Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Sink count can change between short pulse hpd hence this patch
adds a member variable to intel_dp so we can track any changes
between short pulse interrupts.
This patch reads sink_count dpcd always and removes its
read operation based on values in downstream port dpcd.
SINK_COUNT dpcd is not dependent on DOWNSTREAM_PORT_PRESENT dpcd.
SINK_COUNT denotes if a display is attached, while
DOWNSTREAM_PORT_PRESET indicates how many ports are available
in the dongle where display can be attached. so it is possible
for sink count to change irrespective of value in downstream
port dpcd.
Here is a table of possible values and scenarios
sink_count downstream_port
present
0 0 no display is attached
0 1 dongle is connected without display
1 0 display connected directly
1 1 display connected through dongle
v2: Storing value of intel_dp->sink_count that is ready
for consumption. (Ander)
Squashing two commits into one. (Ander)
v3: Added comment to explain the need of early return when
sink count is 0. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-4-git-send-email-shubhangi.shrivastava@intel.com
Current DP detection has DPCD operations split across
intel_dp_hpd_pulse and intel_dp_detect which contains
duplicates as well. Also intel_dp_detect is called
during modes enumeration as well which will result
in multiple dpcd operations. So this patch tries
to solve both these by bringing all DPCD operations
in one single function and make intel_dp_detect
use existing values instead of repeating same steps.
v2: Pulled in a hunk from last patch of the series to
this patch. (Ander)
v3: Added MST hotplug handling. (Ander)
v4: Added a flag to check if detect is performed to
prevent multiple detects on hotplug. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[anderco: fix parenthesis aligment]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-2-git-send-email-shubhangi.shrivastava@intel.com
Patch based on a previous series by Shashank Sharma.
v2: Do not read GAMMA_MODE register to figure what mode we're in
v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0
Add documentation on how the Broadcast RGB property is affected by CTM
v4: Update contributors
v5: Refactor degamma/gamma LUTs load into a single function
v6: Fix missing intel_crtc variable (bisect issue)
v7: Fix & simplify limited range matrix multiplication (Matt Roper's
comment)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com
Implement Daniel Stone's recommendation to not read registers to infer
the hardware's state.
v2: Read GAMMA_MODE register value at init (Matt Roper's comment)
v3: Read GAMMA_MODE register in intel_modeset_readout_hw_state along
with other registers (Matt Roper's comment).
v4: Mask GAMMA_MODE register with interesting bits when reading
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-3-git-send-email-lionel.g.landwerlin@intel.com
The moves a couple of functions programming the gamma LUT and CSC
units into their own file.
On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).
The CSC unit is only available from Haswell on.
We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.
v2: Fix access to GAMMA_MODE register on older generations than
Haswell (from Matt Roper's comments)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Split out the part initing the clock gating hooks and move it earlier.
Add a new NOP hook for platforms without the need to apply clockgating
or workaround settings, so that the hook can be called unconditionally.
Also add a WARN for future platforms that forget to add a hook.
The rest of the hooks in intel_init_pm() should be inited in the same
way, but atm some of the hooks are set only conditionally, so before
doing this we need to make the setup unconditional and use instead some
flags.
v2:
- add a NOP hook and WARN if no hook is set for the platform (Chris)
- use the term hook instead of callback for these functions (Jani)
v3:
- remove the GEN4() check it's already covered by earlier platform
checks (Chris)
CC: Jani Nikula <jani.nikula@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-6-git-send-email-imre.deak@intel.com
All of this is SW only initialization so we can move them earlier. Move
the mutex init where the rest of the locks are inited. While at it also
convert dev to dev_priv.
v2:
- use the term hook instead of callback for these functions (Jani)
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-5-git-send-email-imre.deak@intel.com
Whenever there's an update to the primary plane,
fbc_pre_update and fbc_post_update are called. Kill off
intel_crtc->atomic.update_fbc and now that intel_crtc->atomic
is empty, kill it off too.
Changes since v1:
- Add a intel_fbc_supports_rotation helper.
Changes since v2:
- Remove intel_fbc_supports_rotation_helper.
- Remove unrelated changes.
Changes since v3:
- Rebase
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457516145-32117-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
fb_bits is useful to have in the crtc_state for cs flips when
the code is updated to use intel_frontbuffer_flip_prepare/complete.
So calculate it in advance and move it to crtc_state. The other stuff
can be calculated in post_plane_update, and aren't useful elsewhere.
Changes since v1:
- Changing wording, remove comment about loop.
Changes since v2:
- Rebase.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457516145-32117-1-git-send-email-maarten.lankhorst@linux.intel.com
commit 92826fcdfc ("drm/i915: Calculate watermark related members in the crtc_state, v4.")
broke thigns by removing the pre vs. post wm update distinction. We also
lost the pre plane wm update entirely for VLV/CHV from the crtc enable
path.
This caused underruns on modeset and plane enable/disable on CHV,
and often those can lead to a dead pipe.
So let's bring back the pre vs. post thing, and let's toss in an
explicit wm update to valleyview_crtc_enable() to avoid having to
put it into the common code.
This is more or less a partial revert of the offending commit.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 92826fcdfc ("drm/i915: Calculate watermark related members in the crtc_state, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457543247-13987-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Manage the LCPLLs used with DisplayPort, so that all the HSW/BDW DPLLs
are managed by the shared dpll code.
v2: Introduce INTEL_DPLL_ALWAYS_ON flag to please state checker. (Ander)
v3: Initialize pll->flags in intel_shared_dpll_init(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Change the type of intel_crtc_state->shared_dpll to be a pointer to a
shared dpll. With this there is no need to first convert the id stored
in the crtc state to a pointer in order to use it. It does introduce a
bit of hassle on doing the opposite.
The long term objective is to hide details about dpll ids behind the
shared dpll interface.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Create the new file intel_dpll_mgr.c and move the shared dpll code to
it. Follow up patches that reorganize pll handling will move more code
there and tweak the interface.
No functional changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-2-git-send-email-ander.conselvan.de.oliveira@intel.com
In commit 1e657ad7 we moved the last step of firmware initialization to
skl_display_core_init(), where it will be run only during system resume,
but not during driver loading. Since this init step needs to be done
whenever we program the firmware fix this by moving the initialization
to the end of intel_csr_load_program().
While at it simplify a bit csr_load_work_fn().
This issue prevented DC5/6 transitions, this change will re-enable those.
v2:
- remove debugging left-over and redundant comment in csr_load_work_fn()
Fixes: 1e657ad7a4 ("drm/i915/gen9: Write dc state debugmask bits only once")
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457121461-16729-1-git-send-email-imre.deak@intel.com
Generalize rawclk handling by storing it in dev_priv.
Presumably our hrawclk readout works at least for CTG and ELK
since we've been using it for DP AUX on those platforms. There
are no real docs anymore after configdb vanished, so the only
reference is the public CTG GMCH spec. What bits are listed in
that doc match our code. The ELK GMCH spec have no relevant
details unfortunately.
The PNV situation is less clear. Starting from
commit aa17cdb4f8 ("drm/i915: initialize backlight max from VBT")
we assume that the CTG/ELK hrawclk readout works for PNV as well.
At least the results *seem* reasonable for one PNV machine (Lenovo
Ideapad S10-3t). Sadly the PNV GMCH spec doesn't have the goods on
the relevant register either.
So let's keep assuming it works for PNV,ELK,CTG and read it out on
those platforms. G33 also has hrawclk according to some notes
in BSpec, but we don't actually need it for anything, so let's not
even try to read it out there.
v2: Rebase due to IS_VALLYVIEW vs. IS_CHERRYVIEW split
Use KHz() all over, and kill off a few useless temp variables
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456932138-14004-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently the wait_for_atomic_us only allows for a jiffie
timeout granularity which is not nice towards callers
requesting small micro-second timeouts.
Re-implement it so micro-second timeout granularity is really
supported and not just in the name of the macro.
This has another beneficial side effect that it improves
"gem_latency -n 100" results by approximately 2.5% (throughput
and latencies) and 3% (CPU usage). (Note this improvement is
relative to not yet merged execlist lock uncontention patch
which moves the CSB MMIO outside this lock.)
It also shrinks some hot functions like fw_domains_get by a
tiny 3%.
v2:
* Warn when used from non-atomic context (if possible).
* Warn on too long atomic waits.
v3:
* Added comment explaining CONFIG_PREEMPT_COUNT.
* Fixed pre-processor indentation.
(Chris Wilson)
v4:
* Commit msg update (gem_latency) and rebase.
v5:
* Commit message re-wording.
* Added comment about no need for double cond check. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This is for callers who want micro-second precision but are not
waiting from the atomic context.
v2:
* Fix atomic waits. (Dave Gordon)
* Use USEC_PER_SEC and USEC_PER_MSEC. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Only planes that are part of the state should be used for recalculating
watermarks. For planes not part of the state the previous patch allows
us to re-use the old values since they're calculated even for levels
that are not actively used.
Changes since v1:
- Remove big if from intel_crtc_atomic_check.
- Remove extra newline.
- Remove memset in ilk_compute_pipe_wm.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456826842-32553-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Rather than assume the VGA dotclock is really the FDI based thing,
let's read out the real thing via iclkip, and after readout it'll
get to compare it with the FDI based number to make sure they're
in sync.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we check if the encoder's idea of dotclock agrees with what
we calculated based on the FDI parameters. We do this in the encoder
.get_config() hooks, which isn't so nice in case the BIOS (or some other
outside party) made a mess of the state and we're just trying to take
over.
So as a prep step to being able sanitize such a bogus state, move the
the sanity check to just after we've read out the entire state. If
we then need to sanitize a bad state, it should be easier to move the
sanity check to occur after sanitation instead of before it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Instead of repopulatin the rotation_info struct for the fb every time
we try to use the fb, we can just populate it once when creating the fb,
and later we can just copy the pre-populate struct into the gtt_view.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-10-git-send-email-ville.syrjala@linux.intel.com
Throw out a bunch of unnecessary stuff from struct intel_rotation_info,
and pull most of the remaining stuff to live under an array of
per-color plane sub-structures.
What still remains outside the sub-structure will be reorgranized later
as well, but that requires more work elsewhere so leave it be for now.
v2: Split the vma size == luma+chroma size fix to prep patch (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-8-git-send-email-ville.syrjala@linux.intel.com
intel_compute_page_offsets() gets passed a bunch of the framebuffer
metadate sepearately. Just pass the framebuffer itself to make life
simpler for the caller, and make it less likely they would make a
mistake in the order of the arguments (as most as just unsigned ints and
such).
We still pass the pitch explicitly since for 90/270 degree rotation
the caller has to pass in the right thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-7-git-send-email-ville.syrjala@linux.intel.com
intel_pin_and_fence_fb_obj() only needs the framebuffer, and the desird
rotation (to find the right GTT view for it), so no need to pass all
kinds of plane stuff.
The main motivation is to get rid of the uggy NULL plane_state handling
due to fbdev.
v2: Add a note why I really want this
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Grumpily-Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-6-git-send-email-ville.syrjala@linux.intel.com
The page aligned surface address calculation needs to know which way
things are rotated. The contract now says that the caller must pass the
rotate x/y coordinates, as well as the tile_height aligned stride in
the tile_height direction. This will make it fairly simple to deal with
90/270 degree rotation on SKL+ where we have to deal with the rotated
view into the GTT.
v2: Pass rotation instead of bool even thoughwe only care about 0/180 vs. 90/270
v3: Introduce intel_tile_dims(), and don't mix up different units so much
v4: Unconfuse bytes vs. pixels even more
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
v11:
- Now that we've moved to atomic watermark updates, make sure we call
the proper function to program watermarks in
{ironlake,haswell}_crtc_enable(); the failure to do so on the
previous patch iteration led to us not actually programming the
watermarks before turning on the CRTC, which was the cause of the
underruns that the CI system was seeing.
- Fix inverted logic for determining when to optimize watermarks. We
were needlessly optimizing when the intermediate/optimal values were
the same (harmless), but not actually optimizing when they differed
(also harmless, but wasteful from a power/bandwidth perspective).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456276813-5689-1-git-send-email-matthew.d.roper@intel.com
Currently we perform our own wait in post_plane_update,
but the atomic core performs another one in wait_for_vblanks.
This means that 2 vblanks are done when a fb is changed,
which is a bit overkill.
Merge them by creating a helper function that takes a crtc mask
for the planes to wait on.
The broadwell vblank workaround may look gone entirely but this is
not the case. pipe_config->wm_changed is set to true
when any plane is turned on, which forces a vblank wait.
Changes since v1:
- Removing the double vblank wait on broadwell moved to its own commit.
Changes since v2:
- Move out POWER_DOMAIN_MODESET handling to its own commit.
Changes since v3:
- Do not wait for vblank on legacy cursor updates. (Ville)
- Move broadwell vblank workaround comment to page_flip_finished. (Ville)
Changes since v4:
- Compile fix, legacy_cursor_flip -> *_update.
Changes since v5:
- Kill brackets.
- Add WARN_ON when wait_for_vblanks fails.
- Remove extra newlines.
- Split the checks whether vblank is needed to a separate function,
with comments why a vblank is needed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56CD84DA.5030507@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Starting from BDW the DE_PIPE interrupts for pipe B and C belong to the
relevant display power well. So we should make sure we've finished
processing them before turning off the power well.
The pipe interrupts shouldn't really happen at this point anymore since
we've already shut down the planes/pipes/whatnot, but being a bit
paranoid shouldn't hurt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455907651-16397-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Instead of restoring dpms and a flag for whether a temp fb is allocated duplicate
an atomic state before the new state is committed, and commit it the old state
in intel_release_load_detect_pipe.
Changes since v1:
- Use a real atomic state. (Ville)
Changes since v2:
- Do not preserve shared_dpll any more, no need to do so. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-2-git-send-email-maarten.lankhorst@linux.intel.com
We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.
Kudos to Ville and Joonas for the ideas of this new interface.
v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled
CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com
Make resume/on codepath not to wait for panel_power_cycle_delay(t11_t12)
if this time is already spent in suspend/poweron time.
v2: Use CLOCK_BOOTTIME and remove jiffies for panel power cycle
delay calculation(Ville).
v3: Addressed below comments
1. Tracking time from where last powercycle is initiated.
2. Used ktime_get_bootime() wrapper for boottime clock.
3. Used ktime_ms_delta() to get time difference.
v4: Updated v3 change log in detail.
v5: Removed static from panel_power_on_time(Stéphane).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453513144-14135-1-git-send-email-abhay.kumar@intel.com
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.
v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.
v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.
v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
(Imre)
v5: Caching reserved stolen base and size in the driver private data.
Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
intel_uncore_sanitize. (Imre)
v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
earlier in the load.
v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)
v8: Fixed formatting and checkpatch issues. Fixed functional issue where
RC6 ctx size check was missing. (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com
This opens the possibility of implementing nicer schemes to choose the
CRTC, such as checking the amount of stolen memory available, or
choosing the best pipe on platforms that don't die FBC to pipe or
plane A.
This code was written for another refactor that I ended up discarding,
so I don't actually need it, but I figured this patch would be an
improvement on its own so I kept it on the series.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-18-git-send-email-paulo.r.zanoni@intel.com
Older FBC platforms have this restriction where FBC can't be enabled
if multiple pipes are enabled. In the current code, we disable FBC
before the second pipe becomes visible.
One of the problems with this code is that the current
multiple_pipes_ok() implementation just iterates through all CRTCs
looking at their states, but it doesn't make sure that the state
locks are grabbed. It also can't just grab the locks for every CRTC
since this would kill one of the biggest advantages of atomic
modesetting.
After the recent FBC changes, we now have the appropriate locks for
the given CRTC, so we can just try to maintain the state of each CRTC
and update it once intel_fbc_pre_update is called.
As a last note, I don't have gen 2/3 machines to test this code. My
current plan is to enable FBC on just the newer platforms, so this
patch is just an attempt to get the gen 2/3 code at least looking
sane, so if one day someone decide to fix FBC on these platforms, they
may have less work to do.
Not-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (only on HSW+)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-16-git-send-email-paulo.r.zanoni@intel.com
Instead of:
- intel_fbc_disable_crtc(crtc)
- intel_fbc_disable(dev_priv)
we now have:
- intel_fbc_disable(crtc)
- intel_fbc_global_disable(dev_priv)
This is because all the other functions that take a CRTC are called
- intel_fbc_something(crtc)
Instead of:
- intel_fbc_something_crtc(crtc)
And I also hope that the word "global" is going to help make it more
explicit that "global" is the unusual case, not the opposite.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-14-git-send-email-paulo.r.zanoni@intel.com
We'll now call intel_fbc_pre_update instead of intel_fbc_deactivate
during atomic commits. This will continue to guarantee that we
deactivate FBC and it will also update the state checking structures
at the correct time. Then, later, at the point where we were calling
intel_fbc_update, we'll only need to call intel_fbc_post_update.
Also add the proper warnings in case we don't have the appropriate
locks. Daniel mentioned the warnings will have to be removed for async
commits, but let's keep them here while we can.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-12-git-send-email-paulo.r.zanoni@intel.com
Having this on stack triggers the -Wframe-larger-than=1024 and
is not nice to put such big things on the kernel stack anyway.
This required a little bit of refactoring to handle the new
failure path from vlv_force_pll_on.
v2: Corrected some whitespace.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453217117-26125-1-git-send-email-tvrtko.ursulin@linux.intel.com
This reverts commit 396e33ae20.
This commit was triggering some FIFO underrun warnings on ILK-IVB
platforms (but surprisingly not on HSW/BDW that share more or less the
same codepaths). These underruns were caught by the continuous
integration (CI) system and could be reproduced consistently when
running the basic acceptance tests (BAT) on the affected platforms.
Note that this revert will cause a visible regression for some
end-users; the "flicker when mouse moves between monitors in X" issue
that was reported before this patch was merged will now return. However
regressions that are visible to CI have higher priority since they
prevent proper testing of future patches on those platforms. Hopefully
we'll be able to figure out the cause of the underruns quickly and
remerge an improved version of this patch to fix the regression.
Cc: Daniel Vetter <daniel@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93640
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453232584-8543-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since intel_gen4_compute_page_offset() can now handle tiling formats
all the way down to gen2, rename it to intel_compute_tile_offset().
Not that we actually use it on gen2/3 since there's no DSPSURF etc.
registers which would take a page aligned address.
v2: s/page/tile/ (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-7-git-send-email-ville.syrjala@linux.intel.com
I find more usual to think about tile widths than heights, so changing
the intel_tile_height() to calculate the tile height as
tile_size/tile_width is easier than the opposite to the poor brain.
v2: Reorder arguments for consistency
Constify dev_priv arguments
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-4-git-send-email-ville.syrjala@linux.intel.com
Pull the tile width calculations from intel_fb_stride_alignment() into a
new function intel_tile_width().
Also take the opportunity to pass aroun dev_priv instead of dev to
intel_fb_stride_alignment().
v2: Reorder argumnents to be more consistent with other functions
Change intel_fb_stride_alignment() to accept dev_priv instead of dev
v3: Deal with Y tilling (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-3-git-send-email-ville.syrjala@linux.intel.com
They're causing massive amounts of dmesg noise and hence CI noise all
over the place. Enabling them for a bit was good enough to refresh our
task list of what's still needed to enable rpm by default.
To make sure we're not forgetting to make this noisy again add a FIXME
comment.
Fixes: da5827c366 ("drm/i915: add assert_rpm_wakelock_held helper")
Cc: Imre Deak <imre.deak@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1452012847-4737-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
(cherry picked from commit becd9ca2de)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than having open coded checks for the DDI A/E configuration,
just store the max supported lane count in intel_digital_port.
We had an open coded check for DDI A, but not for DDI E. So we may
have been vilating the DDI E max lane count.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't use plane->state directly, use the pointer from commit_plane.
Changes since v1:
- Fix uses of plane->state->rotation and color key to use the passed state too.
- Only pass crtc_state and plane_state to update_plane.
Changes since v2:
- Rebased.
Changes since v3:
- Small whitespace changes and only assign 1 variable per line.
- Constify plane_state and crtc_state. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452164052-21752-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452108870-24204-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
They're causing massive amounts of dmesg noise and hence CI noise all
over the place. Enabling them for a bit was good enough to refresh our
task list of what's still needed to enable rpm by default.
To make sure we're not forgetting to make this noisy again add a FIXME
comment.
Fixes: da5827c366 ("drm/i915: add assert_rpm_wakelock_held helper")
Cc: Imre Deak <imre.deak@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1452012847-4737-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On skylake when calculating plane visibility with the crtc in
dpms off mode the real cdclk may be different from what it would be
if the crtc was active. This may result in a WARN_ON(cdclk < crtc_clock)
from skl_max_scale. The fix is to keep a atomic_cdclk that would be true
if all crtc's were active.
This is required to get the same calculations done correctly regardless
of dpms mode.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447945645-32005-12-git-send-email-maarten.lankhorst@linux.intel.com
Parallel modesets are still not allowed, but this will allow updating
a different crtc during a modeset if the clock is not changed.
Additionally when all pipes are DPMS off the cdclk will be lowered
to the minimum allowed.
Changes since v1:
- Add dev_priv->active_crtcs for tracking which crtcs are active.
- Rename min_cdclk to min_pixclk and move to dev_priv.
- Add a active_crtcs mask which is updated atomically.
- Add intel_atomic_state->modeset which is set on modesets.
- Commit new pixclk/active_crtcs right after state swap.
Changes since v2:
- Make the changes related to max_pixel_rate calculations more readable.
Changes since v3:
- Add cherryview and missing WARN_ON to readout.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
In some cases we want to check whether we hold an RPM wakelock reference
for the whole duration of a sequence. To achieve this add a new RPM
atomic sequence counter that we increment any time the wakelock refcount
drops to zero. Check whether the sequence number stays the same during
the atomic section and that we hold the wakelock at the beginning of the
section.
Motivated by Chris.
v2-v3:
- unchanged
v4:
- swap the order of atomic_read() and assert_rpm_wakelock_held() in
assert_rpm_atomic_begin() to avoid race
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-10-git-send-email-imre.deak@intel.com
Atm, we assert that the device is not suspended until the point when the
device is truly put to a suspended state. This is fine, but we can catch
more problems if we check that RPM refcount is non-zero. After that one
drops to zero we shouldn't access the device any more, even if the actual
device suspend may be delayed. Change assert_rpm_wakelock_held()
accordingly to check for a non-zero RPM refcount in addition to the
current device-not-suspended check.
For the new asserts to work we need to annotate every place explicitly in
the code where we expect that the device is powered. The places where we
only assume this, but may not hold an RPM reference:
- driver load
We assume the device to be powered until we enable RPM. Make this
explicit by taking an RPM reference around the load function.
- system and runtime sudpend/resume handlers
These handlers are called when the RPM reference becomes 0 and know the
exact point after which the device can get powered off. Disable the
RPM-reference-held check for their duration.
- the IRQ, hangcheck and RPS work handlers
These handlers are flushed in the system/runtime suspend handler
before the device is powered off, so it's guaranteed that they won't
run while the device is powered off even though they don't hold any
RPM reference. Disable the RPM-reference-held check for their duration.
In all these cases we still check that the device is not suspended.
These explicit annotations also have the positive side effect of
documenting our assumptions better.
This caught additional WARNs from the atomic modeset path, those should
be fixed separately.
v2:
- remove the redundant HAS_RUNTIME_PM check (moved to patch 1) (Ville)
v3:
- use a new dedicated RPM wakelock refcount to also catch cases where
our own RPM get/put functions were not called (Chris)
- assert also that the new RPM wakelock refcount is 0 in the RPM
suspend handler (Chris)
- change the assert error message to be more meaningful (Chris)
- prevent false assert errors and check that the RPM wakelock is 0 in
the RPM resume handler too
- prevent false assert errors in the hangcheck work too
- add a device not suspended assert check to the hangcheck work
v4:
- rename disable/enable_rpm_asserts to disable/enable_rpm_wakeref_asserts
and wakelock_count to wakeref_count
- disable the wakeref asserts in the IRQ handlers and RPS work too
- update/clarify commit message
v5:
- mark places we plan to change to use proper RPM refcounting with
separate DISABLE/ENABLE_RPM_WAKEREF_ASSERTS aliases (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450227139-13471-1-git-send-email-imre.deak@intel.com
As a preparation for follow-up patches add a new helper that checks
whether we hold an RPM reference, since this is what we want most of
the cases. Atm this helper will only check for the HW suspended state, a
follow-up patch will do the actual change to check the refcount instead.
One exception is the forcewake release timer function, where it's
guaranteed that the HW is on even though the RPM refcount drops to zero.
This guarantee is provided by flushing the timer in the runtime suspend
handler. So leave the assert_device_not_suspended check in place there.
Also rename assert_device_suspended for consistency and export these
helpers as a preparation for the follow-up patches.
No functional change.
v3:
- change the assert warning message to be more meaningful (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1450203038-5150-6-git-send-email-imre.deak@intel.com
The vma may have been rebound between the last time the cursor was
enabled and now, so skipping the cursor gtt offset deduction is not
safe unless we would also reset cursor_bo to NULL when disabling the
cursor. Just thow cursor_bo to the bin instead since it's lost all
other uses thanks to universal plane support.
Chris pointed out that cursor updates are currently too slow
via universal planes that micro optimizations like these wouldn't
even help.
v2: Add a note about futility of micro optimizations (Chris)
Cc: drm-intel-fixes@lists.freedesktop.org
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/082976.html
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450107302-17171-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Here are the patchset to add get_eld op to audio component for
communicating more directly between i915 and HD-audio.
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
The commits are based on Dave's latest drm-next branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=NShN
-----END PGP SIGNATURE-----
Merge tag 'drm-i915-get-eld' of tiwai/sound into drm-intel-next-queued
Add get_eld audio component for i915/HD-audio
Currently, the HDMI/DP audio status and ELD are notified and obtained
via the hardware-level communication over HD-audio unsolicited event
and verbs although the graphics driver holds the exactly same
information. As we already have a notification via audio component,
this is another step forward; namely, the audio driver may fetch
directly the audio status and ELD via the new component op.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Implement a new i915_audio_component_ops, get_eld(). It's called by
the audio driver to fetch the current audio status and ELD of the
given HDMI/DP port. It returns the size of expected ELD bytes if it's
valid, zero if no valid ELD is found, or a negative error code. The
current state of audio on/off is stored in the given pointer, too.
Note that the returned size isn't limited to the given max bytes. If
the size is greater than the max bytes, it means that only a part of
ELD has been copied back.
For achieving this implementation, a new field audio_connector is
added to struct intel_digital_port. It points to the connector
assigned to the given digital port. It's set/reset at each audio
enable/disable call in intel_audio.c, and protected with av_mutex.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for DP MST audio in i915.
Enable audio codec when DP MST is enabled if has_audio flag is set.
Disable audio codec when DP MST is disabled if has_audio flag is set.
Another separated patches to support DP MST audio will be implemented
in audio driver.
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449036584-105393-2-git-send-email-libin.yang@linux.intel.com
This removes pre/post_wm_update from intel_crtc->atomic, and
creates atomic state for it in intel_crtc.
Changes since v1:
- Rebase on top of wm changes.
Changes since v2:
- Split disable_cxsr into a separate patch.
Changes since v3:
- Move some of the changes to intel_wm_need_update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56603A49.5000507@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to call FBC enable/disable only once per modeset, while
activate/deactivate/update will be called multiple times.
The enable() function will be responsible for deciding if a CRTC will
have FBC on it and then it will "lock" FBC on this CRTC: it won't be
possible to change FBC's CRTC until disable(). With this, all checks
and resource acquisition that only need to be done once per modeset
can be moved from update() to enable(). And then the update(),
activate() and deactivate() code will also get simpler since they
won't need to worry about the CRTC being changed.
The disable() function will do the reverse operation of enable(). One
of its features is that it should only be called while the pipe is
already off. This guarantees that FBC is stopped and nothing is
using the CFB.
With this, the activate() and deactivate() functions just start and
temporarily stop FBC. They are the ones touching the hardware enable
bit, so HW state reflects dev_priv->crtc.active.
The last function remaining is update(). A lot of times I thought
about renaming update() to activate() or try_to_activate() since it's
called when we want to activate FBC. The thing is that update() may
not only decide to activate FBC, but also deactivate or keep it on the
same state, so I'll leave this name for now.
Moving code to enable() and disable() will also help in case we decide
to move FBC to pipe_config or something else later.
The current patch only puts the very basic code on enable() and
disable(). The next commits will take care of moving more stuff from
update() to the new functions.
v2:
- Rebase.
- Improve commit message (Chris).
v3: Rebase after changing the patch order.
v4: Rebase again after upstream changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
The long term goal is to have enable/disable as the higher level
functions and activate/deactivate as the lower level functions, just
like we do for PSR and for the CRTC. This way, we'll run enable and
disable once per modeset, while update, activate and deactivate will
be run many times. With this, we can move the checks and code that
need to run only once per modeset to enable(), making the code simpler
and possibly a little faster.
This patch is just the first step on the conversion: it starts by
converting the current low level functions from enable/disable to
activate/deactivate. This patch by itself has no benefits other than
making review and rebase easier. Please see the next patches for more
details on the conversion.
v2:
- Rebase.
- Improve commit message (Chris).
v3: Rebase after changing the patch order.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
There's no need to reevaluate the status of every single crtc when a
single crtc changes its state.
With this, we're cutting the case where due to a change in pipe B,
intel_fbc_update() is called, then intel_fbc_find_crtc() concludes FBC
should be enabled on pipe A, then it completely rechecks the state of
pipe A only to conclude FBC should remain enabled on pipe A. If any
change on pipe A triggers a need to recompute whether FBC is valid on
pipe A, then at some point someone is going to call
intel_fbc_update(PIPE_A).
The addition of intel_fbc_deactivate() is necessary so we keep track
of the previously selected CRTC when we do invalidate/flush. We're
also going to continue the enable/disable/activate/deactivate concept
in the next patches.
v2: Rebase.
v3: Rebase after changing the patch order.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/
The .get_config() hooks should not reference anything in crtc->config,
everything should be based on the passed in pipe_config instead. So
don't dig out the cpu_transcoder from crtc->config on ddi platfforms,
and also avoid using the encoder->crtc link and instead look up the
pipe via pipe_config->base.crtc.
I don't think this will actually fix anything since during the initial
state readout we set up the encoder->crtc link prior to calling
.get_config(), and during the modeset state check the encoder->crtc
ought to be correct anyway since it's that state we just programmed.
But this seems the right thing to do anyway.
While at it, do some house cleaning on the local variables in the
.infoframe_enabled() hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448555227-31403-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-11-20-rebased:
4 weeks because of my vacation, so a bit more:
- final bits of the typesafe register mmio functions (Ville)
- power domain fix for hdmi detection (Imre)
- tons of fixes and improvements to the psr code (Rodrigo)
- refactoring of the dp detection code (Ander)
- complete rework of the dmc loader and dc5/dc6 handling (Imre, Patrik and
others)
- dp compliance improvements from Shubhangi Shrivastava
- stop_machine hack from Chris to fix corruptions when updating GTT ptes on bsw
- lots of fifo underrun fixes from Ville
- big pile of fbc fixes and improvements from Paulo
- fix fbdev failures paths (Tvrtko and Lukas Wunner)
- dp link training refactoring (Ander)
- interruptible prepare_plane for atomic (Maarten)
- basic kabylake support (Deepak&Rodrigo)
- don't leak ringspace on resets (Chris)
drm-intel-next-2015-10-23:
- 2nd attempt at atomic watermarks from Matt, but just prep for now
- fixes all over
* tag 'drm-intel-next-2015-11-20-merged' of git://anongit.freedesktop.org/drm-intel: (209 commits)
drm/i915: Update DRIVER_DATE to 20151120
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: take a power domain ref only when needed during HDMI detect
drm/i915: Tear down fbdev if initialization fails
async: export current_is_async()
Revert "drm/i915: Initialize HWS page address after GPU reset"
drm/i915: Fix oops caused by fbdev initialization failure
drm/i915: Fix i915_ggtt_view_equal to handle rotation correctly
drm/i915: Stuff rotation params into view union
drm/i915: Drop return value from intel_fill_fb_ggtt_view
drm/i915 : Fix to remove unnecsessary checks in postclose function.
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Remove platform specific *_dp_detect() functions
drm/i915: Don't do edp panel detection in g4x_dp_detect()
drm/i915: Send TP1 TP2/3 even when panel claims no NO_TRAIN_ON_EXIT.
drm/i915: PSR: Don't Skip aux handshake on DP_PSR_NO_TRAIN_ON_EXIT.
drm/i915: Reduce PSR re-activation time for VLV/CHV.
drm/i915: Delay first PSR activation.
drm/i915: Type safe register read/write
...
DSI has quite a few special cases, like DP, so add it to crtc
state. This way we can get rid of a number of intel_pipe_has_type()
checks for DSI. This isn't necessarily the prettiest way, but it's a
step towards being aligned with what's being done with other encoders.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448619706-21293-3-git-send-email-jani.nikula@intel.com
I noticed that intel_fbdev->our_mode is unused. Introduced by
79e539453b ("DRM: i915: add mode setting support").
Then I noticed that intel_fbdev->fbdev_list is unused as well.
Introduced by 386516744b ("drm/fb: fix fbdev object model +
cleanup properly.") in i915, nouveau and radeon.
Subsequently cargo culted to amdgpu, ast, cirrus, qxl, udl,
virtio and mgag200.
Already removed from the latter with cc59487a05 ("drm/mgag200:
'fbdev_list' in 'struct mga_fbdev' is not used").
Remove it from the others.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
Replace the is_sdvob bool and some sdvo_reg checks with enum port. This
makes the SDVO code look more modern, and gets rid of explicit register
offset checks in the code which will hamper register type checking.
v2: Add assert_sdvo_port_valid() (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446838199-3666-1-git-send-email-ville.syrjala@linux.intel.com
It was created at 'commit aabc95dcf2 (drm/i915: Dont -ETIMEDOUT
on identical new and previous (count, crc).")' becase the counter
wasn't reliable.
Now that we properly wait for the counter to be reset we can rely
a bit more in the counter.
Also that patch stopped to return -ETIMEDOUT so the test case is
unable to skip when it is unreliable and end up in many fails
that should be skip instead.
So, with the counter more reliable we can remove
this hack that just makes things more confusing when test cases
are really expecting the same CRC and let test case skip if that's
not the case.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-1-git-send-email-patrik.jakobsson@linux.intel.com
We need to initialize the display core part early, before initializing
the rest of the display power state. This is also described in the bspec
termed "Display initialization sequence". Atm we run this sequence
during driver loading after power domain HW state initialization which
is too late and during runtime suspend/resume which is unneeded and can
interere with DMC functionality which handles HW resources toggled
by this init/uninit sequence automatically. The init sequence must be
run as the first step of HW power state initialization and during
system resume. The uninit sequence must be run during system suspend.
To address the above move the init sequence to the initial HW power
state setup and the uninit sequence to a new power domains suspend
function called during system suspend.
As part of the init sequence we also have to reprogram the DMC firmware
as it's lost across a system suspend/resume cycle.
After this change CD clock initialization during driver loading will
happen only later after other dependent HW/SW parts are initialized,
while during system resume it will get initialized as the last step of
the init sequence. This distinction can be removed by some refactoring
of platform independent parts. I left this refactoring out from this
series since I didn't want to change non-SKL parts. This is a TODO for
later.
v2:
- fix error path in i915_drm_suspend_late()
- don't try to re-program the DMC firmware if it failed to load
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447774433-20834-1-git-send-email-imre.deak@intel.com
Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().
The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.
So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.
v2 (from Paulo):
- Write a commit message since the original patch left it empty.
- Rebase after the intel_power_well_{en,dis}able rename.
- Use lookup_power_well() instead of hardcoded indexes.
Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
Rather than computing on demand, store also the aux data reg
offsets under intel_dp.
v2: Duplicate some code to make things less magic (Jani)
v3: Use PORT_B registers for invalid ports in g4x_aux_data_reg()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-6-git-send-email-ville.syrjala@linux.intel.com
As all csr firmware related opertion are not using any
any data structures of drm framework level, so better to
use dev_priv instead of dev. it's a new style! :)
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-9-git-send-email-imre.deak@intel.com
This removes two anti-patterns:
- Locking shouldn't be used to synchronize with async work (of any
form, whether callbacks, workers or other threads). This is what the
mutex_lock/unlock seems to have been for in intel_csr_load_program.
Instead ordering should be ensured with the generic
wait_for_completion()/complete(). Or more specific functions
provided by the core kernel like e.g.
flush_work()/cancel_work_sync() in the case of synchronizing with a
work item.
- Don't invent own completion like the following code did with the
(already removed) wait_for(csr_load_status_get()) pattern - it's
really hard to get these right when you want them to be _really_
correct (and be fast) in all cases. Furthermore it's easier to read
code using the well-known primitives than new ones using
non-standard names.
Before enabling/disabling DC6 check if the firmware is loaded
successfully. This is guaranteed during runtime s/r, since otherwise we
don't enable RPM, but not during system s/r.
Note that it's still unclear whether we need to enable/disable DC6
during system s/r, until that's clarified, keep the current behavior and
enable/disable DC6.
Also after this patch there is a race during system s/r where the
firmware may not be loaded yet, that's addressed in an upcoming patch.
v2-v3:
- unchanged
v4:
- rebased on latest drm-intel-nightly
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: added code and note about checking if the firmware loaded ok,
before enabling/disabling it]
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447341037-2623-1-git-send-email-imre.deak@intel.com
Avoids non-static functions since all the callers are in intel_rpm.c.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[imre: removed note about reg definitions from commit message, since
it's not relevant any more]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
[Jani: make assert_csr_loaded static]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-4-git-send-email-imre.deak@intel.com
Reading the driver load/unload code leaves one confused as there's
an async_schedule() in the load, but not async_synchronize_full()
in sight. In fact it's hidden inside intel_fbdev.c. So let's move the
async_schedule() into intel_fbdev.c as well so that it's next to the
async_synchronize_full(), which should make the relationship easier
to see.
Plus this way we won't schedule a nop function call when fbdev is
disabled. And we were passing a pointer to a static inline
function to async_schedule(), which seems rather dubious to me.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446815313-9490-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Doing the IBX transcoder B workaround causes underruns on
pipe/transcoder A. Just hide them by disabling underrun reporting for
pipe A around the workaround.
It might be possible to avoid the underruns by moving the workaround
to be applied only when enabling pipe A. But I was too lazy to try it
right now, and the current method has been proven to work, so didn't
want to change it too hastily.
Note that this can re-enable underrun reporting on pipe A if was
already disabled due to a previous actual underrun. But that's OK, we
may just get a second underrun report if another real underron occurrs
on pipe A.
v2: Note that pipe A underruns can get re-enabled due to this (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1446225802-11180-1-git-send-email-ville.syrjala@linux.intel.com
Due to the shared error interrupt on IVB/HSW and CPT/PPT we may not
always get an interrupt on a FIFO underrun. But we can always do an
explicit check (like we do on GMCH platforms that have no underrun
interrupt).
v2: Drop stale kerneldoc for i9xx_check_fifo_underruns() (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1446225741-11070-1-git-send-email-ville.syrjala@linux.intel.com
VMA offsets are 64 bits. Plane surface offsets are in ggtt and
the hardware register to set this is thus 32 bits. Be explicit
about these and convert carefully to from vma to final size.
This will make sparse happy by not creating 32bit pointers out
of 64bit vma offsets.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446204375-29831-1-git-send-email-mika.kuoppala@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
In order to prepare for a link training with DDI, the state machine
would call intel_ddi_prepare_link_retrain(). To remove the dependency to
the hardware information, replace that direct call with a callback.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445594525-7174-7-git-send-email-ander.conselvan.de.oliveira@intel.com
I wanted to add yet another check to intel_fbc_update() and realized
I would need to create yet another enum no_fbc_reason case. So I
remembered this patch series that Damien wrote a long time ago and
nobody ever reviewed, so I decided to reimplement it since the code
changed a lot since then.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445964628-30226-2-git-send-email-paulo.r.zanoni@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Make pinning and waiting a separate step, and wait for object idle
without struct_mutex held.
Changes since v1:
- Do not wait when a reset is in progress.
- Remove call to i915_gem_object_wait_rendering for
intel_overlay_do_put_image (Chris Wilson)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Move it from intel_crtc_atomic_commit to prepare_plane_fb.
Waiting is done before committing, otherwise it's too late
to undo the changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59561/
A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.
While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.
v2: Don't move cxsr_allowed to state (Maarten)
v3: Only calculate watermarks in state. Still keep active watermarks in
intel_crtc itself. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/59556/
The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update. However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call. Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60372/
Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.
Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Smoke-tested-by: Paulo Zanoni <przanoni@gmail.com>
Link: http://patchwork.freedesktop.org/patch/60367/
Previously rotation was ignored and wrong stride programmed
into the plane registers resulting in a corrupt image on screen.
v2: Do not access potentialy old plane state at flip time,
but store the rotation value at the time of queing the flip.
(Ville)
v3: No need to pass rotation to intel_queue_mmio_flip since it
is available in the crtc. (Ville)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Testcase: igt/kms_rotation_crc/primary-rotation-90-flip-stress (SKL)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially in cases where pre-os does not enable display, cdclk might
not be in sane state. During sanitization initialize cdclk with maximum
value till we get dynamic cdclk support.
v2: Check if BIOS programmed correctly rather than always calling init
- Do validation of programmed cdctl and what it is expected
- Only do slk_init_cdclk if validation failed else reuse BIOS
programmed value
v3: Move the validation logic in a separate sanitize function (Ville)
v4: No need to check LCPLL after sanitize and use max_cdclk_freq instead
of hardcoded value (Ville)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445344992-14658-1-git-send-email-shobhit.kumar@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
atomic->disabled_planes is a hack that had to exist because
prepare_fb was only called when a new fb was set. This messed
up fb tracking in some circumstances like aborts from
interruptible waits. As a result interruptible waiting in
prepare_plane_fb was forbidden, but other errors could still
cause frontbuffer tracking to be messed up.
Now that prepare_fb is always called, this hack is no longer
required and prepare_fb may fail without consequences.
Changes since v1:
- Clean up a few fb tracking warnings by changing plane->fb to
plane->state->fb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mmio register access after dc6/dc5 entry is not allowed when
DC6 power states are enabled according to bspec (bspec-id 0527),
so enabling dc6 as the last call in suspend flow.
Addtional note from Imre:
Currently we keep DC6 enabled during modesets and DPAUX transfers, which
is not allowed according to the specification. This can lead at least to
PLL locking failures, DPAUX timeouts and prevent deeper package power
states (PC9/10). Fix this for now by enabling DC6 only when we know the
above events (modeset, DPAUX) can't happen.
This a temporary solution as some issues are still unsolved as described
in [1] and [2], we'll address those as a follow-up.
[1]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077669.html
[2]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077787.html
v1: Initial version.
v2: Based on review comment from Daniel,
- created a seperate patch for csr uninitialization set call.
v3: Rebased on top of latest code.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a squash of the following commits:
Revert "drm/i915: Drop intel_update_sprite_watermarks"
This reverts commit 47c99438b5.
Revert "drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check"
This reverts commit 7809e5ae35.
Revert "drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v3)"
This reverts commit 3a05f5e2e7.
With these reverts, SKL finally stops failing every single FBC test
with FIFO underrun error messages. After some brief testing, it also
seems that this commit prevents the machine from completely freezing
when we run igt/kms_fbc_crc (see fd.o #92355).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92355
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's been reported that the atomic watermark series triggers some
regressions on SKL, which we haven't been able to track down yet. Let's
temporarily revert these patches while we track down the root cause.
This commit squashes the reverts of:
76305b1 drm/i915: Calculate watermark configuration during atomic check (v2)
a4611e4 drm/i915: Don't set plane visible during HW readout if CRTC is off
a28170f drm/i915: Calculate ILK-style watermarks during atomic check (v3)
de4a9f8 drm/i915: Calculate pipe watermarks into CRTC state (v3)
de165e0 drm/i915: Refactor ilk_update_wm (v3)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077190.html
Cc: "Zanoni, Paulo R" <paulo.r.zanoni@intel.com>
Cc: "Vetter, Daniel" <daniel.vetter@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.
While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.
v2: Don't move cxsr_allowed to state (Maarten)
v3: Only calculate watermarks in state. Still keep active watermarks in
intel_crtc itself. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update. However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call. Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.
Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle the HDMI aspect ratio property the same way in the SDVO code
as we handle it in the HDMI code.
v2: Remove stray whitespace change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The vblank counts are u32 so make flip_queued_vblank and
flip_ready_vblank u32 as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for NV12 support.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I only tested this on BDW and SKL, but since the register description
is the same ever since gen4, let's assume that all gens take the same
register format. If that's not true, then hopefully someone will
bisect a bug to this patch and we'll fix it.
Notice that the wrong fence offset register just means that the
hardware tracking will be wrong.
Testcases:
- igt/kms_frontbuffer_tracking/fbc-1p-primscrn-pri-shrfb-draw-mmap-gtt
- igt/kms_frontbuffer_tracking/fbc-2p-primscrn-pri-shrfb-draw-mmap-gtt
v2:
- Add intel_crtc->adjusted_{x,y} so this code can work independently
of intel_gen4_compute_page_offset(). (Ville).
- This version also works on SKL.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Instead of doing a hack during primary plane commit the state
is updated during atomic evasion. It handles differences in
pipe size and the panel fitter.
This is continuing on top of Daniel's work to make faster
modesets atomic, and not yet enabled by default.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet:
- simplify/future-proof if ladder that Jesse spotted
- resolve conflict in pipe_config_check and don't spuriously move the
code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the intel_connector initialized to intel_hdmi
display, during the init phase, just like the other encoders do.
This attachment is very useful when we need to extract the connector
pointer during the hotplug handler function
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7a
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a251 drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add vlv_dport_to_phy() and fix up the return values of
vlv_dport_to_channel() and vlv_pipe_to_channel() to use
the appropriate enums.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.
Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Due to the way busy_bits was handled, we were not doing any flushes if
we didn't previously get an invalidate. Since it's possible to get
flushes without an invalidate first, remove the busy_bits early
return.
So now that we don't have the busy_bits guard anymore we'll need the
origin check for the GTT tracking (we were not doing anything on GTT
flushes due to the GTT check at invalidate()).
As a last detail, since we can get multiple consecutive flushes,
disable FBC before updating it, otherwise intel_fbc_update() will just
keep FBC enabled instead of restarting it.
Notice that this does not fix any of the current IGT tests due to the
fact that we still have a few intel_fbc() calls at points where we
also have the frontbuffer tracking calls: we didn't fully convert to
frontbuffer tracking yet. Once we remove those calls and start relying
only on the frontbuffer tracking infrastructure we'll need this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crystalcove pmic support from Shobhit. Patch series has all acks/r-bs from
other mainainers so ok to pull into drm-next. But I'm cc'ing all other
maintainers as fyi and in case they want to pull it into their trees too
to avoid conflicts.
* tag 'topic/crc-pmic-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
mfd: Add GPIOLIB dependency if INTEL_SOC_PMIC is to be enabled
drm/i915: Backlight control using CRC PMIC based PWM driver
drm/i915: Use the CRC gpio for panel enable/disable
pwm: crc: Add Crystalcove (CRC) PWM driver
mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM
mfd: intel_soc_pmic_crc: Add PWM cell device for Crystalcove PMIC
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal
gpiolib: Add support for removing registered consumer lookup table
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we both set mode->private_flags to some value and also use
the pipe_config quirk. But since the pipe_config quirk isn't tied to
the lifetime of the mode object we need to check both.
Simplify this by only using mode.private_flags and stop using the
INHERITED_MODE quirk. Also for clarity add an explicit #define for
that driver priavete mode flag.
By using crtc_state->mode_changed we can also remove the recalc local
variable.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can only fail because of a bug in the code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Squash in follow-up to also remove start_vbl_count from
intel_crtc->atomic and put it into the intel_crtc directly - it's not
precomputed state.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous commit converted hw readout to atomic, all the new_*
members were used for restoring the old state, but with the
conversion of suspend to atomic there's no use left for them.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All non-primary planes get disabled during hw readout,
this reduces complexity and means not having to do some plane
visibility checks during the first commit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing depends on this outside initial hw readout, so keep this
struct on the stack instead.
Changes since v1:
- Remove unrelated changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's not much point for calculating the changes for the old
state. Instead just disable all scalers when disabling. It's
probably good enough to just disable the crtc_scaler, but just in
case there's a bug disable all scalers.
This means intel_atomic_setup_scalers is only called in the crtc
check function now, so all the transitional code can be removed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since flush actually means invalidate + flush we need to force psr
exit on PSR flush.
On Core platforms there is no way to disable hw tracking and
do the pure sw tracking so we simulate it by fully disable psr and
reschedule a enable back.
So a good idea is to minimize sequential disable/enable in cases we
know that HW tracking like when flush has been originated by a flip.
Also flip had just invalidated it already.
It also uses origin to minimize the a bit the amount of
disable/enabled, mainly when flip already had invalidated.
With this patch in place it is possible to do a flush on dirty areas
properly in a following patch.
v2: Remove duplicated exit on HSW+Sprites as pointed out by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.
This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.
While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The frontbuffer code gives us accurate information about activity,
let's use it. Again this should avoid unecessary updates when multiple
screens are on.
Also realign function paramaters, I couldn't resist that bit of OCD.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The current/old frontbuffer might still have gpu frontbuffer rendering
pending. But once flipped it won't have the corresponding frontbuffer
bits any more and hence the request retire function won't ever clear
the corresponding busy bits. The async flip tracking (with the
flip_prepare and flip_complete functions) already does this, but
somehow I've forgotten to do this for synchronous flips.
Note that we don't track outstanding rendering of the new framebuffer
with busy_bits since all our plane update code waits for previous
rendering to complete before displaying a new buffer. Hence a new
buffer will never be busy.
v2: Drop the spurious inline Ville spotted.
v3: Don't touch flip_bits in the synchronsou frontbuffer_flip
function, noticed by Paulo.
v4: Remove one more inline that slipped through (Paulo).
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testcase: igt/kms_frontbuffer_tracking/fbc-modesetfrombusy
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch doesn't have any functional change, but organize fruntbuffer
invalidate and busy by removing unecesarry signature argument for ring.
It was unsed on mark_fb_busy and only used on fb_obj_invalidate for the
same ORIGIN_CS usage. So let's clean it a bit
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By making color key atomic there are no more transitional helpers.
The plane check function will reject the color key when a scaler is
active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the initial state, and add a quirk to force add all planes
to crtc_state->plane_mask during initial commit. This will disable
all planes during the initial modeset.
The initial plane quirk is temporary, and will go away when hardware
readout is fully atomic, and the watermark updates in intel_sprite.c
are removed.
Changes since v1:
- Unset state->visible on !primary planes.
- Do not rely on the plane->crtc pointer in intel_atomic_plane,
instead assume planes are invisible until modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is probably intended to be be done during vblank evasion.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The idea was good, but planes can have a fb even though
they're disabled. This makes the force argument useless
and always true, because only the commit function updates
state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By passing crtc_state to the check_plane functions a lot of duplicated
code can be removed. There are still some transitional helper calls,
they will be removed later.
Changes since v1:
- Revert state->visible changes.
- Use plane->state->crtc instead of plane->crtc.
- Use drm_atomic_get_existing_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes it easier to verify that no changes are done when
calling this from crtc instead.
Changes since v1:
- Make intel_wm_need_update static and always check it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of a whole lot of ternary operators and assign the index
in scaler_id, instead of the id. They're the same thing.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit has two main advantages: simplify intel_fbc_update()
and deduplicate the strings.
v2:
- Rebase due to changes on P1.
- set_no_fbc_reason() can now return void (Chris).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently intel_gen4_compute_page_offset() simply picks the closest
page boundary below the linear offset. That however may not be suitably
aligned to satisfy any hardware specific restrictions. So let's make
sure the page boundary we choose is properly aligned.
Also to play it a bit safer lets split the remaining linear offset into
x and y values instead of just x. This should make no difference for
most platforms since we convert the x and y offsets back into a linear
offset before feeding them to the hardware. HSW+ are different however
and use x and y offsets even with linear buffers, so they might have
trouble if either the x or y get too big.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.
Seems it introduces regressions for 3 different reasons, oh boy..
In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.
In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.
In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.
It's better to fix those issues first, and then commit this patch,
so do that temporarily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This needs to be done last after all modesets have been calculated.
A modeset first disables all crtc's, so any crtc that undergoes a
modeset counts as inactive.
If no modeset's done, or > 1 crtc's stay w/a doesn't apply.
Apply workaround on the first crtc if 1 crtc stays active.
Apply workaround on the second crtc if no crtc was active.
Changes since v1:
- Use intel_crtc->atomic as a place to put hsw_workaround_pipe.
- Make sure quirk only applies to haswell.
- Use first loop to iterate over newly enabled crtc's only.
This increases readability.
Changes since v2:
- Move hsw_workaround_pipe back to crtc_state.
Changes since v3:
- Return errors from haswell_mode_set_planes_workaround.
Changes since v4:
- Clean up commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.
Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Assume the callers lock everything with drm_modeset_lock_all.
This change had to be done after converting suspend/resume to
use atomic_state so the atomic state is preserved, otherwise
all transitional state is erased.
Now all callers of .crtc_enable and .crtc_disable go through
atomic modeset! :-D
Changes since v1:
- Only check for crtc_state->active in valleyview_modeset_global_pipes.
- Only check for crtc_state->active in modeset_update_crtc_power_domains.
Changes since v2:
- Rework on top of the changed patch order.
Changes since v3:
- Rename intel_crtc_toggle in description to *_control
- Change return value to int.
- Do not add plane state, should be done implicitly already.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To make this work we load the new hardware state into the
atomic_state, then swap it with the sw state.
This lets us change the force restore path in setup_hw_state()
to use a single call to intel_mode_set() to restore all the
previous state.
As a nice bonus this kills off encoder->new_encoder,
connector->new_enabled and crtc->new_enabled. They were used only
to restore the state after a modeset.
Changes since v1:
- Make sure all possible planes are added with their crtc set,
so they will be turned off on first modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we can subclass drm_atomic_state we can also use it to keep
track of all the pll settings. atomic_state is a better place to hold
all shared state than keeping pll->new_config everywhere.
Changes since v1:
- Assert connection_mutex is held.
Changes since v2:
- Fix swapped arguments to kzalloc for intel_atomic_state_alloc. (Jani Nikula)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Having a single path for everything makes it a lot easier to keep
crtc_state->active in sync with intel_crtc->active.
A crtc cannot be changed to active when not enabled, because it means
no mode is set and no connectors are connected.
This should also make intel_crtc->active match crtc_state->active.
Changes since v1:
- Reworded commit message, there's no intel_crtc_toggle.
Changes since v2:
- Change some callers of intel_crtc_control to intel_display_suspend.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.
Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the pll updates are staged the put_shared_dpll function
consists only of checks that are done in check_shared_dpll_state
after a modeset too.
The changes to pll->config are overwritten by
intel_shared_dpll_commit, so this entire function is a noop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The primary plane frobbing was removed from the sprite code in
commit ecce87ea3a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit 536f5b5e86
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake nv12 format requires dbuf (aka. ddb) calculations
and programming for each of y and uv sub-planes. Made minor
changes to reuse current dbuf calculations and programming
for uv plane. i.e., with this change, existing computation
is used for either packed format or uv portion of nv12
depending on incoming format. Added new code for dbuf
computation and programming for y plane.
This patch is a pre-requisite for adding NV12 format support.
Actual nv12 support is coming in later patches.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is no longer necessary since we only update the staged config on
successfull modeset. The new configuration is stored in an atomic state
struct which is freed in case of failure.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes disabling planes more explicit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[anderco: fixed warning due to using drm_crtc instead of intel_crtc]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're the same code, so why not?
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was an optimization from way back before we had primary plane
support to be able to disable the primary plane. But with primary
plane support userspace can tell the kernel this directly, so there's
no big need for this any more. And it's getting in the way of the
atomic conversion.
If need be we can resurrect this later on properly again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Explain why removing this is ok.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used by the next commit to disable all planes on a crtc
without caring what type it is.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some of the flags that were used are still useful when transitioning
to atomic, so keep those around for now. This removes some of the
complications of crtc->primary_enabled, making it easier to remove.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updates the EDID compliance test function to perform the analyze and react to
the EDID data read as a result of a hot plug event. The results of this
analysis are handed off to userspace so that the userspace app can set the
display mode appropriately for the test result/response.
The compliance_test_active flag now appears at the end of the individual
test handling functions. This is so that the kernel-side operations can
be completed without the risk of interruption from the userspace app
that is polling on that flag.
V2:
- Addressed mailing list feedback
- Removed excess debug messages
- Removed extraneous comments
- Fixed formatting issues (line length > 80)
- Updated the debug message in compute_edid_checksum to output hex values
instead of decimal
V3:
- Addressed more list feedback
- Added the test_active flag to the autotest function
- Removed test_active flag from handler
- Added failsafe check on the compliance test active flag
at the end of the test handler
- Fixed checkpatch.pl issues
V4:
- Removed the checksum computation function and its use as it has been
rendered superfluous by changes to the core DRM EDID functions
- Updated to use the raw header corruption detection mechanism
- Moved the declaration of the test_data variable here
V5:
- Update test active flag variable name to match the change in the
first patch of the series.
- Relocated the test active flag declaration and initialization
to this patch
V6:
- Updated to use the new flag for raw EDID header corruption
- Removed the extra EDID read from the autotest function
- Added the edid_checksum variable to struct intel_dp so that the
autotest function can write it to the sink device
- Moved the update to the hpd_pulse function to another patch
- Removed extraneous constants
V7:
- Fixed erroneous placement of the checksum assignment. In some cases
such as when the EDID read fails and is NULL, this causes a NULL ptr
dereference in the kernel. Bad news. Fixed now.
V8:
- Updated to support the kfree() on the EDID data added previously
V9:
- Updated for the long_hpd flag propagation
V10:
- Updated to use actual checksum from the EDID read that occurs during
normal hot plug path execution
- Removed variables from intel_dp struct that are no longer needed
- Updated the patch subject to more closely match the nature and contents
of the patch
- Fixed formatting problem (long line)
V11:
- Removed extra debug messages
- Updated comments to be more informative
- Removed extra variable
V12:
- Removed the 4 bit offset of the resolution setting in compliance data
- Changed to DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER
Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a first of series patches that optimize DP link
training. The first patch is for eDP only where we reuse
the previously trained link training values from cache
i.e. voltage swing and pre-emphasis levels.
In case we are not able to train the link by reusing
the known values, the link training parameters are set
to zero and training is restarted.
V2:
- flag that indicates if DP link is trained and valid
renamed from 'link_trained' to 'train_set_valid'
- removed routine 'intel_dp_reuse_link_train'
V3:
- rebased against the latest drm-intel-nightly
V4:
- removed HPD long pulse handling for eDP case to clear the
flag that indicates to reuse the current link training
parameters. (based on Sivakumar's comment)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[danvet: s/DP/eDP/ in subject to make scope clear.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by scripts/coccinelle/api/err_cast.cocci
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.
v2: Removed camelcase in functions and variables.
v3: Do some minimal check to assert if CSR program is not loaded.
v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
new ones.
4] Changed variable names as updated in earlier patches.
v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.
v6: Remove use of dc5_enabled variable as it's no longer needed.
v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.
v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.
Also call POSTING_READ for every write to a register to ensure that
its written immediately.
v1: Remove POSTING_READ calls as they've already been added in previous patches.
v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.
Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
to warnings. However, removing them for now as they'll be included in a future patch
asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
accessed during deferred DC5-enabling, are not initialized earlier.
v3: Rebase to latest.
Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5 for simplicity, instead of
deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.
v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.
v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.
v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)
v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.
v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.
This implementation is added based on first version of DMC CSR program
that we received from h/w team.
Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.
For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.
As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.
v1: Initial relese as RFC patch
v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.
v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.
v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.
v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.
Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.
v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.
v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.
v8: Rebase to latest.
v9: Rebase on top of -nightly (Damien)
v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)
v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)
v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)
v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)
v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)
v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)
v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)
Issue: VIZ-2569
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables skylake primary plane scaling using shared
scalers atomic desgin.
v2:
-use single copy of scaler limits (Matt)
v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)
v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)
v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
is using drm_plane->state rect instead of intel_plane->state rect.
This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
Added helper functions for refactoring are comprehended enough to be
used for skylake_update_plane (for sprite) too. One stop towards
having single function for all planes.
v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
The merge is clean, but the arm build fails afterwards,
due to API changes in the regulator tree.
I've included the patch into the merge to fix the build.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have grown a number of different implementations of
DIV_ROUND_CLOSEST_ULL throughout the kernel. Move the i915 one to
kernel.h so that it can be reused.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Reviewed-by: Jeff Epler <jepler@unpythonic.net>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the skeleton framework for supporting automation for Displayport compliance
testing. This patch adds the necessary framework for the source device to
appropriately respond to test automation requests from a sink device.
V2:
- Addressed previous mailing list feedback
- Fixed compilation issue (struct members declared in a later patch)
- Updated debug messages to be more accurate
- Added status checks for the DPCD read/write calls
- Removed excess comments and debug messages
- Fixed debug message compilation warnings
- Fixed compilation issue with missing variables
- Updated link training autotest to ACK
V3:
- Fixed the checks on the DPCD return code to be <= 0
rather than != 0
- Removed extraneous assignment of a NAK return code in the
DPCD read failure case
- Changed the return in the DPCD read failure case to a goto
to the exit point where the status code is written to the sink
- Removed FAUX test case since it's deprecated now
- Removed the compliance flag assignment in handle_test_request
V4:
- Moved declaration of type_type here
- Removed declaration of test_data (moved to a later patch)
- Added reset to 0 for compliance test variables
V5:
- Moved test_active variable declaration and initialization out of
this patch and into the patch where it's used
- Changed variable name compliance_testing_active to
compliance_test_active to unify the naming convention
- Added initialization for compliance_test_type variable
Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VSwing programming sequence as specified in the updated BXT BSpec
v2: Satheesh's review comments addressed.
- clear value before setting into registers
- move print statement to bxt function
Other changes
- since signal level will not be set into DDI_BUF_CTL, the value need
not be returned to intel_dp_set_signal_levels(). Making the bxt
specific function to return void and setting signal_levels = 0 for
bxt inside intel_dp_set_signal_levels()
- instead of signal levels, printing vswing level and pre-emphasis
level
- in case none of the pre-emphasis levels or vswing levels are set,
setting default of 400mV + 0dB
v3: Satheesh's review comments
- Check for mask before printing signal_levels.
- Removing redundant register writes
- Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT
- Making register write part generic as it will be required for HDMI as
well.
Re-structure the code to include an array for vswing related values, set
signal levels
v4: Satheesh's review comments
- Rebase over latest renaming patches
- use hsw_signal_levels for HAS_DDI
Other changes
- Modified vswing_sequence() func definition
- Rebased on top of register macro definitions
v5: Satheesh's review comments
- Check ddi translation table size
v6: Imre's review comments
- removed comments in vswing sequence
- added vswing, pre-emphasis prints in intel_dp_set_signal_levels
- added comment explaining use of DP vswing values for eDP
- initialize n_entries and ddi_transaltion table based on encoder type
- create bxt_ddi_buf_trans structure and use decimal values
- adding a flag in bxt buffer translation table to indicate def entry
v7: (imre)
- squash in Vandana's "VSwing register definition",
"HDMI VSwing programming", "Re-enable vswing programming",
"Fix vswing sequence" patches
- use BXT_PORT_* regs directly instead of via a temp var
- simplify BXT_PORT_* macro definitions
- add code comment why we read lane while write group registers
- fix readout of DP_TRAIN_PRE_EMPHASIS in debug message
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Assign PLL for pipe (dependent on port attached to the pipe)
v2:
- fix incorrect encoder vs. new_encoder check for crtc (imre)
v3:
- warn and return error if no encoder is attached (imre)
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't move intel_ddi_get_crtc_new_encoder around.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Modified as per review comments from Imre
- Mention enabling instead of allowing in the debug trace and
remove unnecessary comments.
v3:
- Rebase to latest.
- Move DC9-related functions from intel_display.c to intel_runtime_pm.c.
v4: (imre)
- remove DC5 disabling, it's a nop at this point
- squashed in Suketu's "Assert the requirements to enter or exit DC9"
patch
- remove check for RUNTIME_PM from assert_can_enable_dc9, it's not a
dependency
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v3)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add PHY specific display initialization sequence as per BSpec.
Note that the PHY initialization/uninitialization are done
at their current place only for simplicity, in a future patch - when more
of the runtime PM features will be enabled - these will be moved to
power well#1 and modeset encoder enabling/disabling hooks respectively.
The call to uninitialize the PHY during system/runtime suspend will be
added later in this patchset.
v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set
v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- fix DDI PHY timeout value
- squash in Vandana's "PORT_CL2CM_DW6_A BUN fix",
"DDI PHY programming register defn", "Do ddi_phy_init always",
- move PHY register macros next to the corresponding CHV/VLV macros
- move DE PLL register macros here from another patch since they are
used here first
- add BXT_ prefix to CDCLK flags
- s/COMMON_RESET/COMMON_RESET_DIS/ and clarify related code comments
- fix incorrect read value for the RMW of BXT_PHY_CTL_FAMILY_DDI
- fix using GT_DISPLAY_EDP_POWER_ON vs. GT_DISPLAY_DDI_POWER_ON
when powering on DDI ports
- fix incorrect port when setting BXT_PORT_TX_DW14_LN for DDI ports
- add missing masking when programming CDCLK_FREQ_DECIMAL
- add missing powering on for DDI-C port, rename OCL2_LDOFUSE_PWR_EN
to OCL2_LDOFUSE_PWR_DIS to reduce confusion
- add note about mismatch with bspec in the PORT_REF_DW6 fields
- factor out PHY init code to a new function, so we can call it for
PHY1 and PHY0, instead of open-coding the same
v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
accordingly
- use the existing dpio_phy enum instead of adding a new one for the
same purpose
- flip the meaning of PHYs so that PHY_A is PHY1 and PHY_BC is PHY0 to
better match CHV
- s/BXT_PHY/_BXT_PHY/
- use _PIPE for _BXT_PHY instead of open-coding it
- drop _0_2_0_GTTMMADR suffix from BXT_P_CR_GT_DISP_PWRON
- define GT_DISPLAY_POWER_ON in a more standard way
- make a note that the CHV ConfigDB also disagrees about GRC_CODE field
definitions
- fix lane optimization refactoring fumble from v3
- add per PHY uninit functions to match the init counterparts
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add CDCLK specific display clock initialization sequence as per BSpec.
Note that the CDCLK initialization/uninitialization are done at their
current place only for simplicity, in a future patch - when more of the
runtime PM features will be enabled - these will be moved to power
well#1 and modeset encoder enabling/disabling hooks respectively. This
also means that atm dynamic power gating power well #1 is effectively
disabled.
The call to uninitialize CDCLK during system/runtime suspend will be
added later in this patchset.
v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set
v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- move DE PLL register macros here from another patch since they are
used here first
- add BXT_ prefix to CDCLK flags
- add missing masking when programming CDCLK_FREQ_DECIMAL
v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
accordingly
- s/DISPLAY_PCU_CONTROL/HSW_PCODE_DE_WRITE_FREQ_REQ/
- simplify BXT_DE_PLL_RATIO macros
- fix BXT_DE_PLL_RATIO_MASK
- s/bxt_select_cdclk_freq/broxton_set_cdclk_freq/
- move cdclk init/uninit/set code from intel_ddi.c to intel_display.c
- remove redundant code comments for broxton_set_cdclk_freq()
- sanitize fixed point<->integer frequency value conversion
- use DRM_ERROR instead of WARN
- do RMW when programming BXT_DE_PLL_CTL for safety
- add note about PLL lock timeout being exactly 200us
- make PCU error messages more descriptive
- instead of using 0 freq to mean PLL off/bypass freq use 19200
for clarity, as the latter one is the actual rate
- simplify pcode programming, removing duplicated
sandybridge_pcode_write() call
- sanitize code flow, remove unnecessary scratch vars in
broxton_set_cdclk() (imre)
- Remove bound check for maxmimum freq to match current code.
This check will be added later at a more proper platform
independent place once atomic support lands.
- add note to remove freq guard band which isn't needed on BXT
- add note to reduce freq to minimum if no pipe is enabled
- combine broxton_modeset_global_pipes() with
valleyview_modeset_global_pipes()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to spec: "In PSR HW or SW mode, SW set this bit before writing
registers for a flip. It will be self-clear when it gets to the PSR
active state."
Some versions of spec mention that this is needed when in
"Persistent mode" but define it as same as "SW mode". Since this
fix the page flip case let's assume this is exactly what we need.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
Broken by
commit 944b0c7657
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Mar 20 16:18:07 2015 +0200
drm/i915: Copy the staged connector config to the legacy atomic state
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enabling skylake panel fitting feature using shared scalers
v2:
-added force detach parameter for pfit disable purpose (me)
-read crtc scaler state from hw state (Daniel)
-replaced both skylake_pfit_enable and disable with skylake_pfit_update (me)
-added scaler id check to intel_pipe_config_compare (Daniel)
v3:
-updated function header to kerneldoc format (Matt)
-dropped need_scaling checks (Matt)
v4:
-move clearing of scaler id from commit path to check path (Matt)
-updated colorkey checks based on recent updates (me)
-squashed scaler check while enabling colorkey to here (me)
-use values in plane_state->src as regular integers (me)
-changes made not to modify state in commit path (Matt)
v5:
-squashed helper function to update scaler users to here (Matt)
-squashed helper function to detach scaler to here (Matt, me)
-changes to align with updated scaler structures (Matt, me)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added intel_atomic_setup_scalers to setup scalers based on
staged scaling requests from a crtc and its planes. If staged
requests are supportable, this function assigns scalers to
requested planes and crtc. Note that the scaler assignement
itself is staged into crtc_state and respective plane_states
for later commit after all checks have been done.
overall high level flow:
- scaler requests are staged into crtc_state by planes/crtc
- check whether staged scaling requests can be supported
- add planes using scalers that aren't in current transaction
- assign scalers to requested users
- as part of plane commit, scalers will be committed
(i.e., either attached or detached) to respective planes in hw
- as part of crtc_commit, scaler will be either attached or detached
to crtc in hw
crtc_compute_config calls intel_atomic_setup_scalers() to start
scaler assignments as per scaler state in crtc config. This call
should be moved to atomic crtc once it is available.
v2:
-removed a log message (me)
-changed input parameter to crtc_state (me)
v3:
-remove assigning plane_state returned by drm_atomic_get_plane_state (Matt)
-fail if there is an error from drm_atomic_get_plane_state (Matt)
v4:
-changes to align with updated scaler structure (Matt, me)
v5:
-added addtional checks before enabling HQ mode (me)
-added comments to enable HQ mode (Matt)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
skylake scaler structure definitions. scalers live in crtc_state as
they are pipe resources. They can be used either as plane scaler or
panel fitter.
scaler assigned to either plane (for plane scaling) or crtc (for panel
fitting) is saved in scaler_id in plane_state or crtc_state respectively.
scaler_id is used instead of scaler pointer in plane or crtc state
to avoid updating scaler pointer everytime a new crtc_state is created.
v2:
-made single copy of min/max values for scalers (Matt)
v3:
-updated commentary for scaler_id (me)
v4:
-converted src/dst ranges to #defines, dropped ratios (Matt)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.
v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: Nicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Moving creation of property in a function, checking for 90/270
rotation simultaneously (Chris)
Letting primary plane to be positioned
v3: Adding if/else for 90/270 and rest params programming, adding check for
pixel_format, some cleanup (review comments)
v4: Adding right pixel_formats, using src_* params instead of crtc_* for offset
and size programming (Ville)
v5: Rebased on -nightly and Tvrtko's series for gtt remapping.
v6: Rebased on -nightly (Tvrtko's series merged)
v7: Moving pixel_format check to intel_atomic_plane_check (Matt)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With boosting for missed pageflips, we have a much stronger indication
of when we need to (temporarily) boost GPU frequency to ensure smooth
delivery of frames. So now only allow each client to perform one RPS boost
in each period of GPU activity due to stalling on results.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we hit a vblank and see that have a pageflip queue but not yet
processed, ensure that the GPU is running at maximum in order to clear
the backlog. Pageflips are only queued for the following vblank, if we
miss it, there will be a visible stutter. Boosting the GPU frequency
doesn't prevent us from missing the target vblank, but it should help
the subsequent frames hitting theirs.
v2: Reorder vblank vs flip-complete so that we only check for a missed
flip after processing the completion events, and avoid spurious boosts.
v3: Rename missed_vblank
v4: Rebase
v5: Cancel the outstanding work in runtime suspend
v6: Rebase
v7: Rebase required fixing
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Deepak S<deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not needed anymore, now that all the users were converted to using
an atomic state.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unify the HSW/BDW/SKL cdclk extraction code to conform to the same
.get_display_clock_speed() mold that all the other platforms
use.
v2: Update due to SKL code getting added
v3: Rebase on top of -nightly (introduction of intel_audio.c) (Mika Kahola)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add v3 note as suggested by Damien.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's completely unused and Tommi noticed that the #define is borked
since forever. I've done a git search in userspace and only found
broken definitions and no users anywhere.
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
For now this is not necessary since intel_set_mode() doesn't acquire any
new locks. However, once that function is converted to atomic, that will
change, since we'll pass an atomic state to it, and that needs to have
the right acquire context set.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of getting the crtc state with drm_atomic_get_crtc_state()
and then converting it to intel_crtc_state will repeat quite often in
the following patches, so add a helper function to save some typing.
v2: Fix upcasting so that crtc_state base field could be moved. (Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Pass in rotation info to sprite plane updates as well.
v3: Use helper to determine 90/270 rotation. (Michel Thierry)
v4: Rebased for fb modifiers and atomic changes.
For: VIZ-4546
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v3)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to do this in order to support 90/270 rotated display.
v2: Pass in drm_plane instead of plane index to intel_obj_display_address.
v3:
* Renamed intel_obj_display_address to intel_plane_obj_offset.
(Chris Wilson)
* Simplified rotation check to bitwise AND. (Chris Wilson)
v4:
* Extracted 90/270 rotation check into a helper function. (Michel Thierry)
v5:
* Rebased for ggtt view changes.
For: VIZ-4545
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
90/270 rotated scanout needs a rotated GTT view of the framebuffer.
This is put in a separate VMA with a dedicated ggtt view and wired such that
it is created when a framebuffer is pinned to a 90/270 rotated plane.
Rotation is only possible with Yb/Yf buffers and error is propagated to
user space in case of a mismatch.
Special rotated page view is constructed at the VMA creation time by
borrowing the DMA addresses from obj->pages.
v2:
* Do not bother with pages for rotated sg list, just populate the DMA
addresses. (Daniel Vetter)
* Checkpatch cleanup.
v3:
* Rebased on top of new plane handling (create rotated mapping when
setting the rotation property).
* Unpin rotated VMA on unpinning from display plane.
* Simplify rotation check using bitwise AND. (Chris Wilson)
v4:
* Fix unpinning of optional rotated mapping so it is really considered
to be optional.
v5:
* Rebased for fb modifier changes.
* Rebased for atomic commit.
* Only pin needed view for display. (Ville Syrjälä, Daniel Vetter)
v6:
* Rebased after preparatory work has been extracted out. (Daniel Vetter)
v7:
* Slightly simplified tiling geometry calculation.
* Moved rotated GGTT view implementation into i915_gem_gtt.c (Daniel Vetter)
v8:
* Do not use i915_gem_obj_size to get object size since that actually
returns the size of an VMA which may not exist.
* Rebased for ggtt view changes.
v9:
* Rebased after code review changes on the preceding patches.
* Tidy function definitions. (Joonas Lahtinen)
For: VIZ-4726
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v4)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Plane state carries the rotation information which is needed for determining
the appropriate GGTT view type.
This just adds the parameter with the actual usage coming in future patches.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be used in a later patch and also convert all height parameters
from int to unsigned int.
v2: Rebased for fb modifiers.
v3: Fixed v2 rebase.
v4:
* Height should be unsigned int.
* Make it take pixel_format for consistency and simplicity.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
msleep() can sleep for way too long, so switch wait_for() to use
usleep_range() instead. Following a totally unscientific method
I just picked the range as W-2W.
This cuts the i915 init time on my BSW to almost half:
- initcall i915_init+0x0/0xa8 [i915] returned 0 after 419977 usecs
+ initcall i915_init+0x0/0xa8 [i915] returned 0 after 238419 usecs
Note that I didn't perform any other benchmarks on this so far.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the colorkey in intel_plane and kill off all the RMW stuff
handling it.
This is just an intermediate step and eventually the colorkey needs to
be converted into some properties.
v2: Actually update the hardware state in the set_colorkey ioctl (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_plane->obj is not used anymore so kill it. Also don't pass both
the fb and obj to the sprite .update_plane() hook, as just passing the fb
is enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite commit 31685c258e
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 3 17:33:01 2014 -0400
drm/i915/vlv: WA for Turbo and RC6 to work together.
Other than code clarity, the major improvement is to disable the extra
interrupts generated when idle. However, the reclocking remains rather
slow under the new manual regime, in particular it fails to downclock as
quickly as desired. The second major improvement is that for certain
workloads, like games, we need to combine render+media activity counters
as the work of displaying the frame is split across the engines and both
need to be taken into account when deciding the global GPU frequency as
memory cycles are shared.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To keep things clear rename the intel_dp->supported_rates[] to
intel_dp->sink_rates[], and rename the supported_rates[] name we used
elsewhere for the intersection of source and sink rates to
common_rates[].
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that intel_dp_max_link_bw() no longer considers the source
restrictions we may try to enable MST with 5.4GHz even when the source
doesn't support it. To fix that switch the code over to handle the link
rate in the same way as the SST code handles it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Consider the link rates reported by the sink via
DP_SUPPORTED_LINK_RATES when checking modes against the max link
rate.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in converting from hardware format every single time, just
store the rates in the final format under intel_dp.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While we only need to restore pipe B/C interrupt registers on BDW when
enabling the power well, skylake a bit more flexible and we'll also need
to restore the pipe A registers as it has its own power well that can be
toggled.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently, this has never worked reliably and is currently disabled. Also, the
gains are not particularly impressive. Thus rather than try to keep unused code
from decaying and having to update it for other driver changes, it was decided
to simply remove it.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDp 1.4 supports custom frequencies.
Skylake supports following intermediate frequencies : 3.24 GHz, 2.16 GHz and
4.32 GHz along with usual LBR, HBR and HBR2 frequencies.
Read sink supported frequencies and get common frequencies from sink and
source and use these for link training.
v2: Rebased, removed calculation of min_clock since for edp it is taken as
max_clock (as per comment).
v3: Keeping single array for link rates (Satheesh)
v4: Setting LINK_BW_SET to 0 when setting LINK_RATE_SET (Satheesh)
v5: Some minor nits (Ville)
v6: Keeping separate arrays for source and sink rates (Ville)
v7: Remove redundant setting of DP_LINK_BW_SET to 0 (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Using DP_SUPPORTED_LINK_RATES macro for supported_rates array (Satheesh).
v3: Reading dpcd's supported link rates tables based upon edp version in the
same patch.
v4: Move version check under is_edp (Satheesh)
v5: Using le16 for rates, some naming, and removing nested if block (Ville)
v6: Correctly using DP_MAX_SUPPORTED_RATES and removing DP_SUPPORTED_LINK_RATES
(Ville)
v7: Incorrectly removed DP_SUPPORTED_LINK_RATES in v6, re-adding it
v8: Checking return value of intel_dp_dpcd_read_wake() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the blt/render tracking we currently have and use the frontbuffer
tracking infrastructure.
Don't enable things by default yet.
v2: (Rodrigo) Fix small conflict on rebase and typo at subject.
v3: (Paulo) Rebase on RENDER_CS change.
v4: (Paulo) Rebase.
v5: (Paulo) Simplify: flushes don't have origin (Daniel).
Also rebase due to patch order changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to port FBC to the frontbuffer tracking infrastructure, but
for that we need to know what caused the object invalidation so
we can react accordingly: CPU mmaps need manual, GTT mmaps and
flips don't need handling and ring rendering needs nukes.
v2: - s/ORIGIN_RENDER/ORIGIN_CS/ (Daniel, Rodrigo)
- Fix copy/pasted wrong documentation
- Rebase
v3: - Rebase
v4: - Don't pass the operation to flushes (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor size fields in intel_crtc just duplicate the data from
cursor->state.crtc_{w,h} so we don't need them any more. Worse, their
use in the watermark code actually introduces a subtle bug since they
don't get updated to mirror the state values until the plane commit
stage, which is *after* we've already used them to calculate new
watermark values. This happens because we had to move watermark updates
slightly earlier (outside vblank evasion) in commit
commit 32b7eeec4d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Wed Dec 24 07:59:06 2014 -0800
drm/i915: Refactor work that can sleep out of commit (v7)
Dropping the intel_crtc fields and just using the state values (which
are properly updated by the time watermark updates happen) should solve
the problem.
Aside from the actual removal of the struct fields (which are formatted
in a way that I couldn't figure out how to match in Coccinelle), the
rest of this patch was generated via the following semantic patch:
// Drop assignment
@@
struct intel_crtc *C;
struct drm_plane_state S;
@@
(
- C->cursor_width = S.crtc_w;
|
- C->cursor_height = S.crtc_h;
)
// Replace usage
@@
struct intel_crtc *C;
expression E;
@@
(
- C->cursor_width
+ C->base.cursor->state->crtc_w
|
- C->cursor_height
+ C->base.cursor->state->crtc_h
|
- to_intel_crtc(E)->cursor_width
+ E->cursor->state->crtc_w
|
- to_intel_crtc(E)->cursor_height
+ E->cursor->state->crtc_h
)
v2: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89346
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Display watermarks need different programming for different tiling
modes.
Set the relevant flag so this happens during the plane commit and
add relevant data into a structure made available to the watermark
computation code.
v2: Pass in tiling info to sprite plane updates as well.
v3: Rebased for plane handling changes.
v4: Handle fb == NULL when plane is disabled.
v5: Refactored for addfb2 interface.
v6: Refactored for fb modifier changes.
v7: Updated for atomic commit by only updating watermarks when tiling changes.
v8: BSpec watermark calculation updates.
v9: Restrict scope of y_tile_minimum variable. (Damien Lespiau)
v10: Get fb from plane state otherwise we are working on old state.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v9)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake is able to scannout those tiling formats. We need to allow them
in the ADDFB ioctl and tell the harware about it.
v2: Rebased for addfb2 interface. (Tvrtko Ursulin)
v3: Rebased for fb modifier changes. (Tvrtko Ursulin)
v4: Don't allow Y tiled fbs just yet. (Tvrtko Ursulin)
v5: Check for stride alignment and max pitch. (Tvrtko Ursulin)
v6: Simplify maximum pitch check. (Ville Syrjälä)
v7: Drop the gen9 check since requirements are no different. (Ville Syrjälä)
v8: Gen2 has different X tiling stride. (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v7)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Till Gen 7 we have two sets of M_N registers, but Gen 8 onwards
we have only one M_N register set. To support DRRS on both scenarios
a input parameter to intel_dp_set_m_n is added.
In case of DRRS, When platform provides two set of M_N registers for dp,
we can program them with two different dividers and switch between them.
But when only one such register set is provided, we have to program
the required divider M_N value on that registers itself.
Two enum members M1_N1 and M2_N2 are defined to represent the above
scenarios.
M1_N1 : Program dp_m_n on M1_N1 registers
dp_m2_n2 on M2_N2 registers (If supported)
M2_N2 : Program dp_m2_n2 on M1_N1 registers
M2_N2 registers are not supported
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is not used outside of intel_display.c since;
commit cf4c7c1225
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Thu Dec 4 10:27:42 2014 -0800
drm/i915: Make all plane disables use 'update_plane' (v5)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was introduced in:
commit 0bc12bcb1b
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Fri Nov 14 08:52:28 2014 -0800
drm/i915: Introduce intel_psr.c
But the unpack function is unused at this date.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is only used in intel_dp.c since:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There have been quite a bit of development lately, leaving behing lonely
protypes. Time to bid them farewell.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this we can treat the fb format modifier completely independently
from the fencing mode in obj->tiling_mode in the initial plane code.
Which means new tiling modes without any gtt fence are now fully
support in the core i915 driver code.
v2: Also add pixel_format while at it, we need this to compute the
height for the new tiling formats.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
At the moment we use crtc->base.primary->fb to hold the initial
framebuffer allocation, disregarding if it's valid or not.
This lead to believe we were actually updating the fb at this point, but
it's not true and we haven't even called drm_framebuffer_init() on this
fb.
Instead, let's store the state in struct intel_initial_plane_config
until we know we can reuse that framebuffer.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter spotted a bug while reviewing some of my refactoring in this
are of the code. I'll quote:
"""
> @@ -9764,6 +9768,7 @@ static int intel_crtc_page_flip(struct drm_crtc *crtc,
> work->event = event;
> work->crtc = crtc;
> work->old_fb_obj = intel_fb_obj(old_fb);
> + work->old_tiling_mode = to_intel_framebuffer(old_fb)->tiling_mode;
Hm, that's actually an interesting bugfix - currently userspace could be
sneaky and destroy the old fb immediately after the flip completes and the
change the tiling of the underlying object before the unpin work had a
chance to run (needs some fudgin with rt prios to starve workers to make
this work though).
Imo the right fix is to hold a reference onto the fb and not the
underlying gem object. With that tiling is guaranteed not to change.
"""
This patch tries to implement the above proposed change.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The atomic helpers need these to prepare a new state object when
starting a new atomic operation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.
For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core. Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.
v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the top-level atomic entrypoints for check/commit. These won't get
called yet; we still need to either enable the atomic ioctl or switch to
using the non-transitional atomic helpers for legacy operations.
v2:
- Use plane->pipe rather than plane->possible_crtcs while ensuring that
only a single CRTC is in use. Either way will work fine since i915
drm_plane's are always tied to a single CRTC, but plane->pipe is
slightly more intuitive. (Ander)
- Simplify crtc/connector checking logic. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we flip on the DRIVER_ATOMIC bit, the DRM core will start calling
this entrypoint to set and lookup driver-specific plane property values,
rather than maintaining a shadow copy in object->properties.
Note that although we add these functions to the plane vtable, they will
not yet be called. Future patches that switch our .set_property()
handler and/or enable full atomic functionality are required before
these code paths will be executed.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of the previous refactoring/consolidation of plane code has resulted
in intel_primary_plane_funcs, intel_cursor_plane_funcs, and
intel_sprite_plane_funcs being identical. Replace all of these with a
single 'intel_plane_funcs' vtable for simplicity.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Runtime state that can be manipulated via properties should now go in
intel_plane_state/drm_plane_state so that it can be tracked as part of
an atomic transaction.
We add a new 'intel_create_plane_state' function so that the proper
initial value for this property (and future properties) doesn't have to
be repeated at each plane initialization site.
v2:
- Stick rotation in common drm_plane_state rather than
intel_plane_state. (Daniel)
- Add intel_create_plane_state() to consolidate the places where we
have to set initial state values. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calls have been added to invalidate/flush DRRS whenever invalidate/flush is
called as part of frontbuffer tracking.
Apart from calls as a result of GEM tracking to fb invalidate/flush, a
call has been added to invalidate fb obj from crtc_page_flip as well. This
is to track busyness through flip calls.
The call to fb_obj_invalidate (in flip) is placed before queuing flip for this
obj.
drrs_invalidate() and drrs_flush() check for drrs.dp which would be NULL if
it was setup in drrs_enable(). This covers for the condition when DRRS is
not supported.
v2: Removing the call to invalidate_drrs from page_flip.
This has not been tested on Android yet, but, in case DRRS transtions do not
work as expected, check by adding back this call in page_flip.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling enable/disable DRRS when enable/disable DDI are called.
These functions are responsible for setup of drrs data (in enable) and
reset of drrs (in disable).
has_drrs is true when downclock_mode is found and SEAMLESS_DRRS is set in
the VBT. A check has been added for has_drrs in these functions, to make
sure the functions go through only if DRRS will work on the platform with
the attached panel.
V2: [By Ram]: WARN_ON is used when intel_edp_drrs_enable() is called more than
once [Rodrigo]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Self-explanatory code is better code.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This vfunc and related structure are only used for fast boot, so let's
rename them to not take them as general purpose ones.
v2: Fix conflicts caused by the introduction of struct intel_crtc_state
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we need to change the fb height constraints, it sounds like a good
idea to have to do it in one place only.
v2: v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than having "tiled" meaning "is it X-tiled?" convert the field to
explicitely store the tiling mode. The code doesn't have to change much
as 1 is conveniently I915_TILING_X.
This is to accommodate future changes around tiling modes and scannout
buffers.
v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous patch changed the config field in intel_crtc to a pointer,
but to keep the mechanical changes (done with spatch) separate from the
new code, the pointer was made to point to a new _config field with type
struct intel_crtc_state added to that struct. This patch improves that
code by getting rid of that field, allocating a state struct in
intel_crtc_init() a keeping it properly updated when a mode set
happens.
v2: Manual changes split from previous patch. (Matt)
Don't leak the current state when the crtc is destroyed (Matt)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[danvet: Squash in fixup from Matt Roper for driver unload.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reduces the number of direct users of crtc->new_config, opening up
the possibilty of removing it altogether.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Earlier, DRRS structures were specific to eDP (used only in intel_dp).
Since DRRS can be extended to other internal display types
(if the panel supports multiple RR), modifying structures
to be part of drm_i915_private and have a provision to add display related
structs like intel_dp.
Also, aligning with frontbuffer tracking mechanism, the new structure
contains data for busy frontbuffer bits.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- refactor i915/snd-hda interaction to use the component framework (Imre)
- psr cleanups and small fixes (Rodrigo)
- a few perf w/a from Ken Graunke
- switch to atomic plane helpers (Matt Roper)
- wc mmap support (Chris Wilson & Akash Goel)
- smaller things all over
* tag 'drm-intel-next-2015-01-17' of git://anongit.freedesktop.org/drm-intel: (40 commits)
drm/i915: Update DRIVER_DATE to 20150117
i915: reuse %ph to dump small buffers
drm/i915: Ensure the HiZ RAW Stall Optimization is on for Cherryview.
drm/i915: Enable the HiZ RAW Stall Optimization on Broadwell.
drm/i915: PSR link standby at debugfs
drm/i915: group link_standby setup and let this info visible everywhere.
drm/i915: Add missing vbt check.
drm/i915: PSR HSW/BDW: Fix inverted logic at sink main_link_active bit.
drm/i915: PSR VLV/CHV: Remove condition checks that only applies to Haswell.
drm/i915: VLV/CHV PSR needs to exit PSR on every flush.
drm/i915: Fix kerneldoc for i915 atomic plane code
drm/i915: Don't pretend SDVO hotplug works on 915
drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV
drm/i915: Remove I915_HAS_HOTPLUG() check from i915_hpd_irq_setup()
drm/i915: Make hpd arrays big enough to avoid out of bounds access
Revert "drm/i915/chv: Use timeout mode for RC6 on chv"
drm/i915: Improve HiZ throughput on Cherryview.
drm/i915: Reset CSB read pointer in ring init
drm/i915: Drop unused position fields (v2)
drm/i915: Move to atomic plane helpers (v9)
...
Backmerge Linus tree after rc5 + drm-fixes went in.
There were a few amdkfd conflicts I wanted to avoid,
and Ben requested this for nouveau also.
Conflicts:
drivers/gpu/drm/amd/amdkfd/Makefile
drivers/gpu/drm/amd/amdkfd/kfd_chardev.c
drivers/gpu/drm/amd/amdkfd/kfd_mqd_manager.c
drivers/gpu/drm/amd/amdkfd/kfd_priv.h
drivers/gpu/drm/amd/include/kgd_kfd_interface.h
drivers/gpu/drm/i915/intel_runtime_pm.c
drivers/gpu/drm/radeon/radeon_kfd.c
The userspace-requested plane coordinates are now always available via
plane->state.base (and the i915-adjusted values are stored in
plane->state), so we no longer use the coordinate fields in intel_plane
and can drop them.
Also, note that the error case for pageflip calls update_plane() to
program the values from plane->state; it's simpler to just call
intel_plane_restore() which does the same thing.
v2: Replace manual update_plane() with intel_plane_restore() in pageflip
error handler.
Reviewed-by(v1): Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Switch plane handling to use the atomic plane helpers. This means that
rather than provide our own implementations of .update_plane() and
.disable_plane(), we expose the lower-level check/prepare/commit/cleanup
entrypoints and let the DRM core implement update/disable for us using
those entrypoints.
The other main change that falls out of this patch is that our
drm_plane's will now always have a valid plane->state that contains the
relevant plane state (initial state is allocated at plane creation).
The base drm_plane_state pointed to holds the requested source/dest
coordinates, and the subclassed intel_plane_state holds the adjusted
values that our driver actually uses.
v2:
- Renamed file from intel_atomic.c to intel_atomic_plane.c (Daniel)
- Fix a copy/paste comment mistake (Bob)
v3:
- Use prepare/cleanup functions that we've already factored out
- Use newly refactored pre_commit/commit/post_commit to avoid sleeping
during vblank evasion
v4:
- Rebase to latest di-nightly requires adding an 'old_state' parameter
to atomic_update;
v5:
- Must have botched a rebase somewhere and lost some work. Restore
state 'dirty' flag to let begin/end code know which planes to
run the pre_commit/post_commit hooks for. This would have actually
shown up as broken in the next commit rather than this one.
v6:
- Squash kerneldoc patch into this one.
- Previous patches have now already taken care of most of the
infrastructure that used to be in this patch. All we're adding here
now is some thin wrappers.
v7:
- Check return of intel_plane_duplicate_state() for allocation
failures.
v8:
- Drop unused drm_plane_state -> intel_plane_state cast. (Ander)
- Squash in actual transition to plane helpers. Significant
refactoring earlier in the patchset has made the combined
prep+transition much easier to swallow than it was in earlier
iterations. (Ander)
v9:
- s/track_fbs/disabled_planes/ in the atomic crtc flags. The only fb's
we need to update frontbuffer tracking for are those on a plane about
to be disabled (since the atomic helpers never call prepare_fb() when
disabling a plane), so the new name more accurately describes what
we're actually tracking.
Testcase: igt/kms_plane
Testcase: igt/kms_universal_plane
Testcase: igt/kms_cursor_crc
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few of the sprite-related function names in i915 are very similar
(e.g., intel_enable_planes() vs intel_crtc_enable_planes()) and don't
make it clear whether they only operate on sprite planes, or whether
they also apply to all universal plane types. Rename a few functions to
be more consistent with our function naming for primary/cursor planes or
to clarify that they apply specifically to sprite planes:
- s/intel_disable_planes/intel_disable_sprite_planes/
- s/intel_enable_planes/intel_enable_sprite_planes/
Also, drop the sprite-specific intel_destroy_plane() and just use
the type-agnostic intel_plane_destroy() function. The extra 'disable'
call that intel_destroy_plane() did is unnecessary since the plane will
already be disabled due to framebuffer destruction by the point it gets
called.
v2: Earlier consolidation patches have reduced the number of functions
we need to rename here.
v3: Also rename intel_plane_funcs vtable to intel_sprite_plane_funcs
for consistency with primary/cursor. (Ander)
v4: Convert comment for intel_plane_destroy() to kerneldoc now that it
is no longer a static function. (Ander)
Reviewed-by(v1): Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the vblank evasion up from the low-level, hw-specific
update_plane() handlers to the general plane commit operation.
Everything inside commit should now be non-sleeping, so this brings us
closer to how vblank evasion will behave once we move over to atomic.
v2:
- Restore lost intel_crtc->active check on vblank evasion
v3:
- Replace assert_pipe_enabled() in intel_disable_primary_hw_plane()
with an intel_crtc->active test; it turns out assert_pipe_enabled()
grabs some mutexes and can sleep, which we can't do with interrupts
disabled.
v4:
- Equivalent to v2; v3 change is now squashed into an earlier patch
of the series. (Ander).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once we integrate our work into the atomic pipeline, plane commit
operations will need to happen with interrupts disabled, due to vblank
evasion. Our commit functions today include sleepable work, so those
operations need to be split out and run either before or after the
atomic register programming.
The solution here calculates which of those operations will need to be
performed during the 'check' phase and sets flags in an intel_crtc
sub-struct. New intel_begin_crtc_commit() and
intel_finish_crtc_commit() functions are added before and after the
actual register programming; these will eventually be called from the
atomic plane helper's .atomic_begin() and .atomic_end() entrypoints.
v2: Fix broken sprite code split
v3: Make the pre/post commit work crtc-based to match how we eventually
want this to be called from the atomic plane helpers.
v4: Some platforms that haven't had their watermark code reworked were
waiting for vblank, then calling update_sprite_watermarks in their
platform-specific disable code. These also need to be flagged out
of the critical section.
v5: Sprite plane test for primary show/hide should just set the flag to
wait for pending flips, not actually perform the wait. (Ander)
v6:
- Rebase onto latest di-nightly; picks up an important runtime PM fix.
- Handle 'wait_for_flips' flag in intel_begin_crtc_commit(). (Ander)
- Use wait_for_flips flag for primary plane update rather than
performing the wait in the check routine.
- Added kerneldoc to pre_disable/post_enable functions that are no
longer static. (Ander)
- Replace assert_pipe_enabled() in intel_disable_primary_hw_plane()
with an intel_crtc->active test; it turns out assert_pipe_enabled()
grabs some mutexes and can sleep, which we can't do with interrupts
disabled.
v7:
- Check for fb != NULL when deciding whether the sprite plane hides the
primary plane during a sprite update. (PRTS)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In
commit dbea3cea69
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Dec 15 18:59:28 2014 +0200
drm/i915: sanitize RPS resetting during GPU reset
we disable RPS interrupts during GPU resetting, but don't apply the
necessary GEN6 HW workaround. This leads to a HW lockup during a
subsequent "looping batchbuffer" workload. This is triggered by the
testcase that submits exactly this kind of workload after a simulated
GPU reset. I'm not sure how likely the bug would have triggered
otherwise, since we would have applied the workaround anyway shortly
after the GPU reset, when enabling GT powersaving from the deferred
work.
This may also fix unrelated issues, since during driver loading /
suspending we also disable RPS interrupts and so we also had a short
window during the rest of the loading / resuming where a similar
workload could run without the workaround applied.
v2:
- separate the fix to route RPS interrupts to the CPU on GEN9 too
to a separate patch (Daniel)
Bisected-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Testcase: igt/gem_reset_stats/ban-ctx-render
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87429
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Register a component to be used to interface with the snd_hda_intel
driver. This is meant to replace the same interface that is currently
based on module symbol lookup.
v2:
- change roles between the hda and i915 components (Daniel)
- add the implementation to a new file (Jani)
- use better namespacing (Jani)
v3:
- move the implementation to intel_audio.c (Daniel)
- rename display_component to audio_component (Daniel)
- add kerneldoc (Daniel)
v4:
- run forgotten git rm i915_component.c (Jani)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. This is just the begin of a FBC rework.
v2 (Paulo):
- Revert intel_fbc_init() changed parameter.
- Revert set_no_fbc_reason() rename.
- Rebase.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the function intel_output_name() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we extend the commit_plane handlers for each plane type to be able to
handle fb=0, then we can easily implement plane disable via the
update_plane handler. The cursor plane already works this way, and this
is the direction we need to go to integrate with the atomic plane
handler. We can now kill off the type-specific disable functions, as
well as the redundant intel_plane_disable() (not to be confused with
intel_disable_plane()).
Note that prepare_plane_fb() only gets called as part of update_plane
when fb!=NULL (by design, to match the semantics of the atomic plane
helpers); this means that our commit_plane handlers need to handle the
frontbuffer tracking for the disable case, even though they don't handle
it for normal updates.
v2:
- Change BUG_ON to WARN_ON (Ander/Daniel)
v3:
- Drop unnecessary plane->crtc check since a previous patch to plane
update ensures that plane->crtc will always be non-NULL, even for
disable calls that might pass NULL from userspace. (Ander)
- Drop a s/crtc/plane->crtc/ hunk that was unnecessary. (Ander)
v4:
- Fix missing whitespace (Ander)
v5:
- Use state's crtc rather than plane's crtc in
intel_check_primary_plane(). plane->crtc could be NULL, but we've
already fixed up state->crtc to ensure it's non-NULL (even if
userspace passed it as NULL during a disable call). (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our .update_plane() handlers do the same check/prepare/commit/cleanup
steps regardless of plane type. Consolidate them all into a single
function that calls check/commit through a vtable.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All plane update functions need to unpin the old framebuffer when
flipping to a new one. Pull this logic into a separate function to ease
the integration with atomic plane helpers.
v2: Don't wait for vblank if we don't have an old fb to cleanup (Ander)
v3: Really don't wait for vblank if we don't have an old fb to cleanup.
Previous version only handled this for primary planes; we need the
same change on cursors/sprites too! (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 'prepare' step for all types of planes are pretty similar;
consolidate the three 'prepare' functions into a single function. This
paves the way for future integration with the atomic plane handlers.
Note that we pull the 'wait for pending flips' functionality out of the
primary plane's prepare step and place it directly in the 'setplane'
code. When we move to the atomic plane handlers, this code will be in
the 'atomic begin' step.
v2: Update GEM fb tracking for physical cursors also (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the video overlay state on GPU reset. Any pending overlay request
in the ring has been nuked, and the display itself gets reset. So we
pretty much lose all state here. Adjust the software state to match so
that the next "putimage" will restore things to working order.
v2: Ass a locking check into intel_overlay_release_old_vid() (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/0/NULL/ to appease sparse, reported by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the patch from John which removed obj->ring.
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Converted the flip_queued_seqno value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Again get rid of the _irq request unref by simply moving that
into the unpin worker. Doesn't matter when we hang onto the request
for a bit longer, and in the unpin worker we already grab the
dev->struct_mutex anyway.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted the mmio_flip 'seqno' value to be a request structure as part of the
on going seqno to request changes. This includes reference counting the request
being saved away to ensure it can not be retired and freed while the flip code
is still waiting on it.
v2: Used the IRQ friendly request dereference call in the notify handler as that
code is called asynchronously without holding any useful mutex locks.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
[danvet: Drop the _irq variant and use the normal reques unref,
wrapped in dev->struct_mutex per the discussion on the m-l.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function was in use to check if PSR feature got enabled.
However on HSW and BDW we currently force psr exit by disabling
EDP_PSR_ENABLE bit at EDP_PSR_CTL(dev). So this function was actually
returning the active/inactive state that is different from the enable/disable
meaning and had the risk of false negative.
But anyway this check with DRRS was dangerous, since DRRS could try to get enabled
before PSR gets there. So let's just remove it for now.
A proper synchronization mechanism must be implemented later probably
using pipe config.
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we first enable the RPS interrupts then we clear any pending ones.
By this we could lose an interrupt arriving after we unmasked it. This
may not be a problem as the caller should handle such a race, but logic
still calls for the opposite order. Also we can delay enabling the
interrupts until after all the RPS initialization is ready with the
following order:
1. disable left-over RPS (earlier via intel_uncore_sanitize)
2. clear any pending RPS interrupts
3. initialize RPS
4. enable RPS interrupts
This also allows us to do the 2. and 4. step the same way for all
platforms, so let's follow this order to simplifying things.
Also make sure any queued interrupts are also cleared.
v2:
- rebase on the GEN9 patches where we don't support RPS yet, so we
musn't enable RPS interrupts on it (Paulo)
v3:
- avoid enabling RPS interrupts on GEN>9 too (Paulo)
- clarify the RPS init sequence in the log message (Chris)
- add POSTING_READ to gen6_reset_rps_interrupts() (Paulo)
- WARN if any PM_IIR bits are set in gen6_enable_rps_interrupts()
(Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. Just cleaning and reorganizing it.
v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify the implementation to query DPLL attached to a SKL port.
v2: Rebase on top of the run-time PM on DPMS series (Damien)
v3: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for checking things later.
v2:
- fix hsw infoframe enabled check (Ander)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Add the missing PIPE_CONF_CHECK_I(has_infoframe); line to the
hw state cross-checker.]
[danet: Squash in fixup from Jesse to correctly compute has_infoframe
in the hdmi compute_config function.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This simplifies the code quite a bit compared to iterating over all
rings during the ring interrupt.
Also, it allows us to drop the mmio_flip spinlock, since the mmio_flip
struct is only accessed in two places. The first is when the flip is
queued and the other when the mmio writes are done. Since a flip cannot
be queued while there is a pending flip, the two paths shouldn't ever
run in parallel. We might need to revisit that if support for replacing
flips is implemented though.
v2: Don't hold dev->struct_mutext while waiting (Chris)
v3: Make the wait uninterruptable (Chris)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch provides the implementation for reading the pipe wm HW
state.
v2: Incorporated Damien's review comments and also made modifications
to incorporate the plane/cursor split.
v3: No need to ident a line that was fitting 80 chars
Return early instead of indenting the remaining of a function
(Damien)
v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the structures needed for computation of
watermarks of pipes and planes for SKL.
v2: Incorporated Damien's review comments and removed unused fields
in structs for future features like rotation, drrs and scaling.
The skl_wm_values struct is now made more generic across planes
and cursor planes for all pipes.
v3: implemented the plane/cursor split.
v4: Change the wm union back to a structure (Ville, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.
v2: Explain the need for mmio_flip.work in the commit message (Paulo)
Initialize the mmio_flip work in intel_crtc_init() (Paulo)
Prevent new flips the previous flip work finishes (Paulo)
Don't acquire modeset locks for mmio flip work
Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will help future code if this function knows something about of the context
of the display setup object is being pinned for.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function was removed in:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Paulo said when introducing the enum, having more types is really
good to document what should go where (int foo(int, int, bool, bool).
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we suspend we turn everything off so the pps should be idle, and we
also (or at least should) disable all power wells which will reset the
power sequencer port assignment. So when we resume all power sequencers
should be in their reset state. However it's at least theoretically
possible that the BIOS would touch the power seuqencer(s), so to be safe
we ought to read out the current port assignment like we do at driver
init time.
To do that we can simply call vlv_initial_power_sequencer_setup() from
the encoder ->reset() hook before calling intel_edp_panel_vdd_sanitize().
There's no danger or clobbering the pps delays since we now have those
stored within intel_dp and we don't change them once initialized.
This will make sure that the vdd state gets correctly tracked post-resume
in case the BIOS enabled it.
We need to shuffle things around a bit to get the locking right, and
while at it, make intel_edp_panel_vdd_sanitize() static and move it
around a bit to avoid a forward declaration.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
