When calling napi_disable during reset down process, if NAPIF_STATE_MISSED
is set, napi_complete will call __napi_schedule to do the polling again.
So this patch uses HNS3_NIC_STATE_DOWN to ensure the polling is not
scheduled again.
Also, when napi_complete returns true, it means polling is scheduled
again, it is not neccssary to enable the interrupt.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclgevf_reset() may fail for some reasons, so it needs an error
handler to deal with it. When VF reset failed, VF can only be restored
by a higher level reset asserted by PF. So, it needs to reinitialize
its command queue, then it can respond to higher level reset.
Also, this patch adds error logging in the hclgevf_notify_client().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware's description, after the reset occurs, the driver
needs to re-initialize the command queue before sending and receiving
any commands. Therefore, the VF's driver needs to identify the command
queue needs to re-initialize with HCLGEVF_STATE_CMD_DISABLE, and does
not allow sending or receiving commands before the re-initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Core/Global/IMP reset occurs, the hardware sets the reset status
register of all PF/VF and reports a reset interrupt to all PF/VF and
firmware.
When receiving the reset interrupt:
1. The firmware will wait for 100 ms before resetting the hardware and
clear the reset status register of all PF when hardware reset is done.
2. The PF/VF driver needs to down the netdev within 100 ms and then wait
for hardware reset to finish.
3. After firmware clearing the reset status register of all PF, the PF
driver reinitializes the hardware and clear the reset status register
of it's VF.
4. After PF driver clearing the reset status register of VF, the VF driver
reinitializes the hardware.
This patch mainly add handling for the step 4.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.
Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.
Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.
This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.
Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.
hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, the reset handling function only need to
reinitialize hardware, it makes sense to add a function to
do that job. Also the error handling of hclgevf_init_hdev is
different when it is used in reset process.
This patch adds reset_hdev to reinitialize hardware when resetting.
Also, this patch removes the hclgevf_dev_ongoing_full_reset because
it is unused now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Checksum offloads could not be configured and ignored netdev features
flag for checksumming.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.
The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.
Fixes: 94b3b54230 ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.
Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.
This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control statuses were not synchronized between blocks,
that caused packets/link drop on some corner cases, when
MAC sent PFC although Phy was not expecting these to come.
Driver should readout the negotiated FC from phy and
configure RX block accordigly.
This is done on each link change event with information from FW.
Fixes: 288551de45 ("net: aquantia: Implement rx/tx flow control ethtools callback")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_hlist was initialized during adapter_up, which will be called
every time a vf device is first brought up, or every time when device
is brought up again after bringing all devices down. This means our
state of previous list is lost, causing a memleak if entries are
present in the list. To fix that, move list init to the condition
that performs initial one time adapter setup.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RED Qdisc will now inform the drivers about the state of the harddrop
flag. Refuse to offload in case harddrop is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out the threshold value is used in signed compares in the FW,
so we should avoid setting the top bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve log messages printed when RED can't be offloaded because
of Qdisc parameters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases initialization logic which follows allocation of
the vNIC structure may want to validate the capabilities of that vNIC.
This is easy before vNIC is initialized for normal capabilities which
are at fixed offsets in control memory, easy to locate and read, but
poses a challenge if the capabilities are in form of TLVs. Parse
the TLVs early on so other code can just access parsed info, instead
of having to do the parsing by itself.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting ctrl_bar pointer to the nfp_net_alloc function,
to make sure we can parse capabilities early in the following
patch.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qdisc offload code is logically separate, and we will soon
do significant surgery on it to support more Qdiscs, so move
it to a separate file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan configuration is not restored after interface donw/up sequence
(if dual-emac - both interfaces). Tested on am572x EVM.
Steps to check:
~# ip link add link eth1 name eth1.100 type vlan id 100
~# ifconfig eth0 down
~# ifconfig eth1 down
Try to remove vid and observe warning:
~# ip link del eth1.100
[ 739.526757] net eth1: removing vlanid 100 from vlan filter
[ 739.533322] failed to kill vid 0081/100 for device eth1
This patch fixes it, restoring only vlan ALE entries and all other
unicast/multicast entries are restored by system calling rx_mode ndo.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment, mcast addresses are added for real device only
(reserved vlans for dual-emac mode), even if a mcast address was added
for some vlan only, thus ALE doesn't have corresponding vlan mcast
entries after vlan socket joined multicast group. So ALE drops vlan
frames with mcast addresses intended for vlans and potentially can
receive mcast frames for base ndev. That's not correct. So, fix it by
creating only vlan/mcast entries as requested. Patch doesn't use any
additional lists and is based on device mc address list and cpsw ALE
table entries.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As added in 3e59020abf ("net: bql: add __netdev_tx_sent_queue()"), which
see for performance rationale.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just removes VLAN_TAG_PRESENT use. VLAN TCI=0 special meaning is
deeply embedded in the driver code and so is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping problems with packets > 8191 as shown:
PING 192.168.1.99 (192.168.1.99) 8150(8178) bytes of data.
8158 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=0.669 ms
wrong data byte 8144 should be 0xd0 but was 0x0
16 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
%< ---------------snip--------------------------------------
8112 b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 ba bb bc bd be bf
c0 c1 c2 c3 c4 c5 c6 c7 c8 c9 ca cb cc cd ce cf
8144 0 0 0 0 d0 d1
^^^^^^^
Notice the 4 bytes of 0 before the expected byte of d0.
Databook notes that the RX buffer must be a multiple of 4/8/16
bytes [1].
Update the DMA Buffer size define to 8188 instead of 8192. Remove
the -1 from the RX buffer size allocations and use the new
DMA Buffer size directly.
[1] Synopsys DesignWare Cores Ethernet MAC Universal v3.70a
[section 8.4.2 - Table 8-24]
Tested on SoCFPGA Stratix10 with ping sweep from 100 to 8300 byte packets.
Fixes: 286a837217 ("stmmac: add CHAINED descriptor mode support (V4)")
Suggested-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return -ENOMEM directly instead of assigning it in a variable
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver dynamically allocates an skb and maps it as DMA Rx
buffer. In order to prepare for upcoming XDP changes, let's introduce a
different allocation scheme.
Buffers are allocated dynamically and mapped into hardware.
During the Rx operation the driver uses build_skb() to produce the
necessary buffers for the network stack.
This change increases performance ~15% on 64b packets with smmu disabled
and ~5% with smmu enabled
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interferences on the SPI line could distort the response of
available buffer space. So at least we should check that the
response doesn't exceed the maximum available buffer space.
In error case increase a new error counter and retry it later.
This behavior avoids buffer errors in the QCA7000, which
results in an unnecessary chip reset including packet loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A stuck ramrod should be deleted from the completion_pending list,
otherwise it will be added again in the future and corrupt the list.
Return error value to inform that ramrod is stuck and should be deleted.
Signed-off-by: Sagiv Ozeri <sagiv.ozeri@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_sp_destroy_request() API was added for SPQ users that need to
free/return the entry they acquired in their error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free the allocated SPQ entry or return the acquired SPQ entry to the free
list in error flows.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_reset_notify_init_enet() only return error early if the return
value of hns3_restore_vlan() is not 0.
This patch adds checking for the return value of hns3_restore_vlan.
Fixes: 7fa6be4fd2 ("net: hns3: fix incorrect return value/type of some functions")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down':
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning:
variable 'ret' set but not used [-Wunused-but-set-variable]
bcmgenet_power_down should return 'ret' instead of 0.
Fixes: ca8cf34190 ("net: bcmgenet: propagate errors from bcmgenet_power_down")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-11-07
This series contains updates to almost all of the Intel wired LAN
drivers.
Lance Roy replaces a spin lock with lockdep_assert_held() for igbvf
driver in move toward trying to remove spin_is_locked().
Colin Ian King fixes a potential null pointer dereference by adding a
check in ixgbe. Also fixed the igc driver by properly assigning the
return error code of a function call, so that we can properly check it.
Shannon Nelson updates the ixgbe driver to not block IPsec offload when
in VEPA mode, in VEB mode, IPsec offload is still blocked because the
device drops packets into a black hole.
Jake adds support for software timestamping for packets sent over
ixgbevf. Also modifies i40e, iavf, igb, igc, and ixgbe to delay calling
skb_tx_timestamp() to the latest point possible, which is just prior to
notifying the hardware of the new Tx packet.
Todd adds the new WoL filter flag so that we properly report that we do
not support this new feature.
YueHaibing from Huawei fixes the igc driver by cleaning up variables
that are not "really" used.
Dan Carpenter cleans up igc whitespace issues.
Miroslav Lichvar fixes e1000e for potential underflow issue in the
timecounter, so modify the driver to use timecounter_cyc2time() to allow
non-monotonic SYSTIM readings.
Sasha provides additional igc cleanups based on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload of geneve decap rules is supported in NFP. Include geneve in the
check for supported types.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the recently added VXLAN and geneve helper functions to
determine the type of the netdev from its rtnl_link_ops.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the MUM/SUC Firmware, UEFI Expansion ROM and MC Status partitions
of the NIC's NVRAM as MTDs if found on the NIC. The first two are needed
in order to properly update them when performing firmware updates; the MC
Status partition is used to determine whether a signed firmware image was
accepted or rejected by a Secure NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN.TCI == 0 is perfectly valid (802.1p), so allow it to be accelerated.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't request tag insertion when it isn't present in outgoing skb.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c: In function 'hclge_log_and_clear_ppp_error':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:821:24: warning:
variable 'reset_level' set but not used [-Wunused-but-set-variable]
enum hnae3_reset_type reset_level = HNAE3_NONE_RESET;
It never used since introduction in commit
01865a50d7 ("net: hns3: Add enable and process hw errors of TM scheduler")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use driver's common notifier for LAG and tunnel configuration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code interested in networking events registers its own notifier
handlers. Create one device-wide notifier instance.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_fl_lag_changels_event() never fails, and therefore we would
never return NOTIFY_BAD for NETDEV_CHANGELOWERSTATE. Make this
clearer by changing nfp_fl_lag_changels_event()'s return type
to void.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning an error from a notifier means we want to veto the change.
We shouldn't veto NETDEV_UNREGISTER just because we couldn't find
the tracking info for given master.
I can't seem to find a way to trigger this unless we have some
other bug, so it's probably not fix-worthy.
While at it move the checking if the netdev really is of interest
into the handling functions, like we do for other events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flower tunnel offloads FW has to be informed about MAC addresses
of tunnel devices. We use a netdev notifier to keep track of these
addresses.
Remove unnecessary loop over netdevices after notifier is registered.
The intention of the loop was to catch devices which already existed
on the system before nfp driver got loaded, but netdev notifier will
replay NETDEV_REGISTER events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6 set flow label and hop limit action offload. Since pedit sets
headers per 4 byte word, we need to ensure that setting either version,
priority, payload_len or nexthdr does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv4 set ttl and tos action offload. Since pedit sets headers per 4
byte word, we need to ensure that setting either version, ihl, protocol,
total length or checksum does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to reallocate the descriptor and remap the
descriptor memory in reset process, otherwise it may cause memory
not freed problem.
Also, this patch initializes the cmd queue's spinlocks in
hclgevf_alloc_cmd_queue, and take the spinlocks when reinitializing
cmd queue' registers.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.
This patch also add some reset related debug log printing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing resetting, roce should do its uninitailization part
before nic's, and do its initialization part after nic's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing PF reset, the driver needs to do some preparatory work
before asserting PF reset. Since when hardware is resetting, it
is necessary to stop tx/rx queue, clear hardware table, etc,
otherwise hardware may run into unrecoverable state if there is
still IO running when the hardware is resetting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a higher level reset, the pending lower level reset
does not have to be processed anymore, because the higher level
reset is the superset of the lower level reset.
Therefore, when processing an higher level reset, the request of
lower level reset needs to be cleared.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hclge is going to reset, it will notify its client with
HNAE3_DOWN_CLIENT, so this client should get into a resetting
status from this moment, other operations from the stack need to
be blocked as well. And when the reset is finished, the client
will be notified with HNAE3_UP_CLIENT, so this is the end of
the resetting status.
This patch uses HNS3_NIC_STATE_RESETTING flag to implement that,
and adds hns3_nic_resetting() to indicate which operation is not
allowed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.
So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.
Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.
So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.
Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.
There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.
So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.
Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC
occurs prior to the initial setup of the local hw_features variable.
This means the features are set as user-changeable, but are not set in
the currently active feature list. This results in the features being
disabled at the driver's initial load.
Move the assignment after the initial assignment of hw_features, and
assign to the local variable. This ensures that NETIF_F_NTUPLE and
NETIF_F_HW_TC are marked as user-changeable, and also enables them by
default when the driver loads.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Address few community comments.
Remove unused code, will be added per demand.
Remove blank lines and unneeded includes.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I just cleaned up a couple small white space issues.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to netif_set_real_num_tx_queues is not assigning the error
return to variable err even though the next line checks err for an
error. Fix this by adding the missing err assignment.
Detected by CoverityScan, CID#1474551 ("Logically dead code")
Fixes: 3df25e4c1e ("igc: Add interrupt support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/igc/igc_main.c: In function 'igc_probe':
drivers/net/ethernet/intel/igc/igc_main.c:3535:11: warning:
variable 'pci_using_dac' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
d89f88419f ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/igc/igc_base.c: In function 'igc_init_phy_params_base':
drivers/net/ethernet/intel/igc/igc_base.c:240:6: warning:
variable 'ctrl_ext' set but not used [-Wunused-but-set-variable]
u32 ctrl_ext;
drivers/net/ethernet/intel/igc/igc_base.c: In function 'igc_get_invariants_base':
drivers/net/ethernet/intel/igc/igc_base.c:290:6: warning:
variable 'link_mode' set but not used [-Wunused-but-set-variable]
u32 link_mode = 0;
It never used since introduction in
commit c0071c7aa5 ("igc: Add HW initialization code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's a new flag for setting WoL filters that is only
enabled on one manufacturer's NICs, and it's not ours. Fail
with EOPNOTSUPP.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the Intel Ethernet drivers call skb_tx_timestamp() earlier than
necessary. Move the calls to this function to the latest point possible,
just prior to notifying hardware of the new Tx packet when we bump the
tail register.
This affects i40e, iavf, igb, igc, and ixgbe.
The e100, e1000, e1000e, fm10k, and ice drivers already call the
skb_tx_timestamp() function just prior to indicating the Tx packet to
hardware, so they do not need to be changed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a call to skb_tx_timestamp in the ixgbevf_tx_map function. This
enables software timestamping for packets sent over this device driver.
The call is placed just prior to when we notify hardware of the new
packet, in order to software timestamp as close as possible to when the
hardware will transmit.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When it's possible that the PF might end up trying to send a
packet to one of its own VFs, we have to forbid IPsec offload
because the device drops the packets into a black hole.
See commit 47b6f50077 ("ixgbe: disallow IPsec Tx offload
when in SR-IOV mode") for more info.
This really is only necessary when the device is in the default
VEB mode. If instead the device is running in VEPA mode,
the packets will go through the encryption engine and out the
MAC/PHY as normal, and get "hairpinned" as needed by the switch.
So let's not block IPsec offload when in VEPA mode. To get
there with the ixgbe device, use the handy 'bridge' command:
bridge link set dev eth1 hwmode vepa
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an earlier check to see if xdp_ring is null when configuring
the tx ring, so assuming that it can still be null, the clearing of
the xdp_ring->state currently could end up with a null pointer
dereference. Fix this by only clearing the bit if xdp_ring is not null.
Detected by CoverityScan, CID#1473795 ("Dereference after null check")
Fixes: 024aa5800f ("ixgbe: added Rx/Tx ring disable/enable functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit bacd75cfac ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df395 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.
Fix this by changing req_speeds to be u16.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Binding and unbinding the switch driver which creates the DSA slave
network devices for which we set-up inspection would lead to
undesireable effects since we were not clearing the port/queue mapping
to the SYSTEMPORT TX queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9de ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.
Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.
Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);
An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.
In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.
In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.
The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.
This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.
This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:
ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1
The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.
Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print should say "Enabling" instead of "Enaabling"
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the spec, whenever insert PVID field is set, the VLAN
driver insertion mode should be set to 01b which isn't done currently.
Fix it.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The remove path does not currently check to see if a
reset is in progress before proceeding. This can cause
a resource collision resulting in various types of errors.
Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
alx_drv_name is not used outside main.c, so there's no reason for it to
have external linkage.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-10-31
This series contains a various collection of fixes.
Miroslav Lichvar from Red Hat or should I say IBM now? Updates the PHC
timecounter interval for igb so that it gets updated at least once
every 550 seconds.
Ngai-Mint provides a fix for fm10k to prevent a soft lockup or system
crash by adding a new condition to determine if the SM mailbox is in the
correct state before proceeding.
Jake provides several fm10k fixes, first one marks complier aborts as
non-fatal since on some platforms trigger machine check errors when the
compile aborts. Added missing device ids to the in-kernel driver. Due
to the recent fixes, bumped the driver version.
I (Jeff Kirsher) fixed a XFRM_ALGO dependency for both ixgbe and
ixgbevf. This fix was based on the original work from Arnd Bergmann,
which only fixed ixgbe.
Mitch provides a fix for i40e/avf to update the status codes, which
resolves an issue between a mis-match between i40e and the iavf driver,
which also supports the ice LAN driver.
Radoslaw fixes the ixgbe where the driver is logging a message about
spoofed packets detected when the VF is re-started with a different MAC
address.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An MC-aware mode was introduced in commit 7b81953066 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"). In MC-aware mode,
BUM traffic gets a special treatment by being assigned to a separate set
of traffic classes 8..15. Pairs of TCs 0 and 8, 1 and 9, etc., are then
configured to strictly prioritize the lower-numbered ones. The intention
is to prevent BUM traffic from flooding the switch and push out all UC
traffic, which would otherwise happen, and instead give UC traffic
precedence.
However strictly prioritizing UC traffic has the effect that UC overload
pushes out all BUM traffic, such as legitimate ARP queries. These
packets are kept in queues for a while, but under sustained UC overload,
their lifetime eventually expires and these packets are dropped. That is
detrimental to network performance as well.
Therefore configure the MC TCs (8..15) with minimum shaper of 200Mbps (a
minimum permitted value) to allow a trickle of necessary control traffic
to get through.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add QEEC.mise (minimum shaper enable) and QEEC.min_shaper_rate to enable
configuration of minimum shaper.
Increase the QEEC length to 0x20 as well: that's the length that the
register has had for a long time now, but with the configurations that
mlxsw typically exercises, the firmware tolerated 0x1C-sized packets.
With mise=true however, FW rejects packets unless they have the full
required length.
Fixes: b9b7cee405 ("mlxsw: reg: Add QoS ETS Element Configuration register")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes: 6d4fab3953 ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some functions that, when they fail to send the command,
need to return the corresponding error value to its caller.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: 681ec3999b ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.
Fixes: b50ae26c57 ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes: 3efb960f05 ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.
Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.
Fixes: cd8c5c269b ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As shown by Dmitris, we need to use csum_block_add() instead of csum_add()
when adding the FCS contribution to skb csum.
Before 4.18 (more exactly commit 88078d98d1 "net: pskb_trim_rcsum()
and CHECKSUM_COMPLETE are friends"), the whole skb csum was thrown away,
so RXFCS changes were ignored.
Then before commit d55bef5059 ("net: fix pskb_trim_rcsum_slow() with
odd trim offset") both mlx5 and pskb_trim_rcsum_slow() bugs were canceling
each other.
Now we fixed pskb_trim_rcsum_slow() we need to fix mlx5.
Note that this patch also rewrites mlx5e_get_fcs() to :
- Use skb_header_pointer() instead of reinventing it.
- Use __get_unaligned_cpu32() to avoid possible non aligned accesses
as Dmitris pointed out.
Fixes: 902a545904 ("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
Reported-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Dimitris Michailidis <dmichail@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Paweł Staszewski <pstaszewski@itcare.pl>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Tested-By: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original work from Arnd Bergmann.
When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'
Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:
A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes: eda0333ac2 ("ixgbe: add VF IPsec management")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mvpp2 driver has the curious behaviour of passing a stack variable
to irq_set_affinity_hint(), which results in the kernel exploding
the first time anyone accesses this information. News flash: userspace
does, and irqbalance will happily take the machine down. Great stuff.
An easy fix is to track the mask within the queue_vector structure,
and to make sure it has the same lifetime as the interrupt itself.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abdul Haleem reported a build error on ppc :
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: `struct
iphdr` declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is
only this definition or declaration, which is probably not what you want
[enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function
get_fixed_ipv4_csum:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing
pointer to incomplete type
__u8 ipproto = iph->protocol;
^
Fixes: 55469bc6b5 ("drivers: net: remove <net/busy_poll.h> inclusion when not needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a failed reload, the driver is still registered to devlink, its
devlink instance is still allocated and the 'reload_fail' flag is set.
Then, in the next reload try, the driver's allocated devlink instance will
be freed without unregistering from devlink and its components (e.g,
resources). This scenario can cause a use-after-free if the user tries to
execute command via devlink user-space tool.
Fix by not freeing the devlink instance during reload (failed or not).
Fixes: 24cc68ad6c ("mlxsw: core: Add support for reload")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Demands to remove FDB entries should be honored even if the FDB entry in
question was originally learned, and not added by the user. Therefore
ignore the added_by_user datum for SWITCHDEV_FDB_DEL_TO_DEVICE.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/huawei/hinic/hinic_tx.c:392:34: error: implicit
conversion from enumeration type 'enum hinic_l4_tunnel_type' to
different enumeration type 'enum hinic_l4_offload_type'
[-Werror,-Wenum-conversion]
hinic_task_set_tunnel_l4(task, TUNNEL_UDP_NO_CSUM,
~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~
1 error generated.
It seems that hinic_task_set_tunnel_l4 was meant to take an enum of type
hinic_l4_tunnel_type, not hinic_l4_offload_type, given both the name of
the functions and the values used.
Fixes: cc18a7543d ("net-next/hinic: add checksum offload and TSO support")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"What better way to start off a weekend than with some networking bug
fixes:
1) net namespace leak in dump filtering code of ipv4 and ipv6, fixed
by David Ahern and Bjørn Mork.
2) Handle bad checksums from hardware when using CHECKSUM_COMPLETE
properly in UDP, from Sean Tranchetti.
3) Remove TCA_OPTIONS from policy validation, it turns out we don't
consistently use nested attributes for this across all packet
schedulers. From David Ahern.
4) Fix SKB corruption in cadence driver, from Tristram Ha.
5) Fix broken WoL handling in r8169 driver, from Heiner Kallweit.
6) Fix OOPS in pneigh_dump_table(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
net/neigh: fix NULL deref in pneigh_dump_table()
net: allow traceroute with a specified interface in a vrf
bridge: do not add port to router list when receives query with source 0.0.0.0
net/smc: fix smc_buf_unuse to use the lgr pointer
ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are called
net/{ipv4,ipv6}: Do not put target net if input nsid is invalid
lan743x: Remove SPI dependency from Microchip group.
drivers: net: remove <net/busy_poll.h> inclusion when not needed
net: phy: genphy_10g_driver: Avoid NULL pointer dereference
r8169: fix broken Wake-on-LAN from S5 (poweroff)
octeontx2-af: Use GFP_ATOMIC under spin lock
net: ethernet: cadence: fix socket buffer corruption problem
net/ipv6: Allow onlink routes to have a device mismatch if it is the default route
net: sched: Remove TCA_OPTIONS from policy
ice: Poll for link status change
ice: Allocate VF interrupts and set queue map
ice: Introduce ice_dev_onetime_setup
net: hns3: Fix for warning uninitialized symbol hw_err_lst3
octeontx2-af: Copy the right amount of memory
net: udp: fix handling of CHECKSUM_COMPLETE packets
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAlvTKWYQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw8J5EACMAnrTxWQmXfQXOZEVxztcFavH6LP8mh2e
7FZIZ38jzHXXvl81tAg1nBhzFUU/qtvqW8NDCZ9OBxKvp6PFDNhWu241ZodSB1Kw
MZWy2A9QC+qbHYCC+SB5gOT0+Py3v7LNCBa5/TxhbFd35THJM8X0FP7gmcCGX593
9Ml1rqawT4mK5XmCpczT0cXxyC4TgVtpfDWZH2KgJTR/kwXVQlOQOGZ8a1y/wrt7
8TLIe7Qy4SFRzjhwbSta1PUehyYfe4uTSsXIJ84kMvNMxinLXQtvd7t9TfsK8p/R
WjYUneJskVjtxVrMQfdV4MxyFL1YEt2mYcr0PMKIWxMCgGDAZsHPoUZmjyh/PrCI
uiZtEHn3fXpUZAV/xEHHNirJxYyQfHGiksAT+lPrUXYYLCcZ3ZmqiTEYhGoQAfH5
CQPMuxA6yXxp6bov6zJwZSTZtkXciju8aQRhUhlxIfHTqezmGYeql/bnWd+InNuR
upANLZBh6D2jTWzDyobconkCCLlVkSqDoqOx725mMl6hIcdH9d2jVX7hwRf077VI
5i3CyPSJOkSOLSdB8bAPYfBoaDtH2bthxieUrkkSbIjbwHO1H6a2lxPeG/zah0a3
ePMGhi7J84UM4VpJEi000cP+bhPumJtJrG7zxP7ldXdfAF436sQ6KRptlcpLpj5i
IwMhUQNH+g==
=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
The SPI dependency does not apply to lan743x driver, and other
drivers in the group already state their dependence on SPI.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using generic NAPI interface no longer need to include
<net/busy_poll.h>, since busy polling was moved to core networking
stack long ago.
See commit 79e7fff47b ("net: remove support for per driver
ndo_busy_poll()") for reference.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that WoL from S5 is broken (WoL from S3 works) and the
analysis showed that during system shutdown the network interface was
brought down already when the actual kernel shutdown started.
Therefore netif_running() returned false and as a consequence the PHY
was suspended. Obviously WoL wasn't working then.
To fix this the original patch needs to be effectively reverted.
A side effect is that when normally bringing down the interface and
WoL is enabled the PHY will remain powered on (like it was before the
original patch).
Fixes: fe87bef01f ("r8169: don't check WoL when powering down PHY and interface is down")
Reported-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function nix_update_mce_list() is called from
nix_update_bcast_mce_list(), and a spin lock is held
here, so we should use GFP_ATOMIC instead.
Fixes: 4b05528ebf ("octeontx2-af: Update bcast list upon NIXLF alloc/free")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket buffer is not re-created when headroom is 2 and tailroom is 1.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-10-24
This series contains fixes for the ice driver.
Anirudh fixes a namespace issue which was introduced with a previous
patch to remove ice_netpoll. Fixed up the device ID define names to
align with the branding string names. Use the capability count returned
by the firmware, instead of calculating the count. Introduced driver
workarounds due to current firmware limitations. Fixed the queue
mapping for a VF, which needs to be set in the config and scatter queue
modes. Fixed the driver which is setup to handle link status events
(LSE), even though the firmware does not have this feature yet, so add
the ability to poll for link status changes while we wait for updated
firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.
For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate VF interrupts using VPINT_ALLOC_PCI. Multiple interrupts are
specified as a range from "first" to "last".
Also, according to the spec, the queue mapping for a VF needs to be set
in both contig and scatter queue modes. So make this change as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains a couple of driver workarounds for current
firmware limitations. These workarounds are expected to go away once
these limitations are fixed in the firmware.
On a firmware release that has these issues addressed, these workarounds
(while unnecessary) will not break anything.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the smatch warning,
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:700
hclge_log_and_clear_ppp_error() error: uninitialized symbol
'hw_err_lst3'
Link: https://lkml.org/lkml/2018/10/23/430
Fixes: da2d072a9e ("net: hns3: Add enable and process hw errors from PPP")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy and paste bug where we copied the sizeof() from the chunk
before. We're copying more data than intended but the destination is a
union so it doesn't cause memory corruption.
Fixes: ffb0abd7e9 ("octeontx2-af: NIX AQ instruction enqueue support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware now returns the capability count in the command buffer.
Use it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update to the current firmware major and minor version which are
1 and 3 respectively.
Also remove an empty comment line.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Basically remove references to C810 and use E810C (from the branding
string) instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 158a08a694 ("ice: remove ndo_poll_controller") removed
ice_netpoll and introduced a namespace warning for ice_msix_clean_rings.
Fix the namespace warning by making ice_msix_clean_rings static.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new of_get_compatible_child() helper to lookup the mdio-internal
child node instead of using of_find_compatible_node(), which searches
the entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the mdio-mux node). Fortunately, this was inadvertently
balanced by a failure to drop the mdio-mux reference after lookup.
While at it, also fix the related mdio-internal- and phy-node reference
leaks.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the new of_get_compatible_child() helper to lookup the mdio child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Static Checker Warnings:
drivers/net/ethernet/qlogic/qed/qed_main.c:1510 qed_fill_link_capability()
error: uninitialized symbol 'tcvr_state'.
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1951 qed_mcp_trans_speed_mask()
error: uninitialized symbol 'transceiver_state'.
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1951 qed_mcp_trans_speed_mask()
error: uninitialized symbol 'transceiver_type'.
Symbols tcvr_state, transceiver_state and transceiver_type
are initialized with respective default state.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mentioned commit needs to be reverted because we cannot pass
string allocated on stack to request_irq(). This function stores
uses this pointer for later use (e.g. /proc/interrupts) so we need
to keep this string persistently.
Fixes: d6d9704af8 ("be2net: remove desc field from be_eq_obj")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We observed that packets and bytes count are not reset
when user performs interface down. Eventually, tx queue is
exhausted and packets will not be sent out.
To avoid this problem, resets tx queue in ndo_stop.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a compatibility issue between RTL8211E implemented
in Developerbox and netsec ethernet controller IP.
Our MDIO controller stops MDC clock right after the write
access, but RTL8211E expects MDC clock must be kept toggling
for several clock cycle with MDIO high before entering
the IDLE state. Without keeping clock after write access,
write access is not correctly handled and register is not
updated.
To meet this requirement, netsec driver needs to issue dummy
read(e.g. read PHYID1(offset 0x2) register) right after write
access, to keep MDC clock.
We think this compatibility issue is a problem specific to
our MDIO controller and RTL8211E.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ndo_stop, driver resets the netsec ethernet controller IP.
When the netsec IP is reset, HW running mode turns to NRM mode
and driver has to wait until this mode transition completes.
But mode transition to NRM will not complete if the PHY is
in normal operation state. Netsec IP requires PHY is in
power down state when it is reset.
This modification stops the PHY before resetting netsec.
Together with this modification, phy_addr is stored in netsec_priv
structure because ndev->phydev is not yet ready in ndo_init.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Yoshitoyo Osaki <osaki.yoshitoyo@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After flushing all mcast entries from the table, the ones contained in
mc list of ndev are not restored when promisc mode is toggled off,
because they are considered as synched with ALE, thus, in order to
restore them after promisc mode - reset syncing info. This fix
touches only switch mode devices, including single port boards
like Beagle Bone.
Fixes: commit 5da1948969
("net: ethernet: ti: cpsw: fix lost of mcast packets while rx_mode update")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default NIXLF is set in UCAST mode. This patch adds a new
mailbox message which when sent by a RVU PF changes this default
mode. When promiscuous mode is needed, the reserved promisc entry
for each of RVU PF is setup to match against ingress channel number
only, so that all pkts on that channel are accepted and forwarded
to the mode change requesting PF_FUNC's NIXLF.
PROMISC and ALLMULTI modes are supported only for PFs, for VFs only
UCAST mode is supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new mailbox message for a PF/VF to set/update
it's NIXLF's MAC address. Also updates unicast NPC
MCAM entry with this address as matching DMAC.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to change
NIX Rx flowkey algorithm index in NPC RX RSS_ACTION.
eg: a ethtool command changing RSS algorithm for a netdev
interface would trigger this change in NPC.
If PF/VF doesn't specify any MCAM entry index then default
UCAST entry of the NIXLF attached to PF/VF will be updated
with RSS_ACTION and flowkey index.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure NIX RX flowkey algorithm configuration to support
RSS (receive side scaling). Currently support for only L3/L4
2-tuple and 4-tuple hash of IPv4/v6/TCP/UDP/SCTP is added.
HW supports upto 32 different flowkey algorithms which SW
can define, this patch defines 9. NPC RX ACTION has to point
to one of these flowkey indices for RSS to work.
The configuration is dependent on NPC parse result's layer
info. So if NPC KPU profile changes suchthat LID/LTYPE values
of above said protocols change then this configuration will
most likely be effected.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon NIXLF_ALLOC install a unicast forwarding rule in NPC MCAM
like below
- Match pkt DMAC with NIXLF attached PF/VF's MAC address.
- Ingress channel
- Action is UCAST
- Forward to PF_FUNC of this NIXLF
And broadcast pkt forwarding rule as
- Match L2B bit in MCAM search key
- Ingress channel
- Action is UCAST, for now, later it will be changed to MCAST.
Only PFs can install this rule
Upon NIXLF_FREE disable all MCAM entries in use by that NIXLF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LMAC channel info like Rx/Tx channel base and count to
NIXLF_ALLOC mailbox message response. This info is used by
NIXLF attached RVU PF/VF to configure SQ's default channel,
TL3_TL2_LINKX_CFG and to install MCAM rules in NPC based
on matching ingress channel number.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some minimal configuration for NPC MCAM and
LDATA extraction which is sufficient enough to install
ucast/bcast/promiscuous forwarding rules. Below is the
config done
- LDATA extraction config to extract DMAC from pkt
to offset 64bit in MCAM search key.
- Set MCAM lookup keysize to 224bits
- Set MCAM TX miss action to UCAST_DEFAULT
- Set MCAM RX miss action to DROP
Also inorder to have guaranteed space in MCAM to install
ucast forwarding rule for each of RVU PF/VF, reserved
one MCAM entry for each of NIXLF for ucast rule. And two
entries for each of RVU PF. One for bcast pkt replication
and other for promiscuous mode which allows all pkts
received on a HW CGX/LBK channel.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Config NPC layer info from KPU profile into protocol
checker to identify outer L2/IPv4/TCP/UDP headers in a
packet. And enable IPv4 checksum validation.
L3/L4 and L4 CSUM validation will be enabled by PF/VF
drivers by configuring NIX_AF_LF(0..127)_RX_CFG via mbox
i.e 'nix_lf_alloc_req->rx_cfg'
Also enable setting of NPC_RESULT_S[L2B] when an outer
L2 broadcast address is detected. This will help in
installing NPC MCAM rules for broadcast packets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for PF/VF drivers to configure NIX to
capture and/or strip VLAN tag from ingress packets.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon NIXLF ALLOC/FREE, add or remove corresponding PF_FUNC from
the broadcast packet replication list of the CGX LMAC mapped
RVU PF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate memory for mcast/bcast/mirror replication entry
contexts, replication buffers (used by HW) and config HW
with corresponding memory bases. Added support for installing
MCEs via NIX AQ mbox.
For now support is restricted to broadcast pkt replication,
hence MCE table size and number of replication buffers
allocated are less. Each CGX LMAC mapped RVU PF is assigned
a MCE table of size 'num VFs of that PF + PF'.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures all 16 KPUs and iKPU (pkinds) with
the KPU parser profile defined in npc_profile.h. Each KPU
engine has a 128 entry CAM, only CAM entries which are listed
in the profile are enabled and rest are left disabled.
Also
- Memory is allocated for pkind's bitmap and PFFUNC, interface
channel mapping.
- Added all CSR offsets of NPC HW block.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPC block is responsible for parsing and forwarding
packets to different NIXLFs. NPC has 16 KPU engines
(Kangaroo parse engine) and one iKPU which represents
pkinds. Each physical port either CGX/LBK is assigned
a pkind and upon receiving a packet HW takes that port's
pkind and starts parsing as per the KPU engines config.
This patch adds header files which contain configuration
profile/array for each of the iKPU and 16 KPU engines.
Signed-off-by: Hao Zheng <hao.zheng@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new mailbox message to reset
a NIXLF's receive and transmit HW stats.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a PF/VF driver to configure
NIX transmit scheduler queues via mbox. Since PF/VF doesn't
know the absolute HW index of the NIXLF attached to it, AF
traps the register config and overwrites with the correct
NIXLF index.
HW supports shaping, colouring and policing of packets with
these multilevel traffic scheduler queues. Instead of
introducing different mbox message formats for different
configurations and making both AF & PF/VF driver implementation
cumbersome, access to the scheduler queue's CSRs is provided
via mbox. AF checks whether the sender PF/VF has the
corresponding queue allocated or not and dumps the config
to HW. With a single mbox msg 20 registers can be configured.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a PF/VF to allocate or free NIX transmit
scheduler queues via mbox. For setting up pkt transmission
priorities between queues, the scheduler queues have to be
contiguous w.r.t their HW indices. So both contiguous and
non-contiguous allocations are supported.
Upon receiving NIX_TXSCH_FREE mbox msg all scheduler queues
allocated to sending PFFUNC (PF/VF) will be freed. Selective
free is not supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux/prefetch.h is never explicitly included in ena_com, although
functions from it, such as prefetchw(), are used throughout ena_com.
This is an inclusion bug, and we fix it here by explicitly including
linux/prefetch.h. The bug was exposed when the driver was compiled
for the xtensa architecture.
Fixes: 689b2bdaaa ("net: ena: add functions for handling Low Latency Queues in ena_com")
Fixes: 8c590f9776 ("ena: Fix Kconfig dependency on X86")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB_MAX_CHAIN is three. We wanted to allocate enough memory to hold four
structs but there are missing parentheses so we only allocate enough
memory for three structs and the first byte of the fourth one.
Fixes: 328edb499f ("net/mlx5: Split FDB fast path prio to multiple namespaces")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are supposed to return one on failure and zero on
success. Returning a zero here could cause uninitialized variable
bugs in several of the callers. For example:
drivers/scsi/cxgbi/cxgb4i/cxgb4i.c:1660 get_iscsi_dcb_priority()
error: uninitialized symbol 'caps'.
Fixes: 48365e4852 ("qlcnic: dcb: Add support for CEE Netlink interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables and process hw errors of TM scheduler and
QCN(Quantized Congestion Control).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables and process hw errors from the
PPP(Programmable Packet Process) block.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds enable and processing of hw errors from IGU(Ingress Unit),
EGU(Egress Unit) and NCSI(Network Controller Sideband Interface).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds enable and processing of ecc errors from
common HNS blocks, CMDQ(Command Queue),
IMP(Integrated Management Processor) and TQP(Task Queue Pair).
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functions to enable and disable hw errors.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery for the HNS hw errors.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set of hw errors occurred in the HNS3 are reported to the
hns3 driver through PCIe AER and RAS.The error info will be
processed and appropriately recovered.
This patch adds error_detected callback and error processing.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_detach_rsrcs':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:855:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:853:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c: In function 'rvu_mbox_handler_ATTACH_RESOURCES':
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1054:7: warning:
variable 'is_pf' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1053:6: warning:
variable 'devnum' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
746ea74241 ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c: In function 'rvu_npa_init':
drivers/net/ethernet/marvell/octeontx2/af/rvu_npa.c:446:20: warning:
variable 'block' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit 7a37245ef2 ("octeontx2-af: NPA block admin queue init")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Implement two new kind of BPF maps, that is, queue and stack
map along with new peek, push and pop operations, from Mauricio.
2) Add support for MSG_PEEK flag when redirecting into an ingress
psock sk_msg queue, and add a new helper bpf_msg_push_data() for
insert data into the message, from John.
3) Allow for BPF programs of type BPF_PROG_TYPE_CGROUP_SKB to use
direct packet access for __skb_buff, from Song.
4) Use more lightweight barriers for walking perf ring buffer for
libbpf and perf tool as well. Also, various fixes and improvements
from verifier side, from Daniel.
5) Add per-symbol visibility for DSO in libbpf and hide by default
global symbols such as netlink related functions, from Andrey.
6) Two improvements to nfp's BPF offload to check vNIC capabilities
in case prog is shared with multiple vNICs and to protect against
mis-initializing atomic counters, from Jakub.
7) Fix for bpftool to use 4 context mode for the nfp disassembler,
also from Jakub.
8) Fix a return value comparison in test_libbpf.sh and add several
bpftool improvements in bash completion, documentation of bpf fs
restrictions and batch mode summary print, from Quentin.
9) Fix a file resource leak in BPF selftest's load_kallsyms()
helper, from Peng.
10) Fix an unused variable warning in map_lookup_and_delete_elem(),
from Alexei.
11) Fix bpf_skb_adjust_room() signature in BPF UAPI helper doc,
from Nicolas.
12) Add missing executables to .gitignore in BPF selftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically a resubmit of 1e91887685 ("r8169: add support
for Byte Queue Limits") which was reverted later. The problems causing
the revert seem to have been fixed in the meantime.
Only change to the original patch is that the call to
netdev_reset_queue was moved to rtl8169_tx_clear.
The Tested-by refers to a system using the RTL8168evl chip version.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a separate "slow event" handler isn't needed because all
interrupt events trigger asynchronous activity. And in case of SYSErr
we have bigger problems than performance anyway.
This patch also allows to get rid of acking interrupt events in the
NAPI poll callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial non-functional change added to simplify getting multiple
references to device pointer in lpc_eth_drv_probe().
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A trivial change which removes an unused local variable, the issue
is reported as a compile time warning:
drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_eth_drv_probe':
drivers/net/ethernet/nxp/lpc_eth.c:1250:21: warning: variable 'phydev' set but not used [-Wunused-but-set-variable]
struct phy_device *phydev;
^~~~~~
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC controller device is available on NXP LPC32xx platform only,
and the LPC32xx platform supports OF builds only, so additional
checks in the device driver are not needed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change removes all unnecessary included headers from the driver
source code, the remaining list is sorted in alphabetical order.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have the 'struct rocker_desc_info *desc_info'
variable static since new value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides misc updates to mlx5 core and netdevice driver.
1) From Tariq Toukan: Refactor fragmented buffer struct fields and init flow.
2) From Vlad Buslov, Flow counters cache improvements and fixes follow up.
as a follow up work for the previous series of the mlx5 flow counters,
Vlad provides two fixes:
2.1) Take fs_counters dellist before addlist
Fixes: 6e5e228391 ("net/mlx5: Add new list to store deleted flow counters")
2.2) Remove counter from idr after removing it from list
Fixes: 12d6066c3b ("net/mlx5: Add flow counters idr")
From Shay Agroskin,
3) Add FEC set/get FW commands and FEC ethtool callbacks support
4) Add new ethtool statistics to cover errors on rx, such as FEC errors.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbyO6dAAoJEEg/ir3gV/o+nqIIAJP9ETql9EnCVQiuG/OwWXNM
fPV5iBeubquGtTRlUIL3ww6N1ab+wtYPIqd4CEMiG2a5NSDrNWjPQJ+D6P+3kGOV
51V+pgzPRGkWzHijzRb96Fgr3nYXjpRgJDzesASAYv8Du201aFNP6yjEdjET1ZDO
maIHQHtENU7Pwb3Rg47ILAdImsd4eqm630au9pUv5GtWTe9l+Z3a1LOpWAftWCjV
eRZv/CcCCickOTFTWBn2HGHTh8qC+FN0YY0NZYgqSizjdOdW7KyEqoTqKVvANJ1G
N01z9hDPyLNJ010+zprFjNBz52fBYK6eMHLP+dzq0qYw924EryeuMgdOMnS6gig=
=LD4j
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-10-18
This series provides misc updates to mlx5 core and netdevice driver.
1) From Tariq Toukan: Refactor fragmented buffer struct fields and init flow.
2) From Vlad Buslov, Flow counters cache improvements and fixes follow up.
as a follow up work for the previous series of the mlx5 flow counters,
Vlad provides two fixes:
2.1) Take fs_counters dellist before addlist
Fixes: 6e5e228391 ("net/mlx5: Add new list to store deleted flow counters")
2.2) Remove counter from idr after removing it from list
Fixes: 12d6066c3b ("net/mlx5: Add flow counters idr")
From Shay Agroskin,
3) Add FEC set/get FW commands and FEC ethtool callbacks support
4) Add new ethtool statistics to cover errors on rx, such as FEC errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checksum offload and TSO support for the HiNIC
driver. Perfomance test (Iperf) shows more than 100% improvement
in TCP streams.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On multi adapter setup if the uld registration fails even on
one adapter, the allocated resources for the uld on all the
adapters are freed, rendering the functioning adapters unusable.
This commit fixes the issue by freeing the allocated resources
only for the failed adapter.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct type was copied from the line before but it should be "tx"
instead of "rx". I have reviewed the code and I can't immediately see
that this bug causes a runtime issue.
Fixes: 36e53349b6 ("bnxt_en: Add additional extended port statistics.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are counters for errors received on rx side, such as
FEC errors.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver callback function for 'ethtool --show-fec',
'ethtool --set-fec' commands.
The query function returns active and configured FEC policy
for current link speed.
The set function sets FEC policy for all supported link
speeds.
1) If current link speed doesn't support requested FEC policy,
the function fails.
2) If a different link speed doesn't support requested FEC
policy, FEC capbilities for this speed are turned off.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added functions to query and set link FEC policy.
To get/set FEC capabilities in PPLM reg we need to query
current link speed.
'mlx5_get_fec_speed_field' queries current link speed and returns
correct field offset.
FEC Query's return value is divided into 'active FEC policy', which is
the FEC policy used by the link, and 'configured FEC policy', which
is the FEC policy requested by the user.
The two values may differ if:
1) FEC policy was configured to 'auto',
in which case the active FEC policy would be the default FEC policy
for current link speed.
2) FEC policy was changed, but no link reset is performed. In which case,
the active FEC policy would become the configured one after a link
reset.
FEC set function sets FEC policy for all link speeds and perform link
reset.
1) If current link speed doesn't support requested FEC policy,
the function fails.
2) If a different link speed doesn't support requested FEC policy,
FEC capbilities for this speed are turned off and a warning message
is printed.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fs_counters list can temporary become unsorted when new counters are
created/deleted concurrently. Idr is used to quickly lookup position to
insert new counter in logarithmic time. However, if new flows are
concurrently inserted during time window when flows with adjacent ids are
already removed from idr but are still present in counters list,
mlx5_fc_stats_work() observes counters list in inconsistent state, which
results following warning:
[ 1839.561955] mlx5_core 0000:81:00.0: mlx5_cmd_fc_bulk_get:587:(pid 729): Flow counter id (0x102d5) out of range (0x1c0a8..0x1c10b). Counter ignored.
Move idr_remove() call to be executed synchronously with counter deletion
from list. Extract this code to mlx5_fc_stats_remove() helper function that
is called by workqueue job handler mlx5_fc_stats_work().
Fixes: 12d6066c3b ("net/mlx5: Add flow counters idr")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
In fs_counters elements from both addlist and dellist are removed by
mlx5_fc_stats_work() without any locking. This introduces race condition
when batch of new rules is created and then immediately deleted (for
example, when error occurred during flow creation). In such case some of
the rules might be in dellist, but not in addlist when mlx5_fc_stats_work()
is executed concurrently with tc, which will result rule deletion and
use-after-free on next iteration because deleted rules are still in
addlist.
Always take dellist first to guarantee that rules can only be deleted after
they were removed from addlist.
Fixes: 6e5e228391 ("net/mlx5: Add new list to store deleted flow counters")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reported-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Take struct mlx5_frag_buf out of mlx5_frag_buf_ctrl, as it is not
needed to manage and control the datapath of the fragmented buffers API.
struct mlx5_frag_buf contains control info to manage the allocation
and de-allocation of the fragmented buffer.
Its fields are not relevant for datapath, so here I take them out of the
struct mlx5_frag_buf_ctrl, except for the fragments array itself.
In addition, modified mlx5_fill_fbc to initialise the frags pointers
as well. This implies that the buffer must be allocated before the
function is called.
A set of type-specific *_get_byte_size() functions are replaced by
a generic one.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now that the documents have been updated to conform to the reStructured Text
guidelines, we can now change the file extensions and update the other
related references.
This converts all of the Intel wired LAN driver documentation to *.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Added the fm10k kernel documentation, which apparently was missing.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e ("r8169: remove work from irq handler.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2018-10-17
This series adds support for the new igc driver.
The igc driver is the new client driver supporting the Intel I225
Ethernet Controller, which supports 2.5GbE speeds. The reason for
creating a new client driver, instead of adding support for the new
device in e1000e, is that the silicon behaves more like devices
supported in igb driver. It also did not make sense to add a client
part, to the igb driver which supports only 1GbE server parts.
This initial set of patches is designed for basic support (i.e. link and
pass traffic). Follow-on patch series will add more advanced support
like VLAN, Wake-on-LAN, etc..
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
========================================================================
From Or Gerlitz <ogerlitz@mellanox.com>:
This series from Paul adds support to mlx5 e-switch tc offloading of multiple priorities and chains.
This is made of four building blocks (along with few minor driver refactors):
[1] Split FDB fast path prio to multiple namespaces
Currently the FDB name-space contains two priorities, fast path (p0) and slow path (p1).
The slow path contains the per representor SQ send-to-vport TX rule and the match-all
RX miss rule. As a pre-step to support multi-chains and priorities, we split the FDB fast path
to multiple namespaces (sub namespaces), each with multiple priorities.
[2] E-Switch chains and priorities
A chain is a group of priorities. We use the fdb parallel sub-namespaces to implement chains,
and a flow table for each priority in them.
Because these namespaces are parallel and in series to the slow path
fdb, the chains aren't connected to each other (but to the slow path),
and one must use a explicit goto action to reach a different chain.
Flow tables for the priorities are created on demand and destroyed
once not used.
[3] Add a no-append flow insertion mode, use it for TC offloads
Enhance the driver fs core, such that if a no-append flag is set by the caller,
we add a new FTE, instead of appending the actions of the inserted rule when
the same match already exists.
For encap rules, we defer the HW offloading till we have a valid neighbor. This can
result in the packet hitting a lower priority rule in the HW DP. Use the no-append API
to push these packets to the slow path FDB table, so they go to the TC kernel DP as done
before priorities where supported.
[4] Offloading tc priorities and chains for eswitch flows
Using [1], [2] and [3] above we add the support for offloading both chains
and priorities. To get to a new chain, use the tc goto action. We support
a fixed prio range 1-16, and chains 0-3.
=============================================================================
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbx6k1AAoJEEg/ir3gV/o+l40H/14rNaV27vefjuALgOvNX4DY
iSI5UFv9ILnAemcD2xkVfJeGolwdzoRhCXJ5oyCylCPnP4tb9zgDgwu9V/WmIRG+
DOaPLu+0V6jqfEGO5sXJPMhJNUR8WWAjfu66htJ0Nc1HV2OM5eYrcvjaYCfW4Egr
QFWGyq4sPyYcpbb7wURbhmkfs8Vwxcj9c2cZIfXo3VJsKxULqU9Mj5hZnirI1OAy
UhjLssb/8wfHmwNcqETI9ae7O+vPDMLkxdQvpviEBI+HJ7vZ6op2X4lVEsn/Bx2E
/KrHGQObkwim8thTOYkQeJtqptWbiRvkpNnwryUV1fwjWPl6X1r3bXH7RdeRwCg=
=aFCc
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2018-10-17
========================================================================
From Or Gerlitz <ogerlitz@mellanox.com>:
This series from Paul adds support to mlx5 e-switch tc offloading of multiple priorities and chains.
This is made of four building blocks (along with few minor driver refactors):
[1] Split FDB fast path prio to multiple namespaces
Currently the FDB name-space contains two priorities, fast path (p0) and slow path (p1).
The slow path contains the per representor SQ send-to-vport TX rule and the match-all
RX miss rule. As a pre-step to support multi-chains and priorities, we split the FDB fast path
to multiple namespaces (sub namespaces), each with multiple priorities.
[2] E-Switch chains and priorities
A chain is a group of priorities. We use the fdb parallel sub-namespaces to implement chains,
and a flow table for each priority in them.
Because these namespaces are parallel and in series to the slow path
fdb, the chains aren't connected to each other (but to the slow path),
and one must use a explicit goto action to reach a different chain.
Flow tables for the priorities are created on demand and destroyed
once not used.
[3] Add a no-append flow insertion mode, use it for TC offloads
Enhance the driver fs core, such that if a no-append flag is set by the caller,
we add a new FTE, instead of appending the actions of the inserted rule when
the same match already exists.
For encap rules, we defer the HW offloading till we have a valid neighbor. This can
result in the packet hitting a lower priority rule in the HW DP. Use the no-append API
to push these packets to the slow path FDB table, so they go to the TC kernel DP as done
before priorities where supported.
[4] Offloading tc priorities and chains for eswitch flows
Using [1], [2] and [3] above we add the support for offloading both chains
and priorities. To get to a new chain, use the tc goto action. We support
a fixed prio range 1-16, and chains 0-3.
=============================================================================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_vlant_wait_for_completion() function is very similar to the
ocelot_mact_wait_for_completion(). It seemed to have be copied but the
comment was not updated, so let's fix it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig limitation of X86 is to too wide.
The ENA driver only requires a little endian dependency.
Change the dependency to be on little endian CPU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the switch driver (e.g., mlxsw_spectrum) determines it needs to
flash a new firmware version it resets the ASIC after the flashing
process. The bus driver (e.g., mlxsw_pci) then registers itself again
with mlxsw_core which means (among other things) that the device
registers itself again with the hwmon subsystem again.
Since the device was registered with the hwmon subsystem using
devm_hwmon_device_register_with_groups(), then the old hwmon device
(registered before the flashing) was never unregistered and was
referencing stale data, resulting in a use-after free.
Fix by removing reliance on device managed APIs in mlxsw_hwmon_init().
Fixes: c86d62cc41 ("mlxsw: spectrum: Reset FW after flash")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to d49c88d767 ("r8169: Enable MSI-X on RTL8106e") after
e9d0ba506ea8 ("PCI: Reprogram bridge prefetch registers on resume")
we can safely assume that this also fixes the root cause of
the issue worked around by 7c53a72245 ("r8169: don't use MSI-X on
RTL8168g"). So let's revert it.
Fixes: 7c53a72245 ("r8169: don't use MSI-X on RTL8168g")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang currently warns:
drivers/net/ethernet/qlogic/qla3xxx.c:384:24: warning: signed shift
result (0xF00000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
~~~~~~~~~~~~~~ ^ ~~
1 warning generated.
The warning is certainly accurate since ISP_NVRAM_MASK is defined as
(0x000F << 16) which is then shifted by 16, resulting in 64424509440,
well above UINT_MAX.
Given that this is the only location in this driver where ISP_NVRAM_MASK
is shifted again, it seems likely that ISP_NVRAM_MASK was originally
defined without a shift and during the move of the shift to the
definition, this statement wasn't properly removed (since ISP_NVRAM_MASK
is used in the statenent right above this). Only the maintainers can
confirm this since this statment has been here since the driver was
first added to the kernel.
Link: https://github.com/ClangBuiltLinux/linux/issues/127
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all RQ/SQ/CQ
contexts of a NIX LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the RQ/SQ/CQ contexts.
So a bitmap is introduced to keep track of enabled NIX RQ/SQ/CQ
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NIX AQ
via mbox. Instructions can be to init/write/read RQ/SQ/CQ/RSS
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate bitmaps and memory for PFVF mapping info for
maintaining NIX transmit scheduler queues maintenance.
PF/VF drivers will request for alloc, free e.t.c of
Tx schedulers via mailbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Config LSO formats for TSOv4 and TSOv6 offloads.
These formats tell HW which fields in the TCP packet's
headers have to be updated while performing segmentation
offload.
Also report PF/VF drivers the LSO format indices as part
of response to NIX_LF_ALLOC mbox msg. These indices are
used in SQE extension headers while framing SQE for pkt
transmission with TSO offload.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NIX_LF_ALLOC mbox message allocate memory for
NIXLF's CQ, SQ, RQ, CINT, QINT and RSS HW contexts and configure
respective base iova HW. Enable caching of contexts into NIX NDC.
Return SQ buffer (SQB) size, this PF/VF MAC address etc info
e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NIX admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NIX LFs will submit
instructions to AQ to init/write/read RQ/SQ/CQ/RSS contexts
and in case of read, get context from result memory.
Also before configuring/using NIX block calibrate X2P bus
and check if NIX interfaces like CGX and LBK are in active
and working state.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF to disable all Aura/Pool
contexts of a NPA LF via mbox. This will be used by PF/VF drivers
upon teardown or while freeing up HW resources.
A HW context which is not INIT'ed cannot be modified and a
RVU PF/VF driver may or may not INIT all the Aura/Pool contexts.
So a bitmap is introduced to keep track of enabled NPA Aura/Pool
contexts, so that only enabled hw contexts are disabled upon LF
teardown.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to submit instructions to NPA AQ
via mbox. Instructions can be to init/write/read Aura/Pool/Qint
contexts. In case of read, context will be returned as part of
response to the mbox msg received.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving NPA_LF_ALLOC mbox message allocate memory for
NPALF's aura, pool and qint contexts and configure the same
to HW. Enable caching of contexts into NPA NDC.
Return pool related info like stack size, num pointers per
stack page e.t.c to the mbox msg sender.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize NPA admin queue (AQ) i.e alloc memory for
AQ instructions and for the results. All NPA LFs will submit
instructions to AQ to init/write/read Aura/Pool contexts
and in case of read, get context from result memory.
Added some common APIs for allocating memory for a queue
and get IOVA in return, these APIs will be used by
NIX AQ and for other purposes.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to enable or disable internal loopback mode in CGX.
New mbox IDs CGX_INTLBK_ENABLE/DISABLE added for this.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving notification from firmware the CGX event handler
in the AF driver gets the current link info such as status, speed,
duplex etc from CGX driver and sends it across to PFs who have
registered to receive such notifications.
To support above
- Mbox messaging support for sending msgs from AF to PF has been added.
- Added mbox msgs so that PFs can register/unregister for link events.
- Link notifications are sent to PF under two scenarioss.
1. When a asynchronous link change notification is received from
firmware with notification flag turned on for that PF.
2. Upon notification turn on request, the current link status is
send to the PF.
Also added a new mailbox msg using which RVU PF/VF can retrieve
their mapped CGX LMAC's current link info. Link info includes
status, speed, duplex and lmac type.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting MAC address filters in CGX
for PF interfaces. Also PF interfaces can be put in promiscuous
mode. Dataplane PFs access this functionality using mailbox
messages to the AF driver.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a RVU PF/VF driver to retrieve
it's mapped CGX LMAC Rx and Tx stats from AF via mbox.
New mailbox msg is added is added.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new mailbox msgs for RVU PF/VFs to request AF
to enable/disable their mapped CGX::LMAC Rx & Tx.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looping on a integer timeout, use time_before(jiffies),
so that maximum poll time is capped.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, VxLAN encapsulation takes place in the FDB table where
certain {MAC, FID} entries are programmed with an underlay unicast IP.
MAC addresses that are not programmed in the FDB are flooded to the
relevant local ports and also to a list of underlay unicast IPs that are
programmed using the all zeros MAC address in the VxLAN driver.
One difference between the hardware and software data paths is the fact
that in the software data path there are two FDB lookups prior to the
encapsulation of the packet. First in the bridge's FDB table using {MAC,
VID} and another in the VxLAN's FDB table using {MAC, VNI}.
Therefore, when a new VxLAN FDB entry is notified, it is only programmed
to the device if there is a corresponding entry in the bridge's FDB
table. Similarly, when a new bridge FDB entry pointing to the VxLAN
device is notified, it is only programmed to the device if there is a
corresponding entry in the VxLAN's FDB table.
Note that the above scheme will result in a discrepancy between both
data paths if only one FDB table is populated in the software data path.
For example, if only the bridge's FDB is populated with an entry
pointing to a VxLAN device, then a packet hitting the entry will only be
flooded by the kernel to remote VTEPs whereas the device will also flood
the packets to other local ports member in the VLAN.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enslavement of VxLAN devices to offloaded bridges was never forbidden by
mlxsw, but this patch makes sure the required configuration is performed
in order to allow VxLAN encapsulation and decapsulation to take place in
the device.
The patch handles both the case where a VxLAN device is enslaved to an
already offloaded bridge and the case where the first mlxsw port is
enslaved to a bridge that already has VxLAN device configured.
Invalid configurations are sanitized and an error string is returned via
extack.
Since encapsulation and decapsulation do not occur when the VxLAN device
is down, the driver makes sure to enable / disable these functionalities
based on NETDEV_PRE_UP and NETDEV_DOWN events.
Note that NETDEV_PRE_UP is used in favor of NETDEV_UP, as the former
allows to veto the operation, if necessary.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to determine whether a netdev is a VxLAN netdev by
calling the above mentioned function that checks the netdev's
rtnl_link_ops.
This will allow modules to identify netdev events involving a VxLAN
netdev and act accordingly. For example, drivers capable of VxLAN
offload will need to configure the underlying device when a VxLAN netdev
is being enslaved to an offloaded bridge.
Convert nfp to use the newly introduced helper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a local route that matches the source IP of an offloaded NVE tunnel
is notified, the driver needs to program it to perform NVE decapsulation
instead of merely trapping packets to the CPU.
This patch complements "mlxsw: spectrum_router: Enable local routes
promotion to perform NVE decap" where existing local routes were
promoted to perform NVE decapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1D FIDs are used to represent VLAN-unaware bridges and currently
this is the only type of FID that supports NVE configuration.
Since the NVE tunnel device does not take a reference on the FID, it is
possible for the FID to be destroyed when it still has NVE
configuration.
Therefore, when destroying the FID make sure to disable its NVE
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The common NVE core expects each encapsulation type to implement a
certain set of operations that are specific to this type and the
currently used ASIC. These operations include things such as the ability
to determine whether a certain NVE configuration can be offloaded and
ASIC-specific initialization for this type.
Implement these operations for VxLAN on the Spectrum ASIC. Spectrum-2
support will be added by a future patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum ASIC supports different types of NVE encapsulations (e.g.,
VxLAN, NVGRE) with more types to be supported by future ASICs.
Despite being different, all these encapsulations share some common
functionality such as the enablement of NVE encapsulation on a given
filtering identifier (FID) and the addition of remote VTEPs to the
linked-list of VTEPs that traffic should be flooded to.
Implement this common core and allow different ASICs to register
different operations for different encapsulation types.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, different VRFs (routing tables) are represented using
different virtual routers (VRs) and thus the kernel's table IDs are
mapped to VR IDs.
Allow internal users of the IP router to query the VR ID based on a
kernel table ID.
This is needed - for example - when configuring the underlay VR where
VxLAN encapsulated packets will undergo an L3 lookup. In this case, the
kernel's table ID is derived from the VxLAN device's configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an NVE tunnel with an IP underlay (e.g., VxLAN) is configured the
local route to the tunnel's source IP needs to be promoted to perform
NVE decapsulation.
Expose an API in the unicast IP router to promote / demote local routes.
The case where a local route is configured after the creation of the NVE
tunnel will be handled in a subsequent patch in the set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current APIs only allow looking for a FID and creating it in case it
does not exist.
With VxLAN, in case the bridge to which the VxLAN device was enslaved
does not already have a corresponding FID, then it means that something
went wrong that we need to be aware of.
Add an API to look up a FID, but without creating it in order to catch
above-mentioned situation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, the VNI and the list of remote VTEPs a packet should be
flooded to is a property of the filtering identifier (FID).
During encapsulation, the VNI is taken from the FID the packet was
classified to. During decapsulation, the overlay packet is injected into
a bridge and classified to a FID based on the VNI it came with.
Allow NVE configuration for a FID. Currently, this is only supported
with 802.1D FIDs which are used for VLAN-unaware bridges. However, NVE
configuration is going to be supported with 802.1Q FIDs which is why the
related fields are placed in the common FID struct.
Since the device requires a 1:1 mapping between FID and VNI, the driver
maintains a hashtable keyed by VNI and checks if the VNI is already
associated with an existing FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we fail when user specify a non-zero chain, this patch adds the
support for it and tc priorities. To get to a new chain, use the tc
goto action.
Currently we support a fixed prio range 1-16, and chain range 0-3.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When adding a vxlan tc rule, and a neighbour isn't available, we
don't insert any rule to hardware. Once we enable offloading flows
with multiple priorities, a packet that should have matched this rule
will continue in hardware pipeline and might match a wrong one.
This is unlike in tc software path where it will be matched and
forwarded to the vxlan device (which will cause a ARP lookup
eventually) and stop processing further tc filters.
To address that, when when a neighbour isn't available (EAGAIN from
attach_encap), or gets deleted, change the original action to be a
forward to slow path instead. Neighbour update will restore the original
action once the neighbour becomes available. This will be done atomically
so at any given time we will have a the correct match.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A pre-step for the tc offloads code to use this when a neigh is
not available for encap rules.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The code for adding/deleting fdb flow is repeated when
user-space does flow add/del and when we add/del from
the neigh update path - unify them to avoid the duplication.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When replacing a tc flower rule, flower first requests to add the
new rule (new action), then deletes the old one.
But currently when asked to add a new tc flower flow, we append the
actions (and counters to it).
This can result in a fte with two flow counters or conflicting
actions (drop and encap action) which firmware complains/errs
about and isn't achieving what the user aimed for.
Instead, insert the flow using the new no-append flag which will add a
new HW rule, the old flow and rule will be deleted later by flower
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanmox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If no-append flag is set, we will add a new FTE, instead of appending
the actions of the inserted rule when the same match already exists.
While here, move the has_flow_tag boolean indicator to be a flag too.
This patch doesn't change any functionality.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanmox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A chain is a group of priorities, so use the fdb parallel
sub namespaces to implement chains, and a flow table for each
priority in them.
Because these namespaces are parallel and in series to the slow path
fdb, the chains aren't connected to one another (but to the slow path),
and one must use a explicit goto action to reach a different chain.
Flow tables for the priorities will be created on demand and destroyed
once not used.
The Firmware has four pools of tables for sizes S/XS/M/L (4k, 64k, 1m, 4m).
We maintain ghost copies of the pools occupancy.
When a new table is to be created, we scan the pools from large to small
and find the 1st table size which can be now created. When a table is
destroyed, we update the relevant pool.
Multi chain/prio isn't enabled yet by this patch, for now all flows
will use the default chain 0, and prio 1.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Be symmetric with the e-switch API to add rules which has a
specific function to add fwd rules which are used as part of
vport mirroring.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards supporting multi-chains and priorities, split the FDB fast path
to multiple namespaces (sub namespaces), each with multiple priorities.
This patch adds a new flow steering type, FS_TYPE_PRIO_CHAINS, which is
like current FS_TYPE_PRIO, but may contain only namespaces, and those
will be in parallel to one another in terms of managing of the flow
tables connections inside them. Meaning, while searching for the next
or previous flow table to connect for a new table inside such namespace
we skip the parallel namespaces in the same level under the
FS_TYPE_PRIO_CHAINS prio we originated from.
We use this new type for splitting the fast path prio into multiple
parallel namespaces, each containing normal prios.
The prios inside them (and their tables) will be connected to one
another, but not from one parallel namespace to another, instead the
last prio in each namespace will be connected to the next prio in
the containing FDB namespace, which is the slow path prio.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move to have clear separation on the code path to add nic vs e-switch
flows. While here we break the code that deals with adding offloaded
TC tool to few smaller stages, each on helper function.
Besides getting us simpler and readable code, these are pre-steps
for being able to have two HW flows serving one SW TC flow for some
e-switch use cases.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the flow add utility functions to return err code instead of rule
pointers. This will allow for simpler logic when one tc rule is
duplicated to two HW rules in downstream patches.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when a flow rule is created using the FS core layer, the caller
has to pass the entire flow counter object and not just the counter HW
handle (ID). This requires both the FS core and the caller to have
knowledge about the inner implementation of the FS layer flow counters
cache and limits the possible users.
Move to use the counter ID across the place when dealing with flows.
Doing this decoupling, now can we privatize the inner implementation
of the flow counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There's no real reason for the e-switch logic to manage the creation of
counters for offloaded flows. The API already has the directive for the
caller to denote they want to attach a counter to the created flow.
As such, we go and move the management of flow counters to the mlx5e
tc offload logic. This also lets us remove an inelegant interface where
the FS layer had to provide a way to retrieve a counter from a flow rule.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 updates for both net-next and rdma-next
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux: (21 commits)
net/mlx5: Expose DC scatter to CQE capability bit
net/mlx5: Update mlx5_ifc with DEVX UID bits
net/mlx5: Set uid as part of DCT commands
net/mlx5: Set uid as part of SRQ commands
net/mlx5: Set uid as part of SQ commands
net/mlx5: Set uid as part of RQ commands
net/mlx5: Set uid as part of QP commands
net/mlx5: Set uid as part of CQ commands
net/mlx5: Rename incorrect naming in IFC file
net/mlx5: Export packet reformat alloc/dealloc functions
net/mlx5: Pass a namespace for packet reformat ID allocation
net/mlx5: Expose new packet reformat capabilities
{net, RDMA}/mlx5: Rename encap to reformat packet
net/mlx5: Move header encap type to IFC header file
net/mlx5: Break encap/decap into two separated flow table creation flags
net/mlx5: Add support for more namespaces when allocating modify header
net/mlx5: Export modify header alloc/dealloc functions
net/mlx5: Add proper NIC TX steering flow tables support
net/mlx5: Cleanup flow namespace getter switch logic
net/mlx5: Add memic command opcode to command checker
...
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add link establishment methods
Add auto negotiation methods
Add read MAC address method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for NVM support and get MAC address, complete probe
method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for hardware initialization and reset
Add code for semaphore handling
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for allocating, configuring, and freeing Tx/Rx ring
resources. With these changes in place the descriptor queues are in a
state where they are ready to transmit or receive if provided buffers.
This also adds the transmit and receive fastpath and interrupt handlers.
With this code in place the network device is now able to send and receive
frames over the network interface using a single queue.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch set adds interrupt support for the igc interfaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the ability to configure the basic settings on the device
we can start allocating and configuring a netdev for the interface.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation. With this it is possible to bring up the interface,
but without being able to configure any of the filters on
the interface itself.
Add skeleton for a function pointers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add
the igc driver which supports the Intel(R) I225-LM/I225-V 2.5G
Ethernet Controller.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update cxgb4 to send No. of Tx Queue created in lldinfo struct
and use the same ntxq in chcr driver.
This patch depends on following commit
commit add92a817e
"Fix memory corruption in DMA Mapped buffers"
v2:
Free txq_info in error case as pointed by Lino Sanfilippo.
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Program translation stage checks that program can be offloaded to
the netdev which was passed during the load (bpf_attr->prog_ifindex).
After program sharing was introduced, however, the netdev on which
program is loaded can theoretically be different, and therefore
we should recheck the program size and max stack size at load time.
This was found by code inspection, AFAIK today all vNICs have
identical caps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Atomic operations on the NFP are currently always in big endian.
The driver keeps track of regions of memory storing atomic values
and byte swaps them accordingly. There are corner cases where
the map values may be initialized before the driver knows they
are used as atomic counters. This can happen either when the
datapath is performing the update and the stack contents are
unknown or when map is updated before the program which will
use it for atomic values is loaded.
To avoid situation where user initializes the value to 0 1 2 3
and then after loading a program which uses the word as an atomic
counter starts reading 3 2 1 0 - only allow atomic counters to be
initialized to endian-neutral values.
For updates from the datapath the stack information may not be
as precise, so just allow initializing such values to 0.
Example code which would break:
struct bpf_map_def SEC("maps") rxcnt = {
.type = BPF_MAP_TYPE_HASH,
.key_size = sizeof(__u32),
.value_size = sizeof(__u64),
.max_entries = 1,
};
int xdp_prog1()
{
__u64 nonzeroval = 3;
__u32 key = 0;
__u64 *value;
value = bpf_map_lookup_elem(&rxcnt, &key);
if (!value)
bpf_map_update_elem(&rxcnt, &key, &nonzeroval, BPF_ANY);
else
__sync_fetch_and_add(value, 1);
return XDP_PASS;
}
$ offload bpftool map dump
key: 00 00 00 00 value: 00 00 00 03 00 00 00 00
should be:
$ offload bpftool map dump
key: 00 00 00 00 value: 03 00 00 00 00 00 00 00
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When sending a big fragment using multiple buffer descriptor,
hns3 does one maping, but do multiple unmapping when tx is done,
which may cause unmapping problem.
To fix it, this patch makes sure the value of desc_cb.length of
the non-first bd is zero. If desc_cb.length is zero, we do not
unmap the buffer.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep symmetrical, this patch renames hns_nic_dma_unmap to
hns3_clear_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unifies big tx fragment handling for tso and non-tso
case.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To solve the L3 checksum error problem which happens when driver
does not clear L3 checksum, DMA map should be done after calling
skb_cow_head.
This patch moves DMA map into hns3_fill_desc to ensure that DMA
map is done after calling skb_cow_head.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes hns3_fill_desc_tso in preparation for
fixing some desc filling bug, because for tso or non-tso
case, we will use the unified hns3_fill_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly added link modes are required to be added
during setting link modes. If the new link mode
is not available during qed_set_link, it may cause
link getting down due to empty supported capability,
being passed to MFW, after setting autoneg off/on
with current/supported speed.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set link mode after checking available "supported" link caps
of the port.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver modes with different speed and media type,
speed capability and supported board types in HSI, which
will be utilizing to display correct specification of link
modes and speed type.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the use of local PTT to propagate through the qed_mcp* API's.
Global ptt should not be used.
Register access should be done through layers. Register address is
mapped into a PTT, PF translation table. Several interface functions
require a PTT to direct read/write into register. There is a pool of
PTT maintained, and several PTT are used simultaneously to access
device registers in different flows. Same PTT should not be used in
flows that can run concurrently.
To avoid running out of PTT resources, too many PTT should not be
acquired without releasing them. Every PF has a global PTT, which is
used throughout the life of PF, in most important flows for register
access. Generic functions acquire the PTT locally and release after
the use. This patch aligns the use of Global PTT and Local PTT
accordingly.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c:282:5: warning:
symbol 'aq_fw2x_update_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when populating the set ipv6 address action, we incorrectly
made use of pedit's key index to determine which 32bit word should be
set. We now calculate which word has been selected based on the offset
provided by the pedit action.
Fixes: 354b82bb32 ("nfp: add set ipv6 source and destination address")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only allowed a single header key per pedit action to
change the header. This used to result in the last header key in the
pedit action to overwrite previous headers. We now keep track of them
and allow multiple header keys per pedit action.
Fixes: c0b1bd9a8b ("nfp: add set ipv4 header action flower offload")
Fixes: 354b82bb32 ("nfp: add set ipv6 source and destination address")
Fixes: f8b7b0a6b1 ("nfp: add set tcp and udp header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not correctly change headers when using multiple
pedit actions with partial masks. We now take this into account and
no longer just commit the last pedit action.
Fixes: c0b1bd9a8b ("nfp: add set ipv4 header action flower offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit db65f35f50 ("net: fec: add support of ethtool get_regs") introduce
ethool "--register-dump" interface to dump all FEC registers.
But not all silicon implementations of the Freescale FEC hardware module
have the FRBR (FIFO Receive Bound Register) and FRSR (FIFO Receive Start
Register) register, so we should not be trying to dump them on those that
don't.
To fix it we create a quirk flag, FEC_QUIRK_HAS_RFREG, and check it before
dump those RX FIFO registers.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new poll function that polls for NQ events. If the NQ event is
a CQ notification, we locate the CP ring from the cq_handle and call
__bnxt_poll_work() to handle RX/TX events on the CP ring.
Add a new has_more_work field in struct bnxt_cp_ring_info to indicate
budget has been reached. __bnxt_poll_cqs_done() is called to update or
ARM the CP rings if budget has not been reached or not. If budget
has been reached, the next bnxt_poll_p5() call will continue to poll
from the CQ rings directly. Otherwise, the NQ will be ARMed for the
next IRQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
