably be a net win!)
Note some of the kernels I encounted the issue already had the deferred
forcewake release, so it is still relevant.
I know that there have been a few other reports with similar failure
conditions on SNB, I think such as
References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
v2: Wrap i915_gem_init_hw() with its own security blanket as we take
that path following resume and reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 05a2fb157e ("drm/i915: Consolidate forcewake code")
failed to take into account that we have used to reset both
the gen6 style and the multithreaded style forcewake registers.
This is due to fact that ivb can use either, depending on how the
bios has set up the machine.
Mimic the old semantics before we have determined the correct variety
and reset both before the ecobus probe.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This fixes a regression from
commit 5ed0bdf21a
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Jul 16 21:05:06 2014 +0000
drm: i915: Use nsec based interfaces
that made a negative timeout return immediately rather than the
previously defined behaviour of waiting indefinitely.
Testcase: igt/gem_wait
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89494
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: fixed a checkpatch complaint about whitespace.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The kernel in_irq() function tests for hard-IRQ context only, so if a
system is run with the kernel 'threadirqs' option selected, the test in
intel_check_page_flip() generates lots of warnings, because then it gets
called in soft-IRQ context.
We can instead use in_interrupt() which allows for either type of
interrupt, while still detecting and complaining about misuse of the
page flip code if it is ever called from non-interrupt context.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89321
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
So no need to have code which never gets called in the driver.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit a8c6ecb3be
Merge: 8dd0eb359eccca0
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Mar 9 19:58:30 2015 +1000
Merge tag 'v4.0-rc3' into drm-next
managed to pick the wrong code to resolve the conflict and left us with
a mutex_lock(struct_mutex) without the mutex_unlock(struct_mutex) leading
to a deadlock. Fix the problem by recovering the correct code which doesn't
need the lock.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
two fixes, both cc'd stable.
* tag 'drm-intel-fixes-2015-03-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU9enEAAoJEHm+PkMAQRiG/ewIAJ4MW4tcAhaVj6ndCF3+uL/b
RaVm1apUjsTloe5Fl0TT9J5CO3zdOetmMNToy2sf0W4MJDIyHf21o83l7eniV/6q
al/c3fQ6HVtNjiSUNghTtzVlL+gUD1F60b9BGYi1V5h2Mp8u0NG1alTGLQfCB8sE
ArB+v2aWEdSPn7mZDA0Yuc1In+8bkpht3oy+OLD/8JNkqqLnml9YOyPjM1cuRpBr
NxKCLcPzSHH9/nR3T6XtkxXYV5xD3+CDm9roJhfHukoFmfT/G3C65Zcp2KEed/Cw
QQpu+ox7fpUs10F/Fbfm8AE+tRB4o2sGh97sprXrO5oaFdx6FPIBo4WN8i/Vy68=
=qpY+
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc2' into drm-fixes
Linux 4.0-rc2
Merging this manually as the i915 change is in it,
and intel fixes are on top of this
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- use the atomic helpers for plane_upate/disable hooks (Matt Roper)
- refactor the initial plane config code (Damien)
- ppgtt prep patches for dynamic pagetable alloc (Ben Widawsky, reworked and
rebased by a lot of other people)
- framebuffer modifier support from Tvrtko Ursulin, drm core code from Rob Clark
- piles of workaround patches for skl from Damien and Nick Hoath
- vGPU support for xengt on the client side (Yu Zhang)
- and the usual smaller things all over
* tag 'drm-intel-next-2015-02-14' of git://anongit.freedesktop.org/drm-intel: (88 commits)
drm/i915: Update DRIVER_DATE to 20150214
drm/i915: Remove references to previously removed UMS config option
drm/i915/skl: Use a LRI for WaDisableDgMirrorFixInHalfSliceChicken5
drm/i915/skl: Fix always true comparison in a revision id check
drm/i915/skl: Implement WaEnableLbsSlaRetryTimerDecrement
drm/i915/skl: Implement WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
drm/i915: Add process identifier to requests
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
drm/i915/skl: Implement WaCcsTlbPrefetchDisable:skl
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
drm/i915/skl: Implement WaDisableHDCInvalidation
drm/i915/skl: Implement WaDisableLSQCROPERFforOCL
drm/i915/skl: Implement WaDisablePartialResolveInVc
drm/i915/skl: Introduce a SKL specific init_workarounds()
drm/i915/skl: Document that we implement WaRsClearFWBitsAtReset
drm/i915/skl: Implement WaSetGAPSunitClckGateDisable
drm/i915/skl: Make the init clock gating function skylake specific
drm/i915/skl: Provide a gen9 specific init_render_ring()
drm/i915/skl: Document the WM read latency W/A with its name
drm/i915/skl: Also detect eDRAM on SKL
...
The current implementation is limited by the number of addresses that
fit into an unsigned long. This causes problems on 32-bit Tegra where
unsigned long is 32-bit but drm_mm is used to manage an IOVA space of
4 GiB. Given the 32-bit limitation, the range is limited to 4 GiB - 1
(or 4 GiB - 4 KiB for page granularity).
This commit changes the start and size of the range to be an unsigned
64-bit integer, thus allowing much larger ranges to be supported.
[airlied: fix i915 warnings and coloring callback]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixupo
Bjørn reported that his machine hang during hibernation and eventually
bisected the problem to the following commit:
commit da2bc1b9db
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Oct 23 19:23:26 2014 +0300
drm/i915: add poweroff_late handler
The problem seems to be that after the kernel puts the device into D3
the BIOS still tries to access it, or otherwise assumes that it's in D0.
This is clearly bogus, since ACPI mandates that devices are put into D3
by the OSPM if they are not wake-up sources. In the future we want to
unify more of the driver's runtime and system suspend paths, for example
by skipping all the system suspend/hibernation hooks if the device is
runtime suspended already. Accordingly for all other platforms the goal
is still to properly power down the device during hibernation.
v2:
- Another GEN4 Lenovo laptop had the same issue, while platforms from
other vendors (including mobile and desktop, GEN4 and non-GEN4) seem
to work fine. Based on this apply the workaround on all GEN4 Lenovo
platforms.
- add code comment about failing platforms (Ville)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-February/060633.html
Reported-and-bisected-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we takeover from the BIOS and install our interrupt handler, the
BIOS may have left us a few surprises in the form of spontaneous
interrupts. (This is especially likely on hardware like 965gm where
display fifo underruns are continuous and the GMCH cannot filter that
interrupt souce.) As we enable our IRQ early so that we can use it
during hardware probing, our interrupt handler must be prepared to
handle a few sources prior to being fully configured. As such, we need
to add a simple is-ready check prior to dereferencing our KMS state for
reporting underruns.
Reported-by: Rob Clark <rclark@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1193972
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[Jani: dropped the extra !]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a tricky story of the new atomic state handling and the legacy
code fighting over each another. The bug at hand is an underrun of the
framebuffer reference with subsequent hilarity caused by the load
detect code. Which is peculiar since the the exact same code works
fine as the implementation of the legacy setcrtc ioctl.
Let's look at the ingredients:
- Currently our code is a crazy mix of legacy modeset interfaces to
set the parameters and half-baked atomic state tracking underneath.
While this transition is going we're using the transitional plane
helpers to update the atomic side (drm_plane_helper_disable/update
and friends), i.e. plane->state->fb. Since the state structure owns
the fb those functions take care of that themselves.
The legacy state (specifically crtc->primary->fb) is still managed
by the old code (and mostly by the drm core), with the fb reference
counting done by callers (core drm for the ioctl or the i915 load
detect code). The relevant commit is
commit ea2c67bb4a
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Dec 23 10:41:52 2014 -0800
drm/i915: Move to atomic plane helpers (v9)
- drm_plane_helper_disable has special code to handle multiple calls
in a row - it checks plane->crtc == NULL and bails out. This is to
match the proper atomic implementation which needs the crtc to get
at the implied locking context atomic updates always need. See
commit acf24a395c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 29 15:33:05 2014 +0200
drm/plane-helper: transitional atomic plane helpers
- The universal plane code split out the implicit primary plane from
the CRTC into it's own full-blown drm_plane object. As part of that
the setcrtc ioctl (which updated both the crtc mode and primary
plane) learned to set crtc->primary->crtc on modeset to make sure
the plane->crtc assignments statate up to date in
commit e13161af80
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:38 2014 -0700
drm: Add drm_crtc_init_with_planes() (v2)
Unfortunately we've forgotten to update the load detect code. Which
wasn't a problem since the load detect modeset is temporary and
always undone before we drop the locks.
- Finally there is a organically grown history (i.e. don't ask) around
who sets the legacy plane->fb for the various driver entry points.
Originally updating that was the drivers duty, but for almost all
places we've moved that (plus updating the refcounts) into the core.
Again the exception is the load detect code.
Taking all together the following happens:
- The load detect code doesn't set crtc->primary->crtc. This is only
really an issue on crtcs never before used or when userspace
explicitly disabled the primary plane.
- The plane helper glue code short-circuits because of that and leaves
a non-NULL fb behind in plane->state->fb and plane->fb. The state
fb isn't a real problem (it's properly refcounted on its own), it's
just the canary.
- Load detect code drops the reference for that fb, but doesn't set
plane->fb = NULL. This is ok since it's still living in that old
world where drivers had to clear the pointer but the core/callers
handled the refcounting.
- On the next modeset the drm core notices plane->fb and takes care of
refcounting it properly by doing another unref. This drops the
refcount to zero, leaving state->plane now pointing at freed memory.
- intel_plane_duplicate_state still assume it owns a reference to that
very state->fb and bad things start to happen.
Fix this all by applying the same duct-tape as for the legacy setcrtc
ioctl code and set crtc->primary->crtc properly.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For an object right on the boundary of mappable space, as the fenceable
size is stricly greater than the actual size, its fence region may extend
out of mappable space.
Note that only pnv/g33 has fence_size > obj.size and an unmappable
range in the gtt, and there alignment constraints prevent bad things
from happening.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Clarify why this shouldn't change anything as per the
discussion on intel-gfx.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By this patch all underlying bits have been implemented and this
patch actually enables the feature.
v2: Validate passed in fb modifiers to reject garbage. (Daniel Vetter)
v3: Rearrange validation checks per code review comments. (Daniel Vetter)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display watermarks need different programming for different tiling
modes.
Set the relevant flag so this happens during the plane commit and
add relevant data into a structure made available to the watermark
computation code.
v2: Pass in tiling info to sprite plane updates as well.
v3: Rebased for plane handling changes.
v4: Handle fb == NULL when plane is disabled.
v5: Refactored for addfb2 interface.
v6: Refactored for fb modifier changes.
v7: Updated for atomic commit by only updating watermarks when tiling changes.
v8: BSpec watermark calculation updates.
v9: Restrict scope of y_tile_minimum variable. (Damien Lespiau)
v10: Get fb from plane state otherwise we are working on old state.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v9)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Recent BSpect updates have changed the watermark calculation to avoid
display flickering in some cases.
v2: Fix check against DDB allocation and tidy the code a bit. (Damien Lespiau)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now need the bpp of the fb as Yf tiling has different tile widths
depending on it.
v2: Rebased for the new addfb2 interface. (Tvrtko Ursulin)
v3: Rebased for fb modifier changes. (Tvrtko Ursulin)
v4: Added missing case and 128-bit pixel warning. (Damien Lespiau)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake is able to scannout those tiling formats. We need to allow them
in the ADDFB ioctl and tell the harware about it.
v2: Rebased for addfb2 interface. (Tvrtko Ursulin)
v3: Rebased for fb modifier changes. (Tvrtko Ursulin)
v4: Don't allow Y tiled fbs just yet. (Tvrtko Ursulin)
v5: Check for stride alignment and max pitch. (Tvrtko Ursulin)
v6: Simplify maximum pitch check. (Ville Syrjälä)
v7: Drop the gen9 check since requirements are no different. (Ville Syrjälä)
v8: Gen2 has different X tiling stride. (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v7)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly just checks in i915-private modeset ioctls.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lots of lines to remove!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Fixup makefile.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
