Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f85 ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
c94e267766
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
refers to this bit as "bit 1 of the status register 2".
Rename the macro accordingly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Test that all the bits from Status Register 1 and Status Register 2
were written correctly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_unlock() unlocks blocks of memory or the entire flash memory
array, if requested. clear_sr_bp() unlocks the entire flash memory
array at boot time. This calls for some unification, clear_sr_bp() is
just an optimization for the case when the unlock request covers the
entire flash size.
Get rid of clear_sr_bp() and introduce spi_nor_unlock_all(), which is
just a call to spi_nor_unlock() for the entire flash memory array.
This fixes a bug that was present in spi_nor_spansion_clear_sr_bp().
When the QE bit was zero, we used the Write Status (01h) command with
one data byte, which might cleared the Status Register 2. We now always
use the Write Status (01h) command with two data bytes when
SNOR_F_HAS_16BIT_SR is set, to avoid clearing the Status Register 2.
The SNOR_F_NO_READ_CR case is treated as well. When the flash doesn't
support the CR Read command, we make an assumption about the value of
the QE bit. In spi_nor_init(), call spi_nor_quad_enable() first, then
spi_nor_unlock_all(), so that at the spi_nor_unlock_all() time we can
be sure the QE bit has value one, because of the previous call to
spi_nor_quad_enable().
Get rid of the MFR handling and implement specific manufacturer
default_init() fixup hooks.
Note that this changes a bit the logic for the SNOR_MFR_ATMEL,
SNOR_MFR_INTEL and SNOR_MFR_SST cases. Before this patch, the Atmel,
Intel and SST chips did not set the locking ops, but unlocked the entire
flash at boot time, while now they are setting the locking ops to
stm_locking_ops. This should work, since the disable of the block
protection at the boot time used the same Status Register bits to unlock
the flash, as in the stm_locking_ops case.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Make sure that when doing a lock() or an unlock() operation we don't clear
the QE bit from Status Register 2.
JESD216 revB or later offers information about the *default* Status
Register commands to use (see BFPT DWORDS[15], bits 22:20). In this
standard, Status Register 1 refers to the first data byte transferred on a
Read Status (05h) or Write Status (01h) command. Status register 2 refers
to the byte read using instruction 35h. Status register 2 is the second
byte transferred in a Write Status (01h) command.
Industry naming and definitions of these Status Registers may differ.
The definitions are described in JESD216B, BFPT DWORDS[15], bits 22:20.
There are cases in which writing only one byte to the Status Register 1
has the side-effect of clearing Status Register 2 and implicitly the Quad
Enable bit. This side-effect is hit just by the
BFPT_DWORD15_QER_SR2_BIT1_BUGGY and BFPT_DWORD15_QER_SR2_BIT1 cases.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Check that all the bits written in the write_sr_and_check() method
match the status_new received value. Failing to write the other bits
is dangerous too, extend the check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
When the Read-Modify-Write-Read-Back Quad Enable methods failed on
the Read-Back, they returned -EINVAL. Since this is an I/O error,
return -EIO.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop the default spansion_quad_enable() method and replace it with
spansion_read_cr_quad_enable().
The function was buggy, it didn't care about the previous values
of the Status and Configuration Registers. spansion_read_cr_quad_enable()
is a Read-Modify-Write-Check function that keeps track of what were
the previous values of the Status and Configuration Registers.
In terms of instruction types sent to the flash, the only difference
between the spansion_quad_enable() and spansion_read_cr_quad_enable()
is that the later calls spi_nor_read_sr(). We can safely assume that all
flashes support spi_nor_read_sr(), because all flashes call it in
spi_nor_sr_ready(). The transition from spansion_quad_enable() to
spansion_read_cr_quad_enable() will not affect anybody, drop the buggy
code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
static int spi_nor_write_sr(struct spi_nor *nor, u8 val)
static int spi_nor_write_sr_cr(struct spi_nor *nor, const u8 *sr_cr)
into
static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
The Status Register can be written with one or two bytes. Merge
the two functions to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.
Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Check for the return vales of each Register Operation.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.
Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.
Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.
Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.
Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: Jethro Beekman <jethro@fortanix.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
n25q512a was rebranded to mt25qu512a after its spin off from STM.
mt25qu512a is different only in terms of operating frequency, the
JEDEC id is the same as in n25q512a.
Dual reads are supported (0x3b, 0x3c), set the SPI_NOR_DUAL_READ flag.
4-byte opcodes are supported, set the SPI_NOR_4B_OPCODES flag.
Tested Single I/O and QUAD I/O mode on LS1046FRWY.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: rename entry to "mt25qu512a (n25q512a)",
reword commit message, order entry by size, drop comment as it looked
redundant]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We already pass a pointer to nor, we can obtain the sector_size
by dereferencing it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch adds spi_nor_debugfs_init() for the debugfs initialization.
With this patch, we can read the partname and partid through the
debugfs.
The output of new debugfs nodes on my device are:
cat /sys/kernel/debug/mtd/mtd0/partid
spi-nor:ef6017
cat /sys/kernel/debug/mtd/mtd0/partname
w25q64dw
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put before
the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a break from the middle of the loop, there is
no put, thus causing a memory leak. Upon termination of the loop
(whether by break or a natural exit), either ret will have a non-zero
value or child will be NULL. Hence add an of_node_put() that will
execute only when ret has a non-zero value, as calling of_node_put() on
a possible NULL value does not cause any further issues.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Dedicate a function for getting the pointer to the flash_info
const struct. Trim a bit the spi_nor_scan() huge function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Parsing of flash parameters were interleaved with setting of the
nor addr width. Dedicate a function for setting nor addr width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
S3AN flashes use a specific opcode to read the status register.
We currently use the SPI_S3AN flag to decide whether this specific
SR read opcode should be used, but SPI_S3AN is about to disappear, so
let's add a new flag.
Note that we use the same bit as SPI_S3AN implies SPI_NOR_XSR_RDY and
vice versa.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
s3an_nor_scan() was overriding the opcode selection done in
spi_nor_default_setup(). Set nor->setup() method in order to
avoid the unnecessary call to spi_nor_default_setup().
Now that the call to spi_nor_default_setup() is skipped, set
mtd.erasesize to nor->info->sector_size, as it was when
spi_nor_select_erase() was called.
No dummy byte is required for the S3AN's Random Read command (0x03),
so no need to set nor->read_dummy.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
nor->params.setup() configures the SPI NOR memory. Useful for SPI NOR
flashes that have peculiarities to the SPI NOR standard, e.g.
different opcodes, specific address calculation, page size, etc.
Right now the only user will be the S3AN chips, but other
manufacturers can implement it if needed.
Move spi_nor_setup() related code in order to avoid a forward
declaration to spi_nor_default_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
In order to separate manufacturer quirks from the core we need to get
rid of all the manufacturer specific flags, like the
SNOR_F_S3AN_ADDR_DEFAULT one.
This can easily be replaced by a ->convert_addr() hook, which when
implemented will provide the core with an easy way to convert an
absolute address into something the flash understands.
Right now the only user are the S3AN chips, but other manufacturers
can implement it if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add a spansion_post_sfdp_fixups() function to fix the erase opcode,
erase sector size and set the SNOR_F_4B_OPCODES flag.
This way, all spansion related quirks are placed in the
spansion_post_sfdp_fixups() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
SFDP tables are sometimes wrong and we need a way to override the
config chosen by the SFDP parsing logic without discarding all of it.
Add a new hook called after the SFDP parsing has taken place to deal
with such problems.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the SNOR_F_HAS_LOCK flag and set it when SPI_NOR_HAS_LOCK is set
in the flash_info entry or when it's a Micron or ST flash.
Move the locking hooks in a separate struct so that we have just
one field to update when we change the locking implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook, introduce
spi_nor_late_init_params(), set ops in nor->params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The procedure used to enable 4 byte addressing mode depends on the NOR
device, so let's provide a hook so that manufacturer specific handling
can be implemented in a sane way.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use nor->params.set_4byte() instead of
nor->set_4byte()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add functions to delimit what the chunks of code do:
static void spi_nor_init_params()
{
spi_nor_info_init_params()
spi_nor_manufacturer_init_params()
spi_nor_sfdp_init_params()
}
Add descriptions to all methods.
spi_nor_init_params() becomes of type void, as all its children
return void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The goal is to move the quad_enable manufacturer specific init in the
nor->manufacturer->fixups->default_init()
The legacy quad_enable() implementation is spansion_quad_enable(),
select this method by default.
Set specific manufacturer fixups->default_init() hooks to overwrite
the default quad_enable() implementation when needed.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
gd25q256 needs to tweak the ->quad_enable() implementation and the
->default_init() fixup hook is the perfect place to do that. This way,
if we ever need to tweak more things for this flash, we won't have to
add new fields in flash_info.
We can get rid of the flash_info->quad_enable field as gd25q256 was
the only user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[tudor.ambarus@microchip.com: use ->default_init() hook instead of
->post_sfdp()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
As of now, the flash parameters initialization logic is as following:
a/ default flash parameters init in spi_nor_init_params()
b/ manufacturer specific flash parameters updates, split across entire
spi-nor core code
c/ flash parameters updates based on SFDP tables
d/ post BFPT flash parameter updates
In the quest of removing the manufacturer specific code from the spi-nor
core, we want to impose a timeline/priority on how the flash parameters
are updated. The following sequence of calls is pursued:
1/ spi-nor core parameters init based on 'flash_info' struct:
spi_nor_info_init_params()
which can be overwritten by:
2/ MFR-based manufacturer flash parameters init:
nor->manufacturer->fixups->default_init()
which can be overwritten by:
3/ specific flash_info tweeks done when decisions can not be done just on
MFR:
nor->info->fixups->default_init()
which can be overwritten by:
4/ SFDP tables flash parameters init - SFDP knows better:
spi_nor_sfdp_init_params()
which can be overwritten by:
5/ post SFDP tables flash parameters updates - in case manufacturers get
the serial flash tables wrong or incomplete.
nor->info->fixups->post_sfdp()
The later can be extended to nor->manufacturer->fixups->post_sfdp() if
needed.
This patch opens doors for steps 2/ and 3/.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Move the SMPT parsed erase map
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.
Please note that there is a roll-back mechanism for the flash
parameter and settings, for cases when SFDP parser fails. The SFDP
parser receives a Stack allocated copy of nor->params, called
sfdp_params, and uses it to retrieve the serial flash discoverable
parameters. JESD216 SFDP is a standard and has a higher priority
than the default initialized flash parameters, so will overwrite the
sfdp_params data when needed. All SFDP code uses the local copy of
nor->params, that will overwrite it in the end, if the parser succeds.
Saving and restoring the nor->params.erase_map is no longer needed,
since the SFDP code does not touch it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
All flash parameters and settings should reside inside
'struct spi_nor_flash_parameter'. Drop the local copy of
quad_enable() and use the one from 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The Flash parameters and settings are now stored in 'struct spi_nor'.
Use this instead of the stack allocated params.
Few functions stop passing pointer to params, as they can get it from
'struct spi_nor'. spi_nor_parse_sfdp() and children will keep passing
pointer to params because of the roll-back mechanism: in case the
parsing of SFDP fails, the legacy flash parameter and settings will be
restored.
Zeroing params is no longer needed because all SPI NOR users kzalloc
'struct spi_nor'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The scope is to move all [FLASH-SPECIFIC] parameters and settings
from 'struct spi_nor' to 'struct spi_nor_flash_parameter'.
'struct spi_nor_flash_parameter' describes the hardware capabilities
and associated settings of the SPI NOR flash memory. It includes
legacy flash parameters and settings that can be overwritten by the
spi_nor_fixups hooks, or dynamically when parsing the JESD216
Serial Flash Discoverable Parameters (SFDP) tables. All SFDP params
and settings will fit inside 'struct spi_nor_flash_parameter'.
Move spi_nor_hwcaps related code to avoid forward declarations.
Add a forward declaration that we can't avoid: 'struct spi_nor' will
be used in 'struct spi_nor_flash_parameter'.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl1i2wkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGcDQIAJINYON5WdDSFDpp
htva213hSIxYLix8Dc4cTMk8qT/P2MAj9pPYERuLwIxWZlfbduW6Fxy8bJANZ7k3
4cJ/IbmA5M5ZIaOJTTL45w8H0CMR/4mdPl5rb5k/Wkh449Cj101gZLlh0FEtR5zG
uDJecKSuHjH1ikySk6+zmRG5X+lq6wNY8NkuBtfwAwLffFc0ljQHwPUMJ8ojgqt/
p3ChNgtb/I6U6ExITlyktKdP59bAoHAoBiKKFZWw5yJWgXE2q4Sv9nT4Btkr5KdJ
9mnWnSaSLwptNCOtU4tKLwFIZP2WoVXGPNxxq4XLoTEuieXCqmikhc9tSSTwk+Tp
CKHN6wU=
=JkJ4
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl1mS78ACgkQS1VPR6WN
FOnqOwgAqerjkyzyleXrzvLVaUUhT4MrykMljakHFX6zt+ipi74bdOQRF+uG2A4v
DnhYXGfEiIRNco/4NkXEKWsOBKoWUIUISpxuBBRmEJEL9Y23WJ1czy8rPEWoVff3
BUY6sJ0kmltikRh0hBZhABa0lkbimV3WGiVB5ATpsO2whdJz3tN+k4GjWq12Sbls
V+ioN7eeJSRuufwVSFT3YcGT7uRX6/Fq21fX4XkWJp3IaftD8eo5pkO+XQFIeBKw
xB7g2zkkDG//jnzodjSc2RcpXda1i4a8Yx+6J2KJw7x1F5JVQN4VgmsARPFWsCID
Q7uhWqCVdW6cSBebwkHC1xf4fZSRmw==
=x4If
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rc6' into spi-nor/next
Linux 5.3-rc6
Merge back latest release candidate, to include a fix that
we depend on for new development:
834de5c1aa ("mtd: spi-nor: Fix the disabling of write protection at init")
spi-nor.c issues 4B commands for some Flash chips bigger than 16Mbytes.
Xeon(R) D-1500 documentation mentions its Integrated PCH Logic supports
Flash chips up to 64Mbytes.
D-1500 Integrated PCH documenation however has inconsistencies regarding
FADDR register width and says nothing about particular commands issued
to support 64Mbytes of Flash.
Nevetheless the tests on Xeon(R) CPU D-1548 with 512Mbit Flash chips
Macronix MX25L51245G and Micron MT25QL512A showed that erase, write and
read operations work just fine after SPINOR_OP_READ_4B and
SPINOR_OP_READ_FAST_4B are white-listed (currently only
SPINOR_OP_READ_FAST_4B is used and only for Macronix).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In spi_nor_parse_4bait(), 'dwords' is allocated through kmalloc(). However,
it is not deallocated in the following execution if spi_nor_read_sfdp()
fails, leading to a memory leak. To fix this issue, free 'dwords' before
returning the error.
Fixes: 816873eaee ("mtd: spi-nor: parse SFDP 4-byte Address Instruction Table")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The problem is that if "ret" is negative then when we check if
"ret > len", that condition is going to be true because of type
promotion. So this patch re-orders the code to check for negatives
first and preserve those error codes.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The current Cadence QSPI driver sometimes caused a
"rcu_sched self-detected stall" while writing large files.
Stall Report:
'# mtd_debug write /dev/mtd1 0 48816464 blob.img
[ 1815.454227] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1815.459789] rcu: 0-....: (2099 ticks this GP) idle=8c6/1/0x40000002
softirq=6492/6492 fqs=935
[ 1815.468442] rcu: (t=2100 jiffies g=8749 q=247)
<snip> (abbreviated backtrace)
[ 1815.772086] [<c05a3ea0>] (cqspi_exec_flash_cmd) (cqspi_read_reg)
[ 1815.786203] [<c05a5488>] (cqspi_read_reg) from (read_sr)
[ 1815.803790] [<c05a0330>] (read_sr) from
(spi_nor_wait_till_ready_with_timeout)
[ 1815.816610] [<c05a182c>] (spi_nor_wait_till_ready_with_timeout) from
(spi_nor_write+0x104/0x1d0)
[ 1815.836791] [<c05a1a44>] (spi_nor_write) from (part_write+0x50/0x58)
<snip>
[ 1815.997961] cadence-qspi ff809000.spi: Flash command execution timed out.
[ 1816.004733] error -110 reading SR
file_to_flash: write, size 0x2e8e150, n 0x2e8e150
write(): Connection timed out
This was caused by a tight loop in cqspi_wait_for_bit(). Fix by using
readl_relaxed_poll_timeout() which sleeps 10us while polling a register.
Fit onto 80 character line by truncating the bool clear parameter
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Currently, the Top/Bottom protection function (SPI_NOR_HAS_TB) is
implemented to fit some flashes with TB bit on SR.
s25fl512s has TBPROT bit on CR1, so the TB protection is not working on it.
Fix the wrong flag on s25fl512s.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Tiger Lake has the same SPI serial flash controller as Ice Lake.
Add Tiger Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This commit adds support for the SST sst26wf016b flash memory IC.
This IC was tested with "snps,dw-apb-ssi" SPI controller.
We don't test dual/quad reads however sst26wf016b flash's datasheet
advertises both dual and quad reads (and support of corresponding
commands)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Similar to w25q256 (besides not supporting QPI mode) but with different ID.
The "JVM" suffix is in the datasheet.
The datasheet indicates DUAL and QUAD are supported.
https://www.winbond.com/resource-files/w25q256jv%20spi%20revi%2010232018%20plus.pdf
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_spansion_clear_sr_bp() depends on spansion_quad_enable().
While spansion_quad_enable() is selected as default when
initializing the flash parameters, the nor->quad_enable() method
can be overwritten later on when parsing BFPT.
Select the write protection disable mechanism at spi_nor_init() time,
when the nor->quad_enable() method is already known.
Fixes: 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op() when
nor->spimem != NULL.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The m25p80 driver is actually a generic wrapper around the spi-mem
layer. Not only the driver name is misleading, but we'd expect such a
common logic to be directly available in the core. Another reason for
moving this code is that SPI NOR controller drivers should
progressively be replaced by SPI controller drivers implementing the
spi_mem_ops interface, and when the conversion is done, we should have
a single spi-nor driver directly interfacing with the spi-mem layer.
While moving the code we also fix a longstanding issue when
non-DMA-able buffers are passed by the MTD layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi-mem layer expects all buffers passed to it to be DMA'able. But
spi-nor layer mostly allocates buffers on stack for reading/writing to
registers and therefore are not DMA'able. Introduce bounce buffer to be
used to read/write to registers. This ensures that buffer passed to
spi-mem layer during register read/writes is DMA'able. With this change
nor->cmd-buf is no longer used, so drop it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl0V1XYACgkQS1VPR6WN
FOkBbQf+Iv2+vmoDGDCVGO4LZh+N/l0Sh/C31hJj5y7GVkCdwMJCvdOrGEhDkseu
Dc0gchT6uy52pAp4N0B88avC8fSJY0UwFRbnqUUA546R9Uf6h+gbGIZCX/rzZuIi
IDDNHc06qbpxpesfC5CowhY49QVGG+O0scgUOE2gKHOfd04kXu6gqIV0BvQZg80R
EpSgifHLUk/b2015FyqB5YFuc2K3HMmcWc6uJx4kSHPCXiCOx8aaEqjKvK9vL0h5
XOxXim5HhuzFqQ8vSPqvnKDokkuV3pcSUcaQyjQjrebTlectaDjGZlLF17Udm9Q9
I0zI+7deXK9L4roatEryzOdW0Ql3Hw==
=J5Uw
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.3-v2' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]
The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.
[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
Suggested-by: Tien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
IS25LP256 gets BFPT_DWORD1_ADDRESS_BYTES_3_ONLY from BFPT table for
address width. But in actual fact the flash can support 4-byte address.
Use a post bfpt fixup hook to overwrite the address width advertised by
the BFPT.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0Pwk0ACgkQJWrqGEe9
VoS8nwf7B76jN39/g32Hfp4JT/B7cntrHzTGxfUT9NAhKa4MaI7FOU2eeTryaVdO
32OJlttV+r0Fu6p+In1VXCk4j1YlkcOaxqB1VXsMEaQ+Vt8ONVTbJX/cqyGC/ogq
MZlO8Rys4MGmq7vRiZ+1SD8lOV4qXgmX3D38NjUQ1oCAMCCgJgkWYFV2tv9Eie09
2CCT3IBFj+D34qaBiM+qocGtnzWfB9477A6ZeI4BwjUe1ZtoEYeIOrCXWiywabjM
msHRN1tNt5kfINnx0TkQFcnpbdDo5tMyTHCkEQt5Ewdae4vyCv7xTHTCZEttC7Ic
Rx2yONzrZGQVP4c27y22K954C1jGcg==
=ZiPm
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
This gets rid of the license boilerplate duplicated in each file.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Elkhart Lake has the same SPI serial flash controller as Ice Lake.
Add Elkhart Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Testing done on Mikrotik Routerboard RB450Gx4 board under
4.14.119 and 4.19.43 kernels. The test board does not support
Dual or Quad modes.
Datasheet at:
https://www.winbond.com/resource-files/w25q16jv%20spi%20revg%2003222018%20plus.pdf
Signed-off-by: Robert Marko <robimarko@gmail.com>
[tudor.ambarus@microchip.com: w25q16jv-im/jm and w25q16jv-iq/jq
have different jedec ids, fix flash name.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of SPI error during the reading of the nor Id,
the probe fails without any error message related to
the JEDEC Id reading procedure.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add an entry for Micron MT25QL02 which is a 3V variant of already
supported MT25QU02.
Testing was done on a ZII VF610 Dev Board (rev. B).
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
[tudor.ambarus@microchip.com: order entry alphabetically, wrap to
80 chars limit]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.
The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Comet Lake has the same SPI serial flash controller as Ice Lake.
Add Comet Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Both the BP[0-2] bits and the TBPROT bit are supported on this chip.
Tested and verified on a Cypress s25fl512s.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It was observed that reads crossing 4K address boundary are failing.
This limitation is mentioned in Intel documents:
Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:
"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."
Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):
"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."
Avoid this by splitting an operation crossing the boundary into two
operations.
Fixes: 8afda8b26d ("spi-nor: Add support for Intel SPI serial flash controller")
Cc: stable@vger.kernel.org
Reported-by: Romain Porte <romain.porte@nokia.com>
Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If identification of an SPI NOR FLASH fails, the JEDEC ID is printed,
which is stored in the first 3 bytes of the ID read from the FLASH.
However, the extended JEDEC ID, which is stored in the remaining bytes,
also matters, as it is used for identification of some FLASH types.
Print all (currently 6) ID bytes read to ease failure analysis and
debugging.
Suggested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip found
on recent wireless routers. Its 32, 128 and 256 Mbit siblings
are already supported.
Tested on a COMFAST CF-E120A v3 router board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This adds support for the Macronix MX25V8035F, a 8Mb SPI NOR chip.
It is used on i.MX6UL/ULL SoMs by Kontron Electronics GmbH (N631x).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
It is used on i.MX6 boards by Kontron Electronics GmbH
(N60xx, N61xx).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: Ahmet Celenk <ahmet.celenk@procenne.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.
This patch allows all the 8 bytes to be written.
Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The mx25u3235f is found on the ZyXEL NBG6817 router, therefore
add driver support for it so that we can upstream board support.
Minimal tested with u-boot tools fw_printenv/fw_setenv on GlobalScale
ESPRESSObin v5 board.
Signed-off-by: André Valentin <avalentin@marcant.net>
[miyatsu@qq.com: Remove unnecessary white space.]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Spansion S25FL512S ID is erroneously using 5-byte JEDEC ID, while the chip
family ID is stored in the 6th byte. Due to using only 5-byte ID, it's also
covering S25FS512S and now that we have added 6-byte ID for that chip, we
can convert S25FL512S to using a proper 6-byte ID as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Spansion S25FS512S flash is currently misdetected as S25FL512S since the
latter uses 5-byte JEDEC ID, while the 6th ID byte (family ID) is different
on those chips. Add the 6-byte S25FS512S ID before S25FL512S ID in order
not to break the existing S25FS512S users.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Add octal read flag for flash mt35xu512aba.
This flash, mt35xu512aba, is only complaint to SFDP JESD216B and does
not seem to support newer JESD216C standard that provides auto
detection of Octal mode capabilities and opcodes. Therefore, this
capability is manually added using new SPI_NOR_OCTAL_READ flag.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
- Add opcodes for octal I/O commands
* Read : 1-1-8 and 1-8-8 protocol
* Write : 1-1-8 and 1-8-8 protocol
* opcodes for 4-byte address mode command
- Entry of macros in _convert_3to4_xxx function
- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
commands. This flag is required for flashes which didn't provides
support for auto detection of Octal mode capabilities i.e. not
seems to support newer JESD216C standard.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The quadspi is a generic communication interface which could be shared
with other MediaTek SoCs. Hence rename it to a common one.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
SNOR_HWCAPS_READ should be supported by this controller, so add this
flag to spi_nor_hwcaps mask.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
There's a new driver using the SPI memory interface of the SPI framework
at spi/spi-fsl-qspi.c, which can be used together with m25p80.c to
replace the functionality of this SPI NOR driver.
The new driver is already in use and this code is not compiled anymore,
so let's remove it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Acked-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).
The controller does not support generic SPI messages.
This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while for
controller features designed to make them perform better but it's not
worked out as well as hoped so the interface has been redesigned in a
way that will hopefully do better - it's already been adopted by a
number of additional controllers so things are looking good. Otherwise
most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris Brezillon
and Yogesh Narayan Gaur plus usage of it in several drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhLBsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AGvB/9odNqLjVJiG6v0EIKqLyYXMzCYgmrZ
RyBZoqTKoNmXxv0b/Fdsi8VaiJ8x2WIcqLzhpQlg3twOCvXQbgoA+JzQNyHZlZ1u
8cxfFGebVS6r0k14bkmAVR8LSvGlReOZQLC2MvccVc/UAwN0/p5ncN0xUADHvIOW
/Pmx0/e2uCMx1+OMAudlUXQ5IIbnb5/OjvDfR/7tlVo5YKSgkHBJeunOYSaPSNuO
QNf9+kZxvQ8djYbpYqqHWovPF7JSlQAj0WkMJPB/g3R09E/vatSBlCMnETBJWn/L
wogHquLK/vwRaS+MqTSrGsi0ylpqgxmZrbGKcXKF51fim0EvBg7cMqe6
=ZnI3
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
The is25lp016d is found on the iwg23s from iWave, therefore
add driver support for it so that we can upstream board support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This
table is optional but when available, we parse it to get the 4-byte
address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte
address mode or setting the Base Address Register (BAR).
Flashes that have the 4BAIT table declared can now support
SPINOR_OP_PP_1_1_4_4B and SPINOR_OP_PP_1_4_4_4B opcodes.
Tested on MX25L25673G.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- rework erase and page program logic,
- pass DMA-able buffer to spi_nor_read_sfdp(),
- introduce SPI_NOR_HAS_4BAIT
- various minor updates.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The is25lp256 supports 4-byte opcodes and quad output.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add SPDX tags to replace the license boiler-plate and fix the
MODULE_LICENSE() definition in spi-nor.c to match the license text
(GPL v2).
Interestingly, spi-nor.h and spi-nor.c do not use the same license
(GPL v2+ for spi-nor.h, GPL v2 for spi-nor.c).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
No need to use an integer when the value is either true or false.
Make it a boolean.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Some functions called from spi_nor_scan() need a flash_info object.
Let's assign nor->info early on to avoid passing info as an extra
argument to each of these sub-functions.
We also stop passing a flash_info object to set_4byte() and use
nor->info directly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reorganize the code to kill forward declarations of spi_nor_match_id()
macronix_quad_enable() and spi_nor_hwcaps_read2cmd().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
gcc should be smart enough to decide when inlining a function makes
sense. Drop all inline specifiers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
MX25L25635F and MX25L25635E share the same JEDEC-ID, but the F variant
supports 4-byte opcodes while the E variant doesn't. We need a way to
differentiate those 2 chips and set the SNOR_F_4B_OPCODES flag only for
the F variant.
Luckily, 4-byte opcode support is not the only difference: Fast Read
4-4-4 is only supported by the F variant, and this feature is
advertised in the BFPT table. Use this to decide when to set the
SNOR_F_4B_OPCODES flag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Experience has proven that SFDP tables are sometimes wrong, and parsing
of these broken tables can lead to erroneous flash config.
This leaves us 2 options:
1/ set the SPI_NOR_SKIP_SFDP flag and completely ignore SFDP parsing
2/ fix things at runtime
While #1 should always work, it might imply extra work if most of the
SFDP is correct. #2 has the benefit of keeping the generic SFDP parsing
logic almost untouched while allowing SPI NOR manufacturer drivers to
fix the broken bits.
Add a spi_nor_fixups struct where we'll put all our fixup hooks, each
of them being called at a different point in the scan process.
We start a hook called just after the BFPT parsing to allow fixing up
info extracted from the BFPT section. More hooks will be added if other
sections need to be fixed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
