For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Cc: stable@vger.kernel.org
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For platforms that use device tree or ACPI as the standard way to look
GPIOs up, allow the platform-defined GPIO mappings to be used as a
fallback. This may be useful for platforms that need extra GPIOs mappings
not defined by the firmware.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Give a short overview of the various GPIO documentation files.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add declaration of 'struct of_phandle_args' to avoid the following
warning:
In file included from arch/arm/mach-tegra/board-paz00.c:21:0:
include/linux/gpio/driver.h:102:17: warning: 'struct of_phandle_args' declared inside parameter list
include/linux/gpio/driver.h:102:17: warning: its scope is only this definition or declaration, which is probably not what you want
Also proactively add other definitions/includes that could be missing
in other contexts.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create single model for HP.
The headset jack module was difference between other chrome book.
It need to manual control Mic jack detect.
Chrome OS loaded driver by models. Remove old assigned fixup table from
ALC269 fixup list entry.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By trial and error, I found this patch could work around an issue
where the headset mic would stop working if you switch between the
internal mic and the headset mic, and the internal mic was muted.
It still takes a second or two before the headset mic actually starts
working, but still better than nothing.
Information update from Kailang:
The verb was ADC digital mute(bit 6 default 1).
Switch internal mic and headset mic will run alc_headset_mode_default.
The coef index 0x11 will set to 0x0041.
Because headset mode was fixed type. It doesn't need to run
alc_determine_headset_type.
So, the value still keep 0x0041. ADC was muted.
BugLink: https://bugs.launchpad.net/bugs/1256840
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
re-format and re-word the device tree binding documentation for MPC8xxx
and compatibles, reference the common document for interrupt controllers
and remove outdated duplicate SoC specific information
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <Pawel.Moll@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <devicetree@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This binding shouldn't exist; Tegra20 has two forms of SPI controller
that are documented separately in nvidia,tegra20-sflash.txt and
nvidia,tegra20-slink.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch fix typo of property name from 'pullup-uV' to 'pullup-uv'.
The ntc_thermistor.c use 'pullup-uv' when parsing dt data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Adding Global Mixed-mode Technology Inc. to the list
of devicetree vendor prefixes.
Signed-off-by: Wei Ni <wni@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
phy-supply is an optional property of the fec driver, so add it to the binding
documentation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The binding and support for omap5-mpu which has a cortex-a15
smp core, gic and integrated L2 cache has been existing for sometime.
So Documenting the missing binding here.
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
I'm afraid I'm rather burned out w.r.t. DT bindings. As has probably
been evident, I don't have and haven't made the time to review many
recently. As such, remove myself from that MAINTAINERS entry.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
I'm tossing my hat into the ring of maintainers/reviewers for device tree
bindings based on history of dealing with DT on embedded PPC and starting
work on ARM SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The new templates management mechanism records information associated
to an event into an array of 'ima_field_data' structures and makes it
available through the 'template_data' field of the 'ima_template_entry'
structure (the element of the measurements list created by IMA).
Since 'ima_field_data' contains dynamically allocated data (which length
varies depending on the data associated to a selected template field),
it is not enough to just free the memory reserved for a
'ima_template_entry' structure if something goes wrong.
This patch creates the new function ima_free_template_entry() which
walks the array of 'ima_field_data' structures, frees the memory
referenced by the 'data' pointer and finally the space reserved for
the 'ima_template_entry' structure. Further, it replaces existing kfree()
that have a pointer to an 'ima_template_entry' structure as argument
with calls to the new function.
Fixes: a71dc65: ima: switch to new template management mechanism
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
7bc5f447ce (ima: define new function ima_alloc_init_template() to
API) moved the initialization of 'entry' in ima_add_boot_aggregate() a
bit more below, after the if (ima_used_chip).
So, 'entry' is not initialized while being inside this if-block. So, we
should not attempt to free it.
Found by Coverity (CID: 1131971)
Fixes: 7bc5f447ce (ima: define new function ima_alloc_init_template() to API)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Pull LED subsystem bugfix from Bryan Wu.
* 'leds-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: pwm: Fix for deferred probe in DT booted mode
We need to make sure that the error code from devm_of_pwm_get() is the one
the module returns in case of failure.
Restructure the code to make this possible for DT booted case.
With this patch the driver can ask for deferred probing when the board is
booted with DT.
Fixes for example omap4-sdp board's keyboard backlight led.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In commit 7314e613d5 ("Fix a few incorrectly checked
[io_]remap_pfn_range() calls") the uio driver started more properly
checking the passed-in user mapping arguments against the size of the
actual uio driver data.
That in turn exposed that some driver authors apparently didn't realize
that mmap can only work on a page granularity, and had tried to use it
with smaller mappings, with the new size check catching that out.
So since it's not just the user mmap() arguments that can be confused,
make the uio mmap code also verify that the uio driver has the memory
allocated at page boundaries in order for mmap to work. If the device
memory isn't properly aligned, we return
[ENODEV]
The fildes argument refers to a file whose type is not supported by mmap().
as per the open group documentation on mmap.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bug report from: wenxiong@linux.vnet.ibm.com
The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.
enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.
For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.
Tested-by: wenxiong@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When multiple vectors are used, the vector variable is over written,
resulting in unhandled operation for those vectors.
This fix prevents the problem by maitaining HBA instance and
vector values for each irq.
[jejb: checkpatch fixes]
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of direct attached SATA device delay is not enough.
It will give crash for set device state command response and
wait_for_completion is the best solution for this.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
Pull scheduler fixes from Ingo Molnar:
"Various smaller fixlets, all over the place"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Fix generation of device-drivers
sched: Expose preempt_schedule_irq()
sched: Fix a trivial typo in comments
sched: Remove unused variable in 'struct sched_domain'
sched: Avoid NULL dereference on sd_busy
sched: Check sched_domain before computing group power
MAINTAINERS: Update file patterns in the lockdep and scheduler entries
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSnJuAAAoJEFjIrFwIi8fJj7sIAJQgSEMWJcEOBJ3lujfbhhKr
9GYfyNILfBjaOcH3LkA354U0JB3y4vON/xz6ONzMO4X7Jj6oUzACeEluq2iexlji
VDxqtnDJGS/82TcIN5xOVKRZbIqZ0xdRjK2f4h7AU9lIoIk+SJEJIycG1RGqqrmr
0nv39lUMjQhXNDhUjyt7e6JQj5GHrP0hzp5ngEQGcquPKbHXUInlwkB/kCH3zwju
2kEYQyKSWFoZCVtIBDeHplcZw9r/zWyOHBxjWOVoI/KZk8k+6d2breC3hv0lrhvU
qkJwzJcKZGlFdiCVHLbo3sTHf0NvvfF+qBCv7JbsymYaQc5SkrATmQ/DAUOssg0=
=emSu
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix for
an embarrassing thinko in the new devm master registration code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=DNnX
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix
for an embarrassing thinko in the new devm master registration code"
* tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Restore private register bits.
spi/qspi: Fix qspi remove path.
spi/qspi: cleanup pm_runtime error check.
spi/qspi: set correct platform drvdata in ti_qspi_probe()
spi/pxa2xx: add new ACPI IDs
spi: core: invert success test in devm_spi_register_master
spi: spi-mxs: fix reference leak to master in mxs_spi_remove()
spi: bcm63xx: fix reference leak to master in bcm63xx_spi_remove()
spi: txx9: fix reference leak to master in txx9spi_remove()
spi: mpc512x: fix reference leak to master in mpc512x_psc_spi_do_remove()
spi: rspi: use platform drvdata correctly in rspi_remove()
spi: bcm2835: fix reference leak to master in bcm2835_spi_remove()
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
The pipe code was trying (and failing) to be very careful about freeing
the pipe info only after the last access, with a pattern like:
spin_lock(&inode->i_lock);
if (!--pipe->files) {
inode->i_pipe = NULL;
kill = 1;
}
spin_unlock(&inode->i_lock);
__pipe_unlock(pipe);
if (kill)
free_pipe_info(pipe);
where the final freeing is done last.
HOWEVER. The above is actually broken, because while the freeing is
done at the end, if we have two racing processes releasing the pipe
inode info, the one that *doesn't* free it will decrement the ->files
count, and unlock the inode i_lock, but then still use the
"pipe_inode_info" afterwards when it does the "__pipe_unlock(pipe)".
This is *very* hard to trigger in practice, since the race window is
very small, and adding debug options seems to just hide it by slowing
things down.
Simon originally reported this way back in July as an Oops in
kmem_cache_allocate due to a single bit corruption (due to the final
"spin_unlock(pipe->mutex.wait_lock)" incrementing a field in a different
allocation that had re-used the free'd pipe-info), it's taken this long
to figure out.
Since the 'pipe->files' accesses aren't even protected by the pipe lock
(we very much use the inode lock for that), the simple solution is to
just drop the pipe lock early. And since there were two users of this
pattern, create a helper function for it.
Introduced commit ba5bb14733 ("pipe: take allocation and freeing of
pipe_inode_info out of ->i_mutex").
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Ian Applegate <ia@cloudflare.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # v3.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that AD1986A cannot manage the dynamic pin on/off for
auto-muting, but rather gets confused. Since each output has own amp,
let's use it instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ad_vmaster_eapd_hook() needs to handle the inverted EAPD case
properly, too. Otherwise the output gets broken on Lenovo N100 with
AD1986A codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS Z35HL laptop also needs the very same fix as the previous one
that was applied to ASUS W7J.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66231
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The static checker found a possible array overflow in atmel/abdac.c:
static checker warning: "sound/atmel/abdac.c:373 set_sample_rates()
error: buffer overflow 'dac->rates' 6 <= 6"
This patch papers over the buggy point, by ensuring that dac->rates[]
update not overflowing the actual array size.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If CONFIG_PM is not defined, then arch/arm/mach-at91/pm.c is not
compiled in. This patch creates an inline function that does nothing
if CONFIG_PM is not defined.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
When the probe of snd-hda-intel driver is deferred due to f/w loading
or the nested module loading, complete_all() should be also delayed
until the initialization really finished. Otherwise, vga-switcheroo
client would start switching before the actual init is done.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
