Use pointers to properties as device and adapter properties are
constant. No need to embed and copy those structures.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move frontend_attach, tuner_attach, frontend_ctrl and streaming_ctrl
from adapter to device.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware handling routines for various Cypress chips.
Cypress AN2135
Cypress AN2235
Cypress FX2
These were split out from general DVB USB module by
Patrick Boettcher. I did only small changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop remote polling and USB streaming before suspend and resume
those when back to normal operation.
It is far away from complete implementation, but at least it does
not hang system anymore on suspend while streaming is ongoing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In my understanding we never call .disconnect() when .probe()
returns error. Change .probe() to return error all cases it cannot
handle given interface and simplify .disconnect() handling.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better to allow driver finish pending operations and
disconnect device. Killing all ongoing USB transfers could have very
bad effect, even break hardware in worst case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Almost all hacks are now removed and much less code.
Reducing af9015 driver code from 2084 to 1609, it is almost
500 LOC less!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compilation was disabled as it was failing with allyesconfig.
Rename duplicate functions and enable building.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was possible to free resources by unloading module while
initialization was still ongoing on delayed work.
Use PID to make decision on .disconnect() if caller is our
work or some other as work also calls .disconnect() in error
case. There could be better solution still...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Debug prints write operation data instead of read data was
intention.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no USB match flag for used USB interface. It is rather
common there is multiple interfaces offering different services.
For example one for television and one for remote controller.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No worth to keep it on own file as it is only 30 LOC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use Kernel logging insteads of own macros.
Get rid of old debugs and use dynamic debug.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unregister all if there is any error meet during
frontend initialization.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling usb_clear_halt() during device init is not correct.
2 of 7 AF9015 devices I have timeouts next USB control message
after usb_clear_halt(). It was originally performed between
tuner_attach() and rc_query() and likely not causing problems
since rc_query() is repeated continously. None could see it when
first rc_query() failed...
Secondly it was not called for .generic_bulk_ctrl_endpoint_response.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move work to the struct dvb_usb_device that we can access
it inside .disconnect().
Also many other minor changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It could be null in case of driver does not set it
properly, like missing dynamic ID handling.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adapter priv is not really needed, use device priv instead.
There is only driver or two using that.
Device caps are not needed. There was only "has I2C adapter"
capability defined. It is useless as we can see same just
checking existence of i2c_algo callback.
And also remove some totally not used at all variables.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove Cypress USB-interface firmware downloading routines.
That is common module and having single vendor chip routines
in common module is wrong. Just move those elsewhere.
Move single function out from the dvb_usb_firmware.c and
remove that file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delay firmware download and whole driver initialization using
workqueue. udev causes problems when blocking firmware download
was done during module init. This will likely resolve all
DVB USB firmware downloading issues we have had during recent years.
Fixes bug in case of DVB USB driver:
https://bugzilla.redhat.com/show_bug.cgi?id=827538
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed because all frontends are attached as a one go.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of (struct dvb_usb_adapter_fe_properties) as we no longer
need it. Frontends are now defined as a array of pointers inside
adapter struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move .frontend_attach(), .tuner_attach() and .streaming_ctrl()
from the frontend to adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Filtering given PIDs from the transport stream is done by the
DVB USB bridge. It is highly possible there is limitations what
kind of stream DVB USB bridge can PID filter, but it still does
not make sense to define filters for each frontend as frontend
could offer different stream types for different standards.
Likely new way is to enable / disable PID filters are needed to
make decision at runtime (callback). PID filters are quite legacy
stuff as those are aimed cut stream smaller to fit for the USB1.1...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move USB stream properties from frontend to adapter.
It is property of adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new callback in order to resolve used TS (MPEG transport stream)
configuration. Normal TS is 188 byte payload only but there is
currently 204 byte TS and raw TS supported too.
Traditionally TS type was mapped as a frontend property but it
does not work no longer after we changed from MFE (multi-frontend)
to SFE (single-frontend). So it is not possible to map TS for the
given FE as there could be only one FE instead of multiple.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move stream from the frontend to adapter. There could be only
one stream per adapter. One adapter can has multiple frontends
but only one can stream at the time.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New callback to resolve current USB stream configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change URB count, buffer size and type [BULK/ISOC]
dynamically when needed if existing URB buffers are
big enough.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those must be initialized earlier as we now pass
(struct dvb_usb_device *) to the firmware download
callbacks too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most commonly only one firmware is used by the driver
and it is not needed to selected run time. So restore
old functionality but allow .get_firmware_name() callback
to override it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That callback is called only once when device is connected.
Call is done after the possible firmware is downloaded to the device,
just after the .power_ctrl() and before adapters are created.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback to resolve adapter count of current device.
Old static .num_adapters field can be still used but
the new .get_adapter_count() has priority if both
offered by the driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pass all the needed data to the DVB USB core using
(struct usb_device_id) .driver_info. That simplifies
old code a lot and saves memory as all device IDs and
names are not defined inside (struct dvb_usb_device_properties)
as earlier.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use callback to return firmware name instead of static firmware name.
There is some chips that needs to select firmware name according to
chip revision.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
