Patch:
rt2x00: Make rt2x00_queue_entry_for_each more flexible
commit: 10e11568ca
introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.
The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Reported-by: Balint Viragh <bviragh@dension.com>
Tested-by: Balint Viragh <bviragh@dension.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add necessary RF chipset define and basic support for these devices.
Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is based on (but now quite far from) the
original work from Luis and Eliad. Add support
for configuring WoWLAN triggers, and getting
the configuration out again. Changes from the
original patchset are too numerous to list,
but one important change needs highlighting:
the suspend() callback is passed NULL for the
trigger configuration if userspace has not
configured WoWLAN at all.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver only disable multicast filtering when the
FIF_ALLMULTI driver flag has been just set (ie,
if changed_flags& FIF_ALLMULTI and *new_flags& FIF_ALLMULTI) or else
it will reenable multicast filtering.
But next time, this condition will be false and multicast filtering
will be reenabled, even through FIF_ALLMULTI is still set.
This mean that allmulticast only works for less than two minutes in
ad-hoc mode. This patch fixes that to disable multicast filtering
as long as FIF_ALLMULTI is set.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WEP key length was being set to 0 erroneously which broke WEP support.
Fix the same by setting the key length appropriately.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only user of WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS was removed
and consequently, this flag can be removed, too. In addition, a single
capability flag was not enough to indicate this capability clearly since
the device behavior may be different based on which operating mode is
being used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit dbd2fd656f added a mechanism for
user space to indicate whether a default key is being configured for
only unicast or only multicast frames instead of all frames. This
commit added a driver capability flag for indicating whether separate
default keys are supported and validation of the set_key command based
on that capability.
However, this single capability flag is not enough to cover possible
difference based on mode (AP/IBSS/STA) and the way this change was
introduced resulted in a regression with drivers that do not indicate
the new capability (i.e.., more or less any non-mac80211 driver using
cfg80211) when using a recent wpa_supplicant snapshot.
Fix the regression by removing the new check which is not strictly
speaking needed. The new separate default key functionality is needed
only for RSN IBSS which has a separate capability indication.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip initialization of local variables with some default values
if the values are not going to be used further down the code path.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scan and assoc (infra/ibss) commands are simultaneously
given in two terminals, association response is erroneously
served while serving the scan response.
mwifiex_cfg80211_results() is the common routine for sending
ioctl (scan, assoc etc.) results to cfg80211 stack. In above
scenario even if the common routine is called for scan ioctl
context, it also tries to send information about assoc ioctl to
cfg80211 because "priv->assoc_request/priv->ibss_join_request"
flag is on at that time.
Fix the issue by updating request variable after assoc handling
and modifying the variable check in mwifiex_cfg80211_results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify rtlwifi routines for rtl8192se and set up Kconfig
and Makefile for new driver.
This patch also disables ASPM for the RTL8192SE to prevent some strange
crashes on LF's system.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines trx.c and trx.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines table.c and table.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines sw.c and sw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines rf.c and rf.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines reg.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines phy.c and phy.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines led.c and led.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines hw.c and hw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines fw.c and fw.h for RTL8192SE. In addition, make changes
to rtlwifi/wifi.h to support RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines dm.c and dm.h for RTL8192SE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce routine def.h for rtl8192se.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the driver's queue depth reaches the max, the queues are
stopped by the driver till the driver can accept the frames.
At the mean time dynamic_ps_timer can be expired due to not
receiving packet from upper layer which could restart the transmission
at the end of ps work. Due to the mismatch with driver state,
mac80211 is unneccesarity buffering all the frames till the driver
wakes up the queue.
Check whether there is no transmit or the tx queues were stopped by some
reasons. If any of the queue was stopped, the postpond ps timer and
do not restart netif_tx.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping of internal mgmt packets is set to VO. Set the TID
value to match the queue mapping. Otherwise drivers that only look at
the TID might get confused.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at http://marc.info/?l=linux-netdev&m=130428493104730&w=2
libertas frequently generates spurious tx timeouts, because the tx
queue is brought down for extended periods during scanning. The net
layer takes a look and incorrectly assumes the queue has been down for
several seconds, and generates a tx_timeout.
One way to fix this is to bump the trans_start counter while scanning
so that the network layer knows that the device is still alive, but
I think the tx_timeout handler is implemented wrongly here and not of
any real use, so I vote to remove it.
As explained at http://marc.info/?l=linux-wireless&m=130430311115755&w=2
the watchdog is primarily meant to deal with lockup on the hardware TX
path (detected by the tx queue being stopped for an extended period of
time), but this is unlikely to happen with libertas. In this case, the tx
queue is stopped only while waiting for lbs_thread to send the queued frame
to the driver, and lbs_thread wakes up the queue immediately after, even
if the frame could not be sent correctly.
So, the only hardware-related possibility that this catches is if
hw_host_to_card hangs - this is something I have never seen. And if it
were to happen, nothing done by lbs_tx_timeout would actually wake up
lbs_thread any quicker than otherwise.
Removing this oddly-behaving spuriously-firing tx_timeout handler should
fix an occasional kernel crash during resume
(http://dev.laptop.org/ticket/10748)
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
netif_tx_start_all_queues is used to allow the upper layer
to transmit frames but it does not restart transmission.
To restart the trasmission use netif_tx_wake_all_queues.
Not doing so, sometimes stalls the transmission and the
application has to be restarted to proceed further.
This issue was originally found while sending udp traffic
in higer bandwidth in open environment without bgscan.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.
This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_cmd_append_tsf_tlv(), two tsf_val TLVs should be
filled in the buffer and then sent to firmware.
The missing first TLV for tsf_val is added back in this patch.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB drivers don't support automatically waking up when in powersaving mode,
add a work object which will wakeup the device in time to receive the next beacon.
Based on that beacon, we either go back into powersaving mode, or we remain awake
to receive the buffered frames for our station.
Some part of the code, especially rt2x00lib_find_ie and rt2x00lib_rxdone_check_ps
are inspired on the code from carl9170.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use flag instead of re-reading the eeprom every time.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800lib.c the rt2800_init_eeprom function the same eeprom
words were read multiple times, due to inefficient ordering of the
eeprom checks.
Reorder the checks so that each EEPROM word only has to be read once.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch
rt2x00: Optimize register access in rt2800pci
from Helmut Schaa missed one register call, namely
the rt2800_register_multiwrite which should be changed
to rt2x00pci_register_multiwrite.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add recycling functionality to rt2x00usb_register_read_async.
When the callback function returns true, resubmit the urb to
read the register again.
This optimizes the rt2800usb driver when multiple TX status reports
are pending in the register, because now we don't need to allocate
the rt2x00_async_read_data and urb structure each time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no TX status was available, the default timeout
of 20ms is a bit high. The frame is highly likely already
send out, so the TX status should be available within
only a few milliseconds.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 handles MIC failures differently
depending on whenever they are detected by the stack's
own software crypto or when are handed down from the
driver.
This patch tries to unify both by moving the special
branch out of mac80211 rx hotpath and into into the
software crypto part. This has the advantage that we
can run a few more sanity checks on the data and verify
if the key type was TKIP. This is very handy because
several devices generate false postive MIC failure
reports. Like carl9170, ath9k and wl12xx:
<http://www.spinics.net/lists/linux-wireless/msg68494.html>
"mac80211: report MIC failure for truncated packets in AP mode"
Cc: Luciano Coelho <coelho@ti.com>
Cc: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By reading the "driver_state" debugfs value we get all the important
state information from the wl12xx driver. This helps testing and
debugging, particularly in situations where the driver seems "stuck".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP, the TX queues are not stopped when we start
recovery. mac80211 is notified only after the fact. When there is
pending TX, it will be queued even after the FW is down. This leads to
situations where the TX queues are stopped (because of the TX-watermark
mechanism), and are never woken up when we return from recovery.
Fix this by explicitly stopping the TX queues when before initiating
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This entry is useful for debugging the driver state machine during
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When there's a change in the basic rates of the AP, reconfigure relevant
templates with the new rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.
When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.
Unify rate configuration on initialization and on change notification
into a single function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When performing recovery, print the firmware version and program
counter (by reading the SCR_PAD4 register). The value of the firmware
program counter during assert can be useful for debugging.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We use a long timeout (2 seconds) when sending commands to the FW.
When a command times out, it means the FW is stuck, and we should
commence recovery.
This should make recovery times shorter as we'll recover on the first
timeout indication.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New AP-mode FWs filter external beacons by default. Disable this
filtering on start up so we can properly configure ERP protection.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
