The common lane power down flag of a DPIO PHY has a funky semantic:
after the initial enabling of the PHY (so from a disabled state) this
flag will be clear. It will be set only after the PHY will be used for
the first time (for instance due to enabling the corresponding pipe) and
then become unused (due to disabling the pipe). During the initial PHY
enablement we don't know which of the above phases we are in, so move
the check for the flag where this is known, the HW readout code. This is
where the rest of lane power down status checks are done anyway.
This fixes at least a problem on GLK where after module reloading, the
common lane power down flag of PHY1 is set, but the PHY is actually
powered-on and properly set up. The GRC readout code for other PHYs will
hence think that PHY1 is not powered initially and disable it after the
GRC readout. This will cause the AUX power well related to PHY1 to get
disabled in a stuck state, timing out when we try to enable it later.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Fixes: e93da0a013 ("drm/i915/bxt: Sanitiy check the PHY lane power down status")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102777
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171002135307.26117-1-imre.deak@intel.com
No functional changes. Only change the macro from
"DPLL_CFGCR0_DC0_FRAC_SHIFT to DPLL_CFGCR0_DCO_FRACTION_SHIFT
to be consistent with DPLL_CFGCR0_DCO_FRACTION_MASK
and DPLL_CFGCR0_DCO_FRACTION
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505413899-30876-1-git-send-email-manasi.d.navare@intel.com
On clock recovery this function is called to find out
the max voltage swing level that we could go.
However gen 9 functions use the old buffer translation tables
to figure that out. That table is not valid for CNL
causing an invalid number of entries and an invalid selection
on the max voltage swing level.
v2: Let's use same approach that previous platforms.
v3: Actually use n_entries and avoid duplicated -1.
v4: Avoid cnl_max_level and use current style.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831145356.15932-1-rodrigo.vivi@intel.com
Let's get a proper HDMI DDI entry level for vswing programming
sequences on CNL.
Spec doesn't specify any default for HDMI tables,
so let's pick the last entry as the default for now.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-7-rodrigo.vivi@intel.com
No functional changes. But those functions will be needed
to get max level for HDMI and DP, so let's move those
up closer to other similar functions existent for previous
platforms.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-6-rodrigo.vivi@intel.com
Let's start converging CNL buf translations to same style
used on previous platforms. So first thing is to use the
standard signature so we don't need to propagate the voltage
check into other parts of the code, but only on the parts
that it is really useful.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-5-rodrigo.vivi@intel.com
Sequences for DisplayPort asks us to
" Configure voltage swing and related IO settings.
Refer to DDI Buffer section."
before "Configure and enable DDI_BUF_CTL"
On BXT and CNL this means to execute the ddi vswing sequences.
At this point these sequences calls are getting duplicated for DP
because they are all called from DP link trainning sequences.
However this patch is not yet removing it before a futher discussion
since spec also allows that during link training without disabling
anything:
"
Notes
Changing voltage swing during link training:
Change the swing setting following the DDI Buffer section.
The port does not need to be disabled.
"
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-4-rodrigo.vivi@intel.com
Vswing sequences on BXT and CNL are equivalent
to the ddi buffer registers setting on other platforms.
For some reason it got aligned with skl_ddi_set_iboost what
is semantically incorrect. This forced us to keep skipping
ddi buffer translation tables on the platforms that has
the vswing sequences.
v2: Don't mess with DP signal levels on this patch.
Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-3-rodrigo.vivi@intel.com
Let's decouple bxt, glk and cnl dp signal levels
from other DDIs to avoid confusion.
No functional change. Only a reorg to avoid messing
with currently working DP signal levels when
moving voltage swing sequences around to match spec.
v2: ddi_signal_levels is also called from other ddi
platforms, so don't remove IS_GEN9_BC check from
skl_ddi_set_iboos. (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-2-rodrigo.vivi@intel.com
No functional changes. This only moves the DP level
selection to a separated function that will be later
used to organize better the vswing sequences.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-1-rodrigo.vivi@intel.com
The enable/disable/etc. encoder hooks aren't supposed to alter the
state(s), so pass them as const. Unfortunately C lacks any kind of deep
const thingy, so this can't catch all abuses. But at least it acts as a
hint to the reader telling them not to mess about with the state(s).
v2: Update intel_tv_mode_find() and ironlake_edp_pll_on() as well
v3: Deal with intel_sdvo_connector_state
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-9-ville.syrjala@linux.intel.com
The PSR enable/disable need to know things about the crtc state, so
plumb it through. This will become even more important when we start
to reuse the generic infoframe code for the VSC DIP programming as the
infoframe code wants the crtc state as well.
v2: Fix kernel docs
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-7-ville.syrjala@linux.intel.com
DP ports may want to use the video DIP for SDP transmission, so let's
initialize the vfuncs for DP encoders as well. The only exception is
port A eDP prior to HSW as that one doesn't have a video DIP instance.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-6-ville.syrjala@linux.intel.com
Disabling the video DIP when shutting the port down seems like a good
idea.
Bspec says:
"When disabling both the DIP port and DIP transmission,
first disable the port and then disable DIP."
and
"Restriction : GCP is only supported with HDMI when the bits per color is
not equal to 8. GCP must be enabled prior to enabling TRANS_DDI_FUNC_CTL
for HDMI with bits per color not equal to 8 and disabled after disabling
TRANS_DDI_FUNC_CTL"
So let's do it in the .post_disable() hook.
v2: Remove double "dpms off" caused by rebase fail
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822140914.24413-1-ville.syrjala@linux.intel.com
For 0.85V cnl_get_buf_trans_edp() returns the DP table, instead of EDP.
Use the correct table.
The error was pointed out by this clang warning:
drivers/gpu/drm/i915/intel_ddi.c:392:39: warning: variable
'cnl_ddi_translations_edp_0_85V' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static const struct cnl_ddi_buf_trans cnl_ddi_translations_edp_0_85V[] = {
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170717195854.192139-1-mka@chromium.org
The condition for setting the Loadgen Select bit of
PORT_TX_DW4 register during DDI Vswing Sequence should be
Bit rate <=6 GHz whereas the existing code checks only
Bit Rate < 6GHz. This patch fixes this condition.
While at it also remove the redundant paranthesis.
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500329122-32662-1-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo had noticed that inside cnl_ddi_vswing_program
the case was handling voltage but with no indication
of type where a missing type could also take us to that
path. So my first attempt was to add a message to
let clear who trigger that path.
However DK had a better idea that is to handle the
missed type sooner before it might take to that path.
So this v2 here uses his approach.
v2: Handle missed type sooner.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170710205852.28352-1-rodrigo.vivi@intel.com
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
v2: Mika pointed out that 24 was hardcoded while it
should consider ref clock that can be either 24KHz
or 19.2KHz on CNL.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499374321-31152-1-git-send-email-rodrigo.vivi@intel.com
Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.
v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com
All here is pretty much like Kabylake.
Including CFL-U has to use same ddi translation table
as KBL-U for now.
v2: Include missed IS_COFFEELAKE on edp trans table. (DK)
Handle CFL-U with same translation table as KBL-U. (DK and
confirmed with HW engineers)
v3: Adding missed case for IS_CFL_ULT. (DK).
v4: Duh! Now with the real IS_CFL_ULT instead of KBL one. (DK)
Also use IS_GEN9_BC when possible. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497045770-21302-1-git-send-email-rodrigo.vivi@intel.com
vswing programming sequence step 2 requires the Loadgen_select bit to
be set in PORT_TX_DW4 lane reigsters per table defined by Bit rate and
lane width. Implemented the change that was marked as FIXME in the
driver.
v2: (Rodrigo) checkpatch fixes.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-12-git-send-email-rodrigo.vivi@intel.com
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
These tables are used on voltage wswing sequence initialization
on Cannonlake.
It is a complete new format now in use by the voltage swing team,
not following any other standard in use by any other platform.
Also the registers are different as well. So let's redefine
the translation table for Cannonlake.
The table is huge. So we minimized with the fields that are
different or might be different anytime soon. The common
values will be hardcoded on the voltage swing sequence.
v2: Merge the lower and the upper bits to match the spec table
and make review easier. This was possible with the good
idea for Manasi with a better way to handle it on the bit
macro definition presented on previous patch.
Credits-to: Manasi
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-10-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
Atm disabling either DP or eDP outputs can generate a spurious short
pulse interrupt. The reason is that after disabling the port the source
will stop sending a valid stream data, while the sink expects either a
valid stream or the idle pattern. Since neither of this is sent the sink
assumes (after an arbitrary delay) that the link is lost and requests
for link retraining with a short pulse.
The spurious pulse is a real problem at least for eDP panels with long
power-off / power-cycle delays: as part of disabling the output we
disable the panel power. The subsequent spurious short pulse handling
will have to turn the power back on, which means the driver has to do a
redundant wait for the power-off and power-cycle delays. During system
suspend this leads to an unnecessary delay up to ~1s on systems with
such panels as reported by Rui.
To fix this put the sink to DPMS D3 state before turning off the port.
According to the DP spec in this state the sink should not request
retraining. This is also what we do already on pre-ddi platforms.
As an alternative I also tried configuring the port to send idle pattern
- which is against BSPec - and leave the port in normal mode before
turning off the port. Neither of these resolved the problem.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
All it does is pick the encoder and call intel_get_shared_dpll(). We
can just do this in the caller. One less indirection level during code
reading.
As another plus, now the two callers of intel_get_shared_dpll() are
{ironlake,haswell}_crtc_compute_clock().
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490209125-20046-2-git-send-email-paulo.r.zanoni@intel.com
Because {hsw,skl,bxt}_ddi_pll_select all pretty much do the same thing
in slightly different ways. Replace everything with a simple copy of
the function and inline it inside intle_ddi_pll_select().
v2: s/return pll/return pll != NULL/ (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490209125-20046-1-git-send-email-paulo.r.zanoni@intel.com
In I915 driver, there are many places where variable name for
intel_encoder object is given as 'intel_encoder' whereas it would
make more sense to call it just 'encoder' when possible.
This patch does this cleanup in file intel_ddi.c.
PS: There are few functions where both drm_encoder and intel_encoder
are present. For such functions, this patch does nothing.
Suggested-by: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489067021-4709-1-git-send-email-shashank.sharma@intel.com
The logic to enable a DDI in intel_mst_pre_enable_dp() is essentially
the same as in intel_ddi_pre_enable_dp(). So reuse the latter function
by calling the post_disable hook on the intel_dig_port instead of
duplicating that code.
v2: Don't oops because of a NULL encoder->crtc. (Ville)
v3: Warn for MST + PORT_E too. (Ville)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-8-ander.conselvan.de.oliveira@intel.com
Remove direct usages of intel_crtc->config from the DDI code. Functions
that didn't yet take a pipe_config as an argument were coverted to do
so.
v2: s/pipe_config/const crtc_state/ (Ville)
- take crtc from crtc_state. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-7-ander.conselvan.de.oliveira@intel.com
Pass intel_crtc to functions intel_ddi_enable_transcoder_func(),
intel_ddi_set_pipe_settings() and intel_ddi_set_vc_payload_alloc(),
instead of the generic crtc type. By changing the functions
intel_ddi_get_crtc_encoder() so that it receives an intel_crtc
parameter, there is no need for the drm_crtc in the callers.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-6-ander.conselvan.de.oliveira@intel.com
It is preferred to pass pipe_config to functions instead of accessing
crtc->config directly. Follow suit and pass pipe_config to the fdi link
train functions.
v2: Add const; s/pipe_config/crtc_state/ (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302125857.14665-5-ander.conselvan.de.oliveira@intel.com
According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.
v2: Rebase.
- Take power domain references before sanitizing encoders. (Imre)
- Add comment to get_encoder_power_domains() defition. (Ander)
v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)
v4: Put IO power domain before unmapping DPLL. (Imre)
- Change return type of intel_ddi_get_power_domains() to u64. (Imre)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com
Rather than sprinkling ideas of how big the DDI buf translation tables
are somewhere in intel_dp.c, let's concentrate it all in intel_ddi.c
where the actual tables are defined. To that end we introduce
intel_ddi_dp_voltage_max() which will actually look at the proper
translation table to determine what is the maximum voltage swing level
supported.
v2: Mask out the preemphasis bits from the return value of
intel_ddi_dp_voltage_max()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223174901.26749-1-ville.syrjala@linux.intel.com
Convert the big switch statement in translate_signal_level() into a neat
table. The table also serves as documentation for the translation
tables. We'll also have other uses for this table later on.
v2: Remove superfluous space (David)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223173507.17600-2-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Split the code to select the correct translation table into DP,
eDP and FDI specific helpers. This reduces the clutter in
intel_prepare_dp_ddi_buffers(), and we'll have other uses for some
of these new helper functions later on.
v2: Fix typo in commit message (David)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223173507.17600-1-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
The function intel_ddi_get_link_dpll() was added in f169660ed4
("drm/i915/dp: Add a standalone function to obtain shared dpll for
HSW/BDW/SKL/BXT") to "allow for the implementation of a platform
neutral upfront link training function", but such implementation
never landed.
So remove that function and clean up the exported shared DPLL interface.
Fixes: f169660ed4 ("drm/i915/dp: Add a standalone function to obtain shared dpll for HSW/BDW/SKL/BXT")
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484310032-1863-1-git-send-email-ander.conselvan.de.oliveira@intel.com
