This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains fixes to e1000e.
...
Bruce Allan (1):
e1000e: fix test for PHY being accessible on 82577/8/9 and I217
Tushar Dave (1):
e1000e: Correct link check logic for 82571 serdes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PCI block has reset, the memory enable bit will be reset and
the device will not respond to MMIO access. bnx2_reset_task() currently
will not recover when this happens. Add code to detect this condition
and restore the PCI state. This scenario has been reported by some
users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tg3 devices have management firmware that can export sensor data.
Export temperature sensor reading via hwmon sysfs.
[hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for retreiving temperature sensor data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by refactoring code in tg3_ape_send_event(). The common function will
be used in subsequent patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently skips setting this flag if the VPD contains the
firmware version string. We fix this by separating the probing of NCSI
from the reading of the NCSI version string. The APE_HAS_NCSI flag is
needed to properly read sensor data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jett Kirsher says:
====================
This series contains updates to e1000e and ixgbe.
...
Alexander Duyck (5):
ixgbe: Simplify logic for getting traffic class from user priority
ixgbe: Cleanup unpacking code for DCB
ixgbe: Populate the prio_tc_map in ixgbe_setup_tc
ixgbe: Add function for obtaining FCoE TC based on FCoE user priority
ixgbe: Merge FCoE set_num and cache_ring calls into RSS/DCB config
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_fill_rx_data() pulls 64 byte of data in skb->data
Its too much for TCP (with no options) on IPv4, as total size of headers
is 14 + 40 = 54
This means tcp stack and splice() are suboptimal, since tcp payload
is in part in tcp->data, and in part in skb frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporated review comment from Eric Dumazet. Added description
about different RSS hash types which adapter is capable of.
Will add support for ETHTOOL_GRXFH and ETHTOOL_SRXFX as suggested
by Ben Hutchings in a later patch.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereferenced "mclist" after the kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be ">=" here instead of ">". MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for setting synthetic NIC MAC address from within Linux
guests. Before using this feature, the option "spoofing of MAC address"
should be enabled at the Hyper-V manager / Settings of the synthetic
NIC.
Thanks to Kin Cho <kcho@infoblox.com> for the initial implementation and
tests. And, thanks to Long Li <longli@microsoft.com> for the debugging
works.
Reported-and-tested-by: Kin Cho <kcho@infoblox.com>
Reported-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 4197aa7bb8 implements 64 bit
per ring statistics. But the driver resets the 'total_bytes' and
'total_packets' from RX and TX rings in the RX and TX interrupt
handlers to zero. This results in statistics being lost and user space
reporting RX and TX statistics as zero. This patch addresses the
issue by preventing the resetting of RX and TX ring statistics to
zero.
Signed-off-by: Narendra K <narendra_k@dell.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include <linux/delay.h> in
drivers/net/ethernet/nxp/lpc_eth.c
Signed-off-by: Duan Jiong<djduanjiong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were cases where the prio_tc_map was not populated when we were
calling open. This will result in us incorrectly configuring the traffic
classes when DCB is enabled. In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is meant to be a generic clean-up of the remaining functions for
unpacking data from the DCB structures. The only real changes are:
replaced the variable i with tc for functions that were looping through the
traffic classes, and added a pointer for tc_class instead of path since
that way we only need to pull the pointer once instead of once per loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help simplify the logic for getting traffic classes
from user priorities. To do this I am adding a function named
ixgbe_dcb_get_tc_from_up that will go through the traffic classes in
reverse order in order to determine which traffic class contains a bit for
a given user priority.
Adding a declaration for this new function to the header so that
we have a centralized means for sorting out traffic classes belonging to
features such as FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.
-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup code to make it more clean and readable.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYNCH bit and IV bit of RXCW register are sticky. Before examining these bits,
RXCW should be read twice to filter out one-time false events and have correct
values for these bits. Incorrect values of these bits in link check logic can
cause weird link stability issues if auto-negotiation fails.
CC: stable <stable@vger.kernel.org> [2.6.38+]
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Linville says:
====================
Several drivers see updates: mwifiex, ath9k, iwlwifi, brcmsmac,
wlcore/wl12xx/wl18xx, and a handful of others. The bcma bus got a
lot of attention from Hauke Mehrtens. The cfg80211 component gets
a flurry of patches for multi-channel support, and the mac80211
component gets the first few VHT (11ac) and 60GHz (11ad) patches.
This also includes the removal of the iwmc3200 drivers, since the
hardware never became available to normal people.
Additionally, the NFC subsystem gets a series of updates. According to
Samuel, "Here are the interesting bits:
- A better error management for the HCI stack.
- An LLCP "late" binding implementation for a better NFC SAP usage. SAPs are
now reserved only when there's a client for it.
- Support for Sony RC-S360 (a.k.a. PaSoRi) pn533 based dongle. We can read and
write NFC tags and also establish a p2p link with this dongle now.
- A few LLCP fixes."
Finally, this includes another pull of the fixes from the wireless
tree in order to resolve some merge issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Apple Thunderbolt ethernet device is already listed in the driver,
but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and
allows it to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a7959c1, the USB part of rtlwifi was switched to convert
_usb_read_sync() to using a preallocated buffer rather than one
that has been acquired using kmalloc. Although this routine is named
as though it were synchronous, there seem to be simultaneous users,
and the selection of the index to the data buffer is not multi-user
safe. This situation is addressed by adding a new spinlock. The routine
cannot sleep, thus a mutex is not allowed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused argument hw from call to rtl_tid_to_ac().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac uses info->control.sta while doing ampdu aggregation. This patch
changes the usage of the structure info->control.sta, as it is going to be
removed soon from struct ieee80211_tx_info. This patch is a pre-requisit in
order to add transmission power control (TPC) to the mac80211 subsystem.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware needs to be AWAKE and should maintain association
with the AP to process WoW triggers any time
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add suspend/resume/set_wakeup callbacks to the driver
*suspend
- bail out only if all the conditions for configuring WoW.
is fine, currently multivif case is not handled
- check for associated state.
- map wow triggers from user space data.
- add deauth/disassoc pattern and user defined pattern,
for the later a list is maintained.
- store the interrupt mask before suspend, enabled beacon
miss interrupt for WoW.
- configure WoW in the hardware by calling ath9k_hw_wow_enable.
*resume
- restore the interrupts based on the interrupt mask
stored before suspend.
- call ath9k_hw_wow_wakeup to configure/restore the hardware.
- after wow wakeup clear away WoW events and query the
WoW wakeup reason from the status register
*set_wakeup
- to call 'device_set_wakeup_enable' from cfg80211/mac80211
when wow is configured and as per Rafael/Johannnes the
right way to do so rather in the driver suspend/resume
call back
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to help the developers and users to debug/know
whats happening with WoW
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add a new file wow.c which takes care of the hardware code
for WoW.
*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
- tracking wow event mask (to suppress spurious
wow events)
- properly configure suspend/resume WAR registers
- configure PCIE PM control register
- configure MAC WoW registers and their timeouts
- enabling wow configuration like magic packet,
user patterns based on users configuration
- configuring timeouts for KAL, beacon miss,
aifs, slot time, backoff
- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
- primary task is to find the reason for wakeup
from the wow status register
- configure/restore AR_PCIE_PM_CTRL register
- clear all WoW events
- configure/restore suspend/resume WAR registers
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for AR9002 family of chipsets and for WoW sleep, we reprogram
the SerDes so that the PLL and CHK REQ are both enabled. this
uses more power but in certain cases this is required as otherwise
WoW sleep is unstable and chip may disappear.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently the code supports WoW triggers due to
*magic packet
*user defined patterns
*deauth and disassoc patterns
*disconnect - beacon miss, last beacon received timeout,
no ack for keeep alive frames.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
have seperate wow capability flags for
*basic wow support
*device capable of matching exact user defined pattern
or de-authentication/disassoc pattern
*device such AR9280 requires first four bytes for
all sort of patterns
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*add structures, macros and variables for WoW, so that the driver
can make use of it.
*maintain a list for user enabled patterns and masks
*track pattern slots for the hardware limitation on the
maximum number of patterns that can be stored.
*track interrupts enabled before WoW suspend, so
that can be reconfigured after resume
*have macros to parse user defined wow configurations to
hardware code
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex driver supports 2x2 chips as well. Hence valid mcs values
are 0 to 15. The check for mcs index is corrected in this patch.
For example: if 40MHz is enabled and mcs index is 11, "iw link"
command would show "tx bitrate: 108.0 MBit/s" without this patch.
Now it shows "tx bitrate: 108.0 MBit/s MCS 11 40Mhz" with the patch.
Cc: "3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke only required initialization routines for Lancer.
Remove invocation of unnecessary routines.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query die temperature stat for Lancer to report it correctly
in ethtool.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autonegotiation of pause parameters is possible only on some PHYs.
Ability of autoneg of pause parameters is reported by adapter.
Autoneg of pause parameters cannot be changed from driver.
Fix driver to give error when autoneg mode is toggled by user.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First update the adapter variables with the current speed and
mode before fire the notification. Otherwise, the get_settings()
may provide old values.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the kmem cache API doesn't internally allocate
the name but just points to the name that was passed
in we can't use stack memory for it. Move the name
into the transport struct.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.
To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.
Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
info->control.sta may only be dereferenced during the drv_tx call otherwise
could lead to use-after-free bugs
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This stashes away this feature from standard kernel builds.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO support in this driver was intended to support the iwmc3200
device. This hardware never became available to normal humans.
Leaving this driver imposes unwelcome maintenance costs for no clear
benefit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Data pointer on rt2x00queue_for_each_entry() is never used - remove it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge 3290 and 5390 POWER_BOUND and FREQ_OFFSET_BOUND defines.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix indention and remove unnecessary brackets and compares.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.
Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:
- "stuck" ba sessions and package loss, as the
stale BAR would reset the sequence each time.
- lots of reorder releases.
- ...
Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Reported-by: Mikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: Per-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify mlx4_dev_cap to allow IB support when SR-IOV is active. Modify
mlx4_slave_cap to set the "rdma-supported" bit in its flags area, and
pass that to the guests (this is done in QUERY_FUNC_CAP and its
wrapper).
However, we don't activate IB support quite yet -- we leave the error
return at the start of mlx4_ib_add in the mlx4_ib driver.
In addition, set "protected fmr supported" bit to zero in the
QUERY_FUNC_CAP wrapper.
Finally, in the QUERY_FUNC_CAP wrapper, we needed to add code which
checks for the port type (IB or Ethernet). Previously, this was not
an issue, since only Ethernet ports were supported.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests. These proxy QPs
send their packets to a "tunnel" QP owned by the master. The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.
For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key. These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.
This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.
The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.
In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.
The QPNs for these QPs are arranged as follows:
1. The real SQP numbers (8)
2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)
To support these QPs, two new fields are added to struct mlx4_dev:
base_sqp: this is the QP number of the first of the real SQPs
base_tunnel_sqp: this is the qp number of the first qp in the tunnel
sqp region. (On guests, this is the first tunnel
sqp of the 8 which are assigned to that guest).
In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region. (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)
Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In mlx4_init_icm_table(), free the allocated table if we failed to
allocate memory to its entries.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Spotted four duplicate declarations in icm.h, remove them.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There are really only 3 modes that can control the number of queues. Those
are RSS, DCB, and VMDq/SR-IOV. Currently we have things much more broken
up than they need to be for how we are configuring the rings. In order to
try and straiten some of this out I am going to start merging similar
functionality into single functions. To start with I am merging the Flow
Director ring configuration into the RSS ring configuration since Flow
Director cannot function with DCB or SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mask value for ring features was overloaded for FCoE which can lead to
some confusion. In order to avoid any confusion I am splitting the mask
value and adding an offset value. This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently using indices to indicate the upper limit on a ring
feature. However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to count q_vectors instead of MSI-X
vectors. We were using num_msix_vectors to find the number of q_vectors in
multiple places. This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 6d29b1ef introduces a bug, ntohs is __be16_to_cpu,
not cpu_to_be16.
We always use htons on IP_OFFSET and IP_MF, then compare
with network package.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, Using htons on skb->protocol is wrong.
And fix two code style issues: indentation and remove
unnecessary parentheses.
CC: Tristram Ha <Tristram.Ha@micrel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address
when it gets to the last entry of the tx ring. We were not using
the proper macro to skip the last entry when advancing the tx index.
Reported-by: Zongyun Lai <zlai@vmware.com>
Reviewed-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing case was causing ethtool self test to print garbage
value in extra info section.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the number of outstanding read and write AXI transactions from 1
to 8 for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix intermittent hangs in xgmac_rx_refill. If a ring buffer entry already
had an skb allocated, then xgmac_rx_refill would get stuck in a loop. This
can happen on a rx error when we just leave the skb allocated to the entry.
[ 7884.510000] INFO: rcu_preempt detected stall on CPU 0 (t=727315 jiffies)
[ 7884.510000] [<c0010a59>] (unwind_backtrace+0x1/0x98) from [<c006fd93>] (__rcu_pending+0x11b/0x2c4)
[ 7884.510000] [<c006fd93>] (__rcu_pending+0x11b/0x2c4) from [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8)
[ 7884.510000] [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8) from [<c0036abb>] (update_process_times+0x2b/0x48)
[ 7884.510000] [<c0036abb>] (update_process_times+0x2b/0x48) from [<c004e8fd>] (tick_sched_timer+0x51/0x94)
[ 7884.510000] [<c004e8fd>] (tick_sched_timer+0x51/0x94) from [<c0045527>] (__run_hrtimer+0x4f/0x1e8)
[ 7884.510000] [<c0045527>] (__run_hrtimer+0x4f/0x1e8) from [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4)
[ 7884.510000] [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4) from [<c00101d3>] (twd_handler+0x17/0x24)
[ 7884.510000] [<c00101d3>] (twd_handler+0x17/0x24) from [<c006be39>] (handle_percpu_devid_irq+0x59/0x114)
[ 7884.510000] [<c006be39>] (handle_percpu_devid_irq+0x59/0x114) from [<c0069aab>] (generic_handle_irq+0x17/0x2c)
[ 7884.510000] [<c0069aab>] (generic_handle_irq+0x17/0x2c) from [<c000cc8d>] (handle_IRQ+0x35/0x7c)
[ 7884.510000] [<c000cc8d>] (handle_IRQ+0x35/0x7c) from [<c033b153>] (__irq_svc+0x33/0xb8)
[ 7884.510000] [<c033b153>] (__irq_svc+0x33/0xb8) from [<c0244b06>] (xgmac_rx_refill+0x3a/0x140)
[ 7884.510000] [<c0244b06>] (xgmac_rx_refill+0x3a/0x140) from [<c02458ed>] (xgmac_poll+0x265/0x3bc)
[ 7884.510000] [<c02458ed>] (xgmac_poll+0x265/0x3bc) from [<c029fcbf>] (net_rx_action+0xc3/0x200)
[ 7884.510000] [<c029fcbf>] (net_rx_action+0xc3/0x200) from [<c0030cab>] (__do_softirq+0xa3/0x1bc)
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix net tx watchdog timeout recovery. The descriptor ring was reset,
but the DMA engine was not reset to the beginning of the ring.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init and skb alloc in rx. It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver's skb alloc routine (which is
called in init and during rx). It is already being set to the proper value when
eth_type_trans is called on packet receive, and the skb->dev is not referenced
anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init and skb alloc in rx. It is
already being set to the proper value when eth_type_trans is called on packet
receive, and the skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: linux-driver@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init. It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set before calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set after calling eth_type_trans.
eth_type_trans already sets skb->dev to the proper value, thus making this
unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->dev is being unnecessarily set during ring init. It is already being set
to the proper value when eth_type_trans is called on packet receive, and the
skb->dev is not referenced anywhere else in the code.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
URLs to neterion.com and s2io.com no longer resolve. Remove all references to
these URLs in the driver source and documentation.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment. Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defining a function with no parameters as 'T foo()' is the deprecated
K&R style, and is not strictly equivalent to defining it as 'T foo(void)'.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With IB SR-IOV, each slave has its own separate copy of the port
capabilities flags. For example, the master can run a subnet manager
(which causes the IsSM bit to be set in the master's port
capabilities) without affecting the port capabilities seen by the
slaves (the IsSM bit will be seen as cleared in the slaves).
Also add a static inline mlx4_master_func_num() to enhance readability
of the code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the CONT_* and LNA_* messages from
AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only
meant for debugging purpose. Including them in default rx_msg
series could raise huge amount of MCI interrupts when BT traffic
is going on. And also it increases power consumption when WLAN
is scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code in write_{radio,radio}_reg() should just be run if this is a
pci based device. Add the condition again which was removed in commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts a unintended change mad in commit.
commit 4b006b11ca
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Dec 8 15:06:54 2011 -0800
brcm80211: smac: use bcma functions for register access in phy code
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now brcms_c_chipmatch() is also able to handle non PCI devices and also
does some checking for SoC if they are supported by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These extra offsets are only needed by PCIe devices and not when
running on an SoC.
This partly reverts commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The xmtfifo_sz array contains the queue sizes for the different core
revs. This array missed the sizes for the core rev 17 and 28. This
patch extends the array to also include these sizes and adds a warning
if no queue size is stored in the array for the given core rev.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the
phy code again. This patch reverts parts of the following patch.
commit c2c724977f
Author: Arend van Spriel <arend@broadcom.com>
Date: Wed Jun 29 16:46:35 2011 -0700
staging: brcm80211: remove unsupported chipset code from brcmsmac phy
The BCM4716 is working for me with an other firmware and I am working
on adding support for the other chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts some changes made in this commit:
commit 7234592364
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Feb 14 12:16:45 2011 +0100
staging: brcm80211: removal of inactive d11 code
The bcm4716 has a rev 17 wireless core and this condition is needed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on addin the chip IDs to bcma done in this commit in
my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on adding the IDs to bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removed workarounds are already performed in bcma_pmu_workarounds()
and bcma_core_chipcommon_init()
This patch depends on the completion of the workarounds in bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 00:20:26 2012 +0200
bcma: complete workaround for BCMA43224 and BCM4313
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
si_pmu_spuravoid_pllupdate() is now replaced by
bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports
more chips.
This function is in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 01:31:32 2012 +0200
bcma: add bcma_pmu_spuravoid_pllupdate()
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma also stores a pointer to the chipcommon core in its struct,
brcmsmac should use it and not search for the core by its own.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now "struct si_pub pub" does not have to be the first member in struct
si_info any more, if it is the resulting code after compilation should
be the same.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are not used any more.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4716 is a SoC and does not have a PCI client interface, so this
condition is never true.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking if there is a PCIe core on the bus, better check if
hosttype is PCIe.
In the original submission to staging PCIE() checked, if the bustype is
PCI and the buscore is a PCIe core. Now we assume that all cores bcma
supports are PCIe based, so we just have to check if the bustype is PCI.
The old code bcmsmac currently uses searches for a PCIe core on the bus
and if there is one assumes that this is the buscore, which is wrong.
Some SoCs have a PCIe core operating in host mode and this is not the
bus core. The old code also caused a null pointer in
ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set
because there was no PCIe core on the bus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hardware never became available to normal humans. Leaving this
driver imposes unwelcome maintenance costs for no clear benefit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
We should free "chunk" here before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.
Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
commit 587cc28 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.
This might cause the sched scan request to fail
(with -EINVAL) in many cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.
This can happen if a check for STATE_OFF was forgotten in some routine.
Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.
This implementation is similar to the sending of
commands to the FW.
Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.
[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.
In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.
The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We have some API changes and new features in the new firmwares that
are not compatible with older drivers. Increase the version of the FW
filenames for wl12xx to 5.
Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver configures the firmware template for probe requests during
the scan process. If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.
This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.
[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.
When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).
This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Francois Romieu (4):
r8169: mdio_ops signature change.
r8169: csi_ops signature change.
r8169: ephy, eri and efuse functions signature changes.
r8169: abstract out loop conditions.
Hayes Wang (2):
r8169: add RTL8106E support.
r8169: support RTL8168G
Signed-off-by: David S. Miller <davem@davemloft.net>
commit db83d136d7 (gianfar: Fix missing sock reference when
processing TX time stamps) added a potential sk_wmem_alloc imbalance
If the new skb has a different truesize than old one, we can get a
negative sk_wmem_alloc once new skb is orphaned at TX completion.
Now we no longer early orphan skbs in dev_hard_start_xmit(), this
probably can lead to fatal bugs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jiajun Wu <b06378@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If list_for_each_entry, etc complete a traversal of the list, the iterator
variable ends up pointing to an address at an offset from the list head,
and not a meaningful structure. Thus this value should not be used after
the end of the iterator. There does not seem to be a meaningful value to
provide to netdev_warn. Replace with pr_warn, since pr_err is used
elsewhere.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro spin_event_timeout() was designed for simple polling of hardware
registers with a timeout, so use it when we poll the MIIMIND register.
This allows us to return an error code instead of polling indefinitely.
Note that PHY_INIT_TIMEOUT is a count of loop iterations, so we can't use
it for spin_event_timeout(), which asks for microseconds.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding debugfs support has been broken in the presence of network
namespaces since it has been added. The debugfs support does not handle
multiple bonding devices with the same name in different network
namespaces.
I haven't had any bug reports, and I'm not interested in getting any.
Disable the debugfs support when network namespaces are enabled.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently reported that moving a bonding device between network
namespaces causes warnings from /proc. It turns out after the move we
were trying to add and to remove the /proc/net/bonding entries from the
wrong network namespace.
Move the bonding /proc registration code into the NETDEV_REGISTER and
NETDEV_UNREGISTER events where the proc registration and unregistration
will always happen at the right time.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by implementation in smsc911x.c and smsc9420.c
Tested on ARM/pandaboard running android
Signed-off-by: Emeric Vigier <emeric.vigier@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as the manual of module_pci_driver says that
it can be used when the init and exit functions of
the module does nothing but the pci_register_driver
and pci_unregister_driver.
use it for rdc's r6040 driver, as the init and exit
paths does as above, and also this reduces a little
amount of code.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
l4_rxhash is set on skb when rxhash is obtained from canonical 4-tuple
over transport ports/addresses.
We can set skb->l4_rxhash for all incoming TCP packets on bnx2x for
free, as cqe status contains a hash type information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8111G, the settings of phy and firmware are replaced with
ocp functions. r8168g_mdio_{write / read} redirects the relative
settings to suitable ocp functions. A per-device variable is needed
to evaluate the real address of ocp functions.
rtl_writephy(tp, 0x1f, xxxx) is dedicated to keeping said variable
up-to-date.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Twelve functions can fail silently. Now they have a chance to complain.
Macro and pasting abuse has been kept at a level where tags and
friends should not be hurt.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For the higher mtu sizes requiring the buffer size greater than 8192,
the buffers are sent or received using multiple dma descriptors/ same
descriptor with option of multi buffer handling.
It was observed during tests that the driver was missing on data
packets during the normal ping operations if the data buffers being used
catered to jumbo frame handling.
The memory barrriers are added in between preparation of dma descriptors
in the jumbo frame handling path to ensure all instructions before
enabling the dma are complete.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that during multiple reboots nfs hangs. The status of
receive descriptors shows that all the descriptors were in control of
CPU, and none were assigned to DMA.
Also the DMA status register confirmed that the Rx buffer is
unavailable.
This patch adds the fix for the same by adding the memory barriers to
ascertain that the all instructions before enabling the Rx or Tx DMA are
completed which involves the proper setting of the ownership bit in DMA
descriptors.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.
Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an OOPS in brcmsmac driver, which was introduced
by the 11ad patch 'cfg80211: add 802.11ad (60gHz band) support'.
The value IEEE80211_NUM_BANDS increased, which was used in the
brcms_c_regd_init() function.
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the list of commands CMD_802_11_EEPROM_ACCESS had been
defined twice, unnecessarily, luckily with same value.
Remove one occurence.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables user to set mode of Tx/Rx path using "iw set antenna"
command. For non MIMO chips, the command will be used for selecting
specific antenna or configuring antenna diversity mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as the interface brought up, btcoex timer starts running
eventhough the interface is in idle state and WLAN chip is moved
to full sleep mode. There is no point in running btcoex timer when
the wlan interface is in sleep mode and also it might consumes
more power on WLAN idle unassociated state. So lets stop the
btcoex when wlan is idle state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse WPS IEs from start_ap as well as change_beacon handlers
and set them to FW. Beacon IEs, Probe Response IEs and Assoc
Response IEs are parsed from beacon_data and set to FW with
related masks.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Being a fullmac driver, mwifiex takes care of populating
beacon, probe response, association response WPS IEs to firmware.
And firmware is responsible for constructing these frames.
Advertise this to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for change_beacon handler which is needed
for setting modified management IEs to driver and FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All IE buffers are freshly supplied. In such case, there is no need
to preserve earlier buffers with same management mask and index.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While Head/Tail IEs may contain RSN/WPA IEs which needs to be set
for all mgmt subtypes, beacon_ies, probe_resp_ies, assoc_resp_ies
are for specific mgmt subtypes. Move them to separate function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass cfg80211_beacon_data pointer instead of cfg80211_ap_settings.
While setting management IEs we only need cfg80211_beacon_data of
cfg80211_ap_settings which has Tail IE, Head IE and other IE elements.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.
This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is iwlegacy version of:
commit 342bbf3fee
Author: Johannes Berg <johannes.berg@intel.com>
Date: Sun Mar 4 08:50:46 2012 -0800
iwlwifi: always monitor for stuck queues
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On rt2x00_dmastart() we increase index specified by Q_INDEX and on
rt2x00_dmadone() we increase index specified by Q_INDEX_DONE. So entries
between Q_INDEX_DONE and Q_INDEX are those we currently process in the
hardware. Entries between Q_INDEX and Q_INDEX_DONE are those we can
submit to the hardware.
According to that fix rt2x00usb_kick_queue(), as we need to submit RX
entries that are not processed by the hardware. It worked before only
for empty queue, otherwise was broken.
Note that for TX queues indexes ordering are ok. We need to kick entries
that have filled skb, but was not submitted to the hardware, i.e.
started from Q_INDEX_DONE and have ENTRY_DATA_PENDING bit set.
From practical standpoint this fixes RX queue stall, usually reproducible
in AP mode, like for example reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=828824
Reported-and-tested-by: Franco Miceli <fmiceli@plan.ceibal.edu.uy>
Reported-and-tested-by: Tom Horsley <horsley1953@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c00184f9ab4 "ARM: sa11x0/pxa: convert OS timer registers to IOMEM",
magician_defconfig and a few others fail to build because the OSCR
register is accessed by the drivers/net/irda/pxaficp_ir.c but has turned
into a pointer that needs to be read using readl.
There are other registers in the same driver that eventually should
be converted, and it's unclear whether we would want a better interface
to access the OSCR from a device driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Newer devices use 32 bit for boost register,
set the correct value for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit c0357e975a
bnx2: stop using net_device.{base_addr, irq}.
removed netdev->base_addr so we need to update cnic to get the MMIO
base address from pci_resource_start(). Otherwise, mmap of the uio
device will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a device with limited QMI support. It does not support
normal QMI_WDS commands for connection management. Instead,
sending a QMI_CTL SET_INSTANCE_ID command is required to
enable the network interface:
01 0f 00 00 00 00 00 00 20 00 04 00 01 01 00 00
A number of QMI_DMS and QMI_NAS commands are also supported
for optional device management.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, we should change ETH_P_IP from host endian
to big endian, htons, not ntohs.
CC: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With lockdep enabled we get:
=============================================
[ INFO: possible recursive locking detected ]
3.4.4-Cavium-Octeon+ #313 Not tainted
---------------------------------------------
kworker/u:1/36 is trying to acquire lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813da7e8>] mdio_mux_read+0x38/0xa0
but task is already holding lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813d79e4>] mdiobus_read+0x44/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&bus->mdio_lock);
lock(&bus->mdio_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
.
.
.
This is a false positive, since we are indeed using 'nested' locking,
we need to use mutex_lock_nested().
Now in theory we can stack multiple MDIO multiplexers, but that would
require passing the nesting level (which is difficult to know) to
mutex_lock_nested(). Instead we assume the simple case of a single
level of nesting. Since these are only warning messages, it isn't so
important to solve the general case.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
broadcom, not marvell.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB and SR-IOV cannot currently be enabled at the same time as the queueing
schemes are incompatible. If they are both enabled it will result in Tx
hangs since only the first Tx queue will be able to transmit any traffic.
This simple fix for this is to block us from enabling TCs in ixgbe_setup_tc
if SR-IOV is enabled. This change will be reverted once we can support
SR-IOV and DCB coexistence.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx phys don't support autonegotiation, so don't use it by
default, as otherwise phy_state_machine() will try to enable it (using
c22 requests, which also don't make any sense for the bcm78xx).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable interrupts if it is not our interrupt
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Optima EEE chipset.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OFF carrier state is setup in probe() open() and suspend() functions.
The carrier ON state is managed in macb_handle_link_change().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
some people report atl1c could cause system hang with following
kernel trace info:
---------------------------------------
WARNING: at.../net/sched/sch_generic.c:258 dev_watchdog+0x1db/0x1d0()
...
NETDEV WATCHDOG: eth0 (atl1c): transmit queue 0 timed out
...
---------------------------------------
This is caused by netif_stop_queue calling when cable Link is down.
So remove netif_stop_queue, because link_watch will take it over.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Cloud Ren <cjren@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a1c7fff7e1 (net: netdev_alloc_skb() use build_skb()) broke b44 on
some 64bit machines.
It appears b44 and b43 use __netdev_alloc_skb() instead of alloc_skb()
for their bounce buffers.
There is no need to add an extra NET_SKB_PAD reservation for bounce
buffers :
- In TX path, NET_SKB_PAD is useless
- In RX path in b44, we force a copy of incoming frames if
GFP_DMA allocations were needed.
Reported-and-bisected-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VFs have 0 in their dev->caps.function field. This is a
valid pci id (usually of the PF). Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
I noticed excess calls to skb_copy_expand() or memmove() in asix driver.
This driver needs to push 4 bytes in front of frame (packet_len)
and maybe add 4 bytes after the end (if padlen is 4)
So it should set needed_headroom & needed_tailroom to avoid
copies. But its not enough, because many packets are cloned
before entering asix_tx_fixup() and this driver use skb_cloned()
as a lazy way to check if it can push and put additional bytes in frame.
Avoid skb_copy_expand() expensive call, using following rules :
- We are allowed to push 4 bytes in headroom if skb_header_cloned()
is false (and if we have 4 bytes of headroom)
- We are allowed to put 4 bytes at tail if skb_cloned()
is false (and if we have 4 bytes of tailroom)
TCP packets for example are cloned, but skb_header_release()
was called in tcp stack, allowing us to use headroom for our needs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drop action is implemented by allocating a QP and keeping it in a reset state
such that the HW drops any packets which are steered to that QP. When a drop action
is requested, we attach the relevant flow to that QP.
Sign-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ethtool APIs for attaching L2/L3/L4 based flow steering
rules to the netdevice RX rings. Added set_rxnfc callback and enhanced
the existing get_rxnfc callback.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device managed flow steering API has three promiscuous modes:
1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.
Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other device resources, the resource tracker is needed for supporting
device managed flow steering rules under SRIOV: make sure virtual functions
delete only rules created by them, and clean all rules attached by a crashed VF.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.
This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.
A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.
B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,
The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, for every change in the net device multicast list, the driver
detaches all the addresses from the HW device, and then attaches the
updated list. This behavior is wrong from two aspects: first, it causes
a load of firmware commands and second, there is period of time where
the correct addresses are not attached, which turned into packet loss.
To improve - a copy of the multicast list is saved by the driver. For
every change in the multicast list, the multicast list copy is used
to find the delta between those two lists and add or remove multicast
addresses as needed.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IDs used by the resource tracker are of type u32, so far this was
ok since all the different resources we were tracking could be encoded in 32bit.
As a preparation step for tracking of resources whose IDs need > 32 bits such
as network flow steering rules, who are 64 bit in size, move to use 64 bit
based resource IDs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the data structure used for managing the SRIOV resource tracking
mechanism from radix tree to red-black tree. This is preparation step
for supporting resource IDs which are 64bit long, such as network flow
steering rules. Such IDs can't be used as radix-tree keys on 32bit
architectures and hence the reason for the change.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_drvdata is called twice at the remove path of driver,
call it once.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was useful for debugging the queue stop/wake
issues and is pretty small so let's just put it in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove this dead code, it is unused for device newer than
4965.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'echo 1 > log_event' generates the bogus "MAC is in deep sleep"
or "Timeout waiting for hardware access" log messages when
the interface is down, we should just disallow accessing the
device through debugfs when it is down.
Signed-off-by: Richard A. Griffiths <richardx.a.griffiths@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to check trans for non-null
here as it has already been checked in the
caller. This fixes an smatch warning that we
check after having dereferenced it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the recent change of NUM_BANDS from 2 to 3 hwsim
broke. Fix the code by using the right constant but don't
support bands other than 2.4 and 5 GHz.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.
The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least in the i.MX series, the flexcan contrller divides into ver_3
and ver_10, current driver is for ver_3 controller.
i.MX6 has ver_10 controller, it has more reigsters than ver_3 has.
The rxfgmask (Rx FIFO Global Mask) register is one of the new added.
Its reset value is 0xffffffff, this means ID Filter Table must be
checked when receive a packet, but the driver is designed to accept
everything during the chip start, we need to clear this register to
follow this design.
Use the data entry of the struct of_device_id to point chip specific
info, we can set hardware version for each platform.
Cc: linux-can@vger.kernel.org
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
[mkl: add id_table support]
Tested-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of_property_read_u32() can auto handle endian problems, use this
function can make code clean and simple.
No need to check return value here since the following got value
check will handle this.
Cc: linux-can@vger.kernel.org
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make can_restart static to fix the following sparse warning:
drivers/net/can/dev.c:371:6: warning: symbol 'can_restart' was not
declared. Should it be static?
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make cc770_interrupt static to fix the following sparse warning:
drivers/net/can/cc770/cc770.c:699:13: warning: symbol
'cc770_interrupt' was not declared. Should it be static?
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).
An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.
In the end, this patch also adds the EEE ethtool support implementing:
o phy_ethtool_set_eee
o phy_ethtool_get_eee
v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
values according to ethtool API (thanks to Ben's feedback).
Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
Fixed the phy_init_eee function: we need to check which link mode
was autonegotiated and then the corresponding bits in 7.60 and 7.61
registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Energy Efficient Ethernet support to the stmmac.
Please see the driver's documentation for further details about this support
in the driver.
Thanks also goes to Rayagond Kokatanur for his first implementation.
Note:
to clearly manage and expose the lpi interrupt status and eee ethtool
stats I've had to do some modifications to the driver's design and I
found really useful to move other parts of the code (e.g. mmc irq stat)
in the main directly. So this means that some core has been reworked
to introduce the EEE.
v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
o Totally reviewed the ethtool support for EEE
o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
(it has to return -EOPNOTSUPP in that case).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the obsolete strict_strtoul with kstrtoint.
v2: also removed casting on kstrtoul.
v3: use kstrtoint instead of kstrtoul due to all vars are integer.
thanks to E. Dumazet.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Linville says:
====================
Here is another batch of updates intended for 3.6. This includes a
number of pulls, including ones from the mac80211, iwlwifi, ath6kl, and
wl12xx trees. I also pulled from the wireless tree to avoid potential
build conflicts. There are a number of other patches applied directly,
including a number for the Broadcom drivers and the mwifiex driver.
The updates cover the usual variety of new hardware support and feature
enhancements. It's all good work, but there aren't any big headliners.
This does resolve a net-next/wireless-next merge conflict reported
by Stephen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1f85d58cdf
cnic: Remove uio mem[0].
introduced a regression as older versions of userspace app still rely
on this mmap. Restore the mmap functionality and get the base address
from pci_resource_start() as the nedev->base_addr has been deprecated for
PCI devices.
Update version to 2.5.12.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug messages should be printed using dev_dbg() not
dev_err() which requires DEBUG to be defined.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some messages were missing a trailing newline, add it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled.
o update driver version to 4.0.80
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After SKB is queued into tx_queue, it will be freed if request_gop is NULL.
However, no dequeue action is called in this situation, it is likely that
tx_queue constains freed SKB. This patch should fix this issue, and it is
based on 3.5.0-rc4+.
This issue is found through code inspection, no bug is seen with it currently.
I run netperf test for several hours, and no network regression was found.
Signed-off-by: Annie Li <annie.li@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the failing merge in net-next by reverting the last
net-next merge for caif_hsi.c and then merge in the commit:
"caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost"
from the net repository.
The commit:"caif-hsi: Add missing return in error path" from
net repository was dropped, as it changed code previously removed in the
net-next repository.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NLMSG_GOODSIZE results in multiple pages being used as
nlmsg_new() will automatically add the size of the netlink
header to the payload thus exceeding the page limit.
NLMSG_DEFAULT_SIZE takes this into account.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a number of warnings such as:
CC drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Linville says:
====================
Amitkumar Karwar gives us two mwifiex fixes: one fixes some skb
manipulations when handling some event messages; and another that
does some similar fixing on an error path.
Avinash Patil gives us a fix for for a memory leak in mwifiex.
Dan Rosenberg offers an NFC NCI fix to enforce some message length
limits to prevent buffer overflows.
Eliad Peller provides a mac80211 fix to prevent some frames from
being built with an invalid BSSID.
Eric Dumazet sends an NFC fix to prevent a BUG caused by a NULL
pointer dereference.
Felix Fietkau has an ath9k fix for a regression causing
LEAP-authenticated connection failures.
Johannes Berg provides an iwlwifi fix that eliminates some log SPAM
after an authentication/association timeout. He also provides a
mac80211 fix to prevent incorrectly addressing certain action frames
(and in so doing, to comply with the 802.11 specs).
Larry Finger provides a few USB IDs for the rtl8192cu driver --
should be harmless.
Panayiotis Karabassis provices a one-liner to fix kernel bug 42903
(a system freeze).
Randy Dunlap provides a one-line Kconfig change to prevent build
failures with some configurations.
Stone Piao provides an mwifiex sequence numbering fix and a fix
to prevent mwifiex from attempting to include eapol frames in an
aggregation frame.
Finally, Tom Hughes provides an ath9k fix for a NULL pointer
dereference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we don't provide custom regulatory rules to cfg80211,
"chan->max_power" remains uninitialized (0dbm) and
"chan->max_reg_power" will contain maximum power for a channel
extracted from regulatory rules provided by CRDA; hence use
"chan->max_reg_power" in reg_notifier handler instead of
"chan->max_power" to set max_power in firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
