A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The tegra_mc_probe_device() symbol is only available when the TEGRA_MC
Kconfig option is enabled. Provide a stub if that's not the case so that
the driver can be compile-tested.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210618111846.1286166-1-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmDDjV4THHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoXVsD/0QgZHiuEH8rU42JtYGB/rjCskWUPen
BOtcrIi+QxJ7m8q4qnRrPIeE8ETjQAB92pWpZE8VQ260Pk/s8NAeIXBbP7I2lKU8
M+TkwvCQ8zZw18q9ZPinqSUHgVsh7Q+7kQggHGZcYpE4rOmlb0oTr9B2EprdSpBl
hVNGtcaJ9Ovqri1ioDi/owUaxYpeJ3L8A++luIv9K8oDUpN7GBw3nV0dMOBvUOBs
nT9iQFEThvo0NRNs4zPNDPLPsLJFwePRDmY9SE4PCreDKo26+VWAamooW8R6iEnU
P7OOfCSZbLqMs8Sfkjrb742sqWX50okFFJQG6aW3BOln3IA5esc9uJ3l2jH6GZP1
21hestxJjK2JuZLv8uMtGHura8do7e4PrYVvxOT6Lp85AXaXA1/uieAWRyh40lcD
d4S4hL3prlfgepj6eUy40MnbLbatsRyQoFYdloZtB+cZb+KxMSV/Lx+j0Y5VyOI/
OpVcTxTxwAZRrVcHTISkUjkxLProY1hQwQP9vexRMIn8SB+ZhgztjHJQuUxa25at
c2Q1aOeGr+h3w1NYpOa+u1tyyKt/Vw92tA84MHaoGoWJg2DGXDAh66HFpiFrmE8q
+n2wc/uyhz1bdS38ky73ibJ6iQ96ucRLxEjCIz+59hdZ57bEYnF+EUJtNdMSyqXg
hGVs5fnWFlw97Q==
=g0AU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
soc/tegra: Changes for v5.14-rc1
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
* tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix Tegra234-only builds
soc/tegra: fuse: Don't return -ENOMEM when allocate lookups failed
soc/tegra: regulators: Support core domain state syncing
soc/tegra: pmc: Add driver state syncing
soc/tegra: pmc: Add core power domain
soc/tegra: fuse: Add stubs needed for compile-testing
soc/tegra: Add devm_tegra_core_dev_init_opp_table()
soc/tegra: Add stub for soc_is_tegra()
soc/tegra: regulators: Bump voltages on system reboot
regulator: core: Add regulator_sync_voltage_rdev()
Link: https://lore.kernel.org/r/20210611164437.3568059-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing stubs that will allow Tegra memory driver to be compile-tested
by kernel build bots.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As on i.MX51 and i.MX53, initialize the SoC ID based on the SoC
compatible string of the board.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
-----BEGIN PGP SIGNATURE-----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=+DV0
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
* tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: enable acpi support in RCPM driver
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
tty: serial: ucc_uart: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: qe: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: guts: fix comment syntax in file
soc: fsl: guts: remove unneeded semicolon
soc: fsl: qe: Use DEFINE_SPINLOCK() for spinlock
soc: fsl: qbman: Delete useless kfree code
soc: fsl: qbman: Ensure device cleanup is run for kexec
Link: https://lore.kernel.org/r/20210409205719.27927-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
-----BEGIN PGP SIGNATURE-----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=bbW2
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: tegra20: mc: Convert to schema
dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
memory: tegra: Print out info-level once per driver probe
memory: tegra20: Protect debug code with a lock
memory: tegra20: Correct comment to MC_STAT registers writes
memory: tegra20: Add debug statistics
memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6ac9b61786.
This commit was required because at that time, ioread/iowrite
functions were sub-optimal on powerpc/32 compared to the
architecture specific in_/out_ IO accessors.
But there are now equivalent since
commit 894fa235eb ("powerpc: inline iomap accessors").
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add debug statistics collection support. The statistics is available
via debugfs in '/sys/kernel/debug/mc/stats', it shows percent of memory
controller utilization for each memory client. This information is
intended to help with debugging of memory performance issues, it already
was proven to be useful by helping to improve memory bandwidth management
of the display driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210319130933.23261-1-digetx@gmail.com
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.
I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.
We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.
We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new PGID that is used not to forward frames anywhere. It is used
by MRP to make sure that MRP Test frames will not reach CPU port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a handful of new RISC-V related patches for this merge window:
* A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may catch
errors in new drivers.
* Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
* NUMA support for RISC-V, which involves making the arm64 code generic.
* Support for kasan on the vmalloc region.
* A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
* Support for allocating ASIDs.
* Preliminary support for kernels larger than 128MiB.
* Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
-----BEGIN PGP SIGNATURE-----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=CutX
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
Add a clock provider driver for the Canaan Kendryte K210 RISC-V SoC.
This new driver with the compatible string "canaan,k210-clk" implements
support for the full clock structure of the K210 SoC. Since it is
required for the correct operation of the SoC, this driver is
selected by default for compilation when the SOC_CANAAN option is
selected.
With this change, the k210-sysctl driver is turned into a simple
platform driver which enables its power bus clock and triggers
populating its child nodes. The sysctl driver retains the SOC early
initialization code, but the implementation now relies on the new
function k210_clk_early_init() provided by the new clk-k210 driver.
The clock structure implemented and many of the coding ideas for the
driver come from the work by Sean Anderson on the K210 support for the
U-Boot project.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Including:
- ARM SMMU and Mediatek updates from Will Deacon:
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance
on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built
independently from IOMMU
- Some tidy-up in IOVA and core code
- Conversion of the AMD IOMMU code to use the generic
IO-page-table framework
- Intel VT-d updates from Lu Baolu:
- Audit capability consistency among different IOMMUs
- Add SATC reporting structure support
- Add iotlb_sync_map callback support
- SDHI Support for Renesas IOMMU driver
- Misc Cleanups and other small improvments
-----BEGIN PGP SIGNATURE-----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=xSX1
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM SMMU and Mediatek updates from Will Deacon:
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU perf driver to be built independently from IOMMU
- Some tidy-up in IOVA and core code
- Conversion of the AMD IOMMU code to use the generic IO-page-table
framework
- Intel VT-d updates from Lu Baolu:
- Audit capability consistency among different IOMMUs
- Add SATC reporting structure support
- Add iotlb_sync_map callback support
- SDHI support for Renesas IOMMU driver
- Misc cleanups and other small improvments
* tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (94 commits)
iommu/amd: Fix performance counter initialization
MAINTAINERS: repair file pattern in MEDIATEK IOMMU DRIVER
iommu/mediatek: Fix error code in probe()
iommu/mediatek: Fix unsigned domid comparison with less than zero
iommu/vt-d: Parse SATC reporting structure
iommu/vt-d: Add new enum value and structure for SATC
iommu/vt-d: Add iotlb_sync_map callback
iommu/vt-d: Move capability check code to cap_audit files
iommu/vt-d: Audit IOMMU Capabilities and add helper functions
iommu/vt-d: Fix 'physical' typos
iommu: Properly pass gfp_t in _iommu_map() to avoid atomic sleeping
iommu/vt-d: Fix compile error [-Werror=implicit-function-declaration]
driver/perf: Remove ARM_SMMU_V3_PMU dependency on ARM_SMMU_V3
MAINTAINERS: Add entry for MediaTek IOMMU
iommu/mediatek: Add mt8192 support
iommu/mediatek: Remove unnecessary check in attach_device
iommu/mediatek: Support master use iova over 32bit
iommu/mediatek: Add iova reserved function
iommu/mediatek: Support for multi domains
iommu/mediatek: Add get_domain_id from dev->dma_range_map
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released()
function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not
belong into any other subsystem, most of them living in
drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=I2Zn
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.
We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.
-----BEGIN PGP SIGNATURE-----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=rWBX
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for 5.12
The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.
* tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ocmem: don't return NULL in of_get_ocmem
soc: qcom: socinfo: Remove unwanted le32_to_cpu()
soc: qcom: aoss: Add SM8350 compatible
drivers: soc: qcom: rpmpd: Add msm8994 RPM Power Domains
soc: qcom: socinfo: Fix an off by one in qcom_show_pmic_model()
soc: qcom: socinfo: Fix off-by-one array index bounds check
soc: qcom: socinfo: Add MDM9607 IDs
soc: qcom: socinfo: Add SoC IDs for APQ/MSM8998
soc: qcom: socinfo: Add SoC IDs for 630 family
soc: qcom: socinfo: Open read access to all for debugfs
soc: qcom: socinfo: add info from PMIC models array
soc: qcom: socinfo: add several PMIC IDs
soc: qcom: socinfo: add qrb5165 SoC ID
soc: qcom: rpmh: Remove serialization of TCS commands
soc: qcom: smem: use %*ph to print small buffer
dt-bindings: soc: qcom: convert qcom,smem bindings to yaml
drivers: qcom: rpmh-rsc: Do not read back the register write on trigger
soc: qcom: llcc-qcom: Add support for SM8250 SoC
soc: qcom: llcc-qcom: Extract major hardware version
dt-bindings: msm: Add LLCC for SM8250
Link: https://lore.kernel.org/r/20210204052258.388890-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
please pull the following:
- Rafal adds support for the Power Management Bus (PMB) which is used in
a variety of DSL/Cable modem/STB SoCs with a primary target being the
4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
get the chip identification (family and revision) to permit the
Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
- Florian removes an unused function and its header
-----BEGIN PGP SIGNATURE-----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=43Gr
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoCs drivers changes for 5.12,
please pull the following:
- Rafal adds support for the Power Management Bus (PMB) which is used in
a variety of DSL/Cable modem/STB SoCs with a primary target being the
4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
get the chip identification (family and revision) to permit the
Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
- Florian removes an unused function and its header
* tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Remove soc_is_brcmstb()
soc: bcm: brcmstb: add stubs for getting platform IDs
soc: bcm: add PM driver for Broadcom's PMB
dt-bindings: power: document Broadcom's PMB binding
Link: https://lore.kernel.org/r/20210131221721.685974-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.
-----BEGIN PGP SIGNATURE-----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=S32T
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.12
1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.
* tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: mtk-smi: Allow building as module
memory: ti-aemif: Drop child node when jumping out loop
memory: mtk-smi: Use platform_register_drivers
memory: renesas-rpc-if: Add RZ/G2 to Kconfig description
dt-bindings: memory: renesas,rpc-if: Add support for RZ/G2 Series
memory: emif: Use DEFINE_SPINLOCK() for spinlock
memory: mtk-smi: Fix PM usage counter unbalance in mtk_smi ops
Link: https://lore.kernel.org/r/20210131180109.11510-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmAYD/QQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNLZjCACBK2bCmkVJfs39YeeMhHWVRyiiMpIuCvja
7WuIqeXnbtAg19hkwPqns+XYeTTnoeo/aSZUS9z8DIDUqADMES+1UUMfVf2mfL3A
VD1pGRtQezYS+rDOc5dL9m1CcJ2RRY5tfQEjK8Fnm5CItvylNXbURH1nfu1tMVW7
fn1tMNKCTnY7FkABttKyR4a1XIyFX+fPdSrqd5PjQ7D6rK2ZYrorMf55WpmQEfFu
3er4F3Xz8nJeTvswPUMNB3ibvcdICM9VcSwFHpElTq2dbHUDDz3uFQwyiXrutEmb
Xz4UGabjS/ZEPaty6y7VxdYEbD4Q2dzii57jKKtV49N36iCvkSR2
=5KXT
-----END PGP SIGNATURE-----
Merge tag 'arm-smmu-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into arm/smmu
Arm SMMU updates for 5.12
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
After extending v7s, our pagetable already support iova reach
16GB(34bit). the master got the iova via dma_alloc_attrs may reach
34bits, but its HW register still is 32bit. then how to set the
bit32/bit33 iova? this depend on a SMI larb setting(bank_sel).
we separate whole 16GB iova to four banks:
bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G;
The bank number is (iova >> 32).
We will preassign which bank the larbs belong to. currently we don't
have a interface for master to adjust its bank number.
Each a bank is a iova_region which is a independent iommu-domain.
the iova range for each iommu-domain can't cross 4G.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> #for memory part
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-31-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Use the common memory header(larb-port) in the source code.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-9-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Unlike sja1105, the only other user of the software-defined tag_8021q.c
tagger format, the implementation we choose for the Felix DSA switch
driver preserves full functionality under a vlan_filtering bridge
(i.e. IP termination works through the DSA user ports under all
circumstances).
The tag_8021q protocol just wants:
- Identifying the ingress switch port based on the RX VLAN ID, as seen
by the CPU. We achieve this by using the TCAM engines (which are also
used for tc-flower offload) to push the RX VLAN as a second, outer
tag, on egress towards the CPU port.
- Steering traffic injected into the switch from the network stack
towards the correct front port based on the TX VLAN, and consuming
(popping) that header on the switch's egress.
A tc-flower pseudocode of the static configuration done by the driver
would look like this:
$ tc qdisc add dev <cpu-port> clsact
$ for eth in swp0 swp1 swp2 swp3; do \
tc filter add dev <cpu-port> egress flower indev ${eth} \
action vlan push id <rxvlan> protocol 802.1ad; \
tc filter add dev <cpu-port> ingress protocol 802.1Q flower
vlan_id <txvlan> action vlan pop \
action mirred egress redirect dev ${eth}; \
done
but of course since DSA does not register network interfaces for the CPU
port, this configuration would be impossible for the user to do. Also,
due to the same reason, it is impossible for the user to inadvertently
delete these rules using tc. These rules do not collide in any way with
tc-flower, they just consume some TCAM space, which is something we can
live with.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.
Unfortunately, a lesson learned in commit 69df578c5f ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.
The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.
There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will be adding some private VCAP filters that should not interfere in
any way with the filters added using tc-flower. So we need to allocate
some IDs which will not be used by tc.
Currently ocelot uses an u32 id derived from the flow cookie, which in
itself is an unsigned long. This is a problem in itself, since on 64 bit
systems, sizeof(unsigned long)=8, so the driver is already truncating
these.
Create a struct ocelot_vcap_id which contains the full unsigned long
cookie from tc, as well as a boolean that is supposed to namespace the
filters added by tc with the ones that aren't.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix driver will need to preinstall some VCAP filters for its
tag_8021q implementation (outside of the tc-flower offload logic), so
these need to be exported to the common includes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have no in tree or out of tree users of this function, remove it and
the header providing its prototype.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for building the SMI driver as module. Switch MTK_SMI to
tristate, and add module_exit/module_license.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210126060055.11050-1-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bd_mem_part member of ucc_geth_info always has the value
MEM_PART_SYSTEM, and AFAICT, there has never been any code setting it
to any other value. Moreover, muram is a somewhat precious resource,
so there's no point using that when normal memory serves just as well.
Apart from removing a lot of dead code, this is also motivated by
wanting to clean up the "store result from kmalloc() in a u32" mess.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper that takes a virtual address rather than the muram
offset. This will be used in a couple of places to avoid having to
store both the offset and the virtual address, as well as removing
NULL checks from the callers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow passing const-qualified pointers without requiring a cast in the
caller.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).
The following definitions can be made:
SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
# have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
# have one of these.
Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR
Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.
devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
size 129840 thtype static
Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).
Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:
devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
pool $POOL_ING th 1000
The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.
Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:
for tc in {0..7}; do
devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
type ingress pool $POOL_ING \
th 3000
done
The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink integration into the mscc_ocelot switchdev driver. All
physical ports (i.e. the unused ones as well) except the CPU port module
at ocelot->num_phys_ports are registered with devlink, and that requires
keeping the devlink_port structure outside struct ocelot_port_private,
since the latter has a 1:1 mapping with a struct net_device (which does
not exist for unused ports).
Since we use devlink_port_type_eth_set to link the devlink port to the
net_device, we can as well remove the .ndo_get_phys_port_name and
.ndo_get_port_parent_id implementations, since devlink takes care of
retrieving the port name and number automatically, once
.ndo_get_devlink_port is implemented.
Note that the felix DSA driver is already integrated with devlink by
default, since that is a thing that the DSA core takes care of. This is
the reason why these devlink stubs were put in ocelot_net.c and not in
the common library. It is also the reason why ocelot::devlink is a
pointer and not a full structure embedded inside struct ocelot: because
the mscc_ocelot driver allocates that by itself (as the container of
struct ocelot, in fact), but in the case of felix, it is DSA who
allocates the devlink, and felix just propagates the pointer towards
struct ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should be moving anything that isn't DSA-specific or SoC-specific out
of the felix DSA driver, and into the common mscc_ocelot switch library.
The number of traffic classes is one of the aspects that is common
between all ocelot switches, so it belongs in the library.
This patch also makes seville use 8 TX queues, and therefore enables
prioritization via the QOS_CLASS field in the NPI injection header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We'll need to read back the watermark thresholds and occupancy from
hardware (for devlink-sb integration), not only to write them as we did
so far in ocelot_port_set_maxlen. So introduce 2 new functions in struct
ocelot_ops, similar to wm_enc, and implement them for the 3 supported
mscc_ocelot switches.
Remove the INUSE and MAXUSE unpacking helpers for the QSYS_RES_STAT
register, because that doesn't scale with the number of switches that
mscc_ocelot supports now. They have different bit widths for the
watermarks, and we need function pointers to abstract that difference
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.
The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.
Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.
*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the header file include/soc/canaan/k210-sysctl.h to have a
common definition of the Canaan Kendryte K210 SoC system controller
registers. Simplify the k210 system controller driver code by removing
unused register bits definition. The MAINTAINERS file is updated,
adding the entry "CANAAN/KENDRYTE K210 SOC SYSTEM CONTROLLER DRIVER"
with myself listed as maintainer for this driver.
This is a preparatory patch for introducing the K210 clock driver. No
functional changes are introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.
Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.
Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add modularization support to the Tegra124 EMC driver, which now can be
compiled as a loadable kernel module.
Note that EMC clock must be registered at clk-init time, otherwise PLLM
will be disabled as unused clock at boot time if EMC driver is compiled
as a module. Hence add a prepare/complete callbacks. similarly to what is
done for the Tegra20/30 EMC drivers.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201228154920.18846-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Currently ocelot_set_rx_mode calls ocelot_mact_learn directly, which has
a very nice ocelot_mact_wait_for_completion at the end. Introduced in
commit 639c1b2625 ("net: mscc: ocelot: Register poll timeout should be
wall time not attempts"), this function uses readx_poll_timeout which
triggers a lot of lockdep warnings and is also dangerous to use from
atomic context, potentially leading to lockups and panics.
Steen Hegelund added a poll timeout of 100 ms for checking the MAC
table, a duration which is clearly absurd to poll in atomic context.
So we need to defer the MAC table access to process context, which we do
via a dynamically allocated workqueue which contains all there is to
know about the MAC table operation it has to do.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212191612.222019-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.
So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.
The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.
And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
MC6_DATA = 61,
MC6_CTRL = 61,
MC4_DATA = 60,
MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.
Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct typo in a stub of devm_tegra_memory_controller_get() to fix a
non-ARM kernel compile-testing.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201111011456.7875-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add common SoC-agnostic ICC framework which turns Tegra Memory Controller
into a memory interconnection provider. This allows us to use interconnect
API for tuning of memory configurations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-33-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Multiple Tegra drivers need to retrieve Memory Controller and there is
duplication of the retrieval code among the drivers.
Add new devm_tegra_memory_controller_get() helper to remove the code's
duplication and to fix put_device() which was missed in the duplicated
code. Make EMC drivers to use the new helper.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-29-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Drivers that use tegra_sku_info and have COMPILE_TEST are failing to be
build due to the missing stub for tegra_sku_info.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we are checking in some places whether the port has a native
VLAN on egress or not, by comparing the ocelot_port->vid value with zero.
That works, because VID 0 can never be a native VLAN configured by the
bridge, but now we want to make similar checks for the pvid. That won't
work, because there are cases when we do have the pvid set to 0 (not by
the bridge, by ourselves, but still.. it's confusing). And we can't
encode a negative value into an u16, so add a bool to the structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is one main difference in mscc_ocelot between IP multicast and L2
multicast. With IP multicast, destination ports are encoded into the
upper bytes of the multicast MAC address. Example: to deliver the
address 01:00:5E:11:22:33 to ports 3, 8, and 9, one would need to
program the address of 00:03:08:11:22:33 into hardware. Whereas for L2
multicast, the MAC table entry points to a Port Group ID (PGID), and
that PGID contains the port mask that the packet will be forwarded to.
As to why it is this way, no clue. My guess is that not all port
combinations can be supported simultaneously with the limited number of
PGIDs, and this was somehow an issue for IP multicast but not for L2
multicast. Anyway.
Prior to this change, the raw L2 multicast code was bogus, due to the
fact that there wasn't really any way to test it using the bridge code.
There were 2 issues:
- A multicast PGID was allocated for each MDB entry, but it wasn't in
fact programmed to hardware. It was dummy.
- In fact we don't want to reserve a multicast PGID for every single MDB
entry. That would be odd because we can only have ~60 PGIDs, but
thousands of MDB entries. So instead, we want to reserve a multicast
PGID for every single port combination for multicast traffic. And
since we can have 2 (or more) MDB entries delivered to the same port
group (and therefore PGID), we need to reference-count the PGIDs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:
Basic classification -> VCAP IS1 -> VCAP IS2
Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).
Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.
This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.
There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.
For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.
In plain ocelot_read, the target is encoded into the register enum
itself:
u16 target = reg >> TARGET_OFFSET;
For the VCAPs, the registers are currently defined like this:
enum ocelot_reg {
[...]
S2_CORE_UPDATE_CTRL = S2 << TARGET_OFFSET,
S2_CORE_MV_CFG,
S2_CACHE_ENTRY_DAT,
S2_CACHE_MASK_DAT,
S2_CACHE_ACTION_DAT,
S2_CACHE_CNT_DAT,
S2_CACHE_TG_DAT,
[...]
};
which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).
So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.
The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compile warnings from the -Wpacked-not-aligned option.
In file included from ../drivers/crypto/caam/qi.c:12:
../include/soc/fsl/qman.h:259:1: warning: alignment 1 of ‘struct qm_dqrr_entry’ is less than 8 [-Wpacked-not-aligned]
} __packed;
^
../include/soc/fsl/qman.h:292:2: warning: alignment 1 of ‘struct <anonymous>’ is less than 8 [-Wpacked-not-aligned]
} __packed ern;
^
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
It is a good measure to ensure correctness if the structures that are
meant to remain constant are only processed by functions that thake
constant arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for FUSE block found on the Tegra234 SoC, which is largely
similar to the IP found on previous generations.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function can be used by drivers to determine whether code is
running on silicon or on a simulation platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function extracts the PRE_SI_PLATFORM field from the HIDREV
register and can be used to determine which platform the kernel runs on
(silicon, simulation, ...). Note that while only Tegra194 and later
define this field, it should be safe to call this on prior generations
as well since this field should read as 0, indicating silicon.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.
The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
- copy AUX_IENABLE from arch/arc header
- move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This reverts commit fbbc5ff3f7.
The vl805 init routine has moved into drivers/reset/reset-raspberrypi.c
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-9-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20200726110117.16346-1-grandmaster@al2klimov.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
framework we just have some minor tweaks and a debugfs feature, so not much to
see there. The driver updates are fairly well split between AT91 and Qualcomm
clk support. Adding those two drivers together equals about 50% of the
diffstat. Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks. See below for some more highlights.
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only consider
clocks that were enabled at boot time
-----BEGIN PGP SIGNATURE-----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=QLRg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It looks like a smaller batch of clk updates this time around.
In the core framework we just have some minor tweaks and a debugfs
feature, so not much to see there. The driver updates are fairly well
split between AT91 and Qualcomm clk support. Adding those two drivers
together equals about 50% of the diffstat.
Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks.
Highlights:
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only
consider clocks that were enabled at boot time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
clk: <linux/clk-provider.h>: drop a duplicated word
clk: renesas: cpg-mssr: Add r8a774e1 support
dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
clk: Drop duplicate selection in Kconfig
clk: qcom: smd: Add support for MSM8992/4 rpm clocks
clk: qcom: ipq8074: Add missing clocks for pcie
dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
Replace HTTP links with HTTPS ones: Common CLK framework
clk: qcom: Add CPU clock driver for msm8996
dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
soc: qcom: Separate kryo l2 accessors from PMU driver
clk: meson: meson8b: add the vclk2_en gate clock
clk: meson: meson8b: add the vclk_en gate clock
clk: qcom: Fix return value check in apss_ipq6018_probe()
clk: bcm: dvp: Add missing module informations
clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
...
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
=DXTp
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
-----BEGIN PGP SIGNATURE-----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=Os4F
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.9
For RPMh this fixes an issue where ktime was used during suspend, allows
the driver to be used on ARM targets and some minor cleanups.
It adds support for the latest format version in the socinfo driver and
adds identifiers for SM8250 and SDM630.
SMD-RPM gains compatibles for MSM8994 and MSM8936 and the Qualcomm SCM
gains compatibles MSM8994 and IPQ8074.
The GENI core code gains interconnect path voting and performance level
support, with subsequent patches integrating this with the SPI, I2C,
UART and QSPI drivers.
Following this the KGDB support for the GENI serial driver is improved,
the performance related to chip-select is improved for SPI and QSPI.
* tag 'qcom-drivers-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
soc: qcom: geni: Fix NULL pointer dereference
tty: serial: qcom-geni-serial: Drop the icc bw votes in suspend for console
serial: qcom_geni_serial: Always use 4 bytes per TX FIFO word
serial: qcom_geni_serial: Make kgdb work even if UART isn't console
spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
spi: spi-geni-qcom: Set the clock properly at runtime resume
spi: spi-geni-qcom: Avoid clock setting if not needed
spi: spi-qcom-qspi: Set an autosuspend delay of 250 ms
spi: spi-qcom-qspi: Avoid clock setting if not needed
spi: spi-qcom-qspi: Use OPP API to set clk/perf state
firmware: qcom_scm: Add msm8994 compatible
firmware: qcom_scm: Fix legacy convention SCM accessors
<linux/of.h>: add stub for of_get_next_parent() to fix qcom build error
dt-bindings: firmware: qcom: Add compatible for IPQ8074 SoC
spi: spi-geni-qcom: Use OPP API to set clk/perf state
tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state
spi: spi-qcom-qspi: Add interconnect support
spi: spi-geni-qcom: Add interconnect support
spi: spi-geni-qcom: Combine the clock setting code
tty: serial: qcom_geni_serial: Add interconnect support
...
Link: https://lore.kernel.org/r/20200721044812.3429652-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds missing SoC IDs for Tegra186 and Tegra194 and fixes a typo in
a warning message.
-----BEGIN PGP SIGNATURE-----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=B2af
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.9-rc1
This adds missing SoC IDs for Tegra186 and Tegra194 and fixes a typo in
a warning message.
* tag 'tegra-for-5.9-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix typo in APB MISC warning
soc/tegra: fuse: Add Tegra186 and Tegra194 SoC IDs
Link: https://lore.kernel.org/r/20200717161300.1661002-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SoC IDs for these generations had never been defined. Do so now.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the BPMP ABI to align with the the latest version.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for retrieving BPMP debug information via in-band messaging
as opposed to using shared-memory which older BPMP firmware used. Note
that it is possible to detect at runtime whether the BPMP firmware being
used supports the in-band messaging for retrieving the debug
informaation. Therefore, if the BPMP firmware supports the in-band
messaging for debug use this and otherwise fall-back to using shared
memory.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some atmel socs have extra tcb capabilities that allow using a generic
clock source or enabling a quadrature decoder.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200710230813.1005150-5-alexandre.belloni@bootlin.com
The driver provides kernel level API for other drivers
to access the MSM8996 L2 cache registers.
Separating the L2 access code from the PMU driver and
making it public to allow other drivers use it.
The accesses must be separated with a single spinlock,
maintained in this driver.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593766185-16346-2-git-send-email-loic.poulain@linaro.org
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current iterators are impossible to understand at first glance
without switching back and forth between the definitions and their
actual use in the for loops.
So introduce some convenience names to help readability.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rpmh_invalidate() always returns success. Update its
return type to void.
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1592485553-29163-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.
Let's rename the structures and functions to something more generic, so
that VCAP IS1 structures (which would otherwise have to be called
Ingress Classification Entries) can reuse the same code without
confusion.
Some renaming that was done:
struct ocelot_ace_rule -> struct ocelot_vcap_filter
struct ocelot_acl_block -> struct ocelot_vcap_block
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_vlan -> struct ocelot_vcap_key_vlan
enum ocelot_ace_action -> enum ocelot_vcap_action
struct ocelot_ace_stats -> struct ocelot_vcap_stats
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_frame_* -> struct ocelot_vcap_key_*
No functional change is intended.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
- Add soc device support for Vybrid/VF platform.
- Move the i.MX soc device registration code from mach-imx to
drivers/soc/imx for possible future consolidation with i.MX8 code.
- A small fixup to make pcm970_sja1000_platform_data static.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IflgUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5Tswf+Id6DM109IHuZxhPWNB5SKEkVa1cr
v7u7GeT/REqnsVCoFgC0kYIVlOj6nm7F8wwrHziiocvryUV8KPiENG3zMCVzJfLz
+xkZxIYEuMeLoJjWOz3HeR5bp8G5GeL8sGt2D5OrMh1EUHYTZdnf4/nESvCMJb41
rOaBRHuhhR1/Dv8qwCkXU9zep/jwlVXf+r6pC5pQNGmUpUGC2VFc7rDYkODS8Jo4
MfNx5S+HHk2Jabei+6fKEsVG1x7E3lv3ky/ZdVWhjtgy19I32E+o4Cr+UQqegIen
N4V/Uya6KejSvhaHDf6Pz2TjqTkXxlWSQ0Lu2I7pDMWdU5Upf0iLqbV1rQ==
=MC2F
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/soc
i.MX SoC changes for 5.8:
- Add soc device support for Vybrid/VF platform.
- Move the i.MX soc device registration code from mach-imx to
drivers/soc/imx for possible future consolidation with i.MX8 code.
- A small fixup to make pcm970_sja1000_platform_data static.
* tag 'imx-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
ARM: vf610: report soc info via soc device
Link: https://lore.kernel.org/r/20200523032516.11016-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a large set of cleanups, bug fixes, general improvements
and documentation fixes for the RPMH driver. It adds a debugfs mechanism
for inspecting Command DB. Socinfo got the "soc_id" attribute defines
and definitions for a various variants of MSM8939.
RPMH, RPMPD and RPMHPD where made possible to build as modules, but RPMH
had to be reverted due to a compilation issue when tracing is enabled.
RPMHPD gained power-domains for the SM8250 voltage corners.
The SCM driver gained fixes for two build warnings and the SMP2P had an
unnecessary error print removed.
-----BEGIN PGP SIGNATURE-----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=tkhb
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.8
This contains a large set of cleanups, bug fixes, general improvements
and documentation fixes for the RPMH driver. It adds a debugfs mechanism
for inspecting Command DB. Socinfo got the "soc_id" attribute defines
and definitions for a various variants of MSM8939.
RPMH, RPMPD and RPMHPD where made possible to build as modules, but RPMH
had to be reverted due to a compilation issue when tracing is enabled.
RPMHPD gained power-domains for the SM8250 voltage corners.
The SCM driver gained fixes for two build warnings and the SMP2P had an
unnecessary error print removed.
* tag 'qcom-drivers-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (42 commits)
Revert "soc: qcom: rpmh: Allow RPMH driver to be loaded as a module"
soc: qcom: rpmh-rsc: Remove the pm_lock
soc: qcom: rpmh-rsc: Simplify locking by eliminating the per-TCS lock
kernel/cpu_pm: Fix uninitted local in cpu_pm
soc: qcom: rpmh-rsc: We aren't notified of our own failure w/ NOTIFY_BAD
soc: qcom: rpmh-rsc: Correctly ignore CPU_CLUSTER_PM notifications
firmware: qcom_scm-legacy: Replace zero-length array with flexible-array
soc: qcom: rpmh-rsc: Timeout after 1 second in write_tcs_reg_sync()
soc: qcom: rpmh-rsc: Factor "tcs_reg_addr" and "tcs_cmd_addr" calculation
soc: qcom: socinfo: add msm8936/39 and apq8036/39 soc ids
soc: qcom: aoss: Add SM8250 compatible
soc: qcom: pdr: Remove impossible error condition
soc: qcom: rpmh: Dirt can only make you dirtier, not cleaner
soc: qcom: rpmhpd: Add SM8250 power domains
firmware: qcom_scm: fix bogous abuse of dma-direct internals
dt-bindings: soc: qcom: apr: Use generic node names for APR services
firmware: qcom_scm: Remove unneeded conversion to bool
soc: qcom: cmd-db: Properly endian swap the slv_id for debugfs
soc: qcom: cmd-db: Use 5 digits for printing address
soc: qcom: cmd-db: Cast sizeof() to int to silence field width warning
...
Link: https://lore.kernel.org/r/20200519052533.1250024-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current codebase makes use of one-element arrays in the following
form:
struct something {
int length;
u8 data[1];
};
struct something *instance;
instance = kmalloc(sizeof(*instance) + size, GFP_KERNEL);
instance->length = size;
memcpy(instance->data, source, size);
but the preferred mechanism to declare variable-length types such as
these ones is a flexible array member[1][2], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on. So, replace
the one-element array with a flexible-array member.
Also, make use of the new struct_size() helper to properly calculate the
size of struct qe_firmware.
This issue was found with the help of Coccinelle and, audited and fixed
_manually_.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The soc device register code will be moved to drivers/soc/imx/,
the code needs the cpu type definitions. So let's move the cpu
type definitions to a header.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Raspberry Pi 4 gets its USB functionality from VL805, a PCIe chip
that implements xHCI. After a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
co-processor, VideoCore. RPi4's VideoCore OS contains both the non public
firmware load logic and the VL805 firmware blob. The function this patch
introduces triggers the aforementioned process.
Link: https://lore.kernel.org/r/20200505161318.26200-3-nsaenzjulienne@suse.de
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The property is needed in order to trigger VL805's firmware load. Note
that gap between the property introduced and the previous one is due to
the properties not being defined.
Link: https://lore.kernel.org/r/20200505161318.26200-2-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I found
after restarting my randconfig build testing that had been dormant for
a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=K1jH
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I
found after restarting my randconfig build testing that had been
dormant for a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: imx8: select SOC_BUS
soc: tegra: fix tegra_pmc_get_suspend_mode definition
soc: fsl: dpio: avoid stack usage warning
soc: fsl: dpio: fix incorrect pointer conversions
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: bcm283x: Disable dsi0 node
firmware: xilinx: make firmware_debugfs_root static
drivers: soc: xilinx: fix firmware driver Kconfig dependency
ARM: dts: bcm283x: Add cells encoding format to firmware bus
ARM: dts: OMAP3: disable RNG on N950/N9
Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.
Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, the function is not defined,
causing a link failure:
arm-linux-gnueabi-ld: drivers/cpuidle/cpuidle-tegra.o: in function `tegra_cpuidle_probe':
cpuidle-tegra.c:(.text+0x24): undefined reference to `tegra_pmc_get_suspend_mode'
Change the #ifdef check according to the definition.
Fixes: 382ac8e22b ("cpuidle: tegra: Disable CC6 state if LP2 unavailable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_QCOM_COMMAND_DB=n the following compilation errors will be
seen. Fix this by including the appropriate linux headers.
./include/soc/qcom/cmd-db.h: In function ‘cmd_db_read_aux_data’:
./include/soc/qcom/cmd-db.h: error: implicit declaration of function ‘ERR_PTR’;
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200227125615.4727-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including
cpuidle, pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl6EaLsACgkQmmx57+YA
GNkg/Q/9EmLGT/bznqi6P/8V75qPY6j4swife5HlI43EdCEyN+iME1w1rFfrNilf
A/QyXzxhYgUZoyIt7K4qjWc8fPNlJZ8X10UqeEftQFxi82cmX2+OaT2fy6OdHVRJ
SAGb1pw7463TQ6LKA7LC7rztFjahsjnE/9szlgXQT4v5OzayGyxd3OKy2Q1zASEi
rwN+85Lh+xJvWhhenPKVvs2Dei+up8Y9uyPfJkj2QudCB+zx5k5stkk4EiQLBd1W
SHzhijbSU3MrAUz2Cnp9Qa+86DdGPvFPfpzQy3pSYU9nNrC0aKpS8YmHT99SIWVN
6R1YJF7Htmui5I9+O0baejJMEqvzGUysqe+rQdCofD7ooVKWU7WKYj5HxZxyBCEN
dvlN3KRmS6l5KLsZARSxuBUw2MPTgjsxczZ84NKMLj8czw6yXyrePZ1RWiEZ4HIu
4GiFNLYSMmAynD/dLuC9USDsjlPsQKnQ3e8hDf3a6oK5OHUIkr3uvguhqWa5WJsi
cy2DUeWJkXgJDhlxcfr8MiPpPJRo3N/8O8PYci8dkdDFRs32j/5Qf22vywDdUHaZ
I9Pl+VOGOSGiqRc9gmay6DNXpJusfuv72omrz4rL4kGMahpk0LeV5w+a9TdrkreY
sLM67wtshOjOVMc/ebQ5Q8RR17Go+MFK+Co9Yc1ybbQ6lkSzeuY=
=UTk1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes unify CPU idle support for Tegra20, Tegra30 and Tegra114.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl5rthATHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoZsmD/9qN5NeerI3PxQxDXYljyAJdhXwkRrV
Wliy4BXjMFxwfML1EH2oPBLk+UA8LLhzA3Ai+6qFj/6H+RQcOywdOgyg5913beW9
q0WmPHyaQig7cAAOkI6ke6md0oLmx4nMrS8oX5Ofjd3tfUqo+Y9JT/cvqeiDI7UH
c6/HJy9RaUctDvd7KYCSiH74ZRVjYP0xnbc+Q/uue6Nl0Ka/tbxEFmk/Q6br2K0c
SJXqOroRXongO8WG1w+fQ/MpzluWXArTJmQR8lB38slYhUDa1wL4QRerwtInlffJ
hp/jp1xQ4zx7j5xnvMulj6jC25Pzm69SMpTT4amY+bs33KIqmrdeaCAGmG/70ZoS
dGbdKyiAgpGl8jDbt7wVo+WtQRPGwoJa+Xh+z6H137R6ed59DYgv2f+t5GHwHq9J
iQvWcI9V6SjS9G5caPCE8X5ZdLgCzD4w1Q10vxLTryFuaUJog+13BtfmI34RJAR7
YZ5V9CI+eooHcwiit0aL2IrgA6c9UVrpNR15dxig7KMkJgeY1mngniJ8zqNdjMN8
ZvmaXCNuJdVTAX7QSB0PA1Wg8XI5KN7OzTyE26C3o4x1vI2Z62SPDkaZRsTPJR/R
jRixb5bYmdIWa3HeVkeDziAjP/lx5e59j35QpHPo2XQo5wz82Vc4PEIqqsgDp4KH
yiVXVaXys3n3Ug==
=u9vo
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
cpuidle: tegra: Changes for v5.7-rc1
These changes unify CPU idle support for Tegra20, Tegra30 and Tegra114.
* tag 'tegra-for-5.7-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
Link: https://lore.kernel.org/r/20200313165848.2915133-9-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These patches a preparatory work to move the CPU idle drivers into
drivers/cpuidle.
-----BEGIN PGP SIGNATURE-----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=nOBN
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-arm-core' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
ARM: tegra: Core changes for v5.7-rc1
These patches a preparatory work to move the CPU idle drivers into
drivers/cpuidle.
* tag 'tegra-for-5.7-arm-core' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
ARM: tegra: Rename some of the newly exposed PM functions
ARM: tegra: Expose PM functions required for new cpuidle driver
ARM: tegra: Propagate error from tegra_idle_lp2_last()
ARM: tegra: Change tegra_set_cpu_in_lp2() type to void
ARM: tegra: Remove pen-locking from cpuidle-tegra20
ARM: tegra: Add tegra_pm_park_secondary_cpu()
ARM: tegra: Compile sleep-tegra20/30.S unconditionally
Link: https://lore.kernel.org/r/20200313165848.2915133-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The driver's code is refactored in a way that will make it easy to
support Tegra30/114/124 SoCs by this unified driver later on. The
current functionality is equal to the old Tegra20 driver, only the
code's structure changed a tad. This is also a proper platform driver
now.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename some of the recently exposed PM functions, prefixing them with
"tegra_pm_" in order to make the naming of the PM functions consistent.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The upcoming unified CPUIDLE driver will be added to the drivers/cpuidle/
directory and it will require all these exposed Tegra PM-core functions.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: fixup missing include rename]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the firmware header to support uninitialization of UPHY PLL
when the PCIe controller is operating in endpoint mode and host cuts
the PCIe reference clock.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.
Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.
Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.
Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in. So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.
Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).
So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.
Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].
On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.
Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.
So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).
So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
but no MAC address whitelisted)
So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.
[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.
The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.
The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:
- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
Key Length) of each possible key field. The offset of each field is
defined as the sum between the offset and the sum of the previous
field.
- A set of accessors on top of vcap_key_set for shorter (aka less
typing) access to the HKO and HKL of each key field.
Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.
The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).
But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.
So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.
This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.
Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.
And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update of QMAN the interface to enqueue frame. We now support multiple
enqueue (qbman_swp_enqueue_multiple) and multiple enqueue with
a table of descriptor (qbman_swp_enqueue_multiple_desc).
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Acked-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
rpmh_flush() was exported with the idea that an external entity
operation during CPU idle would know when to flush the sleep and wake
TCS. Since, this is not the case when defining a power domain for the
RSC. Remove the function export and instead allow the function to be
called internally.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1580736940-6985-3-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Since the Felix DSA driver is implementing its own PHYLINK instance due
to SoC differences, it needs access to the few registers that are
common, mainly for flow control.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot switchdev driver and the Felix DSA one need it for different
reasons. Felix (or at least the VSC9959 instantiation in NXP LS1028A) is
integrated with the traditional NXP Layerscape PCS design which does not
support runtime configuration of SerDes protocol. So it needs to
pre-validate the phy-mode from the device tree and prevent PHYLINK from
attempting to change it. For this, it needs to cache it in a private
variable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, change the
ucc_fast_[tr]x_virtual_fifo_base_offset members to s32 and use an
ordinary check-for-negative. Also, this avoids treating 0 as "this
cannot have been returned from qe_muram_alloc() so don't free it".
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When trying to build this for a 64-bit platform, one gets warnings
from using IS_ERR_VALUE on something which is not sizeof(long).
Instead, change the various *_offset fields to store a signed integer,
and simply check for a negative return from qe_muram_alloc(). Since
qe_muram_free() now accepts and ignores a negative argument, we only
need to make sure these fields are initialized with -1, and we can
just unconditionally call qe_muram_free() in ucc_slow_free().
Note that the error case for us_pram_offset failed to set that field
to 0 (which, as noted earlier, is anyway a bogus sentinel value).
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Nobody uses the return value from cpm_muram_free, and functions that
free resources usually return void. One could imagine a use for a "how
much have I allocated" a la ksize(), but knowing how much one had
access to after the fact is useless.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
