Return -ENOTSUPP if the initialization fails because the
device is configured for a mode that is not supported by the driver.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.
bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.
If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usbnet API use the device ID table to store a pointer to
a minidriver. Setting a generic pointer for dynamic device
IDs will in most cases make them work as expected. usbnet
will otherwise treat the dynamic IDs as blacklisted. That is
rarely useful.
There is no standard class describing devices supported by
this driver, and most vendors don't even provide enough
information to allow vendor specific wildcard matching. The
result is that most of the supported devices must be
explicitly listed in the device table. Allowing dynamic IDs
to work both simplifies testing and verification of new
devices, and provides a way for end users to use a device
before the ID is added to the driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer FW has added new capability checks for VFs.
Driver should only use those capabilities which are allowed for VFs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerr Kirsher says:
====================
This series contains updates to ixgbe & ixgbevf.
...
Alexander Duyck (6):
ixgbe: Ping the VFs on link status change to trigger link change
ixgbe: Handle failures in the ixgbe_setup_rx/tx_resources calls
ixgbe: Move configuration of set_real_num_rx/tx_queues into open
ixgbe: Update the logic for ixgbe_cache_ring_dcb and DCB RSS
configuration
ixgbe: Cleanup logic for MRQC and MTQC configuration
ixgbevf: Update descriptor macros to accept pointers and drop _ADV
suffix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Francois Romieu says:
====================
Francois Romieu (1):
r8169: verbose error message.
Hayes Wang (1):
r8169: remove rtl_ocpdr_cond.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Fix potential badness when running a self-test with SR-IOV enabled.
2. Fix calculation of some interface statistics that could run backward.
3. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug. Increase it to 1500ms.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
handle errors of nla_put() inside the if(nla_put...) {}
This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
bip calibration is not required in wl18xx. Therefore we
disable also auto fem (using calibrator fem detect) mode.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.
this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.
This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.
Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: Yossi Wortzel <yossiw@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).
drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to make the code much more readable for MTQC and MRQC
configuration.
The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
DCB
En Dis
VMDq En VMDQ/DCB VMDq/RSS
Dis DCB/RSS RSS
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.
In this patch I basically did 3 things. I updated the logic for getting
the first register index. I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register. Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues. By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls. Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go. This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.
This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Francois Romieu <romieu@fr.zoreil.com>
b43 with open firmware crashes mac80211 because
it changes the number of queues at runtime which,
while it was never really supported, now crashes
mac80211 due to the new hardware queue logic.
Fix this by detecting open vs. proprietary fw
earlier and registering with mac80211 with the
right number of queues.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org (depends on commit a6f38ac3)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using work_pending() to defer certain operations when
a HW-reset work has been queued is racy since the check
would return false when the work item is actually in
execution. Use SC_OP_HW_RESET instead to fix this race.
Also, unify the reset debug statistics maintenance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface in AP or P2P-GO mode is removed,
check whether a station interface is already present and
reconfigure the beacon timers etc. properly if it's
associated.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, there are problems with how ANI is handled in
multi-VIF scenarios. This patch addresses them by unifying
the start/stop logic.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused variables, use a helper function to choose
the slot and reset beaconing status at one place.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the beacon queue parameters after disabling
interrupts. Also, remove the redundant call in conf_tx()
for IBSS mode since the queue would be configured
with the appropriate cwmin/cwmax values when beaconing
is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the tx_last_beacon() callback, mac80211's beaconing
status can be used instead. The beacon tasklet doesn't require
it because it is disabled when removing a slot.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* The beaconing status routine is not required, since in
multi-VIF cases the HW beacon parameters should not be
re-configured.
* Remove SC_OP_TSF_RESET - when a beaconing interface comes
up the first time, the TSF has to be reset.
* Simplify ath9k_allow_beacon_config().
* Handle setting/clearing the SWBA interrupt properly.
* Remove the TSF mangling in IBSS mode, it is not required.
* General code cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup the messy logic dealing with station association
and disassociation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do not set/clear TSF when adding/deleting an interface.
This should be done when the BSS is set up and should also
take into account the existence of other interfaces.
* Set opmode explicitly.
* ANI setup needs to be decided based on multiple interfaces.
This can be done via the bss_info_changed() callback.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps interface addition and deletion and simplifies
slot allocation. There is no need to setup the beacon buffer
in add/remove interface, remove this and use simple APIs for
assigning/deleting slots.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We found a deadlock in the handling of command failures/reset conditions.
For example:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is queued (but not yet sent to the hardware)
4. The device reset kicks in, causing the if_usb disconnect handler to
set the "surprise removed" flag to be set as the device disappears
from the bus. This causes lbs_thread to stop processing things
("adapter removed; waiting to die"), not processing any further
commands, leaving the second queued command "in the air", causing a
deadlock.
Fix this by removing the surpriseremoved flag setting in if_usb. I can't
see any reason why this needs to be done so early. lbs_remove_card will set
this flag at an appropriate time - i.e. after all pending commands have
been completed or cancelled, avoiding this deadlock.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fail commands immediately when the request cannot be sent to the hardware.
This solves the following deadlock:
1. Two commands are in the queue.
2. The first command is sent, but causes a timeout, which kicks off an
asynchronous device reset
3. The second command is submitted to the device, and fails. The failure
is noted but the existing code waits for the timeout handler to take
care of the failure.
4. The device reset kicks in, causing the device "surprise removed" flag
to be set as the device disappears from the bus.
5. lbs_thread notes this and enters "adapter removed; waiting to die"
mode, without processing any further command timeouts.
While adjusting lbs thread logic to handle this situation may be one way
to fix this, it seems more practical to simplify handling of host_to_card
failure so that the commands are failed immediately without waiting for
more compliated timeout logic to kick in.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reg_notifier can be called before the interface is up.
Handle this correctly by storing the requested country code, then
apply the relevant configuration when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485, AR9330 and AR9340 are the chips that this is *NOT* supposed to be
applied on.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add an inline function for getting the correct modal EEPROM struct
- remove unnecessary indirection through ath9k_hw_ar9300_get_eeprom
access the relevant fields directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the aggregate size exceeds the TXOP limit, it leads to lots of unnecessary
hardware and software retries.
The previous 4ms frame limit table was completely undocumented, the commit
that updated it only vaguely referenced and equation from the standard,
but I've been unable to replicate its results.
Fix this by using a formula based on the code in ath_pkt_duration, which is
more likely to be correct for this case.
Reported-by: Dave Täht <dave.taht@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for using different queue size defaults for each AC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In all those years apparently nobody noticed that the txop limit programmed
into the chip was off by a factor of 32 (!), probably because the VI and VO
queues aren't used that much aside from mgmt frames on VO.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The row/column sizes can be derived from the array argument within the macro
itself, which is less error prone. In a few cases the supplied column size
was actually wrong.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the EEPROM information to choose the right tx gain table
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many chips are not able to deal with non-consecutive rx antenna selections
and respond with calibration errors, reset errors, etc.
When an antenna is selected as a tx antenna, also flag it for rx to avoid
chip issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures data rates to firmware using bitrate mask
provided by cfg80211.
Earlier we used to only update band information in this handler
which will be used later for ibss network. Due to recent
modifications in ibss join code we don't need to do that.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_set_rf_channel() ibss specific flags were unnecessarily
getting modified for infra and AP mode. This patch removes
mwifiex_set_rf_channel() function and adds equivalant code in infra,
ibss and AP path.
For ibss, now we are chosing band based on channel type and basic
rates provided in ibss join request. We can start ibss network in
A only, B only, G only, BG, BGN, AN mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Recently we removed set_channel cfg80211 handler. Also, cfg80211
blocks ibss connection requests if ibss network is already started
/joined. Hence the code to restart ibss network in new channel
(mwifiex_drv_change_adhoc_chan() function) becomes redundant.
2) mwifiex_bss_set_channel() function is redundant. It does some
error checking and calculate adhoc start band and adhoc channel.
Cfg80211 already takes care of error checking and provides correct
channel information to the driver. Adhoc start band is already
calculated in mwifiex_set_rf_channel() function.
Other associated code is also removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code was an accidental copy&paste of the 2.4 GHz version,
which doesn't work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit d83579e2a5 incorporated some
changes from the vendor driver that made it newly important that the
calculated hardware version correctly include the CHIP_92D bit, as all
of the IS_92D_* macros were changed to depend on it. However, this bit
was being unset for dual-mac, dual-phy devices. The vendor driver
behavior was modified to not do this, but unfortunately this change was
not picked up along with the others. This caused scanning in the 2.4GHz
band to be broken, and possibly other bugs as well.
This patch brings the version calculation logic in parity with the
vendor driver in this regard, and in doing so fixes the regression.
However, the version calculation code in general continues to be largely
incoherent and messy, and needs to be cleaned up.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Cc: Stable <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 rate_index changed to be a u8, so
can't hold the negative error value properly.
Use a temporary variable for error checking.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out every most standard Linux distributions enable
CONFIG_EXPERT, so use the shiny new CFG80211_CERTIFICATION_ONUS
which is meant by design to not be enabled by all Linux
distributions.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's done in very similar way this is done in bonding and bridge.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow). Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Fix CID 113952 in Coverity report on Linux.
This is the one instance where we don't, and shouldn't, check the
return code from efx_mcdi_rpc(). It wasn't immediately obvious to me
why we didn't, so I think an explanation is in order.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Fix CID 102619 in the Coverity report on Linux.
efx_end_loopback() iterates over an array of skb pointers of which
some may be null (if efx_begin_loopback() failed). It should not use
dev_kfree_skb_irq(), which requires non-null pointers. In practice
this is safe because it does not run in interrupt context and
therefore always ends up calling dev_kfree_skb(), which does allow
null pointers. But we should make that explicit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Fix CID 113703 in the Coverity report on Linux.
ethtool stats names are limited to 32 bytes including a null
terminator. Use strlcpy() to ensure that we will always include the
null terminator even if a source string becomes longer than this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
With some gcc versions & optimisations, the compiler will warn that
'depth' in efx_filter_insert_filter() may be used without being
initialised, although this is not the case.
This is related to inlining of efx_filter_search(), which only has
one caller since commit 8db182f4a8
('sfc: Remove now-unused filter function').
Shut the compiler up by initialising it to 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The interrupt registers accessed in ixgbevf are more similar to the igb
style registers than they are to the ixgbe style registers. As such we
would be better off setting up the code for the EICS, EIMS, EICS, EIAM, and
EIAC like we do in igb instead of ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF driver is processing all of the transmits in interrupt
context. This can be messy since the Rx is all handled in NAPI and this
may result in interrupts being disabled. In order to resolve this move all
of the Tx packet processing into NAPI and combine all of the interrupt and
polling routines into just a pair of functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For most cases the ixgbevf driver will only ever contain a single Tx and
single Rx queue. In order to track that it makes more sense to use a
pointer instead of using a bitmap which must be search in order to locate
the ring on an adapter index. As such I am changing the code to use
pointers and an iterator to access all rings on a given q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses a kernel panic seen when setting up the interface.
Specifically we see a NULL pointer dereference on the Tx descriptor cleanup
path when enabling interrupts. This change corrects that so it cannot
occur.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up the accounting needed at the start of xmit_frame so
that we can avoid doing too much work to determine how many descriptors we
will need.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch drops the use of eitr_low and eitr_high as values being stored
in the adapter structure. Since the values have no external way to be
changed they might as well just be hard coded values and save us the space
on the adapter structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The IXGBE_FLAG_RX_CSUM_ENABLED flag is redundant since NETIF_F_RXCSUM is
keeping the value we want to already have. As such we can drop the
redundant flag and just make use of NETIF_F_RXCSUM.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no need to keep a separate netdev_registered value since that is
already stored in the netdev itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a large amount of code present in this driver to support features
that either do no exist or are not supported such ask packet split, DCA, or
RSC. This patch strips out almost all of that code and in the case of
conditionals based on unused flags I am flatting the code out to just the
path that would have been selected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
info->control.sta and control.vif may only be dereferenced
during the drv_tx call otherwise could lead to use-after-free
bugs.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marc Kleine-Budde says:
====================
the fifth pull request for upcoming v3.6 net-next. The first two
patches (created by me) add const qualifiers to the flexcan and
mpc5xxx_can driver. The next patch by Julia Lawall fixes a return value
problem in the error path of the softing driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the numbers used for stop/resume queue in a single place and
fix the condition for sanity check.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically, the return value desired for the failure of a function with an
integer return value is a negative integer. In these cases, the return
value is sometimes a negative integer and sometimes 0, due to a subsequent
initialization of the return variable within the loop.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
//<smpl>
@r exists@
identifier ret;
position p;
constant C;
expression e1,e3,e4;
statement S;
@@
ret = -C
... when != ret = e3
when any
if@p (...) S
... when any
if (\(ret != 0\|ret < 0\|ret > 0\) || ...) { ... return ...; }
... when != ret = e3
when any
*if@p (...)
{
... when != ret = e4
return ret;
}
//</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Asix AX88172A is a USB 2.0 Ethernet interface that supports both an
internal PHY as well as an external PHY (connected via MII).
This patch adds a driver for the AX88172A and provides support for
both modes and the phylib.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the new driver for the AX88172A to share code with the
existing drivers for ASIX devices.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch further creates two additional copies of asix.c.
In another patch these copies will be used to factor out
common code.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains fixes to e1000e.
...
Bruce Allan (1):
e1000e: fix test for PHY being accessible on 82577/8/9 and I217
Tushar Dave (1):
e1000e: Correct link check logic for 82571 serdes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PCI block has reset, the memory enable bit will be reset and
the device will not respond to MMIO access. bnx2_reset_task() currently
will not recover when this happens. Add code to detect this condition
and restore the PCI state. This scenario has been reported by some
users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tg3 devices have management firmware that can export sensor data.
Export temperature sensor reading via hwmon sysfs.
[hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for retreiving temperature sensor data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by refactoring code in tg3_ape_send_event(). The common function will
be used in subsequent patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently skips setting this flag if the VPD contains the
firmware version string. We fix this by separating the probing of NCSI
from the reading of the NCSI version string. The APE_HAS_NCSI flag is
needed to properly read sensor data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jett Kirsher says:
====================
This series contains updates to e1000e and ixgbe.
...
Alexander Duyck (5):
ixgbe: Simplify logic for getting traffic class from user priority
ixgbe: Cleanup unpacking code for DCB
ixgbe: Populate the prio_tc_map in ixgbe_setup_tc
ixgbe: Add function for obtaining FCoE TC based on FCoE user priority
ixgbe: Merge FCoE set_num and cache_ring calls into RSS/DCB config
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_fill_rx_data() pulls 64 byte of data in skb->data
Its too much for TCP (with no options) on IPv4, as total size of headers
is 14 + 40 = 54
This means tcp stack and splice() are suboptimal, since tcp payload
is in part in tcp->data, and in part in skb frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporated review comment from Eric Dumazet. Added description
about different RSS hash types which adapter is capable of.
Will add support for ETHTOOL_GRXFH and ETHTOOL_SRXFX as suggested
by Ben Hutchings in a later patch.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereferenced "mclist" after the kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be ">=" here instead of ">". MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for setting synthetic NIC MAC address from within Linux
guests. Before using this feature, the option "spoofing of MAC address"
should be enabled at the Hyper-V manager / Settings of the synthetic
NIC.
Thanks to Kin Cho <kcho@infoblox.com> for the initial implementation and
tests. And, thanks to Long Li <longli@microsoft.com> for the debugging
works.
Reported-and-tested-by: Kin Cho <kcho@infoblox.com>
Reported-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 4197aa7bb8 implements 64 bit
per ring statistics. But the driver resets the 'total_bytes' and
'total_packets' from RX and TX rings in the RX and TX interrupt
handlers to zero. This results in statistics being lost and user space
reporting RX and TX statistics as zero. This patch addresses the
issue by preventing the resetting of RX and TX ring statistics to
zero.
Signed-off-by: Narendra K <narendra_k@dell.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include <linux/delay.h> in
drivers/net/ethernet/nxp/lpc_eth.c
Signed-off-by: Duan Jiong<djduanjiong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were cases where the prio_tc_map was not populated when we were
calling open. This will result in us incorrectly configuring the traffic
classes when DCB is enabled. In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is meant to be a generic clean-up of the remaining functions for
unpacking data from the DCB structures. The only real changes are:
replaced the variable i with tc for functions that were looping through the
traffic classes, and added a pointer for tc_class instead of path since
that way we only need to pull the pointer once instead of once per loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help simplify the logic for getting traffic classes
from user priorities. To do this I am adding a function named
ixgbe_dcb_get_tc_from_up that will go through the traffic classes in
reverse order in order to determine which traffic class contains a bit for
a given user priority.
Adding a declaration for this new function to the header so that
we have a centralized means for sorting out traffic classes belonging to
features such as FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.
-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup code to make it more clean and readable.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally, the PHY can be initially inaccessible when the first read of
a PHY register, e.g. PHY_ID1, happens (signified by the returned value
0xFFFF) but subsequent accesses of the PHY work as expected. Add a retry
counter similar to how it is done in the generic e1000_get_phy_id().
Also, when the PHY is completely inaccessible (i.e. when subsequent reads
of the PHY_IDx registers returns all F's) and the MDIO access mode must be
set to slow before attempting to read the PHY ID again, the functions that
do these latter two actions expect the SW/FW/HW semaphore is not already
set so the semaphore must be released before and re-acquired after calling
them otherwise there is an unnecessarily inordinate amount of delay during
device initialization.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
SYNCH bit and IV bit of RXCW register are sticky. Before examining these bits,
RXCW should be read twice to filter out one-time false events and have correct
values for these bits. Incorrect values of these bits in link check logic can
cause weird link stability issues if auto-negotiation fails.
CC: stable <stable@vger.kernel.org> [2.6.38+]
Reported-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Linville says:
====================
Several drivers see updates: mwifiex, ath9k, iwlwifi, brcmsmac,
wlcore/wl12xx/wl18xx, and a handful of others. The bcma bus got a
lot of attention from Hauke Mehrtens. The cfg80211 component gets
a flurry of patches for multi-channel support, and the mac80211
component gets the first few VHT (11ac) and 60GHz (11ad) patches.
This also includes the removal of the iwmc3200 drivers, since the
hardware never became available to normal people.
Additionally, the NFC subsystem gets a series of updates. According to
Samuel, "Here are the interesting bits:
- A better error management for the HCI stack.
- An LLCP "late" binding implementation for a better NFC SAP usage. SAPs are
now reserved only when there's a client for it.
- Support for Sony RC-S360 (a.k.a. PaSoRi) pn533 based dongle. We can read and
write NFC tags and also establish a p2p link with this dongle now.
- A few LLCP fixes."
Finally, this includes another pull of the fixes from the wireless
tree in order to resolve some merge issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Apple Thunderbolt ethernet device is already listed in the driver,
but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and
allows it to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a7959c1, the USB part of rtlwifi was switched to convert
_usb_read_sync() to using a preallocated buffer rather than one
that has been acquired using kmalloc. Although this routine is named
as though it were synchronous, there seem to be simultaneous users,
and the selection of the index to the data buffer is not multi-user
safe. This situation is addressed by adding a new spinlock. The routine
cannot sleep, thus a mutex is not allowed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused argument hw from call to rtl_tid_to_ac().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac uses info->control.sta while doing ampdu aggregation. This patch
changes the usage of the structure info->control.sta, as it is going to be
removed soon from struct ieee80211_tx_info. This patch is a pre-requisit in
order to add transmission power control (TPC) to the mac80211 subsystem.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware needs to be AWAKE and should maintain association
with the AP to process WoW triggers any time
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add suspend/resume/set_wakeup callbacks to the driver
*suspend
- bail out only if all the conditions for configuring WoW.
is fine, currently multivif case is not handled
- check for associated state.
- map wow triggers from user space data.
- add deauth/disassoc pattern and user defined pattern,
for the later a list is maintained.
- store the interrupt mask before suspend, enabled beacon
miss interrupt for WoW.
- configure WoW in the hardware by calling ath9k_hw_wow_enable.
*resume
- restore the interrupts based on the interrupt mask
stored before suspend.
- call ath9k_hw_wow_wakeup to configure/restore the hardware.
- after wow wakeup clear away WoW events and query the
WoW wakeup reason from the status register
*set_wakeup
- to call 'device_set_wakeup_enable' from cfg80211/mac80211
when wow is configured and as per Rafael/Johannnes the
right way to do so rather in the driver suspend/resume
call back
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
to help the developers and users to debug/know
whats happening with WoW
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add a new file wow.c which takes care of the hardware code
for WoW.
*program the descriptors and data words to periodically
send Keep Alive Frames.
*program the user defined patterns/masks and pattern length
in the hardware registers.
*'ath9k_hw_wow_enable' is called during the drivers suspend
callback which takes care of the following
- tracking wow event mask (to suppress spurious
wow events)
- properly configure suspend/resume WAR registers
- configure PCIE PM control register
- configure MAC WoW registers and their timeouts
- enabling wow configuration like magic packet,
user patterns based on users configuration
- configuring timeouts for KAL, beacon miss,
aifs, slot time, backoff
- create Keep Alive Pattern ('KAL')
*'ath9k_hw_wow_wakeup' is called during the drivers resume
callback which takes care of the following
- primary task is to find the reason for wakeup
from the wow status register
- configure/restore AR_PCIE_PM_CTRL register
- clear all WoW events
- configure/restore suspend/resume WAR registers
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for AR9002 family of chipsets and for WoW sleep, we reprogram
the SerDes so that the PLL and CHK REQ are both enabled. this
uses more power but in certain cases this is required as otherwise
WoW sleep is unstable and chip may disappear.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently the code supports WoW triggers due to
*magic packet
*user defined patterns
*deauth and disassoc patterns
*disconnect - beacon miss, last beacon received timeout,
no ack for keeep alive frames.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
have seperate wow capability flags for
*basic wow support
*device capable of matching exact user defined pattern
or de-authentication/disassoc pattern
*device such AR9280 requires first four bytes for
all sort of patterns
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*add structures, macros and variables for WoW, so that the driver
can make use of it.
*maintain a list for user enabled patterns and masks
*track pattern slots for the hardware limitation on the
maximum number of patterns that can be stored.
*track interrupts enabled before WoW suspend, so
that can be reconfigured after resume
*have macros to parse user defined wow configurations to
hardware code
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex driver supports 2x2 chips as well. Hence valid mcs values
are 0 to 15. The check for mcs index is corrected in this patch.
For example: if 40MHz is enabled and mcs index is 11, "iw link"
command would show "tx bitrate: 108.0 MBit/s" without this patch.
Now it shows "tx bitrate: 108.0 MBit/s MCS 11 40Mhz" with the patch.
Cc: "3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After FW download, activate new FW by invoking FW reset.
Recreate rings once new FW is operational.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke only required initialization routines for Lancer.
Remove invocation of unnecessary routines.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query die temperature stat for Lancer to report it correctly
in ethtool.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autonegotiation of pause parameters is possible only on some PHYs.
Ability of autoneg of pause parameters is reported by adapter.
Autoneg of pause parameters cannot be changed from driver.
Fix driver to give error when autoneg mode is toggled by user.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First update the adapter variables with the current speed and
mode before fire the notification. Otherwise, the get_settings()
may provide old values.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"retval" has to be a signed integer for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the kmem cache API doesn't internally allocate
the name but just points to the name that was passed
in we can't use stack memory for it. Move the name
into the transport struct.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.
To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.
Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
info->control.sta may only be dereferenced during the drv_tx call otherwise
could lead to use-after-free bugs
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This stashes away this feature from standard kernel builds.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO support in this driver was intended to support the iwmc3200
device. This hardware never became available to normal humans.
Leaving this driver imposes unwelcome maintenance costs for no clear
benefit.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Data pointer on rt2x00queue_for_each_entry() is never used - remove it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge 3290 and 5390 POWER_BOUND and FREQ_OFFSET_BOUND defines.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix indention and remove unnecessary brackets and compares.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an alternative tx status path
for BlockAck Requests as the hardware doesn't
recognize that a BlockAck Requests is usually
acked with a BlockAck and not a legacy ACK.
Without this patch, the stack would constantly
resent old and stale BARs. So, depending on the
receiver stack, this could lead to:
- "stuck" ba sessions and package loss, as the
stale BAR would reset the sequence each time.
- lots of reorder releases.
- ...
Reported-by: Sean Patrick Santos <quantheory@gmail.com>
Reported-by: Mikołaj Kuligowski <mikolaj.q@wp.pl>
Reported-by: Per-Erik Westerberg <per-erik.westerberg@bredband.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify mlx4_dev_cap to allow IB support when SR-IOV is active. Modify
mlx4_slave_cap to set the "rdma-supported" bit in its flags area, and
pass that to the guests (this is done in QUERY_FUNC_CAP and its
wrapper).
However, we don't activate IB support quite yet -- we leave the error
return at the start of mlx4_ib_add in the mlx4_ib driver.
In addition, set "protected fmr supported" bit to zero in the
QUERY_FUNC_CAP wrapper.
Finally, in the QUERY_FUNC_CAP wrapper, we needed to add code which
checks for the port type (IB or Ethernet). Previously, this was not
an issue, since only Ethernet ports were supported.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests. These proxy QPs
send their packets to a "tunnel" QP owned by the master. The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.
For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key. These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.
This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.
The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.
In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.
The QPNs for these QPs are arranged as follows:
1. The real SQP numbers (8)
2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)
To support these QPs, two new fields are added to struct mlx4_dev:
base_sqp: this is the QP number of the first of the real SQPs
base_tunnel_sqp: this is the qp number of the first qp in the tunnel
sqp region. (On guests, this is the first tunnel
sqp of the 8 which are assigned to that guest).
In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region. (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)
Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In mlx4_init_icm_table(), free the allocated table if we failed to
allocate memory to its entries.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Spotted four duplicate declarations in icm.h, remove them.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There are really only 3 modes that can control the number of queues. Those
are RSS, DCB, and VMDq/SR-IOV. Currently we have things much more broken
up than they need to be for how we are configuring the rings. In order to
try and straiten some of this out I am going to start merging similar
functionality into single functions. To start with I am merging the Flow
Director ring configuration into the RSS ring configuration since Flow
Director cannot function with DCB or SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mask value for ring features was overloaded for FCoE which can lead to
some confusion. In order to avoid any confusion I am splitting the mask
value and adding an offset value. This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently using indices to indicate the upper limit on a ring
feature. However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to count q_vectors instead of MSI-X
vectors. We were using num_msix_vectors to find the number of q_vectors in
multiple places. This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 6d29b1ef introduces a bug, ntohs is __be16_to_cpu,
not cpu_to_be16.
We always use htons on IP_OFFSET and IP_MF, then compare
with network package.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, Using htons on skb->protocol is wrong.
And fix two code style issues: indentation and remove
unnecessary parentheses.
CC: Tristram Ha <Tristram.Ha@micrel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address
when it gets to the last entry of the tx ring. We were not using
the proper macro to skip the last entry when advancing the tx index.
Reported-by: Zongyun Lai <zlai@vmware.com>
Reviewed-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing case was causing ethtool self test to print garbage
value in extra info section.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
