Initial commit for PH1-Pro4 Ace board support.
Note:
There are two variants for the amount of DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is used for on-board inter-connection.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This board has an EEPROM (STMicroelectronics M24C64-WMN6TP) connected
to the I2C channel 0 of the SoC. Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During the review process of the UniPhier System Bus driver
(drivers/bus/uniphier.c), the current binding of the System Bus
Controller turned out to be no good. In order to make the driver
really usable, we have to switch over to the new binding defined by
Documentation/devicetree/bindings/bus/uniphier-system-bus.txt.
The old binding will be still supported for a while to keep the
backward compatibility.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This property is used in common by several boards. Move it to the
common place (uniphier-support-card.dtsi). If necessary, each board
can still override the property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to the company's awful projecting, this chip has been renamed to
PH1-LD20. It has not been shipped yet, this change would have no
impact on our customers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New i.MX6 board support: NXP/Freescale imx6qp boards, Advantech/GE,
Uniwest evi, Engicam IMX6 Q7, Toradex Apalis SoM and Ixora carrier
boards
- Relicense vf610 dts files under GPLv2/X11
- A patch series from Stefan updating Vybrid Colibri board support with
PMU, regulators and other devices enabled
- Correct PWM pinmux for Ventana boards and add more pinmux for GW54xx
- Clean up imx6q-tbs2910 dts file and add SATA PHY configuration
- A series from Russell cleaning up hummingboard dts files
- A series from Lothar updating Ka-Ro i.MX28, i.MX53 and i.MX6 boards
to use better audio codec frequency and display configurations
- Clean up whitespaces in i.MX6UL pinctrl header and add more devices
support for the SoC
- Other random dts updates to enable various devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW1aZfAAoJEFBXWFqHsHzOWvwH/1ieekZ5VYnGyO4CT39DaNxU
LMkywkPtp8oUfdVHOfGEMj43knYHsaVFakGS2w8iMNzg+YonWXG/mkR3HUJmoS1L
HzFEnapLzACSSCbn8yZzWzzNvAlg2arqFErQUlhXe9/CNz64uZSigsO3Ib/JNOlX
GWDRa8szryEkEyk2cJo/wyWWSkLGGRai4uNBR6BmUq/MltVjVHOvTV5NeyKpinHZ
mQQFGEbvVk1hJ0sfceX/rmdxgvV0H3Axq8C0JyzbevUTcvS45A85tEXHkrHbYb/f
mJCNXxmmt+NrH8x79YxnuhKTRQ8lNn8fBu9wOtMaBJjRNB3ie3HBh2QabXBs/MA=
=FKmy
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt2
Merge "i.MX device tree updates for 4.6" from Shawn Guo:
- New i.MX6 board support: NXP/Freescale imx6qp boards, Advantech/GE,
Uniwest evi, Engicam IMX6 Q7, Toradex Apalis SoM and Ixora carrier
boards
- Relicense vf610 dts files under GPLv2/X11
- A patch series from Stefan updating Vybrid Colibri board support with
PMU, regulators and other devices enabled
- Correct PWM pinmux for Ventana boards and add more pinmux for GW54xx
- Clean up imx6q-tbs2910 dts file and add SATA PHY configuration
- A series from Russell cleaning up hummingboard dts files
- A series from Lothar updating Ka-Ro i.MX28, i.MX53 and i.MX6 boards
to use better audio codec frequency and display configurations
- Clean up whitespaces in i.MX6UL pinctrl header and add more devices
support for the SoC
- Other random dts updates to enable various devices
* tag 'imx-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (75 commits)
ARM: dts: imx53-qsb: Fix gpio button polarity
ARM: dts: vfxxx: Add DAC node for Vybrid SoC
ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
ARM: dts: imx: Add support for Advantech/GE B850v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE Bx50v3
ARM: dts: imx: Add Advantech BA-16 Qseven module
of: Add vendor prefix for General Electric Company
of: Add vendor prefix for Advantech Corporation
ARM: dts: imx35.dtsi: change the clock information for usb
ARM: dts: imx25.dtsi: change the clock information for usb
ARM: dts: imx6ul: add kpp support
ARM: dts: imx6ul: add gpmi support
ARM: dts: imx6ul: add lcdif support
ARM: dts: imx6ul: add sai support
ARM: dts: imx6ul: add flexcan support
ARM: dts: imx6ul: add sdma support
ARM: dts: imx6ul: add pwm[1-4] nodes
ARM: dts: imx6ul: disable PWMs by default
...
The polarity of the gpio buttons is defined to '0' which is
active high. The buttons are active low though which has been verified by
testing it and by looking into the schematics. While at it use
defines rathers than numbers for the key codes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device tree node entry for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The backlinks are already there since commit 4520e69238 ("ARM: dts:
imx6qdl: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
and were moved by commit 70c2652c6c ("ARM: dts: imx6qdl: Move existing
MIPI DSI ports into a new 'ports' node"), but the links from IPU2 DI0/1
to the MIPI DSI mux are missing. Fix this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds vendor prefix for General Electric Company
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For imx35, it needs three clocks to let the controller work,
the old code is wrong, and the usbmisc does not include
clock handling code any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For imx25, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock
handling code any more.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device node for the i.MX6UL keypad controller.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the device node for the i.MX6UL GPMI interface and the related
APBH DMA which is necessary for the GPMI to work properly.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device nodes for the PWM uinits 1..4 which were missing in the
original commit for i.MX6UL support.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration. This is in sync with a recent change
(commit e2675266b3 "ARM: dts: imx6qdl: disable PWMs by default")
to other i.MX SoCs.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6UL GPT unit requires real clocks. Define the appropriate
clocks to make it work.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul.dtsi references the macro 'KEY_POWER' from
dt-bindings/input/input.h. Thus, move the include statement for this
file from imx6ul-14x14-evk.dts to imx6ul.dtsi itself.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the tsc node to keep the nodes sorted in ascending order by unit
address.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pad DISPB2_SER_RS has no function DISP1_EXT_CLK.
The definition is obviusly a copy/paste error from
MX51_PAD_DISPB2_SER_RS__DISP1_PIN16.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Various pads are missing the input_sel offset and value. Fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Freescale Vybrid SoC include a Cortex-A5 core which supports
ARM's standard PMU (performance monitoring unit). Include the
monitoring unit into the Cortex-A5 base device tree vf500.dtsi.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri standard does not define a pin for SD-Card write-
protection. Use the disable-wp property to indicate that there
is no physical WP line present.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign Ethernet clock parents explicitly. The Colibri VF61
uses the 50MHz Ethernet clock provided by PLL5.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
