DK had pointed out a comment there was hard to understand, so I
tried to read back again and I couldn't understand that as well.
So let me re-phrase that in a way that anyone can understand
later, even myself.
Also fixed the comment block style.
v2: Accept DK's suggestion on PSR_state 2 and PSR_state 3 named
as spec.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170912183059.5086-1-rodrigo.vivi@intel.com
The engine also provides a mirror of the CSB write pointer in the HWSP,
but not of our read pointer. To take advantage of this we need to
remember where we read up to on the last interrupt and continue off from
there. This poses a problem following a reset, as we don't know where
the hw will start writing from, and due to the use of power contexts we
cannot perform that query during the reset itself. So we continue the
current modus operandi of delaying the first read of the context-status
read/write pointers until after the first interrupt. With this we should
now have eliminated all uncached mmio reads in handling the
context-status interrupt, though we still have the uncached mmio writes
for submitting new work, and many uncached mmio reads in the global
interrupt handler itself. Still a step in the right direction towards
reducing our resubmit latency, although it appears lost in the noise!
v2: Cannonlake moved the CSB write index
v3: Include the sw/hwsp state in debugfs/i915_engine_info
v4: Also revert to using CSB mmio for GVT-g
v5: Prevent the compiler reloading tail (Mika)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913085605.18299-6-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
The engine provides a mirror of the CSB in the HWSP. If we use the
cacheable reads from the HWSP, we can shave off a few mmio reads per
context-switch interrupt (which are quite frequent!). Just removing a
couple of mmio is not enough to actually reduce any latency, but a small
reduction in overall cpu usage.
Much appreciation for Ben dropping the bombshell that the CSB was in the
HWSP and for Michel in digging out the details.
v2: Don't be lazy, add the defines for the indices.
v3: Include the HWSP in debugfs/i915_engine_info
v4: Check for GVT-g, it currently depends on intercepting CSB mmio
v5: Fixup GVT-g mmio path
v6: Disable HWSP if VT-d is active as the iommu adds unpredictable
memory latency. (Mika)
v7: Also markup the CSB read with READ_ONCE() as it may still be an mmio
read and we want to stop the compiler from issuing a later (v.slow) reload.
Suggested-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913133534.26927-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
At the time of commit 1f767e02d6 ("drm/i915: HWS must be in the
mappable region for g33"), drm_mm insertion would often default to
placing a new object high in the zone forcing us to specify that certain
HWSP must be bound within the low mappable region. Since then, drm_mm
has gained more finesse over its placement and exposes that to the
caller, commit 4e64e5539d ("drm: Improve drm_mm search (and fix
topdown allocation) with rbtrees"). As such where possible we want the
HWSP to be outside of the mappable aperture and so need to specify that
can be pinned high.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913085605.18299-4-chris@chris-wilson.co.uk
On gen8+ we're currently using the PPHWSP of the kernel ctx as the
global HWSP. However, when the kernel ctx gets submitted (e.g. from
__intel_autoenable_gt_powersave) the HW will use that page as both
HWSP and PPHWSP. This causes a conflict in the register arena of the
HWSP, i.e. dword indices below 0x30. We don't current utilize this arena,
but in the following patches we will take advantage of the cached
register state for handling execlist's context status interrupt.
To avoid the conflict, instead of re-using the PPHWSP of the kernel
ctx we can allocate a separate page for the HWSP like what happens for
pre-execlists platform.
v2: Add a use-case for the register arena of the HWSP.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499357440-34688-1-git-send-email-daniele.ceraolospurio@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913085605.18299-3-chris@chris-wilson.co.uk
Using the HWSP ggtt_offset to get the lrca offset is only correct if the
HWSP happens to be before it (when we reuse the PPHWSP of the kernel
context as the engine HWSP). Instead of making this assumption, get the
lrca offset from the kernel_context engine state.
And while looking at this part of the GuC interaction, it was also
noticed that the firmware expects the size of only the engine context
(context minus the execlist part, i.e. don't include the first 80
dwords), so pass the right size.
v2: Use the new macros to prevent abusive overuse of the old ones (Chris).
Reported-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170712193032.27080-2-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913085605.18299-2-chris@chris-wilson.co.uk
Not only the context image consist of two parts (the PPHWSP, and the
logical context state), but we also allocate a header at the start of
for sharing data with GuC. Thus every lrc looks like this:
| [guc] | [hwsp] [logical state] |
|<- our header ->|<- context image ->|
So far, we have oversimplified whenever we use each of these parts of the
context, just because the GuC header happens to be in page 0, and the
(PP)HWSP is in page 1. But this had led to using the same define for more
than one meaning (as a page index in the lrc and as 1 page).
This patch adds defines for the GuC shared page, the PPHWSP page and the
start of the logical state. It also updated the places where the old
define was being used. Since we are not changing the size (or format) of
the context, there are no functional changes.
v2: Use PPHWSP index for hws again.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170712193032.27080-1-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913085605.18299-1-chris@chris-wilson.co.uk
As realised by commit 9e3d6223d2 ("math64, timers: Fix 32bit
mul_u64_u32_shr() and friends"), GCC does not always generate ideal code
for performing a 32b x 32b multiply returning a 64b result (i.e. where
we idiomatically use u64 result = (u64)x * (u32)x).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913105154.2910-2-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
As realised by commit 9e3d6223d2 ("math64, timers: Fix 32bit
mul_u64_u32_shr() and friends"), GCC does not always generate ideal code
for performing a 32b x 32b multiply returning a 64b result (i.e. where
we idiomatically use u64 result = (u64)x * (u32)x). This catches a
couple of instances in the display code using (u64)x * (u32)y.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913105154.2910-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The sgt iterators cause an
drivers/gpu/drm/i915/i915_gpu_error.c:846 i915_error_object_create() warn: statement has no effect 7
everywhere they are used. If we change the code slightly, we can achieve
the same increment without altering the output or raising a warning.
text data bss dec hex filename
1267906 20587 3168 1291661 13b58d before
1267906 20587 3168 1291661 13b58d after
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170913105754.4423-1-chris@chris-wilson.co.uk
We never used it in i915 and it's going to be removed
in newer GuC firmwares anyway.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505252197-27696-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The default values for the default scheduling policy come from the
GuC firmware itself. Transform the magic numbers into defines.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505252197-27696-1-git-send-email-oscar.mateo@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The context descriptor is stored inside the per-engine context state, as
we only need to compute it once and access it frequently. However,
currently only intel_lrc.c has easy access, but i915_guc_submission.c
would like to frequently read it as well, and more so only ever needs
the lower 32bits. Make it an inline as the compiler should be able to
retrieve the value in less instructions than it takes to do the function
call:
add/remove: 0/1 grow/shrink: 1/0 up/down: 8/-45 (-37)
function old new delta
i915_guc_submit 621 629 +8
intel_lr_context_descriptor 45 - -45
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170912214905.21987-1-chris@chris-wilson.co.uk
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Min brightness value from vbt was missing for CNP platform.
This setting have to refer backlight ic spec to restrict
min backlight output. Without this restriction, driver would
allow to configure lower brightness value and violate
backlight ic requirement.
Fixes: 4c9f7086ac ("drm/i915/cnp: Backlight support for CNP.")
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505279961-16140-1-git-send-email-shawn.c.lee@intel.com
This reverts commit bbdf0b2ff3 ("drm/i915/bxt: Disable device ready
before shutdown command").
Disable device ready before shutdown command was added previously to
avoid a split screen issue seen on dual link DSI panels. As of now, dual
link is not supported and will need some rework in the upstream
code. For single link DSI panels, the change is not required. This will
cause failure in sending SHUTDOWN packet during disable. Hence reverting
the change. Will handle the change as part of dual link enabling in
upstream.
Fixes: bbdf0b2ff3 ("drm/i915/bxt: Disable device ready before shutdown command")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1504604671-17237-1-git-send-email-vidya.srinivas@intel.com
Following the simplification to a single lookup loop in commit
170fa29b14 ("drm/i915: Simplify eb_lookup_vmas()") and commit
d1b48c1e71 ("drm/i915: Replace execbuf vma ht with an idr"), we can go
one step further and reorder the error paths so that the state of the
local variable obj is always known to the compiler and doesn't need the
uninitialized_var markup to squelch a compiler warning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170912150752.20411-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The SDE interrupt bits 25, 26 and 27 are either reserved or meant for
DDI E hotplug in SPT+. These bits are meant for AUX channels only in LPT
and CPT, so add the appropriate checks.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170909004255.14827-1-dhinakaran.pandiyan@intel.com
Factor out setup_private_pat() for introducing the following patches.
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505202148-22959-1-git-send-email-zhi.a.wang@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Min brightness value from vbt was missing for BXT platform.
This setting have to refer backlight ic spec to restrict
min backlight output. Without this restriction, driver would
allow to configure lower brightness value and violate
backlight ic requirement.
Fixes: 0fb890c013 ("drm/i915/bxt: BLC implementation")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Gary C Wang <gary.c.wang@intel.com>
Signed-off-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505187390-7039-1-git-send-email-shawn.c.lee@intel.com
During IGT testing it has been shown that the specification
defined polling time of 1 us for FCLK_DONE, is sometimes not
enough. The issue is still reproducible while disabling
C-states through the PM QoS framework and also while disabling
preemtion. From this the most plausible explanation is that the
issue is due to a firmware flaw.
As a workaround, it is better to wait a little bit longer for
the FCLK_DONE to come around, than to leave with an DRM_ERROR
and having FCLK_DONE at a randome time after.
While spinning a list of igt tests prone to reproduce the issue
the FCLK_DONE poll failed at approximately 2% of the invocations
of the bdw_set_cdclk function. The longest poll time during this
testing was measured to ~7us. So, the suggested new poll time of
100us is on the safe side.
v2: Added more documentation about investigations done.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102243
Signed-off-by: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908132829.6312-1-marta.lofstedt@intel.com
Continue on VLV PSR split with vfunc, let's also create one
for enabling source.
Also since we are touching *_enable_source functions let's
fix a comment with wrong name for vlv's one.
v2: Fix typo on commit message (DK).
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-12-rodrigo.vivi@intel.com
Continue on VLV PSR split with vfunc, let's also create
one for setting up VSC.
v2: Rebased on top of commit d2419ffc10 ("drm/i915: Plumb
crtc_state to PSR enable/disable")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-10-rodrigo.vivi@intel.com
Let's move the activation calls together after enable is done.
No real functional change should be expected here. Just an attempt
to get it clear when we are really activating PSR after enabling it.
v2: Add braces on if/else because commit message there is too long
as suggested by Jani.
v3: Rebased on top of commit d2419ffc10 ("drm/i915: Plumb
crtc_state to PSR enable/disable")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-9-rodrigo.vivi@intel.com
No functional change is expected here since at this point
PSR is not allowed to go to any active state. In other
words, not really enabled.
However let's do in a separated patch so it gets clear
on what is change and specially it can helps on bisect
case if we figure something has caused changes in behaviour.
But this needs to be done before we make the vfunc to
enable source to be in parity with VLV implementation.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-8-rodrigo.vivi@intel.com
This sequence is part of enable source anyways, but they
only need to be executed once and not on every activation,
So let's re-create hsw_enable_source.
v2: Avoid changing order here to avoid changing behaviour
as suggested by Jani.
v3: Rebased on top of commit d2419ffc10 ("drm/i915: Plumb
crtc_state to PSR enable/disable")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-7-rodrigo.vivi@intel.com
VSC package is decided per eDP spec for psr1 or psr2,
and not per platform, so let's unify it and kill "skl"
func.
v2: Rebased on top of commit d2419ffc10 ("drm/i915: Plumb
crtc_state to PSR enable/disable")
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-6-rodrigo.vivi@intel.com
On HSW+ the real activate of PSR is decided by the source
after certain amount of configured idle frames.
However for the driver perspective where we track psr.active
variable this function here is the actual activate one. So
let's rename it before moving to vfunc with that.
v2: Fix typo on commit message (DK).
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-4-rodrigo.vivi@intel.com
VLV/CHV has a total different PSR implementation than the
other platforms, so let's start moving that to vfuncs.
Let's start with disable_src one.
v2: Rebased on top of commit d2419ffc10 ("drm/i915: Plumb
crtc_state to PSR enable/disable")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-3-rodrigo.vivi@intel.com
We really don't want to setup vfuncs and lock mutexes on
platforms that has no support to PSR.
Also we know what platforms they are so let's do it quietly.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170907230041.22978-2-rodrigo.vivi@intel.com
If we know that we will completely fill a pagetable (i.e. we are
inserting a complete set of 512 pages), we can skip prefilling that PT
with scratch entries. If we have to abort the insertion prior to writing
the real entries, we will teardown the pagetable and remove it from the
page directory (so that we will restart the allocation next time).
We could do similar tricks for the PD and PDP, but the likelihood of a
single insertion covering the entire 512 entries diminishes, as do the
cycle savings. The saving are even greater (relatively) when we are
preallocating page tables for huge pages, as then we never need to fill
the page table.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908181622.17791-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Macro params shall be wrapped into () to avoid unexpected results.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908161130.22424-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Gen7 won't get any new engines, and we already added VCS2 there to just
silence gcc's not handled in switch warnings.
Use a default case instead, otherwise we will need to keep adding extra
cases if changes happen in the future.
v2: Since reaching the default case is impossible, use GEM_BUG_ON (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170830180115.907-1-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Looking at our virtual PCI device, we can see surprising Region 4 and Region 5.
00:10.0 VGA compatible controller: Intel Corporation Sky Lake Integrated Graphics (rev 06) (prog-if 00 [VGA controller])
....
Region 0: Memory at 140000000 (64-bit, non-prefetchable) [size=16M]
Region 2: Memory at 180000000 (64-bit, prefetchable) [size=1G]
Region 4: Memory at <ignored> (32-bit, non-prefetchable)
Region 5: Memory at <ignored> (32-bit, non-prefetchable)
Expansion ROM at febd6000 [disabled] [size=2K]
The fact is that we only implemented BAR0 and BAR2. Surprising Region 4 and
Region 5 are shown because we report their size as 0xffffffff. They should
report size 0 instead.
BTW, the physical GPU has a PIO BAR. GVTg hasn't implemented PIO access, so
we ignored this BAR for vGPU device.
v2: fix BAR size value calculation.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1458032
Signed-off-by: Changbin Du <changbin.du@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
fix the wrong return type and return error once the unknown
command is scanned.
v2:
- separate this error handle from healthy rating code. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
When an error occurs in dispatch_workload, this patch is to do the
proper cleanup and rollback to the original states before the workload
is abandoned.
v2:
- split the mixed several error paths for better review. (Zhenyu)
v3:
- original PTR_ERR(cs) is good and code cleanup. (Zhenyu)
v4:
- reuse the existing i915_add_request for error handling. (Zhenyu)
v5:
- remove the duplicate error handling release_shadow_wa_ctx and
move the engine->context_unpin upper. (Zhenyu)
v6:
- keep the old label "out". (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
When it is failed in shadow_mm, the pin_count should rollback
to the original states before return.
v2:
- split the mixed several error paths for better review. (Zhenyu)
v3:
increase the pincount after shadow success. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
refine the error handling for prepare_execlist_workload to restore to the
original states once error occurs.
only release the shadowed batch buffer and wa ctx when the workload is
completed successfully.
v2:
- split the mixed several error paths for better review. (Zhenyu)
v3:
- handle prepare batch buffer/wa ctx pin errors and
- emulate_schedule_in null issue. (Zhenyu)
v4:
- no need to handle emulate_schedule_in null issue. (Zhenyu)
v5:
- release the shadowed batch buffer and wa ctx only for the
successful workload. (Zhenyu)
v6:
- polish the return style. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
When an error occurs after shadow_indirect_ctx, this patch is to do the
proper cleanup and rollback to the original states for shadowed indirect
context before the workload is abandoned.
v2:
- split the mixed several error paths for better review. (Zhenyu)
v3:
- no return check for clean up functions. (Changbin)
v4:
- expose and reuse the existing release_shadow_wa_ctx. (Zhenyu)
v5:
- move the release function to scheduler.c file. (Zhenyu)
v6:
- move error handling code of intel_gvt_scan_and_shadow_workload
to here. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Currently i915 request structure and shadow ring buffer are allocated
before command scan, so it will have to restore to previous states once
any error happens afterwards in the long dispatch_workload path.
This patch is to introduce a reserved ring buffer created at the beginning
of vGPU initialization. Workload will be coped to this reserved buffer and
be scanned first, the i915 request and shadow ring buffer are only
allocated after the result of scan is successful.
To balance the memory usage and buffer alloc time, the coming bigger ring
buffer will be reallocated and kept until more bigger buffer is coming.
v2:
- use kmalloc for the smaller ring buffer, realloc if required. (Zhenyu)
v3:
- remove the dynamically allocated ring buffer. (Zhenyu)
v4:
- code style polish.
- kfree previous allocated buffer once kmalloc failed. (Zhenyu)
Signed-off-by: fred gao <fred.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
For vfio-pci, if the region support MMAP then it should support both
mmap and normal file access. The user-space is free to choose which is
being used. For qemu, we just need add 'x-no-mmap=on' for vfio-pci
option.
Currently GVTg only support MMAP for BAR2. So GVTg will not work when
user turn on x-no-mmap option.
This patch added file style access for BAR2, aka the GPU aperture. We
map the entire aperture partition of active vGPU to kernel space when
guest driver try to enable PCI Memory Space. Then we redirect the file
RW operation from kvmgt to this mapped area.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1458032
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
For PCI, 64bit bar consumes two BAR registers, but this doesn't mean
both of two BAR are valid. Actually the second BAR is regarded as
reserved in this case. So we shouldn't emulate the second BAR.
Signed-off-by: Changbin Du <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
