The AHB clock on sun5i and sun7i are muxable divider clocks.
Use a factors clock to support them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB controller/phy clocks and reset controls are in a separate
address block, unlike previous SoCs where they were in the clock
controller. Also, access to the address block is controlled by a
clock gate to AHB.
Add support for resets requiring a clock to be enabled when
asserting/deasserting the reset controls, and add the sun9i USB
clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.
This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module 0 style clocks, or storage module clocks as named in the
official SDK, are almost the same as the module 0 clocks on earlier
Allwinner SoCs. The only difference is wider mux register bits.
As with earlier Allwinner SoCs, mmc module clocks are a special case
of mod0 clocks, with phase controls for 2 child clocks, output and
sample.
This patch adds support for both.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Instead of having three different clocks for the main MMC clock and the two
phase sub-clocks, which involved having three different drivers sharing the
same register, rework it to have the same single driver registering three
different clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
This patch unifies the sun6i AHB1 clock, originally supported
with separate mux and divider clks. It also adds support for
the pre-divider on the PLL6 input, thus allowing the clock to
be muxed to PLL6 with proper clock rate calculation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock modules on the A31 use PLL6x2 as one of their inputs.
This patch changes the PLL6 implementation for A31 to a divs clock,
i.e. clock with multiple outputs that have different dividers.
The first output will be the normal PLL6 output, and the second
will be PLL6x2.
This patch fixes the PLL6 N factor in the clock driver, and removes
any /2 dividers in the PLL6 factors clock part. The N factor counts
from 1 to 32, mapping to values 0 to 31, as shown in the A31 manual.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This driver does not match the hardware, which is actually compatible
to sun4i-a10-apb1-clk. Since we've switch to the correct one, drop
this driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit unifies the APB1 mux with the APB1 clock, using the new
factors infrastructure.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Add mux mask bits]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the gate clocks for AHB/APB busses on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has 12 PLL clocks, 3 AHB clocks, 2 APB clocks, and a
new "GT" bus, which I assume is some kind of data bus connecting
the processor cores, memory and various busses. Also there is a
bus clock for a ARM CCI400 module.
As far as I can tell, the GT bus and CCI400 bus clock must be
protected.
This patch adds driver support for peripheral related PLLs and
bus clocks on the A80. The GT and CCI400 clocks are added as well
as these 2 along with the PLLs they are clocked from must not be
disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MBUS clock on sun8i is slightly different from the old mod0 clocks.
The divider is 3 bits wider, while also needing a divider table for the
higher 4 values, which all set the same divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MMC clock we thought we had until now are actually not one but three
different clocks.
The main one is unchanged, and will have three outputs:
- The clock fed into the MMC
- a sample and output clocks, to deal with when should we output/sample data
to/from the MMC bus
The phase control we had are actually controlling the two latter clocks, but
the main MMC one is unchanged.
We can adjust the phase with a 3 bits value, from 0 to 7, 0 meaning a 180 phase
shift, and the other values being the number of periods from the MMC parent
clock to outphase the clock of.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Even though the mbus clock is a regular module clock, given its nature, it
needs to be enabled all the time.
Introduce a new compatible, to differentiate it from the other module clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 has an almost identical PRCM clock tree. The difference in
the APB0 clock is the smallest divisor is 1, instead of 2.
This patch adds a separate sun8i-a23-apb0-clk driver to support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock control unit on the A23 is similar to the one found on the A31.
The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.
The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.
This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Document new compatible strings for clock provided by the PRCM
(Power/Reset/Clock Management) unit.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Support for the USB gates and resets on A31 has been recently added
using a new compatible, so let's document it here.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the clock driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A20/A31 clock module controls the transmit clock source
and interface type of the GMAC ethernet controller. Model this as
a single clock for GMAC drivers to use.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The A31 has a slightly different PLL6 clock. Add support for this new clock in
our driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Add register definitions for the usb-clk register found on sun4i, sun5i and
sun7i SoCs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
clock-output-names is now required for most of sunxi clock nodes, to
provide the name of the corresponding clock. Add the new requirements,
exceptions, as well as examples.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
That documentation was mostly useful when we didn't have any
documentation for those SoCs, which is not the case anymore. Remove
this, since it should live in the DT anyway.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mark Rutland <mark.rutland@arm.com>
The Allwinner A20 is almost identical to the earlier A10 SoC from
Allwinner on many aspects, including the clocks tree. However, since the
A20 has some additionnal IPs compared to the A10, the clock tree isn't
exactly the same, especially when it comes to the gated clocks
available. We thus need to register different clock gates for the A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The A31 has a mostly different clock set compared to the other older
SoCs currently supported in the Allwinner clock driver.
Add support for the basic useful clocks. The other ones will come in
eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A10s has a slightly different gates set than the A10 and
A13, so add these gates to the clk driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
The A13 has a lot less clocks than the one found in the Allwinner A10.
Add these stripped down clocks to the clock driver and in the
documentation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patchset adds DT support for all the AXI, AHB, APB0 and APB1
gates present on sunxi SoCs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
look pretty much the same; but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
