The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
This patch reverts commit ccb4ada2f1 ("ARM: dts: sun7i: Add A20 SRAM and
SRAM controller"), commit e6f51e4bd2 ("ARM: dts: sun5i: Add A13 and A10s
SRAM and SRAM controller") and commit 6d92b80f35 ("ARM: dts: sun4i: Add
A10 SRAM and SRAM controller").
The bindings have been changed in the SRAM driver, and we need to
change the DT accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On A80 there are 2 watchdogs, one in the main block, and one in the
R (special) block. We do not have information on the R block watchdog,
other than the register layout is the same, and the interrupt number.
Both are able to reset the whole system.
Add the main watchdog, in case the R block is used for special purposes
like running an RTOS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BananaPro uses uart4 for the default rx/tx pins on the 40 pins connector,
so enable uart4.
Uart2 is also available at the bananapro io-pins, but like on the bananapi
the primary function of the pins is to act as gpios, see:
http://forum.lemaker.org/forum.php?mod=viewthread&tid=10852
Remove the uart2 node, people who want to use uart2 can do so with a
devicetree-overlay.
Signed-off-by: Michael Ring <mail@michael-ring.org>
[hdegoede@redhat.com: Remove uart2 node]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards (e.g. the BananaPro) use alternative pins for uart4, add a pinmux
entry for these.
Signed-off-by: Michael Ring <mail@michael-ring.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl groups for SPI until now were also adding the chip selects in
the SPI pinctrl group.
This was causing a few issues, since a board was forced to use a random
number of chipselects, even though it might use one of these chip selects
for another pin.
The number of chipselects defined was also not the same from one group to
another because of different needs at the time these groups have been
introduced, resulting in no clear view from the board DTS on what exactly
is being muxed, which even might change in the future.
Solve this by creating different pinctrl groups for the chipselects and the
standard SPI pins (CLK, MOSI and MISO) so that we fix both issues.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines (probably copy pasted) have an indentation mixing tabs and
spaces that triggers a checkpatch warning.
Fix those, and while we're at it, fix the space-indented sections.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few lines in our DTSIs are over the 80 characters limit, making
checkpatch complain about that.
If possible (and relevant), wrap these lines to 80 characters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently none of the target boards nor the driver supports
IR TX. However this pin is used in a few instances as a GPIO.
Split the pin ctrl descriptions so that only the IR RX is
configured to be used.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash,
a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles,
a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV.
This patch adds basic support for the device, more information can be found
here (http://linux-sunxi.org/MK808C).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On sun6i we already have PLL6 as AHB1 clock's parent. However this was
previously set in the dma controller node, which takes effect when the
dma controller is probed.
We want this to take effect as soon as possible, so hrtimer rate
calculation is correct, and to be sure the AHB1 clock rate remains as
stable as possible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock driver now supports a muxable ahb clock. Update the dtsi
with the proper compatible and add the new parent clocks.
This also adds the new pll6/4 output for pll6 on sun7i-a20. The
output is not used on sun4/5i.
Also use assigned-clocks to reparent ahb to pll6. We want ahb to
have a stable, non-changing clock rate. cpu/axi clock rate changes
as a result of newly added cpufreq support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Jesurun Q5 has a black plastic casing with the approximate dimensions
of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it
features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The
external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female
jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the
device has 1x red LED (hard wired to power) and an programmable green led.
On the board there is also an unpopulated IR receiver and the UART.
The devices is equipped with an AXP209 PMU.
For more details see: http://linux-sunxi.org/Jesurun_Q5
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the chipone-icn8318 touchscreen found on the Utoo P66 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi mini is a development board using the Allwinner A20 SoC,
with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI,
1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports,
ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pi_Minihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM,
microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A
ports, ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[hdegoede@redhat.com: Do not change soc node name, change compatible to
sun4i-a10-sram-controller to match the driver change]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13 / A10s has a few SRAM that can be mapped either to a device or to
the CPU, with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The eMMC on the A13 based Utoo-P66 tablet does not properly support hpi,
and trying to enable it results in the eMMC not working, so add a child-node
describing the eMMC, and set the broken-hpi property on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the a list compiled by Maxime Ripard,
which is based on A31 FEX files from the sunxi-boards repository. Not all
boards have the same settings. The settings in this patch are the ones
shared by A/B/C revisions, plus the default clock setting from u-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the unused usb1_vbus_pin_csq908 node (vbus is always on on the cs908),
and sort the remaining nodes alphabetically.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since the phy core already supports specifying a regulator to handle
during power up/down, it was decided to drop the regulator support
in the sun9i usb phy driver.
This patch switches the DT to the core bindings. This and the phy driver
would be in the same release and should not be a problem as far as DT
stability goes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has the architected timer, but the existing firmware from
Allwinner does not set CNTFRQ at all.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 SoC has the architected timer, but the existing firmware from
Allwinner does not set CNTFRQ at all.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The
WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO.
The IC also takes a power enable signal via GPIO. This is supported
with the new power sequencing bindings.
The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not enabled yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc1 is used to connect to the WiFi chip on the Hummingbird A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[maxime: Changed the drive and pull values for their defines]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Sometimes we need to specify non-probably information for sdio devices in the
devicetree, this is done through child nodes addressed by the reg property,
whereby the reg property refers to the sdio function number, see;
Documentation/devicetree/bindings/mmc/mmc.txt
This commit adds the necessary address- and size-cells properties to the mmc
controller nodes in the dtsi files, so that dts files needing such a child
node do not need to specify these themselves.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the AXP221 regulators. Only the ones directly used
on the board are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the
P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The p2wi controller has only one possible pinmux setting. Use it by
default in the dtsi, instead of having to set it in each board's dts.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: reformat commit title; rename p2wi pins and use as default]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.
[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds vendor-prefix for Wexler.
WEXLER trademark owned by AVIRSA Electronics, a member of the
diversified holding AVIRSA.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add support for Wexler TAB7200 tablet.
The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The touchscreen controller in the A13 and later has a different temperature
curve than the one in the original A10, change the compatible for the A13 and
later so that the kernel will use the correct curve.
Reported-by: Tong Zhang <lovewilliam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a cubietech vendor prefix, as it is missing. The cubietruck, cubieboard2,
and cubieboard all already reference this prefix.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
lcd screen, 512MB RAM & 4GB emmc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The auxtek-t004:
http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
a 2 micro-usb receptacles, one for power and one for USB OTG.
The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add A13 mmc2 pinmux settings, note these are for a 8bit bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13 and the A10s use the same die (this has been confirmed by Allwinner),
as such there is no need to differentiate between the ehci/ohci parts of both,
the only reasons there were different allwinner,sun5i-a*-foo compatible
between these 2 parts is costemetically and because we could when we still
had 2 completely different dtsi files.
The allwinner,sun5i-a*-foo compatible strings are not used for binding at all,
the actual driver binds to the generic-?hci compatible, so we can safely remove
this cosmetical difference and simplify the dtsi files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM,
8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using
USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out,
a TRS connector for A/V, SPDIF and IrDA.
This patch adds basic support for the device, more information can
be found here (http://linux-sunxi.org/Mele_I7).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
