LAG-related records have specific format in SFN register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG-related records have specific format in SFD register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of SLDR, SLCR2, SLCOR registers that are used to
configure LAG.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion queue element for receive queue provides information if the
packet was received via LAG port. Extract this info and pass it along
to core.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower layer (pci) has information if the packet is received via LAG port.
If that is the case, it fills up rx_info accordingly. However upper
layer does not care about lag_id/port_index for received packets so
convert it to local_port before passing it up. For that conversion, lag
mapping array is introduced. Upper layer is responsible for setting up
the mapping according to what is set in HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add just a stub for now. This allows to pass check in dev_ifsioc,
SIOCADDMULTI and SIOCDELMULTI cases. Teamd is using these to add LACP
slow MAC.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be correct and symmetric to enslave and set inactive flags during release.
That gives LAG offload drivers - lower state change listeners - possibility
to do proper cleanup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev notifier listeners know about link and slave state change.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to state notifications.
We allow caller to indicate if the notification should happen now or later,
depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify
function (similar to bond_slave_state_notify) which is later on called
with rtnl mutex and goes over slaves and executes delayed notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev notifier listeners know about link-up and port-enable state
changes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During options set, there will be needed to hold rtnl_mutex in order to
safely call netdev notifiers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is shared info structure for bonding and team. Serves to pass down
info about link state and port activity to notification listeners.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When lower device like bonding slave, team/bridge port, etc changes its
state, it is useful for others to notice this change. Currently this is
implemented specificly for bonding as NETDEV_BONDING_INFO notifier. This
patch aims to replace this specific usage and make this more generic to
be used for all upper-lower devices.
Introduce NETDEV_CHANGELOWERSTATE netdev notifier type and
netdev_lower_state_changed() helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize netdev_lag_upper_info structure by TX type according to
current bonding mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize netdev_lag_upper_info structure by TX type according to
current team mode and pass it along via netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This struct will be shared by bonding and team to pass internal
information to notifier listeners.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate netdev_master_upper_dev_link_private and pass priv directly as
a parameter of netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code does not mind if a device is bond slave or team port and treats
them the same, as generic LAG ports.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code does not mind if the master is bond or team and treats them
the same, as generic LAG.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other helpers, caller can use this to find out if device is
team port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other helpers, caller can use this to find out if device is
team master.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other speeds, add 100G to bonding 802.3ad code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since CHANGEUPPER can now fail, add support for it in the newly
introduced netdev notifier error injection infrastructure.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev drivers reflect the newly requested topology to hardware when
CHANGEUPPER is received, after software links were already formed.
However, the operation can fail and user will not be notified, as the
return value of the notifier is not checked.
Add this check and rollback software links if necessary.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fd89545f3 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe and ixgbevf only.
Mark cleans up ixgbe_init_phy_ops_x550em, since this was designed to
initialize function pointers only and moves the KR PHY reset to the
ixgbe_setup_internal_phy_t_x550em which was designed to detect which
mode the PHY operates in and set it up. Added the new thermal alarm
type support used with newer X550EM_x devices. Fixed both ixgbe and
ixgbevf to use a private work queue to avoid hangs, which would
possibly occur when creating and destroying many VFS repeatedly.
Updated ixgbe PTP implementation to accommodate X550EM_x devices,
which handle clocking differently. Fixed specification violations
in the datasheet, which was reported by Dan Streetman. Fixed ixgbe
to check for and handle IPv6 extended headers so that Tx checksum
offload can be done, which was reported by Tom Herbert. Fixed ixgbe
link issue for some systems with X540 or X550 by only inhibiting the
turning PHY power off when manageability is present.
Alex Duyck refactors the MAC address configuration code, which in
turns fixes an issue where once 63 entries had been used, you could no
longer add additional filters. Updated ixgbe to use __dev_uc_sync
which also resolved an issue in which you could not remove an FDB
address without having to reset the port. Updated the ixgbe driver
to make use of all the free RAR entries for FDB use if needed.
v2: updated patch 13 to "Alex Duyck Approved" version, in the original
submission, I had grabbed a previous version of the patch and did not
catch it was superseded by a later version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for seeing how to coalesce the error handling
into one location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of inhibiting PHY power control when manageability is
present, only inhibit turning PHY power off when manageability
is present. Consequently, PHY power will always be turned on when
requested. Without this patch, some systems with X540 or X550
devices in some conditions will never get link.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for and handle IPv6 extended headers so that Tx checksum
offload can be done. Also use skb_checksum_help for unexpected
cases. Thanks to Tom Herbert for noticing these problems. Thanks
to Alexander Duyck for recognizing problems with the first version
of this patch and recognizing how to coalesce error conditions
into a single location.
Reported-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the datasheets, the driver should wait for the master
disable bit to read as being set before checking the status
register for master disable.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver was violating the specification in the datasheet
by not waiting 1ms before checking for the reset bit clearing. This
is called out for devices supported by ixgbe, so implement the
required delay.
Reported-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x devices handle clocking differently, so update the
PTP implementation to accommodate them. This involves significant
changes to ixgbe's PTP code to accommodate the new range of
behaviors including things like non-power-of-2 clock wrapping.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we allow the PF to make use of all free RAR
entries for FDB use if needed.
Previously the code limited us to 16 unicast entries, however this was
shared between MACVLAN which wasn't limited and the FDB code which was. So
instead of treating the FDB code as a second class citizen I have updated
it so that it has access to just as many entries as the MACVLAN filters.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the ixgbe_write_uc_addr_list call in ixgbe_set_rx_mode
with a call to __dev_uc_sync instead. This works much better with the MAC
addr list code that was already in place and solves an issue in which you
couldn't remove an FDB address without having to reset the port.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the process of tracking down a memory leak when adding/removing FDB
entries I had to go through the MAC address configuration code for ixgbe.
In the process of doing so I found a number of issues that impacted
readability and performance. This change updates the code in general to
clean it up so it becomes clear what each step is doing. From what I can
tell there a couple of bugs cleaned up in this code.
First is the fact that the MAC addresses were being double counted for the
PF. As a result once entries up to 63 had been used you could no longer
add additional filters.
A simple test case for this:
for i in `seq 0 96`
do
ip link add link ens8 name mv$i type macvlan
ip link set dev mv$i up
done
Test script:
ethregs -s 0:8.0 | grep -e "RAH" | grep 8000....$
When things are working correctly RAL/H registers 1 - 97 will be consumed.
In the failing case it will stop at 63 and prevent any further filters from
being added.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make some minor cleanups, such as simplifying return paths, deleting
unneeded initializations, return values more directly and so forth.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a private workqueue to avoid hangs that were otherwise possible
when performing stress tests, such as creating and destroying many
VFS repeatedly.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newer copper PHY implementation used with newer X550EM_x
devices uses a different thermal alarm type than the earlier
one. Make changes to support both types.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'hv_netvsc-less-headroom'
K. Y. Srinivasan says:
====================
hv_netvsc: Eliminate the additional head room
In an attempt to avoid having to allocate memory on the send path, the netvsc
driver was requesting additional head room so that both rndis header and the
netvsc packet (the state that had to persist) could be placed in the skb.
Since the amount of head room requested was exceeding the default head room
as set in LL_MAX_HEADER, we were forcing a reallocation of skb.
With this patch-set, I have reduced the size of the netvsc packet to less
than 20 bytes and with this reduction we don't need to ask for any additional
headroom. We place the rndis header in the skb head room and we place the
netvsc packet in control buffer area in the skb.
V2: - Addressed review comments:
- Eliminated more fields from netvsc packet structure.
V3: - Fixed a typo in patch: hv_netvsc: Don't ask for additional head room in the skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate vlan_tci from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate status from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate xmit_more from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate completion_func from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate is_data_pkt from struct hv_netvsc_packet.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
