qxl doesn't have any functions for setting the gamma table, so this is
completely defunct.
Not nice to lie to userspace, so let's stop!
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-10-git-send-email-daniel.vetter@ffwll.ch
Again the fbdev emulation gamma_set/get functions are only needed for
drivers that try to also use 8bpp paletted mode. Which msm doesn't, so
this is dead code. Let's rip it out.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-7-git-send-email-daniel.vetter@ffwll.ch
DRM fbdev emulation only supports pallete_color with depth == 8, and
truecolor with depth > 8. Handling depth == 16 for palettes is hence
dead code, let's remove it.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-3-git-send-email-daniel.vetter@ffwll.ch
So far we've got one condition when DRM drivers need to defer probing
on a dual GPU system and it's coded separately into each of the relevant
drivers. As suggested by Daniel Vetter, deduplicate that code in the
drivers and move it to a new vga_switcheroo helper. This yields better
encapsulation of concepts and lets us add further checks in a central
place. (The existing check pertains to pre-retina MacBook Pros and an
additional check is expected to be needed for retinas.)
One might be tempted to check deferred probing conditions in
vga_switcheroo_register_client(), but this is usually called fairly late
during driver load. The GPU is fully brought up and ready for switching
at that point. On boot the ->probe hook is potentially called dozens of
times until it finally succeeds, and each time we'd repeat bringup and
teardown of the GPU, lengthening boot time considerably and cluttering
logfiles. A separate helper is therefore needed which can be called
right at the beginning of the ->probe hook.
Note that amdgpu currently does not call this helper as the AMD GPUs
built into MacBook Pros are only supported by radeon so far.
v2: This helper could eventually be used by audio clients as well,
so rephrase kerneldoc to refer to "client" instead of "GPU"
and move the single existing check in an if block specific
to PCI_CLASS_DISPLAY_VGA devices. Move documentation on
that check from kerneldoc to a comment. (Daniel Vetter)
v3: Mandate in kerneldoc that registration of client shall only
happen after calling this helper. (Daniel Vetter)
v4: Rebase on 412c8f7de0 ("drm/radeon: Return -EPROBE_DEFER when
amdkfd not loaded")
v5: Some Optimus GPUs use PCI_CLASS_DISPLAY_3D, make sure those are
matched as well. (Emil Velikov)
v6: The if-condition referring to PCI_BASE_CLASS_DISPLAY may be
considered a functional change. Move to a separate commit to
keep this a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/575885fd440c2b13c3f19ddf44360cfbbff35f50.1464685538.git.lukas@wunner.de
When a CRTC is going to be disabled, it's state may contain a display mode
with zeroed content. This could be reproduced by HDMI cable hotplug out
operation with legacy fbdev support in dual display cases. It would confuse
driver's CRTC callback ->mode_fixup and make the total state be rejected.
So, let's don't call the callback for the CRTC.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464341754-7087-1-git-send-email-gnuiyl@gmail.com
This patch aims to replace the roll-your-own seqlock implementation with
full-blown seqlock'. We also remove the timestamp ring-buffer in favour
of single timestamp/count pair protected by a seqlock. In turn this
means we can now increment the vblank freely without the need for
clamping.
v2:
- reduce the scope of the seqlock, keeping vblank_time_lock
- make the seqlock per vblank_crtc, so multiple readers aren't blocked by
the writer
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462890088-18194-1-git-send-email-matthew.auld@intel.com
The tiled 5K Dell monitor appears to be hiding it's tiled mode
inside the displayid timings block, this patch parses this
blocks and adds the modes to the modelist.
v1.1: add missing __packed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will iterate over all DisplayID blocks found in the buffer.
Previously only the first block was parsed.
https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Tomas Bzatek <tomas@bzatek.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was added in
commit 0a3e67a4ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Sep 30 12:14:26 2008 -0700
drm: Rework vblank-wait handling to allow interrupt reduction.
to stay backwards-compatible with old UMS code that didn't even tell
the kernel when it did a modeset, so that the kernel could
save/restore vblank counters. At worst this means vblanks will be
somewhat funky on a setup that very likely no one still runs.
So let's just nuke it.
Plan B would be to set it unconditionally in drm_vblank_init for kms
drivers, instead of in each driver separately. So if this patch breaks
anything please only restore the hunks in drmP.h and drm_irq.c, plus
add a check for DRIVER_MODESET in drm_vblank_init.
Stumbled over this in a discussion on irc with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull request of 2016-05-20
* tag 'vmwgfx-next-160520' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
Nothing too exciting here, there's a larger chunk of work that still
needs more testing but not likely to get that done today - so - here's
the rest of it. Assuming nothing else goes horribly wrong, I should be
able to send the rest Monday if it isn't too late....
Changes:
- Improvements to power sensor support
- Initial attempt at GM108 support
- Minor fixes to GR init + ucode
- Make use of topology information (provided by the GPU) in various
places, should at least fix some fault recovery issues and
engine/runlist mapping confusion on newer GPUs.
* 'linux-4.7' of git://github.com/skeggsb/linux: (51 commits)
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
drm/nouveau/gr/gm200-: fix bad hardcoding of a max-tpcs-per-gpc value
drm/nouveau/gr/gm200-: rop count == ltc count
drm/nouveau/gr/gm200: modify the mask when copying mmu settings from fb
drm/nouveau/gr/gm200: move some code into init_gpc_mmu() hook
drm/nouveau/gr/gm200: make generate_main() static
drm/nouveau/gr/gf100-: abstract fetching rop count
drm/nouveau/gr/gf100-: rename magic_not_rop_nr to screen_tile_row_offset
drm/nouveau/gr/gf100-: remove hardcoded idle_timeout values
...
When tracking down a customer issue, it is useful to know exactly
which version of the vmwgfx they are using. Since vmware.log is
often the only available debug log, report vmwgfx version in there.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
This patch adds capabilities for a VMWare guest to send and
receive messages from the host, and adds functions to sending log
messages to vmware.log and to request device settings that aren't
available through the virtual hardware, e.g. certain settings in
the VMX file.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Some global KMS state that is elsewhere protected by the mode_config
mutex here needs to be protected with a local mutex. Remove corresponding
lockdep checks and introduce a new driver-private global_kms_state_mutex,
and make sure its locking order is *after* the crtc locks in order to
avoid having to release those when the new mutex is taken.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org> # 4.6
This is a simplied version of the fix by Roy in fdo#93629. While this
doesn't appear to fix the issues for the users in that report, it's a
real issue that deserves to be resolved.
Reported-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also removes an XXX; according to nvgpu headers the field is called
NV_PGRAPH_GPCS_SWDX_TC_BETA_CB_SIZE_DIV3, so, apparently not some
magic we need to figure out :)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was really inconsistent, some implementations could touch PPCs
that didn't exist, others neglected to touch ones that did.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We always want a equal or higher voltage than the requested ones, otherwise
nouveau undervolts.
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Appears to more closely match what RM does.
For GM20B, now also copying bit 12 from NV_PFB_MMU_CTRL as upcoming
changes will require it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It appears these don't map to PBDMAs (at least on Kepler, it may or may
be valid for Fermi - this hasn't been checked), but to runlists.
This drops the NVKM_ENGINE_FIFO data from the entries too, as resetting
all of PFIFO is *not* the way to handle such faults.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>