Improve the comment of SW workaround for CCM lpm issue using
hardware errata description to avoid confusion.
ERR007265: CCM: When improper low-power sequence is used, the SoC
enters low power mode before the ARM core executes WFI.
Software workaround:
1) Software should trigger IRQ #32 (IOMUX) to be always pending
by setting IOMUX_GPR1_GINT.
2) Software should then unmask IRQ #32 in GPC before setting CCM
Low-Power mode.
3) Software should mask IRQ #32 right after CCM Low-Power mode is
set (set bits 0-1 of CCM_CLPCR).
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For ccm clock gate, both 2b'11 and 2b'01 should be treated
as clock enabled, see below description in CCM, whenver CPU
trys to check clock gate's status, system will be in run mode.
2b'00: clock is off during all modes;
2b'01: clock is on in run mode, but off in wait and stop mode;
2b'10: Not applicable;
2b'11: clock is on during all modes, except stop mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Common clk framework will disable unused clks in late init only if
they are enabled by default and no one is using it, so we need to
add is_enabled callback for clk framework to get clks' status.
PFD clocks are enabled by hardware reset, so we need to add
interface for common clk framework to disable those unused ones for
saving power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PFUZE100 regulator is commonly found on mx6 based designs.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Let MX35 and MX50 device tree support be built by default.
Generated by doing:
- Selected CONFIG_MACH_IMX35_DT and CONFIG_SOC_IMX50 via 'make menuconfig'
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v6_v7_defconfig
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We are missing spba clock in imx6sl's clock tree, thus add it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SPDIF can derive a TX clock for playback from one of its clock sources --
spdif root clock to match its supporting sample rates. So this patch set
the spdif root clock's parent to pll3_pfd3_454m since the pll3_pfd3_454m
can approximately meet its sample rate requirement.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
0-DAY kernel build testing backend reports the following.
scripts/checkpatch.pl 0001-ARM-imx-add-support-code-for-IMX50-based-machines.patch
# many are suggestions rather than must-fix
ERROR: Use of const init definition must use __initconst
#80: arch/arm/mach-imx/mach-imx50.c:26:
+static const char *imx50_dt_board_compat[] __initdata = {
While at it, fix the error globally for IMX platform.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ldb_di0_gate is registerd with the clk index of IMX5_CLK_LDB_DI1_GATE,
thus the DI0 interface will be turned off inadvertently during boot.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch sets the parent of CAN peripheral clock (a.k.a. CPI clock) to the
lp_apm clock, which has a rate of 24 MHz.
In the CAN world a base clock with multiple of 8 MHz is suited best for all CIA
recommented bit rates. Without this patch the CAN peripheral clock on i.MX53
has a rate of 66.666 MHz which produces quite large bit rate errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MFN bit 9 on i.MX27 has a different meaning than in other SOCs. This
is a just sign bit. This patch makes different calculation for i.MX27.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to the i.MX50 Rev. 1 and i.MX53 Rev. 2.1 datasheet the lp_apm_sel is
bit 10 in the CCM_CCSR register not bit 9. On the i.MX51 it's bit 9.
This patch fixes this issue.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add SATA PHY clock which are derived from the USB PHY1 clock. Note that this
patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA
driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to
work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of selecting PINCTRL on individual SoC, let's select it at IMX
sub-architecure level.
While at it, it also adds the missing PINCTRL_IMX50 selection for
SOC_IMX50.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ARM clock is sourcing from pll1_sw, and pll1_sw can be either from
pll1_sys or step, so we should enable arm clock during clock
initialization instead of pll1_sys, otherwise, arm clock's usecount
would be incorrect and PLL1 will never be disabled even it is not
used.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use clock defines in order to make devicetrees more
human readable.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Booting a mx6q wandboard with 2GB of RAM we see the following on boot:
Booting Linux on physical CPU 0x0
Linux version 3.12.0-next-20131112+ (fabio@fabio-Latitude-E6410) (gcc version 43
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Wandboard i.MX6 Quad Board
Truncating RAM at 10000000-8fffffff to -7f7fffff (vmalloc region overlap)
...
Select CONFIG_HIGHMEM to avoid the vmalloc region overlap.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add machine support code for the Freescale IMX50 SoC.
The IMX50 is quite similar to the Freescale IMX53, and contains many of the
same periperhal hardware modules, at the same address offsets as the IMX53.
(Notable exceptions are that the IMX50 contains no CAN bus hardware, less
GPIO, no VPU, it does contain an Electrophoretic display controller though).
This support code uses some of the IMX53 setup code to reduce duplication
of what would be identical init IO setup.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The code for irq priorisation support doesn't have any in-tree users and
the Kconfig description does wrong promises because nowadays irq
handlers are called with irqs disabled, so no high prioritized irq can
interrupt a lower prioritized handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Today, imx53 handles iomux configuration using pinctrl driver, so
mxc_iomux_v3_init() call in imx53_init_early() is there for nothing.
Remove the call from there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Allow the Freescale IMX50 SoC support code to be configured on.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add code to support the specific clock tree of the Freescale IMX50 SoC.
It can use much of the common IMX51/IMX53 clocking code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add appropriate UART address definitions and support defines for using the
UARTs of the Freescale IMX50 SoC as debug ports.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The eukrea mbimxsd25 has a gpio regulator for enabling its
LCD display, it also has a gpio button.
We enable the respective drivers in order to be able to use theses
features with this configuration.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PEX860X has GPIO's which are used for PCI Reset lines on the
Gateworks Ventana boards. The GPIO's need to be set as output
level high so as to allow the PCIe devices to come out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
all events. This was prevalent when FTRACE_SELFTEST was enabled which
enables all events several times, and caused the system bootup to
pause for over a minute.
This was tracked down to an addition of a synchronize_sched() performed
when system call tracepoints are unregistered.
The synchronize_sched() is needed between the unregistering of the
system call tracepoint and a deletion of a tracing instance buffer.
But placing the synchronize_sched() in the unreg of *every* system call
tracepoint is a bit overboard. A single synchronize_sched() before
the deletion of the instance is sufficient.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSofYNAAoJEKQekfcNnQGuTUcIAJOx8745KlkFjN4VX+nCWNfP
xrrpnLBymbGMA9lQ4fXk+kdiuhH8DjRYdKq9fU4T481MFYKkToUIZH6NeaLI5fr1
0nBPPjVyAlJ+yt9JbOAYa1jEYnAr27ORDHEtdQnqb6OJSky3oh9jCQi+toxmh2qX
Sv1tIYeAf3K2V/h5xt6uSl9oiZ6KBtwE3f+xkHWNizaU9i2rq2gxd77fSbPNTIps
wLdsESYziA2UeAm13eh8xXo1uqRbfvx7bPr59cu0+3AqdOoaXFG+JoE/MqmljIO5
HkyCKJVqP8HD+QieuEB+hw4zpSsl6A6iKSlaiHm8NMnRRocfM6qMKMQXQ28KhxA=
=sYm/
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"A regression showed up that there's a large delay when enabling all
events. This was prevalent when FTRACE_SELFTEST was enabled which
enables all events several times, and caused the system bootup to
pause for over a minute.
This was tracked down to an addition of a synchronize_sched()
performed when system call tracepoints are unregistered.
The synchronize_sched() is needed between the unregistering of the
system call tracepoint and a deletion of a tracing instance buffer.
But placing the synchronize_sched() in the unreg of *every* system
call tracepoint is a bit overboard. A single synchronize_sched()
before the deletion of the instance is sufficient"
* tag 'trace-fixes-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Only run synchronize_sched() at instance deletion time
Pull aio fix from Benjamin LaHaise:
"AIO fix from Gu Zheng that fixes a GPF that Dave Jones uncovered with
trinity"
* git://git.kvack.org/~bcrl/aio-next:
aio: clean up aio ring in the fail path
This is a set of nine fixes (and one author update). The libsas one should fix
discovery in eSATA devices, the WRITE_SAME one is the largest, but it should
fix a lot of problems we've been getting with the emulated RAID devices
(they've been effectively lying about support and then firmware has been
choking on the commands). The rest are various crash, hang or warn driver
fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSoeU/AAoJEDeqqVYsXL0McPkH/0PdSofj8emMfravBWM5knWk
YPc+JnEYF+LaOmBYE7X4mEBGq4utbRll5IuFPxuw19X7cWS3A0uOE5cBvzOWKOIw
5xjGx5ik6rd04SRl/8wdERTtXJWUcTQFICjS+2IKogUyBuWgPOr+Ked2aDt2UXCQ
zz1QkpLvE9ogKvVo8uuRynFDu7yCVCQB6QFAEiVxKSe+8IphfORQ3co3tczhWwPY
Tp030xHEQFV6fKAO1ZnrtImih3tj5gp4Sp73x54FyjCYajWj95XkSplhAvGE/mXI
xEGbtpuxHkVuS/+u1ziRuL3cVrgZvXRPyZAj3GSB4lOkrqA8danTStb+oRYbGCc=
=nIqW
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of nine fixes (and one author update).
The libsas one should fix discovery in eSATA devices, the WRITE_SAME
one is the largest, but it should fix a lot of problems we've been
getting with the emulated RAID devices (they've been effectively lying
about support and then firmware has been choking on the commands).
The rest are various crash, hang or warn driver fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bfa: Fix crash when symb name set for offline vport
[SCSI] enclosure: fix WARN_ON in dual path device removing
[SCSI] pm80xx: Tasklets synchronization fix.
[SCSI] pm80xx: Resetting the phy state.
[SCSI] pm80xx: Fix for direct attached device.
[SCSI] pm80xx: Module author addition
[SCSI] hpsa: return 0 from driver probe function on success, not 1
[SCSI] hpsa: do not discard scsi status on aborted commands
[SCSI] Disable WRITE SAME for RAID and virtual host adapter drivers
[SCSI] libsas: fix usage of ata_tf_to_fis
Pull IMA fixes from James Morris:
"Here are two more fixes for IMA"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: properly free ima_template_entry structures
ima: Do not free 'entry' before it is initialized
Clean up the aio ring file in the fail path of aio_setup_ring
and ioctx_alloc. And maybe it can fix the GPF issue reported by
Dave Jones:
https://lkml.org/lkml/2013/11/25/898
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to
avoid garbage sysfs files from being left behind in case of a
suspend error.
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled
from the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=gHBV
-----END PGP SIGNATURE-----
Merge tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to avoid
garbage sysfs files from being left behind in case of a suspend error
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled from
the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PowerCap: Fix mode for energy counter
PNP: fix restoring devices after hibernation
cpuidle: Check for dev before deregistering it.
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-epoll:
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
* pnp:
PNP: fix restoring devices after hibernation
* powercap:
PowerCap: Fix mode for energy counter
* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
Pull arch/tile ftrace bug fix from Chris Metcalf:
"This fixes a build failure with allyesconfig reported by Fengguang Wu
and fixed by Tony Lu"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
ftrace: default to tilegx if ARCH=tile is specified
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. It contains:
- A fix for a use-after-free of a request in blk-mq. From Ming Lei
- A fix for a blk-mq bug that could attempt to dereference a NULL rq
if allocation failed
- Two xen-blkfront small fixes
- Cleanup of submit_bio_wait() type uses in the kernel, unifying
that. From Kent
- A fix for 32-bit blkg_rwstat reading. I apologize for this one
looking mangled in the shortlog, it's entirely my fault for missing
an empty line between the description and body of the text"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: fix use-after-free of request
blk-mq: fix dereference of rq->mq_ctx if allocation fails
block: xen-blkfront: Fix possible NULL ptr dereference
xen-blkfront: Silence pfn maybe-uninitialized warning
block: submit_bio_wait() conversions
Update of blkg_stat and blkg_rwstat may happen in bh context
