Mark function as static because it is not used outside file
drm/ttm/ttm_bo.c.
This eliminates the following warning in drm/ttm/ttm_bo.c:
drivers/gpu/drm/ttm/ttm_bo.c:960:5: warning: no previous prototype for ‘ttm_bo_move_buffer’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
This was introduced in:
commit 7c4a395ff8
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Oct 9 19:17:56 2013 +0300
drm/i915: Don't re-compute pipe watermarks except for the affected pipe
and I missed fixing it in:
commit fec8cba306
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 27 11:10:26 2013 -0800
drm/i915: use crtc_htotal in watermark calculations to match fastboot v2
It's needed for ILK+ platforms to fastboot without crashing on a divide
by 0 after a DPMS on action.
Note: Ville mentioned in his review that this confusion seems to go
down to the original introduction of this code in
commit 801bcfffbb
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri May 31 10:08:35 2013 -0300
drm/i915: properly set HSW WM_PIPE registers
So it seems to have been missed both in the fastboot patch and in the
3d mode suppport (where only crtc_htotal reflects the real pipe
width).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add note based on Ville's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a client looks up a ttm object, don't look it up through the device hash
table, but rather from the file hash table. That makes sure that the client
has indeed put a reference on the object, or in gem terms, has opened
the object; either using prime or using the global "name".
To avoid a performance loss, make sure the file hash table entries can be
looked up from under an RCU lock, and as a consequence, replace the rwlock
with a spinlock, since we never need to take it in read mode only anymore.
Finally add a ttm object lookup function for the device hash table, that is
intended to be used when we put a ref object on a base object or, in gem terms,
when we open the object.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Needed for some vm operations; most notably unmap_mapping_range() with
even_cows = 0.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
This is illegal for at least two reasons:
1) While it may work on some platforms / iommus, obtaining page pointers from
mapped sg-lists is illegal, since the DMA API allows page pointer information
to be destroyed in the sg mapping process.
2) TTM has no way of determining the linear kernel map caching state of the
underlying pages. PTEs with conflicting caching state pointing to the same
pfn is not allowed.
TTM operations touching pages of imported sg-tables should be redirected through
the proper dma-buf operations.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
VM_PFNMAP is faster than VM_MIXEDMAP due to reduced page administration so
use it for shared maps where we don't have any Copy-On-Write pages. For
private maps, we continue to use VM_MIXEDMAP.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
misc fixes for nouveau, one more msi rearm, regression fix for old bioses
crash and leak fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nouveau/nouveau: fix memory leak in nouveau_crtc_page_flip()
drm/nouveau/bios: fix offset calculation for BMPv1 bioses
drm/nouveau: return offset of allocated notifier
drm/nouveau/bios: make jump conditional
drm/nvce/mc: fix msi rearm on GF114
drm/nvc0/gr: fix mthd data submission
drm/nouveau: populate master subdev pointer only when fully constructed
When fastbooting, we read out the pipe timings early on, and then in a
panel fitted config, disable the fitter later. But we weren't updating
the pipe src h/w, which meant the mouse cursor was clipped to the
pfitted size rather than the native size set later. Fix that up so the
cursor is visible in the new mode.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we won't check the state until the next DPMS transition, which
may never happen.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix a memory leak in the nouveau_crtc_page_flip() error handling path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The only BIOS on record that needs the 14 offset has a bios major
version 2 but BMP version 1.01. Another bunch of BIOSes that need the 18
offset have BMP version 2.01 or 5.01 or higher. So instead of looking at the
bios major version, look at the BMP version. BIOSes with BMP version 0
do not contain a detectable script, so always return 0 for them.
See https://bugs.freedesktop.org/show_bug.cgi?id=68835
Reported-by: Mauro Molinari <mauromol@tiscali.it>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DRM driver for MSM depends on symbols from the MSM
IOMMU driver. Add this dependency to the Kconfig file.
Fixes this comile error:
Kernel: arch/arm/boot/zImage is ready
ERROR: "msm_iommu_get_ctx" [drivers/gpu/drm/msm/msm.ko]
undefined!
make[2]: *** [__modpost] Error 1
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Avoid duplicating the same piece of code several times by separating
the watemark vfunc setup from the init_clock_gating vfunc setup on PCH
platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to intialize the watermark vfuncs for BDW, and hence the
watermarks were never updated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like I forgot to update the ILK/SNB/IVB watermark patches to deal
with BDW. Add the relevant BDW checks to make sure we take the HSW
codepaths on BDW as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're dealing with CPU physical addresses here, which may be different from
bus addresses, so rename gtt_bus_addr to gtt_phys_addr to avoid confusion.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move prototype declarations of functions radeon_get_encoder_enum() and
radeon_link_encoder_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warnings in drm/radeon/radeon_encoders.c:
drivers/gpu/drm/radeon/radeon_encoders.c:86:1: warning: no previous prototype for ‘radeon_get_encoder_enum’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_encoders.c:162:1: warning: no previous prototype for ‘radeon_link_encoder_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of functions radeon_add_atom_connector() and
radeon_add_legacy_connector() to header file drm/radeon/radeon_mode.h
because they are used by more than one file.
This eliminates the following warning in drm/radeon/radeon_connectors.c:
drivers/gpu/drm/radeon/radeon_connectors.c:1588:1: warning: no previous prototype for ‘radeon_add_atom_connector’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_connectors.c:2020:1: warning: no previous prototype for ‘radeon_add_legacy_connector’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fixes warnings with -Wmissing-prototypes
Based on initial patches from Rashika Kheria.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Noticed by Rashika Kheria and cherry-picked from
her larger patch set.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Rashika Kheria <rashika.kheria@gmail.com>
Include header file drm/radeon/ci_dpm.h in drm/radeon/ci_smc.c because
it uses function declared in the header file.
This eliminates the following warnings in drm/radeon/ci_smc.c:
drivers/gpu/drm/radeon/ci_smc.c:46:5: warning: no previous prototype for ‘ci_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:113:6: warning: no previous prototype for ‘ci_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:121:6: warning: no previous prototype for ‘ci_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:129:5: warning: no previous prototype for ‘ci_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:136:6: warning: no previous prototype for ‘ci_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:145:6: warning: no previous prototype for ‘ci_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:154:6: warning: no previous prototype for ‘ci_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:165:14: warning: no previous prototype for ‘ci_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:186:14: warning: no previous prototype for ‘ci_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:204:5: warning: no previous prototype for ‘ci_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:251:5: warning: no previous prototype for ‘ci_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/ci_smc.c:266:5: warning: no previous prototype for ‘ci_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move prototype declaration of function radeon_atom_copy_swap() to header
file drm/radeon/radeon_mode.h because it is used by more than one file.
This eliminates the following warnings in drm/radeon/atombios_dp.c:
drivers/gpu/drm/radeon/atombios_dp.c:53:6: warning: no previous prototype for ‘radeon_atom_copy_swap’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include header file gpu/drm/radeon/sislands_smc.h in drm/radeon/si_smc.c
because it uses function declared in the header file.
Remove prototype declaration of function si_set_smc_sram_address() from
drm/radeon/sislands_smc.h because the function is used only in one file
where it is declared static already.
This eliminates the following warnings in drm/radeon/si_smc.c:
drivers/gpu/drm/radeon/si_smc.c:46:5: warning: no previous prototype for ‘si_copy_bytes_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:112:6: warning: no previous prototype for ‘si_start_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:121:6: warning: no previous prototype for ‘si_reset_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:135:5: warning: no previous prototype for ‘si_program_jump_on_start’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:142:6: warning: no previous prototype for ‘si_stop_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:151:6: warning: no previous prototype for ‘si_start_smc_clock’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:160:6: warning: no previous prototype for ‘si_is_smc_running’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:171:14: warning: no previous prototype for ‘si_send_msg_to_smc’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:192:14: warning: no previous prototype for ‘si_wait_for_smc_inactive’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:210:5: warning: no previous prototype for ‘si_load_smc_ucode’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:269:5: warning: no previous prototype for ‘si_read_smc_sram_dword’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/si_smc.c:284:5: warning: no previous prototype for ‘si_write_smc_sram_dword’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add static keyword to the definition of KMS_INVALID_IOCTL(name) in
radeon_kms.c because the functions passed to it as arguments are not
used anywhere else.
This eliminates the following warnings in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:719:1: warning: no previous prototype for ‘radeon_cp_init_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:720:1: warning: no previous prototype for ‘radeon_cp_start_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:721:1: warning: no previous prototype for ‘radeon_cp_stop_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:722:1: warning: no previous prototype for ‘radeon_cp_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:723:1: warning: no previous prototype for ‘radeon_cp_idle_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:724:1: warning: no previous prototype for ‘radeon_cp_resume_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:725:1: warning: no previous prototype for ‘radeon_engine_reset_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:726:1: warning: no previous prototype for ‘radeon_fullscreen_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:727:1: warning: no previous prototype for ‘radeon_cp_swap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:728:1: warning: no previous rototype for ‘radeon_cp_clear_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:729:1: warning: no previous prototype for ‘radeon_cp_vertex_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:730:1: warning: no previous rototype for ‘radeon_cp_indices_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:731:1: warning: no previous prototype for ‘radeon_cp_texture_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:732:1: warning: no previous prototype for ‘radeon_cp_stipple_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:733:1: warning: no previous prototype for ‘radeon_cp_indirect_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:734:1: warning: no previous prototype for ‘radeon_cp_vertex2_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:735:1: warning: no previous prototype for ‘radeon_cp_cmdbuf_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:736:1: warning: no previous prototype for ‘radeon_cp_getparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:737:1: warning: no previous prototype for ‘radeon_cp_flip_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:738:1: warning: no previous prototype for ‘radeon_mem_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:739:1: warning: no previous prototype for ‘radeon_mem_free_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:740:1: warning: no previous rototype for ‘radeon_mem_init_heap_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:741:1: warning: no previous rototype for ‘radeon_irq_emit_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:742:1: warning: no previous prototype for ‘radeon_irq_wait_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:743:1: warning: no previous rototype for ‘radeon_cp_setparam_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:744:1: warning: no previous prototype for ‘radeon_surface_alloc_kms’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_kms.c:745:1: warning: no previous prototype for ‘radeon_surface_free_kms’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function r600_audio_set_dto() as static in drm/radeon/r600_hdmi.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/r600_hdmi.c:
drivers/gpu/drm/radeon/r600_hdmi.c:253:6: warning: no previous prototype for ‘r600_audio_set_dto’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_gem_set_domain() as static in
drm/radeon/radeon_gem.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_gem.c:
drivers/gpu/drm/radeon/radeon_gem.c:89:5: warning: no previous prototype for ‘radeon_gem_set_domain’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_info_ioctl() as static in drm/radeon/radeon_kms.c
because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_kms.c:
drivers/gpu/drm/radeon/radeon_kms.c:194:5: warning: no previous prototype for ‘radeon_info_ioctl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark functions radeon_doorbell_init() and radeon_doorbell_fini() as
static in drm/radeon/radeon_device.c because they are not used outside
this file.
This eliminates the following warning in drm/radeon/radeon_device.c:
drivers/gpu/drm/radeon/radeon_device.c:252:5: warning: no previous prototype for ‘radeon_doorbell_init’ [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_device.c:281:6: warning: no previous prototype for ‘radeon_doorbell_fini’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark function radeon_bo_clear_va() as static in
drm/radeon/radeon_object.c because it is not used outside this file.
This eliminates the following warning in drm/radeon/radeon_object.c:
drivers/gpu/drm/radeon/radeon_object.c:49:6: warning: no previous prototype for ‘radeon_bo_clear_va’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw i2c engines are disabled by default as the
current implementation is still experimental. Print
a warning when users enable it so that it's obvious
when the option is enabled.
v2: check for non-0 rather than 1
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
We're iterating over the CPU transcoders, so check for the correct
power domain.
This fixes many "unclaimed register" error messages.
This can be reproduced by the IGT test mentioned below, but we still
get a FAIL when we run it.
Testcase: igt/kms_lip/flip-vs-panning-vs-hang
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In very rare cases (such as a memory failure stress test) it is possible
to fill the entire ring without emitting a request. Under this
circumstance, the outstanding request is flushed and waited upon. After
space on the ring is cleared, we return to emitting the new command -
except that we just cleared the seqno allocated for this operation and
trigger the sanity check that a request is only ever emitted with a
valid seqno. The fix is to rearrange the code to make sure the
allocation of the seqno for this operation is after any required flushes
of outstanding operations.
The bug exists since the preallocation was introduced in
commit 9d7730914f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Nov 27 16:22:52 2012 +0000
drm/i915: Preallocate next seqno before touching the ring
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple definitions show up multiple times in modinfo output.
There's already an identical one in i915_drv.c along with other MODULE_*
definitions, so drop the lone one in intel_fbdev.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_HZ and DRM_WAKEUP macros are removed, but they still remained.
So this patch fixes build errors by replacing the macros.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves potential deadlock issue that can be incurred
by changing file->f_op and filp->private_data to exynos specific
mapper ops and gem object temporarily.
To resolve this issue, this patch creates a new anon file dedicated
to exynos specific mmaper, and making it used instead of existing one.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The bug from gen6_ppgtt_insert_entries() was replicated into
gen8_ppgtt_insert_entries(). This applies the fix for the OOPS from the
previous patch to the gen8 routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The iommu and gfx on Ironlake do not like each other and require a
big hammer to prevent hard machine hangs. In
commit 5c0422878f
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Oct 17 15:51:55 2011 -0700
drm/i915: ILK + VT-d workaround
we added the workaround, but never emitted any debug message that it was
active. Doing so should help identify known performance regressions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a hang in VBIOS scripts of the form "condition; jump".
The jump used to always be executed, while now it will only be
executed if the condition is true.
See https://bugs.freedesktop.org/show_bug.cgi?id=72943
Reported-by: Darcy Brás da Silva <dardevelin@cidadecool.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
If the initial data element is 0, it will never be written, even
though the value from the previous method may be there.
Signed-off-by: Kelly Doran <kel.p.doran@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Mark function cdv_intel_fixed_panel_mode() as static in
drm/gma500/cdv_intel_dp.c because it is not used outside this file.
This eliminates the following warning in drm/gma500/cdv_intel_dp.c:
drivers/gpu/drm/gma500/cdv_intel_dp.c:680:6: warning: no previous prototype for ‘cdv_intel_fixed_panel_mode’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
My Acer 8510TZ stops displaying anything when X starts with Linus' current
tree. I bisected it down to commit ee1452d745.
This patch reverts commit ee1452d745.
After the revert, everything works as before.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Reported-by: Dylan Borg <borgdylan@hotmail.com> (for a Acer Extensa 5635Z)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gem_gtt_cpu_tlb seems to indicate that it is needed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72869
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since get_pid_task() grabs a reference on the task_struct, we have to drop the
refcount after reading that task's comm name. Use pid_task() with RCU instead.
Also, avoid directly reading like pid_task()->comm because
pid_task() will return NULL if the task have already exit()ed.
This patch fixes both problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use helper functions to simplify _DSM related code in nouveau driver.
After analyzing the ACPI _DSM related code, I changed nouveau_optimus_dsm()
to expect a buffer and nouveau_dsm() to expect an integer only.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix memory leak in function nouveau_optimus_dsm() and nouveau_dsm().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use helper functions to simplify _DSM related code in i915 driver.
Function intel_dsm() is used to check functions supported by ACPI _DSM
method, but it has strange check for special value 0x80000002. After
digging into nouveau driver, I think the check is copied from nouveau
driver and is useless for i915 driver, so remove it.
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- VGA switcheroo was broken for some users as a result of the ACPI-based
PCI hotplug (ACPIPHP) changes in 3.12, because some previously ignored
hotplug events started to be handled. The fix causes them to be
ignored again.
- There are two more issues related to cpufreq's suspend/resume handling
changes from the 3.12 cycle addressed by Viresh Kumar's fixes.
- intel_pstate triggers a divide error in a timer function if the P-state
information it needs is missing during initialization. This leads to
kernel panics on nested KVM clients and is fixed by failing the
initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work around
them by installing an ACPI wakeup notify handler for all PCI devices
with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init, which
is incorrect and causes a section mismatch to occur during build. Fix
from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about missing
_ADR for devices that legitimately don't have it. Fix from Toshi Kani
makes it only print the warnings where they make sense.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSxrJgAAoJEILEb/54YlRxRPkP/ifzrrVhdzqXIEy44b93JeDx
oSmZW6yTO51GZlDx2bjt6CGJcIUDC4ExYV6S2tB44/DL19CYdIxi7oBaXtUvzGRs
oZ6B1wfvKOIxZ0RQguaGd1uerQU304CGwUXu/jpRZ/UuZZFKq5Uts6O3bilGzCfR
Y+MUH+qECwdBXaFHUISdWFsa3lxj0U0kglszh+DsxwS4gy/pLbCu5fKLgHLuNNQC
hhEEToQ6uF4o8hbkGJvgUPo3V3aUSXObgvJh4ntP09YE1AEJScLB4wKmqL0zN8Qj
pbBf1WC5OpGXv8zGM9ErrY64YaKA36uhJvOi6RtBGLbG+pYM6E6IM9zNf4Ku+T79
JNEulpq27aEx2JghNSgMFYQZEOGTH+q24iXZdZlOIvqWpMymATlqP/gAQQIpg3VC
OIIdocMFRsbgwFXf41uyUqs458fg5xREz5k6geWZeyriM45wFShR+JnMopQWc5OB
a3sbcWUShFBL1T0pqYR4SDLDvH4NdEP2NKO2jlqMXUewLXsVRRt/42etGoe0rI3C
cMWPQq7z0GNN+NboUviqwHdxUKqONWGt+pd/3u8FI/Y1IlXEeXQYGawhSu81uCpT
5gLaKDkwOrCSwOw68Msuod0Cce6TnoTowi6hP2aAEu8mDJwQY+toqA3+CPoO8nty
DdhZjP1afEgsVVyjErX4
=LXh0
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
"These commits, except for one, are regression fixes and the remaining
one fixes a divide error leading to a kernel panic. The majority of
the regressions fixed here were introduced during the 3.12 cycle, one
of them is from this cycle and one is older.
Specifics:
- VGA switcheroo was broken for some users as a result of the
ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
previously ignored hotplug events started to be handled. The fix
causes them to be ignored again.
- There are two more issues related to cpufreq's suspend/resume
handling changes from the 3.12 cycle addressed by Viresh Kumar's
fixes.
- intel_pstate triggers a divide error in a timer function if the
P-state information it needs is missing during initialization.
This leads to kernel panics on nested KVM clients and is fixed by
failing the initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work
around them by installing an ACPI wakeup notify handler for all PCI
devices with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init,
which is incorrect and causes a section mismatch to occur during
build. Fix from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about
missing _ADR for devices that legitimately don't have it. Fix from
Toshi Kani makes it only print the warnings where they make sense"
* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
intel_pstate: Fail initialization if P-state information is missing
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
ACPI / PCI / hotplug: Avoid warning when _ADR not present
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Fill in asic family specific versions rather than
using the generic version. This lets us handle asic
specific differences more easily. In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us. Fixes bogus
rptr readback on BE systems.
v2: remove missed cpu_to_le32(), add comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating. This works properly now
that smc is initialized earlier than the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable coarse grained clockgating on CIK dGPUs. This
works properly now that smc is initialized earlier than
the rlc and cp.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need more control over the ordering of dpm init with
respect to the rest of the asic. Specifically, the SMC
has to be initialized before the rlc and cg/pg. The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.
This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now it's called right after enable, but after
reworking the dpm init order, it will get called later
to accomodate loading the smc early, but enabling
thermal interrupts and block powergating later after
the ring tests are complete.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd, etc. until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure interrupts are enabled
before we enable thermal interrupts.
Also, don't powergate uvd until after
the ring tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to wait to enable cg and pg until after
ring tests. Also make sure interrupts are enabled
before we enable thermal interrupts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain features need to be enabled after ring tests
(e.g., powergating, etc.). Add a function pointer
to split out late enable features.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence. Move
fw init up so that it's available for dpm init.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not very fast, but makes it possible to access even the
normally inaccessible parts of VRAM from userspace.
v2: use MM_INDEX_HI for >2GB mem access, add default_llseek
v3: set inode size in the open callback
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we not necessary export the right information.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't have the NUM_BANKS parameter, so we have to calculate it
from the other parameters. NUM_BANKS is not constant on CIK.
This fixes 2D tiling for the display engine on CIK.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow userspace to correctly program the PA_SC_RASTER_CONFIG
register, so it can be considered a fix.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Only the render backends of the first shader engine were enabled. The others
were erroneously disabled. Enabling the other render backends improves
performance a lot.
Unigine Sanctuary on Bonaire:
Before: 15 fps
After: 90 fps
Judging from the fan noise, the GPU was also underclocked when the other
render backends were disabled, resulting in horrible performance. The fan is
a lot noisy under load now.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise the kernel might reject our decoding requests.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM driver for (virtual) vga cards using the bochs dispi
interface, such as the qemu standard vga (qemu -vga std).
Don't bother supporting anything but 32bpp for now, even
though the virtual hardware is able to do that.
Known issue: mmap(/dev/fb0) doesn't work.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc1 improvements from Ville (pre-gm45).
- vlv forcewake improvements from Deepak S.
- Some corner-cases fixes from Mika for the context hang stat code.
- pc8 improvements and prep work for runtime D3 from Paulo, almost ready for
primetime.
- gen2 dpll fixes from Ville.
- DSI improvements from Shobhit Kumar.
- A few smaller fixes and improvements all over.
[airlied: intel_ddi.c conflict fixed up]
* tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel: (61 commits)
drm/i915/bdw: Implement ff workarounds
drm/i915/bdw: Force all Data Cache Data Port access to be Non-Coherent
drm/i915/bdw: Don't use forcewake needlessly
drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
drm/i915: dont call irq_put when irq test is on
drm/i915: Rework the FBC interval/stall stuff a bit
drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
drm/i915: FBC_CONTROL2 is gen4 only
drm/i915: Gen2 FBC1 CFB pitch wants 32B units
drm/i915: split intel_ddi_pll_mode_set in 2 pieces
drm/i915: Fix timeout with missed interrupts in __wait_seqno
drm/i915: touch VGA MSR after we enable the power well
drm/i915: extract hsw_power_well_post_{enable, disable}
drm/i915: remove i915_disable_vga_mem declaration
drm/i915: Parametrize the dphy and other spec specific parameters
drm/i915: Remove redundant DSI PLL enabling
drm/i915: Reorganize the DSI enable/disable sequence
drm/i915: Try harder to get best m, n, p values with minimal error
drm/i915: Compute dsi_clk from pixel clock
drm/i915: Use FLISDSI interface for band gap reset
...
Conflicts:
drivers/gpu/drm/i915/intel_ddi.c
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lQsh
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
* tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (121 commits)
drm/tegra: fix compile w/ CONFIG_DYNAMIC_DEBUG
drm/tegra: Add PRIME support
drm/tegra: Relocate some output-specific code
drm/tegra: Add Tegra124 DC support
drm/tegra: Fix small leak on error in tegra_fb_alloc()
drm/tegra: Make legacy fbdev support optional
drm/tegra: Sort reverse-dependencies alphabetically
drm/tegra: Fix return value check
drm/tegra: Add DSI support
drm/tegra: Disable outputs for power-saving
drm/tegra: Track HDMI enable state
drm/tegra: Fix HDMI audio frequency typo
drm/tegra: Do not export tegra_bo_ops
drm/tegra: Remove spurious blank line
drm/tegra: Increase compile test coverage
drm/tegra: Allow the driver to be built as a module
gpu: host1x: Add Tegra124 support
gpu: host1x: clk_round_rate() can return a zero upon error
gpu: host1x: Fix build warnings
gpu: host1x: Increase compile test coverage
...
rcar misc changes.
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add support for the r8a7791 DU
drm/rcar-du: Add LVDS_LANES quirk
drm/rcar-du: Split features and quirks
drm/rcar-du: Update plane pitch in .mode_set_base() operation
drm/rcar-du: Don't cast crtc to rcrtc twice in the same function
drm/rcar-du: fix return value check in rcar_du_lvdsenc_get_resources()
Besides the 2 fixes for tricky corner cases in gem from Chris I've
promised already two patche from Paulo to fix pc8 warnings (both ported
from -next, bug report from Dave Jones) and one patch from to fix vga
enable/disable on snb+. That one is a really old bug, but apparently it
can cause machine hangs if you try hard enough with vgacon/efifb handover.
* tag 'drm-intel-fixes-2013-12-18' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
drm/i915: get a PC8 reference when enabling the power well
drm/i915: change CRTC assertion on LCPLL disable
drm/i915: Fix erroneous dereference of batch_obj inside reset_status
drm/i915: Prevent double unref following alloc failure during execbuffer
- fix for a long standing corruption bug on some Trinity/Richland parts.
- Stability fix for cayman dpm
- audio fixes for dce6+
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix asic gfx values for scrapper asics
drm/radeon: check for 0 count in speaker allocation and SAD code
drm/radeon/dpm: disable ss on Cayman
drm/radeon/dce6: set correct number of audio pins
Commit "drm/ttm: Don't move non-existing data" didn't take the
swapped-out corner case into account. This patch corrects that.
Fixes blank screen after attempted suspend / hibernate on vmwgfx.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix build error: qxl uses crc32 functions so it needs to select
CRC32.
Also use angle quotes around a kernel header file name.
drivers/built-in.o: In function `qxl_display_read_client_monitors_config':
(.text+0x19d754): undefined reference to `crc32_le'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With CONFIG_DYNAMIC_DEBUG=y, the following compile error occurs:
drivers/gpu/drm/tegra/mipi-phy.c: In function ‘mipi_dphy_timing_validate’:
drivers/gpu/drm/tegra/mipi-phy.c:69:11: error: ‘EINVAL’ undeclared (first use in this function)
drivers/gpu/drm/tegra/mipi-phy.c:69:11: note: each undeclared identifier is reported only once for each function it appears in
Fix this by directly including the header that defines EINVAL.
Fixes: dec727399a ("drm/tegra: Add DSI support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.
Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reformat the help text to follow the style of the other Kconfig files,
and also fix indentation for the "select" lines.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.
HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 has 192 syncpoints whereas its predecessors had 32 syncpoints.
This required changes to the hardware register layout.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Treat both negative and zero return values from clk_round_rate() as
errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error. All other values will be considered valid
rates. The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When debugfs support isn't enabled, gcc complains about some variables
being unused. To avoid further #ifdefery, move debugfs specific setup
code into static functions and use IS_ENABLED(CONFIG_DEBUG_FS) to have
the compiler, rather than the preprocessor, discard them when unused.
The advantage of doing it this way is that all the code will be
compile-tested whether or not debugfs support is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
An earlier patch added a subset of the required HW specific header files
but didn't actually include the right ones when compiling for host1x02.
Signed-off-by: Thierry Reding <treding@nvidia.com>
But only when we indeed set up a gtt mapping. We need this since the
vma also holds a pages_pin_count, on top of the unconditional
pages_pin_count we grab for all stolen objects (to avoid swap-out).
This should avoid a pages_pin_count underrun when cleaning up
framebuffers objects taken over from the BIOS.
Chris mentioned in his review that this bug even predates the vma
conversion.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/r128/r128_state.c:1014:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:1029:9-16: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:904:10-17: WARNING opportunity for memdup_user
/c/kernel-tests/src/cocci/drivers/gpu/drm/r128/r128_state.c:914:9-16: WARNING opportunity for memdup_user
Use memdup_user rather than duplicating its implementation
This is a little bit restricted to reduce false positives
Generated by: coccinelle/api/memdup_user.cocci
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is just used for a debugfs file, and we can easily reconstruct
this number by just walking the list twice. Which isn't really bad for
a debugfs file anyway.
So let's rip this out.
There's the other issue that the dev->vmalist itself is a bit useless,
since that can be reconstructed with all the memory mapping
information from proc. But remove that is a different topic entirely.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's racy, and it's only used in debugfs. There are simpler ways to
know whether something is going on (like looking at dmesg with full
debugging enabled). And they're all much more useful.
So let's just rip this out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now dev->ioctl_count tries to prevent the device from disappearing if
it's still in use. And if we'd actually need this code it would be
hopelessly racy and broken.
But luckily the vfs already takes care of this. So we can just rip it
out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This has the nice advantage that we'll get rid of a DRM_WAIT_ON user
for free.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Checking directly for the right capability is simpler. Also this rids
us of a few places that use DRM_CURRENTPID.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The real linux interfaces are soooo much easier on the eyes ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't have any userspace interfaces that use HZ as a time unit, so
having our own DRM define is useless.
Remove this remnant from the shared drm core days.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The <linux/agp_backend.h> header provides dummy functions and
fallbacks, so no need for screaming macros.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
David Herrmann dutifully moved this locking along when moving the
agp_init call out of the generic drm_dev_register into the pci
specific load helpers.
But afaict there's no need and the reason for that locking has been
purely a historical accident - we need the lock around the driver dev
node registration to paper over the midlayer init races, and the agp
init simply ended up in there. The real fix for all this is of course
to delay the dev (and sysfs/debugfs) interface registration until
everything is fully set up.
Until then stop the cargo-cult locking from spreading and remove the
locking.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call drm_pci_agp_destroy directly, there's no point in the
indirection. Long term we want to shuffle this into each driver's
unload logic, but that needs cleared-up drm lifetime rules first.
v2: Add a dummy function for !CONFIG_PCI, spotted my David Herrmann.
v3: Fixup for the coding style police.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wrapping a kfree is pointless.
v2: Add a comment to the kerneldoc for drm_agp_init to explain where
the kfree happens as requested by David. Note that for modeset drivers
agp cleanup is fairly complicated anyway: The drm_agp_clear is a noop
and drivers must call drm_agp_release on their own. Which they all
seem to do properly.
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The PCI bus helper is the only user of it. Call it directly before
device-registration to get rid of the callback.
Note that all drm_agp_*() calls are locked with the drm-global-mutex so we
need to explicitly lock it during initialization. It's not really clear
why it's needed, but lets be safe.
v2: Rebase on top of the agp_init interface change.
v3: Remove the rebase-fail where I've accidentally killed the ->irq_by_busid
callback a bit too early.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most place actually want to just check for dev->agp (most do, but a
few don't so this fixes a few potential NULL derefs). The only
exception is the agp init code which should check for the AGP driver
feature flag.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the removal of REQUIRE_AGP we can use a void return value
and shed a bit of complexity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only the two intel drivers need this and they can easily check for
working agp support in their driver ->load callbacks.
This is the only reason why agp initialization could fail, so allows
us to rip out a bit of error handling code in the next patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Remove the unneeded mem == NULL check]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current values seem to be defined in a format that's specific to the
i915, gma500 and radeon drivers. To make this more generally useful, use
the values as defined in the specification.
While at it, prefix the constants with DP_ for improved namespacing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gone with the new gem vma offset manager from David.
We can also ditch the uapi header definition from the enum since
userspace never used this. It ended up in there purely for historical
reasons (for reusing the old drm mmap code essentially), not because
userspace ever needed it.
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's really no need for the drm core to keep a list of all
devices of a given driver - the linux device model keeps perfect
track of this already for us.
The exception is old legacy ums drivers using pci shadow attaching.
So rename the lists to make the use case clearer and rip out everything
else.
v2: Rebase on top of David Herrmann's drm device register changes.
Also drop the bogus dev_set_drvdata for platform drivers that somehow
crept into the original version - drivers really should be in full
control of that field.
v3: Initialize driver->legacy_dev_list outside of the loop, spotted by
David Herrmann.
v4: Rebase on top of the newly created host1x drm_bus for tegra.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This very much looks like a remnant of the old legady ums shadow
attach days. Now with the last users gone we can rip it out since
we won't ever support an ums drm driver again.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drvdata pointer is already assigned to something useful.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again no apparent user of the driver data field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to chase one pointer here.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again omap already sets the driver data pointer to the drm_device.
Also drop the driver unregister call, that should be (and already is)
done in the module unload hook.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
tilcdc already stores the drm_device in the driver data pointer. So
use that.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I didn't find any user of the driver data yet, so store the
drm_device pointer in there.
Cc: Inki Dae <inki.dae@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The magic dance drm_platform_exit does is actually a remnant of the
old legacy shadow attach support for platform devices. Modern modesetting
drm drivers shouldn't do this any more (and usb/pci devices actually don't
do this).
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The clk_prepare_enable() call can fail. Check it's return value. We
can't propagate it all the way to the user as the KMS operations in
which the clock is enabled return a void.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all drivers will need take all the modeset locks for dirtyfb, so
push the locking down to the drivers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no reason to keep a reference to objects in the name idr. Each
handle to an object has a reference to the object and just before we
destroy the last handle we take the object out of the name idr. Thus,
if an object is in the name idr, there's at least one reference to the
object.
Or to put it another way, the name idr reference will never keep the
object alive. It just looks like it, which is confusing.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we want to disable all the screens on a system, because that
will allow the graphics card to be put into low-power states. The
problem is that, for example, while all screens are disabled, if we
get a hotplug interrupt, fbcon will decide to set a mode instead of
keeping everything disabled, which will remove us from our low power
states.
Let's assume that if there's a DRM master, it will be able to do
whatever is appropriate when we get the hotplug.
This problem can be reproduced by the runtime PM test program from
intel-gpu-tools: we disable all the screens so the graphics device can
be put into D3, then something triggers a hotplug interrupt, fbcon
sets a mode and breaks our test suite. The problem can be reproduced
more easily by the "i2c" subtest.
Other approaches considered for the problem:
- Return "false" if "bound == 0" and the caller of
drm_fb_helper_is_bound is a hotplug handler. This would break
the case where the machine boots with no outputs connected, then
the user plugs a monitor.
- Add a new IOCTL to force fbcon to not set modes. This would keep
all the current applications behaving the same, but adding a new
IOCTL is not always the greatest idea.
- Return false only if "dev->primary->master && bound == 0". This
was my first implementation, but Chris suggested we should do
the check irrespective of the "bound" variable.
Thanks to Daniel Vetter for the investigation, ideas and the
implementation of the hotplug alternative.
v2: - Do the check first, irrespective of "bound".
- Cc dri-devel
Cc: dri-devel@lists.freedesktop.org
Credits-to: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise we risk that the 2nd part of the line ends up on a line of
it's own, which means a kernel dmesg line without a log level. This
then upsets the dmesg checker in piglit.
Only really happens in some of the truly nasty igt testcases which
race cache dropping (through debugfs) with other gem operations.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always use "void *" for arbitrary memory buffers, as this allows to drop
casts in assignments.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- some more ppgtt prep patches from Ben
- a few fbc fixes from Ville
- power well rework from Imre
- vlv forcewake improvements from Deepak S, Ville and Jesse
- a few smaller things all over
[airlied: fixup forwcewake conflict]
* tag 'drm-intel-next-2013-11-29' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: Fix port name in vlv_wait_port_ready() timeout warning
drm/i915: Return a drm_mode_status enum in the mode_valid vfuncs
drm/i915: add intel_display_power_enabled_sw() for use in atomic ctx
drm/i915: drop DRM_ERROR in intel_fbdev init
drm/i915/vlv: use parallel context restore when coming out of RC6
drm/i915/vlv: use a lower RC6 timeout on VLV
drm/i915/sdvo: Fix up debug output to not split lines
drm/i915: make sparse happy for the new vlv mmio read function
drm/i915: drop the right force-wake engine in the vlv mmio funcs
drm/i915: Fix GT wake FIFO free entries for VLV
drm/i915: Report all GTFIFODBG errors
drm/i915: Enabling DebugFS for valleyview forcewake counts
drm/i915/vlv: Valleyview support for forcewake Individual power wells.
drm/i915: Add power well arguments to force wake routines.
drm/i915: Do not attempt to re-enable an unconnected primary plane
drm/i915: add a debugfs entry for power domain info
drm/i915: add a default always-on power well
drm/i915: don't do BDW/HSW specific powerdomains init on other platforms
drm/i915: protect HSW power well check with IS_HASWELL in redisable_vga
drm/i915: use IS_HASWELL/BROADWELL instead of HAS_POWER_WELL
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
The GMCH_CTRL register (or MGCC in the spec) is at a different address
on Sandybridge, and the address to which we currently write to is
undefined. These stray writes appear to upset (hard hang) my Ivybridge
machine whilst it is in UEFI mode.
Note that the register is still marked as locked RO on Sandybridge, so
vgaarb is still dysfunctional.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use this hook starting from ILK onwards, so change the prefix
accordingly. Also rename functions/struct names used from
haswell_update_wm that are relevant to ILK already.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a driver for simple panels. Such panels can have a regulator that
provides the supply voltage and a separate GPIO to enable the panel.
Optionally the panels can have a backlight associated with them so it
can be enabled or disabled according to the panel's power management
mode.
Support is added for two panels: An AU Optronics 10.1" WSVGA and a
Chunghwa Picture Tubes 10.1" WXGA panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a very simple framework to register and lookup panels. Panel drivers
can initialize a DRM panel and register it with the framework, allowing
them to be retrieved and used by display drivers. Currently only support
for DPMS and obtaining panel modes is provided. However it should be
sufficient to enable a large number of panels. The framework should also
be easily extensible to support more sophisticated kinds of panels such
as DSI.
The framework hasn't been tied into the DRM core, even though it should
be easily possible to do so if that's what we want. In the current
implementation, display drivers can simple make use of it to retrieve a
panel, obtain its modes and control its DPMS mode.
Note that this is currently only tested on systems that boot from a
device tree. No glue code has been written yet for systems that use
platform data, but it should be easy to add.
Signed-off-by: Thierry Reding <treding@nvidia.com>
MIPI DSI bus allows to model DSI hosts and DSI peripherals using the
Linux driver model. DSI hosts are registered by the DSI host drivers.
During registration DSI peripherals will be created from the children
of the DSI host's device tree node. Support for registration from
board-setup code will be added later when needed.
DSI hosts expose operations which can be used by DSI peripheral drivers
to access associated devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
Spread spectrum seems to cause hangs when dynamic clock
switching is enabled. Disable it for now. This does not
affect performance or the amount of power saved. Tracked
down by Martin Andersson.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69723
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Apparently always enabling the sprite scaler magically made
sprites work on ILK in the past.
I think the real reason for the failure was missing sprite
watermark programming, and enabling the scaler effectively
disabled LP1+ watermarks, which was enough to keep things going.
Or it might be that the hardware more or less ignores watermarks
for scaled sprites since things seem to work even if I leave
sprite watermarks at 0 and disable all other planes except the
sprite.
In any case, we left the scaler always on but then failed to
check whether we might be exceeding the scaler's source size
limits. That caused the sprite to fail when a sufficiently
large unscaled image was being displayed.
Now that we're getting proper watermark programming for ILK, we
can keep the scaler disabled unless we need to do actual scaling.
This reverts commit 8aaa81a166.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the watermark registers aren't double bufferd, clearing the
watermarks immediately after writing the sprite registers can be
hazardous.
Until we have something better, add a wait for vblank between the
two steps to make sure the sprite no longer needs the watermark
levels before we clear them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When color keying is used, the primary may not be invisible even though
the sprite fully covers it. So check for color keying before deciding to
disable the primary plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have a very clear method of disabling LP1+ wartermarks,
and we can actually detect if we actually did disable them, or
if they were already disabled. Use that to clean up the
WaCxSRDisabledForSpriteScaling:ivb handling.
I was hoping to apply the workaround in a way that wouldn't
require a blocking wait, but sadly IVB really does appear to
require LP1+ watermarks to be off for an entire frame before
enabling sprite scaling. Simply disabling LP1+ watermarks
during the previous frame is not enough, no matter how early
in the frame we do it :(
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new HSW watermark code can now handle ILK/SNB/IVB as well, so
switch them over. Kill the old code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK doesn't like if we just write the LP1+ watermarks registers with 0.
We need to just disable the watermarks by clearing the enable bit. Use
that method also when disabling LP1+ watermarks in init_clock_gating.
It looks like disabling the sprite LP1 watermarks can cause underruns
even if we just toggle the WM1S_LP_EN bit. So treat that bit like the
actual watermark numbers and avoid setting it to 0 immediately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linetime watermarks don't exist on ILK/SNB/IVB, so don't compute them
except on HSW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK has a bunch of issues with FBC. First of all, BSpec tells us that
FBC WM should never be enabled. Secondly when FBC is enabled
with FBC WM disabled, LP2+ watermarks must be disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multi-pipe LP1+ watermarks are a HSW+ feature, so let's not do it on
earlier generations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK disabling LP1+ watermarks must be done carefully to avoid
underruns. If we just write 0 to the register in the middle of the scan
cycle we often get an underrun. So instead we have to leave the actual
watermark levels in the register intact, and just toggle the enable bit.
Presumably the hardware takes a while to get out of low power mode, and
so the watermark level need to stay valid until that time.
We also have to be careful with the WM1S_LP_EN bit. It seems the
hardware more or less treats it like the actual watermarks numbers, and
so we must not toggle it too soon. Just leave it alone when disabling
the LP1+ watermarks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK/SNB don't have LP2+ watermarks for sprites. Also the LP1 sprite
watermark register has its own enable bit. Take these differences
into account when programming the LP1+ registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK/SNB only LP0/1 watermarks can be enabled when sprites are
enabled, and on ILK/SNB/IVB sprite scaling is limited to LP0 only.
So we can avoid computing the extra levels we're never going to use.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new function ilk_wm_lp_latency() which will tell us what to write
into the WM_LPx register latency field. HSW is different from erlier
gens in this regard.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB the display data buffer partitioning control lives in the
DISP_ARB_CTL2 register. Add the relevant defines/code for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we don't kick out firmware framebuffers like vesafb and
efifb when CONFIG_DRM_I915_FBDEV=n but CONFIG_FB=y.
There's still the pesky issue with vgacon which we should somehow
replace with the dummy console at least. We have a similar issue at
module un/reload, since vgacon state is terminally botched after
i915.ko has loaded in modeset mode. But this gets us a step further at
least.
v2: Use IS_ENABLED - I always get this wrong for tristates. Spotted by
Jani.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Noticed while reviewing a patch and couldn't resist the OCD.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Aside from the fact that it leaves confusing dumps on error capture, it
is entirely unnecessary, and potentially harmful in cases like BDW,
where the instruction has changed.
In reality (seemingly), this will have no behavioral impact.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few command were out of numerical order and had different spacing. Put
them back in numerical order, with proper spacing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to init the reg offset for DPIO once, but we need to reset
DPIO at resume time and at init time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just add an early init since we may need to access DPIO regs early on.
The init call in modeset_init_hw is also needed for the resume case,
when we need to reset DPIO to keep things happy.
v2: split reset and reg init
v3: split patches (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This bug in EDID was exposed by:
commit eccea7920c
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Mon Mar 26 15:12:54 2012 -0400
drm/radeon/kms: improve bpc handling (v2)
Which resulted in kind of regression in 3.5. This fixes
https://bugs.freedesktop.org/show_bug.cgi?id=70934
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
VMAs covering a bo but that didn't start at the same address space offset as
the bo they were mapping were incorrectly generating SEGFAULT errors in
the fault handler.
Reported-by: Joseph Dolinak <kanilo2@yahoo.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
The whole file is wrapped around in #if defined(CONFIG_DEBUG_FS) anyway,
so skip the file at the build level already.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case of error, the function debugfs_create_file() returns NULL
pointer not ERR_PTR() if debugfs is enabled. The IS_ERR() test in
the return value check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't actually do anything with the information yet, but parse and
log what's in the VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The intent was to only enable it by default for optimus, e.g. see the
runtime_idle callback. The suspend callback may be called directly, e.g.
as a result of nouveau_crtc_set_config.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that all the infrastructure is in place and all the tests from
pm_pc8 pass, we can finally enable the feature.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we'll get a fault when someone tries to access the mmap, then we'll
wake up from D3.
v2: - Rebase
v3: - Use gtt active/inactive
Testcase: igt/pm_pc8/gem-mmap-gtt
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add comment + WARN as discussed with Paulo on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hangcheck function requires the hardware to be working, and if
we're suspending we're going to put the HW in D3 state.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.
This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.
v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
v4: - Rebase on top of -fixes instead of -nightly.
This is commit d62292c8f7 in -next, but
we need it in -fixes to address Dave's report.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reported-by: Dave Jones <davej@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.
The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.
This is a replacement for the previous patch named
"drm/i915: get/put PC8 when we get/put a CRTC"
Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
(cherry picked from commit 798183c547
from -next due to Dave's report.)
Reported-by: Dave Jones <davej@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaVSRefCountFullforceMissDisable and
WaDSRefCountFullforceMissDisable
VS is a carry-over from HSW, and DS is likely not used by anyone yet.
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Line of 106 chars is too long. Really.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I stumbled on to some unimplemented errata. To be honest, I am not
really sure of the impact, just that the docs say to do.
No w/a name for this one.
v2: v1 was a stale thing which should have never seen the light of day.
(Haihao)
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not all registers need forcewake even if they're not shadowed.
Add the missing check to gen8_writeX() to avoid needless forcewake
usage when writing eg. display registers.
v2: Use straight up <0x40000 check instead of NEEDS_FORCE_WAKE()
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS or someone else might have done something bad and there
might be old GT FIFO erros reported in GTFIFODBG. Clear those out
in intel_uncore_early_sanitize() to make sure we don't mistake them
for our problems.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All instances of drm_dev_register are followed by drm_dev_free on
failure. Don't free dev->control/render/primary on failure, as they will
be freed by drm_dev_free since commit 8f6599da8e (drm: delay minor
destruction to drm_dev_free()). Instead unplug them.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Part of a driver stack fix that fixes surface overcommiting on single execbuf calls.
* 'vmwgfx-fixes-3.13' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Add max surface memory param
If test is running, irq_get was not called so we should gain
balance by not doing irq_put
"So the rule is: if you access unlocked values, you use ACCESS_ONCE().
You don't say "but it can't matter". Because you simply don't know."
-- Linus
v2: use local variable so it can't change during test (Chris)
v3: update commit msg and use ACCESS_ONCE (Ville)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't touch DPFC_RECOMP_CTL on FBC2, use RMW to update
the FBC_CONTROL on FBC1 to make it easier for people to
experiment with different numbers. Also fix the interval
mask for FBC1.
v2: Rebased
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This causes a race condition between drm_dev_unregister()
and pci_driver.shutdown at shutdown or driver unload time.
We need to revisit how to properly support kexec within
the drm.
This reverts commit 846ae41ae9.
Otherwise we end up with a rather strange looking result.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom Stellard <thomas.stellard@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I implemented support for this, but forget to hook
up the callback so the driver can actually use it.
On asics with a dedicated DMA engine, we use the DMA
engine for buffer migration so this is just for testing
purposes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit ec39f64bba (drm/radeon/dpm: Convert
to use devm_hwmon_register_with_groups) converted one usage of
dev_get_drvdata, but there were two more.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72457
Signed-off-by: Martin Andersson <g02maran@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All mobile gen2 and gen3 chipsets should have FBC1, and the code
should now handle them all. So just set has_fbc=true for all such
chipsets.
Note that fbc is still disabled by default for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 and gen3 don't have the FBC_CONTROL2 register, so don't
touch it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the compressed frame buffer pitch is specified in 32B units
rather than the 64B units used on gen3+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first piece, intel_ddi_pll_select, finds a PLL and assigns it to
the CRTC, but doesn't write any register. It can also fail in case it
doesn't find a PLL.
The second piece, intel_ddi_pll_enable, uses the information stored by
intel_ddi_pll_select to actually enable the PLL by writing to its
register. This function can't fail. We also have some refcount sanity
checks here.
The idea is that one day we'll remove all the functions that touch
registers from haswell_crtc_mode_set to haswell_crtc_enable, so we'll
call intel_ddi_pll_select at haswell_crtc_mode_set and then call
intel_ddi_pll_enable at haswell_crtc_enable. Since I'm already
touching this code, let's take care of this particular split today.
v2: - Clock on the debug message is in KHz
- Add missing POSTING_READ
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Bikeshed comments.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 094f9a54e3 ("drm/i915: Fix __wait_seqno to use true infinite
timeouts") added support for __wait_seqno to detect missing interrupts and
go around them by polling. As there is also timeout detection in
__wait_seqno, the polling and timeout detection were done with the same
timer.
When there has been missed interrupts and polling is needed, the timer is
set to trigger in (now + 1) jiffies in future, instead of the caller
specified timeout.
Now when io_schedule() returns, we calculate the jiffies left to timeout
using the timer expiration value. As the current jiffies is now bound to be
always equal or greater than the expiration value, the timeout_jiffies will
become zero or negative and we return -ETIME to caller even tho the
timeout was never reached.
Fix this by decoupling timeout calculation from timer expiration.
v2: Commit message with some sense in it (Chris Wilson)
v3: add parenthesis on timeout_expire calculation
v4: don't read jiffies without timeout (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some RS690 boards with 64MB of sideport memory show up as
having 128MB sideport + 256MB of UMA. In this case,
just skip the sideport memory and use UMA. This fixes
rendering corruption and should improve performance.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=35457
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fixes regression introduced by:
commit bf51d5e2cd
Author: Paulo Zanoni <paulo.r.zanoni at intel.com>
Date: Wed Jul 3 17:12:13 2013 -0300
drm/i915: switch disable_power_well default value to 1
The bug I'm seeing can be reproduced with:
- Have vgacon configured/enabled
- Make sure the power well gets disabled, then enabled. You can
check this by seeing the messages print by hsw_set_power_well
- Stop your display manager
- echo 0 > /sys/class/vtconsole/vtcon1/bind
I can easily reproduce this by blacklising snd_hda_intel and booting
with eDP+HDMI.
If you do this and then look at dmesg, you'll see we're printing
infinite "Unclaimed register" messages. This is happening because
we're stuck on an infinite loop inside console_unlock(), which is
calling many functions from vgacon.c. And the code that's triggering
the error messages is from vgacon_set_cursor_size().
After we re-enable the power well, every time we read/write the VGA
address 0x3d5 we get an "unclaimed register" interrupt (ERR_INT) and
print error messages. If we write anything to the VGA MSR register (it
doesn't really matter which value you write to bit 0), any
reads/writes to 0x3d5 _don't_ trigger the "unclaimed register" errors
anymore (even if MSR bit 0 is zero). So what happens with the current
code is that when we unbind i915 and bind vgacon, we call
console_unlock(). Function console_unlock() is responsible for
printing any messages that were supposed to be print when the console
was locked, so it calls the TTY layer, which calls the console layer,
which calls vgacon to print the messages. At this point, vgacon
eventually calls vgacon_set_cursor_size(), which touches 0x3d5, which
triggers unclaimed register interrupts. The problem is that when we
get these interrupts, we print the error messages, so we add more work
to console_unlock(), which will try to print it again, and then call
vgacon again, trigger a new interrupt, which will put more stuff to
the buffer, and then we'll be stuck at console_unlock() forever.
If you patch intel_uncore.c to not print anything when we detect
unclaimed registers, we won't get into the console_unlock() infinite
loop and the driver unbind will work just fine. We will still be
getting interrupts every time vgacon touches those registers, but we
will survive. This is a valid experiment, but IMHO it's not the real
fix: if we don't print any error messages we will still keep getting
the interrupts, and if we disable ERR_INT we won't get the interrupt
anymore, but we will also stop getting all the other error interrupts.
I talked about this problem with the HW engineer and his
recommendation is "So don't do any VGA I/O or memory access while the
power well is disabled, and make to re-program MSR after enabling the
power well and before using VGA I/O or memory accesses.".
Notice that this is just a partial fix to fd.o #67813. This fixes the
case where the power well is already enabled when we unbind, not when
it's disabled when we unbind.
V2: - Rebase (first version was sent in September).
V3: - Complete rewrite of the same fix: smaller implementation,
improved commit message.
Testcase: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67813
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to add more code to the post_enable function.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was supposed to have been killed on the same commit that killed the
function, e1264ebe9f, but I guess the
intel_drv.h reorganization accidentally brought it back.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the rings may be processed and their requests deallocated in a
different order to the natural retirement during a reset,
/* Whilst this request exists, batch_obj will be on the
* active_list, and so will hold the active reference. Only when this
* request is retired will the the batch_obj be moved onto the
* inactive_list and lose its active reference. Hence we do not need
* to explicitly hold another reference here.
*/
is violated, and the batch_obj may be dereferenced after it had been
freed on another ring. This can be simply avoided by processing the
status update prior to deallocating any requests.
Fixes regression (a possible OOPS following a GPU hang) from
commit aa60c664e6
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Wed Jun 12 15:13:20 2013 +0300
drm/i915: find guilty batch buffer on ring resets
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Add the code comment Chris supplied.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whilst looking up the objects required for an execbuffer, an untimely
allocation failure in creating the vma results in the object being
unreferenced from two lists. The ownership during the lookup is meant to
be moved from the list of objects being looked to the vma, and this
double unreference upon error results in a use-after-free.
Fixes regression from
commit 27173f1f95
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Wed Aug 14 11:38:36 2013 +0200
drm/i915: Convert execbuf code to use vmas
Based on the fix by Ben Widawsky.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
[danvet: Bikeshed the crucial comment above the ownership transfer as
discussed on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These four patches fix a few issues discovered since the initial merge,
which have been reviewed by Rob Clark and Thierry Reding.
* 'drm-tda998x-3.12-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
DRM: Armada: prime refcounting bug fix
DRM: Armada: fix printing of phys_addr_t/dma_addr_t
DRM: Armada: destroy framebuffer after helper
DRM: Armada: implement lastclose() for fbhelper
Just a bunch of regression fixes plus a few patches for long-standing
issues in gem corner-cases that we've hunted down in the past weeks. Since
apparently people hit those in the wild (and we also have nice igts for
them) I've opted for -fixes and cc: stable.
There's 1-2 things oustanding on top of this where I'm still waiting on
confirmation from testing, but nothing really scary.
* tag 'drm-intel-fixes-2013-12-11' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: don't update the dri1 breadcrumb with modesetting
drm/i915: Repeat eviction search after idling the GPU
drm/i915: Fix use-after-free in do_switch
drm/i915: fix pm init ordering
drm/i915: Hold mutex across i915_gem_release
drm/i915: Skip clock checks on BDW
drm/i915: Do not clobber config status after a forced restore of hw state
drm/i915: Take modeset locks around intel_modeset_setup_hw_state()
As promised bdw fixes come separate for now. Just a few minior things.
* 'bdw-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915/bdw: PIPE_[BC] I[ME]R moved to powerwell
drm/i915/bdw: Limit GTT to 2GB
drm/i915/bdw: Add comment about gen8 HWS PGA
drm/i915/bdw: Free correct number of ppgtt pages
drm/i915/bdw: Do gen6 style reset for gen8
drm/i915/bdw: GEN8 backlight support
drm/i915/bdw: Add BDW to ULT macro
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.
This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels
v2: Mask away the port_bits before use
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DSI PLL will get configured during crtc_enable using ->pre_pll_enable
and no need to do in ->mode_set
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Basically ULPS handling during enable/disable has been moved to
pre_enable and post_disable phases. PLL and panel power disable
also has been moved to post_disable phase. The ULPS entry/exit
sequneces as suggested by HW team is as follows -
During enable time -
set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY
And during disable time to flush all FIFOs -
set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP
Also during disbale sequnece sub-encoder disable is moved to the end
after port is disabled.
v2: Based on comments from Ville
- Detailed epxlaination in the commit messgae
- Moved parameter changes out into another patch
- Backlight enabling will be a new patch
v3: Updated as per Jani's comments
- Removed the I915_WRITE_BITS as it is not needed
- Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable
- Moved disable_panel_power hook to dsi_post_disable
- Replace hardcoding with AFE_LATCHOUT
v4: Make intel_dsi_device_ready and intel_dsi_clear_device_ready static
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Basically check for both +ive and -ive deviation from target clock and
pick the one with minimal error. If we get a direct match, break from
loop to acheive some optimization.
v2: Use signed variable for target and calculated dsi clock values
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pixel clock based calculation is recommended in the MIPI host controller
documentation
v2: Based on review comments from Jani and Ville
- Use dsi_clk in KHz rather than converting in Hz and back to MHz
- RR formula is retained though not used but return dsi_clk in KHz now
- Moved the m-n-p changes into a separate patch
- Removed the parameter check for intel_dsi->dsi_clock_freq. This will be
bought back in if needed when appropriate panel drivers are done
v3: Removed the unused mnp calculation from static table
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some panels require one time programming if they do not contain their
own eeprom for basic register initialization. The sequence is
Panel Reset --> Send OTP --> Enable Pixel Stream --> Enable the panel
v2: Based on review comments from Jani and Ville
- Updated the commit message with more details
- Move the new parameters out of this patch
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On my 855 machine the BIOS uses the following DPLL settings:
DPLL 0x90016000
FP0 = 0x61207
FP1 = 0x21207
With the 66MHz SSC refclock, that puts the BIOS generated VCO
frequency at ~908 MHz, which is lower than the 930 MHz limit
we have currently. This also results in the pixel clock coming
out significantly higher than the requested 65 MHz when we try
to recompute it.
Reduce the the VCO limit to 908 MHz. Combined with the earlier
SSC reference clock accuracy fix, this results in the pixel clock
coming out as 65.08 MHz which is quite close to the target. For
some reason the BIOS uses 64.881 MHz, which isn't quite as close.
This makes kms_flip wf_vblank-ts-check pass for the first time
on this machine \o/
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the SSC refclock frequency in kHz to get more accuracy. Currently
we're pretending that 66 MHz is ~66000 kHz, when in fact it is actually
~66667 kHz. By storing the less rounded kHz value we get a much better
accuracy for out pixel clock calculations.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
That puts the BIOS generated VCO frequency at 1512 MHz, which is
higher than the 1400 MHz limit we have currently.
Let's bump the VCO limit to 1512 MHz and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bruno Prémont has a 855 machine with a 1400x1050 LVDS screen.
The VBT mode is as follows:
0:"1400x1050" 0 108000 1400 1416 1528 1688 1050 1051 1054 1066 0x8 0xa
The BIOS uses the following DPLL settings:
DPLL = 0x90020000
FP0 = 0x2140e
FP1 = 0x21207
We can't generate that pixel clock currently as we're limiting the N
divider to at least 3, whereas the BIOS uses a value of 2.
Let's reduce the N minimum to 2 and see what happens.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to determine the correct p2 divider for LVDS on gen2,
we need to check the CLKB mode from the LVDS port register to
determine if we're dealing with single or dual channel LVDS.
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every ring seems to have a BB_ADDR registers, so include them all in the
error state.
v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BB_ADDR register is documented to be 32bits at least since SNB.
Prior to that the high 32bits were listed as MBZ, so using a 64bit read
doesn't seem worth anything. Also the simulator doesn't like the 64bit
read. So just switch to using a 32bit read instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we're disabling the VDD override bit and the panel is enabled, we
don't need to wait for anything. If the panel is disabled, then we
need to actually wait for panel_power_cycle_delay, not
panel_power_down_delay, because the power down delay was already
respected when we disabled the panel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't see a reason to touch VDD when we're disabling the panel:
since the panel is enabled, we don't need VDD. This saves a few sleep
calls from the vdd_on and vdd_off functions at every modeset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix the patch mangle wiggle has done ... Spotted by Paulo.
Also drop the runtime_pm_put call which now has to go due to different
patch ordering. Also from Paul.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The update is horribly racy since it doesn't protect at all against
concurrent closing of the master fd. And it can't really since that
requires us to grab a mutex.
Instead of jumping through hoops and offloading this to a worker
thread just block this bit of code for the modesetting driver.
Note that the race is fairly easy to hit since we call the breadcrumb
function for any interrupt. So the vblank interrupt (which usually
keeps going for a bit) is enough. But even if we'd block this and only
update the breadcrumb for user interrupts from the CS we could hit
this race with kms/gem userspace: If a non-master is waiting somewhere
(and hence has interrupts enabled) and the master closes its fd
(probably due to crashing).
v2: Add a code comment to explain why fixing this for real isn't
really worth it. Also improve the commit message a bit.
v3: Fix the spelling in the comment.
Reported-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Cc: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We just don't need this. This saves 250ms from every modeset on my
machine.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code to enable/disable PC8 already takes care of saving and
restoring all the registers we need to save/restore, so do a put()
call when we enable PC8 and a get() call when we disable it.
Ideally, in order to make it easier to add runtime PM support to other
platforms, we should move some things from the PC8 code to the runtime
PM code, but let's do this later, since we can make Haswell work right
now.
V2: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Don't actually enable runtime pm since I didn't merge all
patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to merge PC8 and D3 into a single feature, and when we're
in D3 we won't get any hotplug interrupt anyway, so leaving them
enable doesn't make sense, and it also brings us a problem. The
problem is that we get a hotplug interrupt right when we we wake up
from D3, when we're still waking up everything. If we fully disable
interrupts we won't get this hotplug interrupt, so we won't have
problems.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code was checking if all bits of "val" were enabled and
DE_PCH_EVENT_IVB was disabled. The new code doesn't care about the
state of DE_PCH_EVENT_IVB: it just checks if everything else is 1.
The goal is that future patches may completely disable interrupts, and
the LCPLL-disabling code shouldn't care about the state of
DE_PCH_EVENT_IVB.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: I think the commit message is actually wrong in it's
description of what the old test checked, but the new one seems sane.
So meh.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put it when it's off. Otherwise, when you run pm_pc8 from
intel-gpu-tools, and the delayed function that disables VDD runs,
we'll get some messages saying we're touching registers while the HW
is suspended.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are needed when we cat the debugfs and sysfs files.
V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If I add code to enable runtime PM on my Haswell machine, start a
desktop environment, then enable runtime PM, these functions will
complain that they're trying to read/write registers while the
graphics card is suspended.
v2: - Simplify i915_gem_fault changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the hunk in i915_hangcheck_elapsed, it's the wrong thing
to do.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we are actually setting the device to the D3 state, we should
issue the notification.
The opregion spec says we should send the message before the adapter
is about to be placed in a lower power state, and after the adapter is
placed in a higher power state.
Jani originally wrote a similar patch for PC8, but then we discovered
that we were not really changing the PCI D states when
enabling/disabling PC8, so we had to postpone his patch.
v2: - Improve commit message, explaining the expected state.
v3: - Rebase.
Cc: Jani Nikula <jani.nikula@intel.com>
Credits-to: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the current code, at haswell_modeset_global_resources, first we
decide if we want to enable/disable the power well, then we decide if
we want to enable/disable PC8. On the case where we're enabling PC8
this works fine, but on the case where we disable PC8 due to a non-eDP
monitor being enabled, we first enable the power well and then disable
PC8. Although wrong, this doesn't seem to be causing any problems now,
and we don't even see anything in dmesg. But the patches for runtime
D3 turn this problem into a real bug, so we need to fix it.
This fixes the "modeset-non-lpsp" subtest from the "pm_pc8" test from
intel-gpu-tools.
v2: - Rebase (i915_disable_power_well).
v3: - More reabase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already have some checks and shouldn't be reaching these places on
!HAS_PC8 platforms, but add a WARN, just in case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 011c2282c7 changed the way refcounting on imported dma_bufs
works, and this hadn't been spotted while forward-porting Armada.
Reflect the changes in that commit into the Armada driver.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These can be 64-bit quantities, so fix them up appropriately.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Destroy the framebuffer only after the helper, since the helper may
still be referencing the framebufer at this point.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Call drm_fb_helper_restore_fbdev_mode() upon last close so that in the
event of the X server crashing, we have some kind of mode restored.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CRI clock is related to the display PHY, so the setup belongs
in intel_init_dpio().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the advent of hw context support, we gained some objects that are
pinned for the duration of their request. That is we can make aperture
space available by idling the GPU and in the process performing a
context switch back to the always-pinned default context. As such, we
should not conclude that there is no space in the aperture for the
current object until we have unpinned any such context objects.
Note that we also have the problem of outstanding pageflips preventing
eviction of their framebuffer objects to resolve.
Testcase: igt/gem_ctx_exec/eviction
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72507
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since early sanitize and uncore sanitize are called one after the other,
I think, we can remove second forcewake reset which was are calling
twice in both the functions.
Note that this is merge fallout between
commit ef46e0d247
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Nov 16 16:00:09 2013 +0100
drm/i915: restore the early forcewake cleanup
and
commit 521198a2e7
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Aug 23 16:52:30 2013 +0300
drm/i915: sanitize forcewake registers on reset
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Explain how this came to be.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace uses this to workaround overcommit issues
by flushing the command stream early.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem. However, that is possible if
<linux/acpi_io.h> is included, because that file contains
a direct inclusion of <acpi/acpi.h>.
For this reason, remove the direct <acpi/acpi.h> inclusion from
<linux/acpi_io.h>, move that file from include/linux/ to include/acpi/
and make <linux/acpi.h> include it for CONFIG_ACPI set along with the
other ACPI header files. Accordingly, Remove the inclusions of
<linux/acpi_io.h> from everywhere.
Of course, that causes the contents of the new <acpi/acpi_io.h> file
to be available for CONFIG_ACPI set only, so intel_opregion.o that
depends on it should also depend on CONFIG_ACPI (and it really should
not be compiled for CONFIG_ACPI unset anyway).
References: https://01.org/linuxgraphics/sites/default/files/documentation/acpi_igd_opregion_spec.pdf
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, PC8 is enabled at modeset_global_resources, which is called
after intel_modeset_update_state. Due to this, there's a small race
condition on the case where we start enabling PC8, then do a modeset
while PC8 is still being enabled. The racing condition triggers a WARN
because intel_modeset_update_state will mark the CRTC as enabled, then
the thread that's still enabling PC8 might look at the data structure
and think that PC8 is being enabled while a pipe is enabled. Despite
the WARN, this is not really a bug since we'll wait for the
PC8-enabling thread to finish when we call modeset_global_resources.
The spec says the CRTC cannot be enabled when we disable LCPLL, so we
had a check for crtc->base.enabled. If we change to crtc->active we
will still prevent disabling LCPLL while the CRTC is enabled, and we
will also prevent the WARN above.
This is a replacement for the previous patch named
"drm/i915: get/put PC8 when we get/put a CRTC"
Testcase: igt/pm_pc8/modeset-lpsp-stress-no-wait
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So apparently under ridiculous amounts of memory pressure we can get
into trouble in do_switch when we try to move the old hw context
backing storage object onto the active lists.
With list debugging enabled that usually results in us chasing a
poisoned pointer - which means we've hit upon a vma that has been
removed from all lrus with list_del (and then deallocated, so it's a
real use-after free).
Ian Lister has done some great callchain chasing and noticed that we
can reenter do_switch:
i915_gem_do_execbuffer()
i915_switch_context()
do_switch()
from = ring->last_context;
i915_gem_object_pin()
i915_gem_object_bind_to_gtt()
ret = drm_mm_insert_node_in_range_generic();
// If the above call fails then it will try i915_gem_evict_something()
// If that fails it will call i915_gem_evict_everything() ...
i915_gem_evict_everything()
i915_gpu_idle()
i915_switch_context(DEFAULT_CONTEXT)
Like with everything else where the shrinker or eviction code can
invalidate pointers we need to reload relevant state.
Note that there's no need to recheck whether a context switch is still
required because:
- Doing a switch to the same context is harmless (besides wasting a
bit of energy).
- This can only happen with the default context. But since that one's
pinned we'll never call down into evict_everything under normal
circumstances. Note that there's a little driver bringup fun
involved namely that we could recourse into do_switch for the
initial switch. Atm we're fine since we assign the context pointer
only after the call to do_switch at driver load or resume time. And
in the gpu reset case we skip the entire setup sequence (which might
be a bug on its own, but definitely not this one here).
Cc'ing stable since apparently ChromeOS guys are seeing this in the
wild (and not just on artificial stress tests), see the reference.
Note that in upstream code doesn't calle evict_everything directly
from evict_something, that's an extension in this product branch. But
we can still hit upon this bug (and apparently we do, see the linked
backtraces). I've noticed this while trying to construct a testcase
for this bug and utterly failed to provoke it. It looks like we need
to driver the system squarly into the lowmem wall and provoke the
shrinker to evict the context object by doing the last-ditch
evict_everything call.
Aside: There's currently no means to get a badly-fragmenting hw
context object away from a bad spot in the upstream code. We should
fix this by at least adding some code to evict_something to handle hw
contexts.
References: https://code.google.com/p/chromium/issues/detail?id=248191
Reported-by: Ian Lister <ian.lister@intel.com>
Cc: Ian Lister <ian.lister@intel.com>
Cc: stable@vger.kernel.org
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Bloomfield, Jon <jon.bloomfield@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Ian Lister <ian.lister@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shovel a bit more of the the code into the setup function, and call
it earlier. Otherwise lockdep is unhappy since we cancel the delayed
resume work before it's initialized.
While at it also shovel the pc8 setup code into the same functions.
I wanted to also ditch the header declaration of the hws pc8 functions,
but for unfathomable reasons that stuff is in intel_display.c instead
of intel_pm.c.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71980
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we force the hw to idle as our first step during unload, we can abort
the unload upon failure. Later we can probe whether the hardware remain
active even after we try to shut it down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some additional fixes for 3.13. Regression fixes for audio and hw_i2c,
vram fix for some SI PX cards, race fix in the hwmon code, and a few other
odds and ends.
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/atom: fix bus probes when hw_i2c is set (v2)
drm/radeon: fix null pointer dereference in dce6+ audio code
drm/radeon: fixup bad vram size on SI
drm/radeon: fix VGT_GS_INSTANCE_CNT register
drm/radeon: Fix a typo in Cayman and Evergreen registers
drm/radeon/dpm: simplify state adjust logic for NI
drm/radeon: add radeon_vm_bo_update trace point
drm/radeon: add VMID allocation trace point
drm/radeon/dpm: Convert to use devm_hwmon_register_with_groups
drm/radeon: program DCE2 audio dto just like DCE3
drm/radeon: fix typo in fetching mpll params
Ensure the side-by-side (half) flag is added to any existing flags when
adding modes from 3D_Structure_ALL.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some boards seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Just flushing out my pile of bugfixes, most of them for regressions/cc:
stable. Nothing really serious going on.
For outstanding issues we still have the S4 fun due to the hsw S4
duct-tape pending (seems like I need to switch into angry maintainer mode
on that one). And there's the mode merging revert to make my g33 work
again still pending for drm core. For that one I don't have any more clue
(and it looks like no one else has a good idea either). And apparently the
locking WARN fix in here also needs to be replicated for boot, still
confirming that one though.
* tag 'drm-intel-fixes-2013-12-02' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Pin pages whilst allocating for dma-buf vmap()
drm/i915: MI_PREDICATE_RESULT_2 is HSW only
drm/i915: Make the DERRMR SRM target global GTT
drm/i915: use the correct force_wake function at the PC8 code
drm/i915: Fix pipe CSC post offset calculation
drm/i915: Simplify DP vs. eDP detection
drm/i915: Check VBT for eDP ports on VLV
drm/i915: use crtc_htotal in watermark calculations to match fastboot v2
drm/i915: Pin relocations for the duration of constructing the execbuffer
drm/i915: take mode config lock around crtc disable at suspend
drm/i915: Prefer setting PTE cache age to 3
drm/i915/ddi: set sink to power down mode on dp disable
This assortment of patches fix a few build and sparse warnings and make
sure to always return -EFAULT on copy_from_user() failures. Finally the
upcasting from struct drm_crtc to struct tegra_dc is made safer to
prevent potential segmentation faults.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Du68
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.13-rc3' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v3.13-rc3
This assortment of patches fix a few build and sparse warnings and make
sure to always return -EFAULT on copy_from_user() failures. Finally the
upcasting from struct drm_crtc to struct tegra_dc is made safer to
prevent potential segmentation faults.
* tag 'drm/for-3.13-rc3' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: return -EFAULT if copy_from_user() fails
gpu: host1x: Fix a few sparse warnings
drm/tegra: Force cast to __iomem to make sparse happy
drm/tegra: Make tegra_drm_driver static
drm/tegra: Fix address space mismatches
drm/tegra: Tightly bind RGB output to DC
drm/tegra: Make CRTC upcasting safer
gpu: host1x: Silence a few warnings with LPAE=y
5dc9e1e8 was a bit over-ambitious, and accidentially removed handling
for imported prime buffers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix some pageflip, oopses and some better clock support for some chipsets
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nv50/disp: min/max are reversed in nv50_crtc_gamma_set()
drm/nouveau/sw: fix oops if gpu has its display block disabled
drm/nouveau: unreference fence after syncing
drm/nouveau/kms: send timestamp data for correct head in flip completion events
drm/nouveau/clk: Add support for NVAA/NVAC
drm/nouveau/fifo: Hook up pause and resume for NV50 and NV84+
drm/nv10/plane: some chipsets don't support NV12
drm/nv10/plane: add downscaling restrictions
drm/nv10/plane: fix format computation
drm/nv04-nv30/clk: provide an empty domain list
Some user-space apps expects to find them there.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Also request kernel ttm_buffer objects for buffer objects that obviously
aren't visible to user-space, and save some device address space.
The accounting was broken in a couple of ways:
1) We did not differentiate between user dma buffers and kernel dma buffers.
2) The ttm_bo_acc_size function is broken in that it
a) Doesn't take into account the size of the optional dma address array,
b) Doesn't take into account the fact that drivers typically embed the
ttm_tt structure.
This needs to be fixed in ttm, but meanwhile provide a vmwgfx-specific
function to do the job.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Allocation was duplicating code. Comments were missing.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Failure to do this would make the drm_mode_get_crtc ioctl return
without crtc mode info, indicating that no mode was set.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Inorder to serialise the closing of the file descriptor and its
subsequent release of client requests with i915_gem_free_request(), we
need to hold the struct_mutex in i915_gem_release(). Failing to do so
has the potential to trigger an OOPS, later with a use-after-free.
Testcase: igt/gem_close_race
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70874
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71029
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Doing it early prevents moving and relocating objects in vain
for contexts that won't get any GPU time.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is useful to assert that if the object is bound, then it must have
its pages pinned to prevent the shrinker from reaping its backing store.
This is even more useful with the introduction of real-ppgtt whereupon
we may have the object bound into several vma, with each instance
pinning the backing store. This assertion breaks down during unbind
where we unpinned the backing store before decoupling the vma binding.
This can be fixed with a trivial reording of the unbind sequence, which
reinforces the
pin pages
bind to vma
...
unbind from vma
unpin pages
concept.
v2: Bonus comment
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, FIFO will be shared by both SW and HW. So, we read the
free entries through register and update dev_priv variable
and wait for only 20 entries to be free
From Deepak's follow-up mail explaining why vlv is special:
"On SB, Out of 64 FIFO Entries, 20 Entries will be used by HW and
remaining 44 will be used by the SW,. I think due to this reason, we
have a threshold of 20 Entries."
"On VLV, HW and SW can access all 64 fifo entries, I don't think
having a threshold of 20 Entries is mandatory on VLV. Also, since both
SW and HW can access all 64 Entries. I think on VLV, we need to update
the fifo_count before waiting for the FIFO."
v2: Apply mask when we read the number of free FIFO entries (Ville).
v3: Mask applied after reading the register (Deepak).
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Add further explanation from Deepak to commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only plane A is FBC capable on gen2 (like gen3), but the panel fitter
is hooked up to pipe B, so we want to prefer pipe B + plane A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the code comment Chris requested in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initialize the FBC vfuncs on gen2 and gen3 chipsets. Also make
a clean split for gen7+ vs. gen5+ vfunc initialization.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 and gen3 chipsets FBC is supported only on plane A. Fix (and
simplify) the plane checks in intel_update_fbc() accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilons <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a REG_WRITE_FOOTER macro as a counterpart to the REG_WRITE_HEADER.
The current code has the spin_lock() in the HEADER, but the
spin_unlock() is open coded, which looks rather confusing on the first
glance. A bit of additional symmetry might help.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have clock state readout support for DDI, so skip the pipe
config clock checks on all DDI platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We call intel_modeset_setup_hw_state() along two paths, driver
load/resume and after a lid event notification. During initialisation of
the driver, it is imperative that we reset the config state. This
correctly sets up the initial connector statuses and prepares the
hardware for a thorough probing. However, during a lid event, we only
want to undo the damage caused by the bios by resetting our last known
mode. In this cirumstance, we do not want to clobber our desired state.
In order to try and keep sanity between the config state and our own
tracking, do the drm_mode_config_reset() first along the load/resume
paths before reading out the hw state and apply any definite known
corrections.
v2: "As discussed on irc I don't think we should force the connector
state to anything here: Imo connector->status should reflect what we
believe to be the true output connection state, whereas connector->encoder
reflects whether this connector is wired up to a pipe. And since we no
longer reject modeset on disconnected connectors and never nuked the pipe
if the connector gets disconnected there's no reason for that - such policy
is userspace's job.
This regression has been introduced in
commit 2e9388923e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 11 20:08:24 2012 +0200
drm/i915/crt: explicitly set up HOTPLUG_BITS on resume"
so sayeth Daniel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org (v3.8 and later)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some lower level things get angry if we don't have modeset locks
during intel_modeset_setup_hw_state(). Actually the resume and
lid_notify codepaths alreday hold the locks, but the init codepath
doesn't, so fix that.
Note: This slipped through since we only disable pipes if the
plane/pipe linking doesn't match. Which is only relevant on older
gen3 mobile machines, if the BIOS fails to set up our preferred
linking.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Tested-and-reported-by: Paul Bolle <pebolle@tiscali.nl>
[danvet: Add note now that I could confirm my theory with the log
files Paul Bolle provided.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When inspecting reports that boot/suspend/resume times are unusual it
would be useful to clearly identify the time we must spend waiting for
the hardware to complete its task. In this case we have a notification
before we start waiting for the panel to change state, but none
afterwards - which would be useful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checkpatch tells me
WARNING: __packed is preferred over __attribute__((packed))
so switch over to __packed across the driver before adding new packed
structs.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check that the N and P dividers don't cause a divide by zero.
This shouldn't happen under normal circumstances, but can
happen eg. under simulation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should be taking the minimum here instead of the max. It could lead
to a buffer overflow.
Fixes: 438d99e3b1 ('drm/nvd0/disp: initial crtc object implementation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
a/drm/nv50_display.c b/drm/nv50_display.c
index f8e66c08b11a..4e384a2f99c3 100644
Otherwise none of the format checks pass, since the width was still in
16.16 encoding.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
copy_from_user() returns the number of bytes remaining if it fails, but
we want to return -EFAULT here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the bus.h header, so that various function declarations are
visible in the source file that implements those functions. This keeps
sparse from suggesting that they should be made static.
Make the host1x_bus_type variable static since it isn't used globally.
Finally replace the slightly unsafe dev_set_name(dev, name) by the more
secure dev_set_name(dev, "%s", name).
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fbdev screen memory pointer is annotated __iomem, so cast the kernel
virtual address to that address space to make the warning go away.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the association to a DC was done via the encoder's .crtc
field. That has the disadvantage that when an encoder is detached from
its CRTC, that field is set to NULL, leading to situations where it is
impossible to access the DC registers required by the RGB output.
However, the coupling between DC and RGB output is really fixed on
Tegra. While they can be detached logically in DRM, the RGB output can
rely on the DC's existence.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When upcasting a NULL CRTC object, propagate the NULL pointer instead of
some invalid pointer. This allows subsequent code to check that the cast
object is valid.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This register was incorrect for evergreen and cayman.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
According to documentation, 0x00008A60 should be PA_SU_LINE_STIPPLE_VALUE.
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is based on a similar patch from Alexandre Demers.
While fixing up some warnings with that patch I saw some
additional cleanups that could be applied. This patch
simplifies the logic for patching the power state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alexandre Demers <alexandre.f.demers@gmail.com>
Also rename the function to better reflect what it is doing.
agd5f: fix argument size warning
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simplify the code and fix race condition seen because
attribute files were created after hwmon device registration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Copy-paste typo. Value should be 0-2, not 0-1.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It's a pain for two reasons:
- The vga plane redisablign requires actual legacy vgao i/o to pull
of. The hw engineers really botched this one here :(
- There seem to be some BIOS out there which send out lid events when
unplugging. Together with our broken DP code, which disables the
port when the cable is lost, this results in an immediate modeset
call, which can hang on the wait for outstanding flips.
- Also we don't want to force a modeset on machines where it's not
really needed, see the referenced bug.
We might want to extend this in general to also all machines that
support opregion, since there the BIOS supposedly should manage the
gfx hardware more cooperatively.
v2: Pimp commit message a bit.
Cc: Roland Dreier <roland@kernel.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=65486
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch resolves a dead lock issue that could be incurred when
exynos_drm_crtc_dpms function was called.
The exynos_drm_crtc_dpms function waits for the completion of pended
page flip events. However, preclose callback - this releases all unhandled
page flip events - is called prior to the exynos_drm_crtc_dpms function call
when drm is closed. So at this time, this will make the exynos_drm_crtc_dpms
to wait infiniately for the completion of the page flip events.
This patch releases the unhandled page flip events at postclose instead
of preclose so that exynos_drm_crtc_dpms function can be waked up.
Changelog v2:
- fix a memory leak when drm is closed.
. it has a memory leak when a requeste page flip is handled after
drm_events_release() is called and before drm_fb_release()
is called. At this time, a drm_pending_event will not be freed.
So also this chage releases the drm_pending_event at postclose().
And it calls drm_vblank_put() for pair if there is any unhandled page
flip event.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The r8a7791 DU is a stripped-down version of the r8a7790 DU with two
CRTCs and a single LVDS output.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
LVDS lanes 1 and 3 are switched in ES1 hardware (R8A7790). The problem
has been fixed in newer revisions, add a quirk to make the workaround
selectable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
128-byte pitch alignement is not a hardware feature, it's a hardware
bug. Split it from the features field into a new quirks field. New
quirks will be added to support the R8A7791 SoC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When setting a new frame buffer with the mode set base operation the
pitch value might change. Set the hardware plane pitch register at the
same time as the plane base address in the rcar_du_plane_update_base()
function to make sure the pitch value always matches the frame buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
