Some semicolons were left out in the examples.
The #dma-channels and #dma-requests properties have a prefix
that is, by convention, reserved for cell size properties.
Rename those properties to dma-channels and dma-requests.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is based upon the work by Benoit Cousson [1] and Nicolas Ferre [2]
to add some basic helpers to retrieve a DMA controller device_node and the
DMA request/channel information.
Aim of DMA helpers
- The purpose of device-tree is to describe the capabilites of the hardware.
Thinking about DMA controllers purely from the context of the hardware to
begin with, we can describe a device in terms of a DMA controller as
follows ...
1. Number of DMA controllers
2. Number of channels (maybe physical or logical)
3. Mapping of DMA requests signals to DMA controller
4. Number of DMA interrupts
5. Mapping of DMA interrupts to channels
- With the above in mind the aim of the DT DMA helper functions is to extract
the above information from the DT and provide to the appropriate driver.
However, due to the vast number of DMA controllers and not all are using a
common driver (such as DMA Engine) it has been seen that this is not a
trivial task. In previous discussions on this topic the following concerns
have been raised ...
1. How does the binding support devices with multiple DMA controllers?
2. How to support both legacy DMA controllers not using DMA Engine as
well as those that support DMA Engine.
3. When using with DMA Engine how do we support the various
implementations where the opaque filter function parameter differs
between implementations?
4. How do we handle DMA channels that are identified with a string
versus a integer?
- Hence the design of the DMA helpers has to accomodate the above or align on
an agreement what can be or should be supported.
Design of DMA helpers
1. Registering DMA controllers
In the case of DMA controllers that are using DMA Engine, requesting a
channel is performed by calling the following function.
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
The mask variable is used to match a type of the device controller in a list
of controllers. The filter_fn and filter_param are used to identify the
required dma channel and return a handle to the dma channel of type dma_chan.
From the examples I have seen, the mask and filter_fn are constant
for a given DMA controller and therefore, we can specify these as controller
specific data when registering the DMA controller with the device-tree DMA
helpers.
The filter_param variable is of an unknown type and is typically specific
to the DMA engine implementation for a given DMA controller. To allow some
flexibility in the type and formating of this filter_param we employ an
xlate to translate the device-tree binding information into the appropriate
format. The xlate function used for a DMA controller can also be specified
when registering the DMA controller with the device-tree DMA helpers.
Based upon the above, a function for registering the DMA controller with the
DMA helpers now looks like the below. The data variable is used to pass a
pointer to DMA controller specific data used by the xlate function.
int of_dma_controller_register(struct device_node *np,
struct dma_chan *(*of_dma_xlate)
(struct of_phandle_args *, struct of_dma *),
void *data)
For example, in the case where DMA engine is used, we define the following
structure (that stores the DMA engine capability mask and filter function)
and pass this to the data variable in the above function.
struct of_dma_filter_info {
dma_cap_mask_t dma_cap;
dma_filter_fn filter_fn;
};
2. Representing and requesting channel information
Please see the dma binding documentation included in this patch for a
description of how DMA controllers and client information should be
represented with device-tree. For more information on how this binding
came about please see [3]. In addition to this, feedback received from
the Linux kernel summit showed a consensus (among those who attended) to
use a name to identify DMA client information [4].
A DMA channel can be requested by calling the following function, where name
is a required parameter used for identifying a DMA channel. This function
has been designed to return a structure of type dma_chan to work with the
DMA engine driver. Note that if DMA engine is used then drivers should be
using the DMA engine API dma_request_slave_channel() (implemented in part 2
of this series, "dmaengine: add helper function to request a slave DMA
channel") which will in turn call the below function if device-tree is
present. The aim being to have a common DMA engine interface regardless of
whether device tree is being used.
struct dma_chan *of_dma_request_slave_channel(struct device_node *np,
char *name)
3. Supporting legacy devices not using DMA Engine
These devices present a problem, as there may not be a uniform way to easily
support them with regard to device tree. Ideally, these should be migrated
to DMA engine. However, if this is not possible, then they should still be
able to use this binding, the only constaint imposed by this implementation
is that when requesting a DMA channel via of_dma_request_slave_channel(), it
will return a type of dma_chan.
This implementation has been tested on OMAP4430 using the kernel v3.6-rc5. I
have validated that MMC is working on the PANDA board with this implementation.
My development branch for testing on OMAP can be found here [5].
v6: - minor corrections in DMA binding documentation
v5: - minor update to binding documentation
- added loop to exhaustively search for a slave channel in the case where
there could be alternative channels available
v4: - revert the removal of xlate function from v3
- update the proposed binding format and APIs based upon discussions [3]
v3: - avoid passing an xlate function and instead pass DMA engine parameters
- define number of dma channels and requests in dma-controller node
v2: - remove of_dma_to_resource API
- make property #dma-cells required (no fallback anymore)
- another check in of_dma_xlate_onenumbercell() function
[1] http://article.gmane.org/gmane.linux.drivers.devicetree/12022
[2] http://article.gmane.org/gmane.linux.ports.arm.omap/73622
[3] http://marc.info/?l=linux-omap&m=133582085008539&w=2
[4] http://pad.linaro.org/arm-mini-summit-2012
[5] https://github.com/jonhunter/linux/tree/dev-dt-dma
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example,
power-off by restarting to letting u-boot hold the SoC until the user
presses a key. Add a generic driver to implement this. It binds a function
to pm_power_off, which calls arm_pm_restart.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The QNAP NAS boxes have a microcontroller attached to the SoCs second
serial port. By sending it a simple command, it will turn the power for
the board off. This driver registers a function for pm_power_off to send
such a command.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
'clock-output-names' is not used in any of the dts/dtsi files for i.mx.
Remove it from the examples, so that the example and the real usage in the
dtsi files can match.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory
corruption in the at91 driver
- Add the missing device tree binding doc for the
SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration
from the device tree, it was previously retired
from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin
controller.
- Provide the prcm_base from the device tree in the
DT boot path for the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ca6M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A first round of pinctrl fixes for v3.8:
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory corruption in the at91
driver
- Add the missing device tree binding doc for the SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration from the device
tree, it was previously retired from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin controller.
- Provide the prcm_base from the device tree in the DT boot path for
the Nomadik pin controller."
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: ux500: add pinctrl address resources
pinctrl: nomadik: return if prcm_base is NULL
pinctrl: sirf: enable GPIO pullup/down configuration from dts
pinctrl: sirf: add missing DT-binding document
pinctrl: fix comment mistake
drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration
This patch adds device tree support for imx keypad driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the common machine driver to support more boards including Zoom2 and
SDP3430.
- Support for voice port of twl4030
- HS jack plug detection support
- The audio routing can be fine tuned via pdata or via provided routing
table from DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support for the TI TPS51632. Add device binding document also.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 7bec207427 remove sirfsoc_gpio_set_pull function,
this patches takes the feature back by adding sirf,pullups and
sirf,pulldowns prop in dts, and the driver will set the GPIO
pull according to the dts.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While sending email to Linus for reviewing:
"pinctrl: sirf: add DT-binding pinmux mapping support"
https://patchwork.kernel.org/patch/1364361/
i have included the devicetree/bindings/pinctrl/pinctrl-sirf.txt
But while sending pull request with commit 056876f6c7,
i missed the document.
this patch takes the document back.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CS4271 requires its LRCLK and MCLK to be stable before its RESET
line is de-asserted. That also means that clocks cannot be changed
without putting the chip back into hardware reset, which also requires
a complete re-initialization of all registers.
One (undocumented) workaround is to assert and de-assert the PDN bit
in the MODE2 register.
This patch adds a new flag to both the DT bindings as well as to the
platform data to enable that workaround.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull watchdog updates from Wim Van Sebroeck:
"This includes some fixes and code improvements (like
clk_prepare_enable and clk_disable_unprepare), conversion from the
omap_wdt and twl4030_wdt drivers to the watchdog framework, addition
of the SB8x0 chipset support and the DA9055 Watchdog driver and some
OF support for the davinci_wdt driver."
* git://www.linux-watchdog.org/linux-watchdog: (22 commits)
watchdog: mei: avoid oops in watchdog unregister code path
watchdog: Orion: Fix possible null-deference in orion_wdt_probe
watchdog: sp5100_tco: Add SB8x0 chipset support
watchdog: davinci_wdt: add OF support
watchdog: da9052: Fix invalid free of devm_ allocated data
watchdog: twl4030_wdt: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
watchdog: remove depends on CONFIG_EXPERIMENTAL
watchdog: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
watchdog: DA9055 Watchdog driver
watchdog: omap_wdt: eliminate goto
watchdog: omap_wdt: delete redundant platform_set_drvdata() calls
watchdog: omap_wdt: convert to devm_ functions
watchdog: omap_wdt: convert to new watchdog core
watchdog: WatchDog Timer Driver Core: fix comment
watchdog: s3c2410_wdt: use clk_prepare_enable and clk_disable_unprepare
watchdog: imx2_wdt: Select the driver via ARCH_MXC
watchdog: cpu5wdt.c: add missing del_timer call
watchdog: hpwdt.c: Increase version string
watchdog: Convert twl4030_wdt to watchdog core
davinci_wdt: preparation for switch to common clock framework
...
error and a missing symbol export.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=srgY
-----END PGP SIGNATURE-----
mergetag object bc1008cf7d
type commit
tag gpio-for-linus
tagger Grant Likely <grant.likely@secretlab.ca> 1355962627 +0000
GPIO device driver bug fixes:
- gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
- gpio/ich: Add missing spinlock init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JGvn
-----END PGP SIGNATURE-----
mergetag object d3601e56cf
type commit
tag spi-for-linus
tagger Grant Likely <grant.likely@secretlab.ca> 1355962904 +0000
SPI device driver bug fixes branch for the v3.8 merge window. Most of
this is bug fixes to the core code and the sh-hspi and s3c64xx device
drivers.
There is also a patch here to add DT support to the Atmel driver. This
one should have been in the first round, but I missed it. It's a low
risk change contained within a single driver and the Atmel maintainer
has requested it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=trRO
-----END PGP SIGNATURE-----
Merge tags 'dt-for-linus', 'gpio-for-linus' and 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull devicetree, gpio and spi bugfixes from Grant Likely:
"Device tree v3.8 bug fix:
- Fixes an undefined struct device build error and a missing symbol
export.
GPIO device driver bug fixes:
- gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
- gpio/ich: Add missing spinlock init
SPI device driver bug fixes:
- Most of this is bug fixes to the core code and the sh-hspi and
s3c64xx device drivers.
- There is also a patch here to add DT support to the Atmel driver.
This one should have been in the first round, but I missed it.
It's a low risk change contained within a single driver and the
Atmel maintainer has requested it."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: define struct device in of_platform.h if !OF_DEVICE and !OF_ADDRESS
of: Fix export of of_find_matching_node_and_match()
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/mvebu-gpio: Make mvebu-gpio depend on OF_CONFIG
gpio/ich: Add missing spinlock init
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/sh-hspi: fix return value check in hspi_probe().
spi: fix tegra SPI binding examples
spi/atmel: add DT support
of/spi: Fix SPI module loading by using proper "spi:" modalias prefixes.
spi: Change FIFO flush operation and spi channel off
spi: Keep chipselect assertion during one message
This adds OF support for davinci_wdt driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
A new driver has been added for the SPEAr platform and the TWL4030/6030
driver has been replaced by two drivers that control the regular PWMs
and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have all
been improved and the device tree bindings now support the PWM signal
polarity.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=m+7I
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"A new driver has been added for the SPEAr platform and the
TWL4030/6030 driver has been replaced by two drivers that control the
regular PWMs and the PWM driven LEDs provided by the chips.
The vt8500, tiecap, tiehrpwm, i.MX, LPC32xx and Samsung drivers have
all been improved and the device tree bindings now support the PWM
signal polarity."
Fix up trivial conflicts due to __devinit/exit removal.
* tag 'for-3.8-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (21 commits)
pwm: samsung: add missing s3c->pwm_id assignment
pwm: lpc32xx: Set the chip base for dynamic allocation
pwm: lpc32xx: Properly disable the clock on device removal
pwm: lpc32xx: Fix the PWM polarity
pwm: i.MX: eliminate build warning
pwm: Export of_pwm_xlate_with_flags()
pwm: Remove pwm-twl6030 driver
pwm: New driver to support PWM driven LEDs on TWL4030/6030 series of PMICs
pwm: New driver to support PWMs on TWL4030/6030 series of PMICs
pwm: pwm-tiehrpwm: pinctrl support
pwm: tiehrpwm: Add device-tree binding
pwm: pwm-tiehrpwm: Adding TBCLK gating support.
pwm: pwm-tiecap: pinctrl support
pwm: tiecap: Add device-tree binding
pwm: Add TI PWM subsystem driver
pwm: Device tree support for PWM polarity
pwm: vt8500: Ensure PWM clock is enabled during pwm_config
pwm: vt8500: Fix build error
pwm: spear: Staticize spear_pwm_config()
pwm: Add SPEAr PWM chip driver support
...
Fix name of slink binding and address of sflash example to make it
self consistent.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
Add device tree support to the rtc-imxdi driver.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhance rtc-omap driver with DT capability
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull DRM updates from Dave Airlie:
"This is the one and only next pull for 3.8, we had a regression we
found last week, so I was waiting for that to resolve itself, and I
ended up with some Intel fixes on top as well.
Highlights:
- new driver: nvidia tegra 20/30/hdmi support
- radeon: add support for previously unused DMA engines, more HDMI
regs, eviction speeds ups and fixes
- i915: HSW support enable, agp removal on GEN6, seqno wrapping
- exynos: IPP subsystem support (image post proc), HDMI
- nouveau: display class reworking, nv20->40 z compression
- ttm: start of locking fixes, rcu usage for lookups,
- core: documentation updates, docbook integration, monotonic clock
usage, move from connector to object properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (590 commits)
drm/exynos: add gsc ipp driver
drm/exynos: add rotator ipp driver
drm/exynos: add fimc ipp driver
drm/exynos: add iommu support for ipp
drm/exynos: add ipp subsystem
drm/exynos: support device tree for fimd
radeon: fix regression with eviction since evict caching changes
drm/radeon: add more pedantic checks in the CP DMA checker
drm/radeon: bump version for CS ioctl support for async DMA
drm/radeon: enable the async DMA rings in the CS ioctl
drm/radeon: add VM CS parser support for async DMA on cayman/TN/SI
drm/radeon/kms: add evergreen/cayman CS parser for async DMA (v2)
drm/radeon/kms: add 6xx/7xx CS parser for async DMA (v2)
drm/radeon: fix htile buffer size computation for command stream checker
drm/radeon: fix fence locking in the pageflip callback
drm/radeon: make indirect register access concurrency-safe
drm/radeon: add W|RREG32_IDX for MM_INDEX|DATA based mmio accesss
drm/exynos: support extended screen coordinate of fimd
drm/exynos: fix x, y coordinates for right bottom pixel
drm/exynos: fix fb offset calculation for plane
...
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KVPX
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
This is a branch with updates for Marvell's mvebu/kirkwood platforms. They
came in late-ish, and were heavily interdependent such that it didn't
make sense to split them up across the cross-platform topic branches. So
here they are (for the second release in a row) in a branch on their own.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQy5i9AAoJEIwa5zzehBx3ZskP/2wxjbwEaNdnR+7j8595bTaa
GYq8qJ4lUCOKmSqp3bQkg/Plm2D88p78BO5qTm2io527gl10HemzCiGaejclujIw
sDFZPAE8K0Z8p0gQcBNlRZNuI3J1N6IKRqYH5SIJ2vWmBMfO7nKRR9nmTiDpm5bx
IcuKX2u/mhyXWN+F0EcHqcupH1K+mdzyGdIQk80Tyqni+UTN+pd0efLM6WL4SFJM
5fj64dDFpVDA8t+O2Avz8p+lx07vkSy2wIXWt7Ik9BVtsyZQecn+9lpl8FvcrSK/
MgL3QO4kqDpJDs88M7DJURU1/EdsWZc32M63avctaWnGWItQAbOJYBDmZTlng08x
ZGrKOgf/I6le7wEpnzdag9ymI/rAL8I0755FkfXxf1R7/X40b+t8/61J/ddOKTDs
1sTVt+eKyyIMWle4V4zENa03goVBApCIEXcmnuFisFNbBY6azV31inJEp/3PvpgE
GeMBfxBDkvn+03LkRFcZlhTeDsNTdctD+sfgrNPaQf5bZGIvEz87vgfNTIiaU3GA
Vd5aiainVDQgmpoFfRG6391gdFlF2l9d67LoG4ClCjn4WL+UxcTRuzBW/liORpUO
E7CwMHtPq6eoGKywiKMFRzY2QRIKZRkxrC2PCJ/1V9mbIGwgaD/3BQ2/czwrnc8q
1gnxWx8E5SKEGcDJXD+6
=7luC
-----END PGP SIGNATURE-----
Merge tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
This branch contains device-tree updates for the SPEAr platform.
They had dependencies on earlier branches from this merge window,
which is why they were broken out in a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=iK4W
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
"This branch contains device-tree updates for the SPEAr platform. They
had dependencies on earlier branches from this merge window, which is
why they were broken out in a separate branch."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
ARM: SPEAr1310: Fix AUXDATA for compact flash controller
ARM: SPEAr13xx: Remove fields not required for ssp controller
ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
ARM: SPEAr: DT: Update device nodes
ARM: SPEAr: DT: add uart state to fix warning
ARM: SPEAr: DT: Modify DT bindings for STMMAC
ARM: SPEAr: DT: Fix existing DT support
ARM: SPEAr: DT: Update partition info for MTD devices
ARM: SPEAr: DT: Update pinctrl list
ARM: SPEAr13xx: DT: Add spics gpio controller nodes
This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that we
couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=77Ct
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Soc updates, take 2, from Olof Johansson:
"This is the second batch of SoC updates for the 3.8 merge window,
containing parts that had dependencies on earlier branches such that
we couldn't include them with the first branch.
These are general updates for Samsung Exynos, Renesas/shmobile and a
topic branch that adds SMP support to Altera's socfpga platform."
Fix up conflicts mostly as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
sh: clkfwk: fixup unsed variable warning
Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
ARM: highbank: use common debug_ll_io_init
ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
ARM: shmobile: sh7372: remove fsidivx clock
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.
* next/smp:
ARM: socfpga: mark secondary_trampoline as cpuinit
socfpga: map uart into virtual address space so that early_printk() works
ARM: socfpga: fix build break for allyesconfig
ARM: socfpga: Enable SMP for socfpga
Signed-off-by: Olof Johansson <olof@lixom.net>
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace the
proprietary Nokia BME stack;
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks to
Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers;
- Random fixups and enhancements for a bunch of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQyFGdAAoJEGgI9fZJve1bYy8P/iu4XRL2kNwmPD7fMO+bZSao
xCSi8zRCnOtDutB48MQXIDTi1+I64+Qqq5xTuHW5n/T0zJ88biGBZfmJLjM88oQ4
ZqfO/axT6/MNFXTQtxEvXtn/AoM6lp9ZLmIbs7mkSpcnuG8iY5eovKfeyyNiAoGh
W6ISc9d1zZl8JYZXkkX4y5uxsH/t34rPjWJqygMulJrVdePpC9fNWwDYnul6T7iF
/bbqIH/j88HSYNDN518dv/ot+OfPn0vuxD4WzGAqC7ddHICtuaw8TBfXHmr6j4Mf
o9ytC/dH+AQ6Tcs+h7mbz/dfL4Gs9JK2LgRX2z1DtFa6uTw5jwEtZSuDF4DKovEg
71T67dsHDKJkQgGMDfDw1BrlLjQr8hkaWroF8CdmbRO0rRsfKamLQANG7mGkSu8B
l1W0ZzWEbHDteNB/wCkjoncXlcqoA8YiplyVSqf38aP8YuaeHMR3LRGLFwgXK3pB
lELh3cYSYLVpcqUgkRWcPrCUnLA2CkQy2B4INj5jFZilux7DzyIHMhWI2OuUs2rH
1rwTYO91gTVONuagZn8+lmsjs+Yq1n2BcyrGMG2+ZYzruFaQ+brQsCbQR0hdRuaU
zWLENqwGJ/++XrFgw3/5orMZIZQzL/yq+MbIXtrgKcFRWwoxyzJuH63RMQf3S6yy
hxi7pYQmb9if+HPJZVVg
=Bb5O
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
Primarily SPI device driver bug fixes, one removal of an old driver, and
some new tegra support. There is some core code change too, but all in
all pretty small stuff. The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bvpH
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI updates from Grant Likely:
"Primarily SPI device driver bug fixes, one removal of an old driver,
and some new tegra support. There is some core code change too, but
all in all pretty small stuff.
The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
spi/sparc: Allow of_register_spi_devices for sparc
spi: Remove HOTPLUG section attributes
spi: Add support for specifying 3-wire mode via device tree
spi: Fix comparison of different integer types
spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
spi/sh: Add SH Mobile series as dependency to MSIOF controller
spi/sh-msiof: Remove unneeded clock name
spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
spi/stmp: remove obsolete driver
spi/clps711x: New SPI master driver
spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
spi: omap2-mcspi: Fix the redifine warning
spi/sh-hspi: add CS manual control support
of_spi: add generic binding support to specify cs gpio
spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
spi/bitbang: (cosmetic) simplify list manipulation
spi/bitbang: avoid needless loop flow manipulations
spi/omap: fix D0/D1 direction confusion
spi: tegra: add spi driver for sflash controller
spi: Dont call master->setup if not populated
...
A fairly quiet release again, a couple of relatively small new features
and a bunch of driver specific work including yet more code elimination
and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM vexpress.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2d65
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release again, a couple of relatively small new
features and a bunch of driver specific work including yet more code
elimination and fixes from Axel Lin.
- Addidion of linear_min_sel for offsetting linear selectors in the
helpers.
- Support for continuous voltage ranges for regulators with extremely
high resolution.
- Drivers for AS3711, DA9055, MAX9873, TPS51632, TPS80031 and ARM
vexpress."
Fix up trivial conflict (due to typo fix) in palmas-regulator.c
* tag 'regulator-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (80 commits)
regulator: core: Fix logic to determinate if regulator can change voltage
regulator: s5m8767: Fix to work even if no DVS gpio present
regulator: s5m8767: Fix to read the first DVS register.
regulator: s5m8767: Fix to work when platform registers less regulators
regulator: gpio-regulator: gpio_set_value should use cansleep
regulator: gpio-regulator: Fix logical error in for() loop
regulator: anatop: Use regulator_[get|set]_voltage_sel_regmap
regulator: anatop: Use linear_min_sel with linear mapping
regulator: max1586: Implement get_voltage_sel callback
regulator: lp8788-buck: Kill _gpio_request function
regulator: tps80031: Convert tps80031_ldo_ops to linear_min_sel and list_voltage_linear
regulator: lp8788-ldo: Remove val array in lp8788_config_ldo_enable_mode
regulator: gpio-regulator: Add ifdef CONFIG_OF guard for regulator_gpio_of_match
regulator: palmas: Convert palmas_ops_smps to regulator_[get|set]_voltage_sel_regmap
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
regulators: add regulator_can_change_voltage() function
regulator: tps51632: Ensure [base|max]_voltage_uV pdata settings are valid
regulator: wm831x-dcdc: Add MODULE_ALIAS for wm831x-boostp
regulator: wm831x-dcdc: Ensure selected voltage falls within requested range
regulator: tps51632: Use linear_min_sel and regulator_[map|list]_voltage_linear
...
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is
not quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq. note
that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UJlh
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms have
seen pinctrl-via-devicetree conversions for simpler multiplatform. Tegra
is adding data for new devices/drivers, and Exynos has a bunch of new
bindings and devices added as well.
So, pretty much the same progression in the right direction as the last
few releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rk9v
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's also
taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMKB
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
Pull ARM updates from Russell King:
"Here's the updates for ARM for this merge window, which cover quite a
variety of areas.
There's a bunch of patch series from Will tackling various bugs like
the PROT_NONE handling, ASID allocation, cluster boot protocol and
ASID TLB tagging updates.
We move to a build-time sorted exception table rather than doing the
sorting at run-time, add support for the secure computing filter, and
some updates to the perf code. We also have sorted out the placement
of some headers, fixed some build warnings, fixed some hotplug
problems with the per-cpu TWD code."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (73 commits)
ARM: 7594/1: Add .smp entry for REALVIEW_EB
ARM: 7599/1: head: Remove boot-time HYP mode check for v5 and below
ARM: 7598/1: net: bpf_jit_32: fix sp-relative load/stores offsets.
ARM: 7595/1: syscall: rework ordering in syscall_trace_exit
ARM: 7596/1: mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep
ARM: 7597/1: net: bpf_jit_32: fix kzalloc gfp/size mismatch.
ARM: 7593/1: nommu: do not enable DCACHE_WORD_ACCESS when !CONFIG_MMU
ARM: 7592/1: nommu: prevent generation of kernel unaligned memory accesses
ARM: 7591/1: nommu: Enable the strict alignment (CR_A) bit only if ARCH < v6
ARM: 7590/1: /proc/interrupts: limit the display of IPIs to online CPUs only
ARM: 7587/1: implement optimized percpu variable access
ARM: 7589/1: integrator: pass the lm resource to amba
ARM: 7588/1: amba: create a resource parent registrator
ARM: 7582/2: rename kvm_seq to vmalloc_seq so to avoid confusion with KVM
ARM: 7585/1: kernel: fix nr_cpu_ids check in DT logical map init
ARM: 7584/1: perf: fix link error when CONFIG_HW_PERF_EVENTS is not selected
ARM: gic: use a private mapping for CPU target interfaces
ARM: kernel: add logical mappings look-up
ARM: kernel: add cpu logical map DT init in setup_arch
ARM: kernel: add device tree init map function
...
Pull thermal management update from Zhang Rui:
"Highlights:
- Introduction of thermal policy support, together with three new
thermal governors, including step_wise, user_space, fire_share.
- Introduction of ST-Ericsson db8500_thermal driver and ST-Ericsson
db8500_cpufreq_cooling driver.
- Thermal Kconfig file and Makefile refactor.
- Fixes for generic thermal layer, generic cpucooling, rcar thermal
driver and Exynos thermal driver."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
Thermal: Fix DEFAULT_THERMAL_GOVERNOR
Thermal: fix a NULL pointer dereference when generic thermal layer is built as a module
thermal: rcar: add rcar_zone_to_priv() macro
thermal: rcar: fixup the unit of temperature
thermal: cpu cooling: allow module builds
thermal: cpu cooling: use const parameter while registering
Thermal: Add ST-Ericsson DB8500 thermal properties and platform data.
Thermal: Add ST-Ericsson DB8500 thermal driver.
drivers/thermal/Makefile refactor
Exynos: Add missing dependency
Refactor drivers/thermal/Kconfig
thermal: cpu_cooling: Make 'notify_device' static
Thermal: Remove the cooling_cpufreq_list.
Thermal: fix bug of counting cpu frequencies.
Thermal: add indent for code alignment.
thermal: rcar_thermal: remove explicitly used devm_kfree/iounap()
thermal: user_space: Add missing static storage class specifiers
thermal: fair_share: Add missing static storage class specifiers
thermal: step_wise: Add missing static storage class specifiers
Thermal: Fix oops and unlocking in thermal_sys.c
...
The merge is merely to fix conflicts before sending a pull request.
Conflicts:
drivers/power/ab8500_btemp.c
drivers/power/ab8500_charger.c
drivers/power/ab8500_fg.c
drivers/power/abx500_chargalg.c
drivers/power/max8925_power.c
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2XeO
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO updates from Grant Likely:
"GPIO follow up patch and type change for v3.5 merge window
Primarily device driver additions, features and bug fixes. Not much
touching gpio common subsystem support. Should not be scary."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio: Provide the STMPE GPIO driver with its own IRQ Domain
gpio: add TS-5500 DIO blocks support
gpio: pcf857x: use client->irq for gpio_to_irq()
gpio: stmpe: Add DT support for stmpe gpio
gpio: pl061 depends on ARM
gpio/pl061: remove old comment
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
GPIO: clps711x: use platform_device_unregister in gpio_clps711x_init()
gpio/tc3589x: convert to use the simple irqdomain
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
Bug fixes, little cleanups, and documentation changes. The most invasive
thing here touches a bunch of the arch directories to use a common build
rule for .dtb files. There are no major changes to functionality here
other than a ew new helper functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LB3n
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree changes from Grant Likely:
"Here are the DT changes I've got queued up for v3.8. As described
below, there are a lot of bug fixes here and documentation updates but
nothing major:
Bug fixes, little cleanups, and documentation changes. The most
invasive thing here touches a bunch of the arch directories to use a
common build rule for .dtb files. There are no major changes to
functionality here other than a few new helper functions."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
arm64: Fix the dtbs target building
mtd: nand: davinci: fix the binding documentation
rtc: rtc-mv: Add the device tree binding documentation
devicetree/bindings: Move gpio-leds binding into leds directory
of/vendor-prefixes: add Imagination Technologies
microblaze: use new common dtc rule
c6x: use new common dtc rule
openrisc: use new common dtc rule
arm64: Add dtbs target for building all the enabled dtb files
arm64: use new common dtc rule
ARM: dt: change .dtb build rules to build in dts directory
kbuild: centralize .dts->.dtb rule
Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
of/spi: Honour "status=disabled" property of device
of_mdio: Honour "status=disabled" property of device
of_i2c: Honour "status=disabled" property of device
powerpc: Fix fallout from device_node->name constification
of: add 'const' for of_parse_phandle parameter *np
Documentation: correct of_platform_populate() argument list
script: dtc: clean generated files
...
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices and
MFDs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GoXf
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Mike Turquette:
"The common clock framework changes for 3.8 are comprised of lots of
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices
and MFDs."
Fix up trivial conflict in <linux/clk-provider.h> (removal of 'inline'
clashing with return type fixes)
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (51 commits)
MAINTAINERS: bad email address for Mike Turquette
clk: introduce optional disable_unused callback
clk: ux500: fix bit error
clk: clock multiplexers may register out of order
clk: ux500: Initial support for abx500 clock driver
CLK: SPEAr: Remove unused dummy apb_pclk
CLK: SPEAr: Correct index scanning done for clock synths
CLK: SPEAr: Update clock rate table
CLK: SPEAr: Add missing clocks
CLK: SPEAr: Set CLK_SET_RATE_PARENT for few clocks
CLK: SPEAr13xx: fix parent names of multiple clocks
CLK: SPEAr13xx: Fix mux clock names
CLK: SPEAr: Fix dev_id & con_id for multiple clocks
clk: move IM-PD1 clocks to drivers/clk
clk: make ICST driver handle the VCO registers
clk: add GPLv2 headers to the Versatile clock files
clk: mxs: Use a better name for the USB PHY clock
clk: spear: Add stub functions for spear3[0|1|2]0_clk_init()
CLK: clk-twl6040: fix return value check in twl6040_clk_probe()
clk: ux500: Register nomadik keypad clock lookups for u8500
...
As can be seen from the diffstat the major changes
are:
- A big conversion of the AT91 pinctrl driver and
the associated ACKed platform changes under
arch/arm/max-at91 and its device trees. This
has been coordinated with the AT91 maintainers
to go in through the pinctrl tree.
- A larger chunk of changes to the SPEAr drivers
and the addition of the "plgpio" driver for the
SPEAr as well.
- The removal of the remnants of the Nomadik driver
from the arch/arm tree and fusion of that into
the Nomadik driver and platform data header files.
- Some local movement in the Marvell MVEBU drivers,
these now have their own subdirectory.
- The addition of a chunk of code to gpiolib under
drivers/gpio to register gpio-to-pin range mappings
from the GPIO side of things. This has been
requested by Grant Likely and is now implemented,
it is particularly useful for device tree work.
Then we have incremental updates all over the place,
many of these are cleanups and fixes from Axel Lin
who has done a great job of removing minor mistakes
and compilation annoyances.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=rUOP
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the first and major pinctrl changes for the v3.8 merge
cycle. Some of this is used as merge base for other trees so I better
be early on the trigger.
As can be seen from the diffstat the major changes are:
- A big conversion of the AT91 pinctrl driver and the associated ACKed
platform changes under arch/arm/max-at91 and its device trees. This
has been coordinated with the AT91 maintainers to go in through the
pinctrl tree.
- A larger chunk of changes to the SPEAr drivers and the addition of
the "plgpio" driver for the SPEAr as well.
- The removal of the remnants of the Nomadik driver from the arch/arm
tree and fusion of that into the Nomadik driver and platform data
header files.
- Some local movement in the Marvell MVEBU drivers, these now have
their own subdirectory.
- The addition of a chunk of code to gpiolib under drivers/gpio to
register gpio-to-pin range mappings from the GPIO side of things.
This has been requested by Grant Likely and is now implemented, it
is particularly useful for device tree work.
Then we have incremental updates all over the place, many of these are
cleanups and fixes from Axel Lin who has done a great job of removing
minor mistakes and compilation annoyances."
* tag 'pinctrl-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (114 commits)
ARM: mmp: select PINCTRL for ARCH_MMP
pinctrl: Drop selecting PINCONF for MMP2, PXA168 and PXA910
pinctrl: pinctrl-single: Fix error check condition
pinctrl: SPEAr: Update error check for unsigned variables
gpiolib: Fix use after free in gpiochip_add_pin_range
gpiolib: rename pin range arguments
pinctrl: single: support gpio request and free
pinctrl: generic: add input schmitt disable parameter
pinctrl/u300/coh901: stop spawning pinctrl from GPIO
pinctrl/u300/coh901: let the gpio_chip register the range
pinctrl: add function to retrieve range from pin
gpiolib: return any error code from range creation
pinctrl: make range registration defer properly
gpiolib: rename find_pinctrl_*
gpiolib: let gpiochip_add_pin_range() specify offset
ARM: at91: pm9g45: add mmc support
ARM: at91: Animeo IP: add mmc support
ARM: at91: dt: add mmc pinctrl for Atmel reference boards
ARM: at91: dt: at91sam9: add mmc pinctrl support
ARM: at91/dts: add nodes for atmel hsmci controllers for atmel boards
...
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block") area
by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports that it
supports 1.8V but the board itself has no way to switch to 1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite loop
while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oSX3
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.8:
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block")
area by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports
that it supports 1.8V but the board itself has no way to switch to
1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite
loop while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices
now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."
* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
mmc: sdhci: implement the .card_event() method
mmc: extend the slot-gpio card-detection to use host's .card_event() method
mmc: add a card-event host operation
mmc: sdhci-s3c: Fix compilation warning
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
mmc: sdhci-dove: use devm_clk_get()
mmc: eSDHC: Recover from ADMA errors
mmc: dw_mmc: remove duplicated buswidth code
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
mmc: Limit MMC speed to 52MHz if not HS200
mmc: dw_mmc: use devres functions in dw_mmc
mmc: sh_mmcif: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: fix clock frequency printing
mmc: Remove redundant null check before kfree in bus.c
mmc: Remove redundant null check before kfree in sdio_bus.c
mmc: sdhci-imx-esdhc: use more devm_* functions
mmc: dt: add no-1-8-v device tree flag
...
Since the aemif driver conversion to DT along with
its movement to drivers/ folder is not yet done,
fix NAND binding documentation to have NAND specific
DT details only.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The support was already written, but the binding documentation was
lacking.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Alex writes:
Pretty minor -next pull request. We some additional new bits waiting
internally for release. Hopefully Monday we can get at least some of
them out. The others will probably take a few more weeks.
Highlights of the current request:
- ELD registers for passing audio information to the sound hardware
- Handle GPUVM page faults more gracefully
- Misc fixes
Merge radeon test
* 'drm-next-3.8' of git://people.freedesktop.org/~agd5f/linux: (483 commits)
drm/radeon: bump driver version for new info ioctl requests
drm/radeon: fix eDP clk and lane setup for scaled modes
drm/radeon: add new INFO ioctl requests
drm/radeon/dce32+: use fractional fb dividers for high clocks
drm/radeon: use cached memory when evicting for vram on non agp
drm/radeon: add a CS flag END_OF_FRAME
drm/radeon: stop page faults from hanging the system (v2)
drm/radeon/dce4/5: add registers for ELD handling
drm/radeon/dce3.2: add registers for ELD handling
radeon: fix pll/ctrc mapping on dce2 and dce3 hardware
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
Revert "drm/i915: enable rc6 on ilk again"
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
...
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_encoder.c
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/core/engine/disp/nv50.c
Add support for the Solomon SSD1307 OLED controller found on the
Crystalfontz CFA10036 board.
This controller can drive a display with a resolution up to 128x39 and can
operate over I2C or SPI.
The current driver has only been tested on the CFA-10036, that is using
this controller over I2C to driver a 96x16 OLED screen.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Thomas Petazzoni <thomas@free-electrons.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch extends existing DT support for stmpe devices. This updates:
- missing header files in stmpe.c
- stmpe_of_probe() with pwm, rotator and new bindings.
- Bindings are updated in binding document.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to specify that a SPI device is connected in 3-wire mode via
device tree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.
Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for pin configuration using pinctrl subsystem
to the sdhci-s3c driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add documentation for pm capabilties such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The compatible property in device tree "crypto" node has been enhanced
to provide SEC ERA information to the applications.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "powervr" prefix which is currently described as "Imagination
Technologies" isn't really appropriate for non-PowerVR hardware, so
deprecate it, changing the description of "powervr" to "PowerVR
(deprecated, use img)", and add a separate "img" prefix for "Imagination
Technologies Ltd.".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows the STMPE GPIO driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQtOFbAAoJEAi3KVZQDZAeRbkH/3IWYaAFXi6wnM4yHdYJbp5A
X1375b4Tkjd2Q05gujtNZLDS1gR4O65gJ9nxoV4OuYtqt1WnFUTDU4WozaYFdj8G
1hojkI6qKUddV+EZdMkx1/0YXORsNbGx8PHFPzsLfMHL/qEWjdMgOf4UW+9AogVt
hOwQwIs7SuhDnu0QR0dUH65iU848n5dYSczr/j71l2fqooJ/+KaU1hKKYf/rFvX2
3f9TaDydeglgAUGs7FUL1EbuLQiygIGy1wDhxyVK+g7inAzdQGzVZ7faK8M3NScM
YixWH+uy35ZAS8LlPCpY7DFts4pMtB/5fFvWiMYaBXv53mClgqSaymQDZLObJi8=
=rcOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper:
mvebu cache-l2x0 for v3.8
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
* tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux:
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
merge conflicts with orion/*
- arch/arm/mach-kirkwood/Kconfig
- select everything
- arch/arm/mach-kirkwood/board-dt.c
- remove AUXDATA
- keep all of_machine_is_compatible()
- use of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsFAhAAoJEAi3KVZQDZAedzgH/3VodO3dDqL4A5HCoUj56HXF
Chkv1cl+1VS3sPnsbbluG0fmDdB619i4Oi2bUWc1YdLpEE0xgyjeAzl5vZDFBjrS
tb8nhWCd2vEcKFSC+HVU2Rhj0NwgUoQifoeD7NSovYZJE6+z+KEY5ny0sE4uaWE1
NL+StBI9dH+SvMi59rnsAxteAnBEAosUoY4KaoHcTHvPsqm9xW5GBh1MkSXQB7fx
kwRrdCaM8U3y3J933/Y4C3maDDQVL7v27YgQp+U5r/eRyN7fVVccxLr6xwl9sck2
fjEpbNRYMImvCOKh8+dhllf/8ZOmjdOore4ORbk4Ulame2KL6pG/2fZ+5N+FrRQ=
=QHBZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper. Unfortunately this is a combined branch with all
mvebu code as one drop, something we normally try to avoid and instead
slice vendor topics across our branches. Hopefully we can avoid doing
this again for 3.9!
mvebu everything for v3.8
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
* tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux: (85 commits)
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
arm: mvebu: Add support for coherency fabric in mach-mvebu
arm: mvebu: update defconfig to include XOR driver
arm: mvebu: update defconfig to include network driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
* pm-cpufreq: (21 commits)
cpufreq: ondemand: update sampling rate only on right CPUs
cpufreq: SPEAr: Add CPUFreq driver
cpufreq: governors: Fix jiffies/cputime mixup (revisited)
cpufreq: ondemand: fix wrong delay sampling rate
cpufreq: exynos: Use static for functions used in only this file
cpufreq: exynos: Broadcast frequency change notifications for all cores
cpufreq: remove use of __devexit
cpufreq: remove use of __devinit
cpufreq: remove use of __devexit_p
cpufreq: Remove unnecessary initialization of a local variable
cpufreq: Make sure target freq is within limits
cpufreq: Avoid calling cpufreq driver's target() routine if target_freq == policy->cur
cpufreq: Fix sparse warning by making local function static
cpufreq: Fix sparse warnings by updating cputime64_t to u64
cpufreq: governors: remove redundant code
cpufreq: return early from __cpufreq_driver_getavg()
cpufreq: fix jiffies/cputime mixup in conservative/ondemand governors
cpufreq: Improve debug prints
cpufreq: Move common part from governors to separate file, v2
cpufreq / core: Fix printing of governor and driver name
...
Exynos DP changes for the 3.8 merge window.
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
* 'exynos-dp-next' of git://github.com/jingoo/linux:
video: exynos_dp: remove redundant parameters
video: exynos_dp: Fix incorrect setting for INT_CTL
video: exynos_dp: Reset and initialize DP before requesting irq
video: exynos_dp: Enable hotplug interrupts
video: exynos_dp: Move hotplug into a workqueue
video: exynos_dp: Remove sink control to D0
video: exynos_dp: Fix bug when checking dp->irq
video: exynos_dp: Improve EDID error handling
video: exynos_dp: Get pll lock before pattern set
video: exynos_dp: Clean up SW link training
video: exynos_dp: Check DPCD return codes
video: exynos_dp: device tree documentation
video: exynos_dp: Add device tree support to DP driver
Add documentation for the DT bindings in exynos display port driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Handle the jack detection inforamtion as bool from devicetree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for EHRWPM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch
1. Add support for device-tree binding for ECAP APWM driver.
2. Set size of pwm-cells set to 3 to support PWM channel number, PWM
period & polarity configuration from device tree.
3. Add enable/disable clock gating in PWM subsystem common config space.
4. When here set .owner member in platform_driver structure to
THIS_MODULE.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Aurora is a L2 Cache Controller designed to be compatible with the
L2x0 Cache Controller. L2X0 OF bindings are extended to support some
specificity of Aurora (no cache id part number available through
hardware, always write through mode, choice between outer cache and
system cache).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-and-reviewed-by: Lior Amsalem <alior@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zpgo
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
Present implementation was non-DT and had few complex data structures to
decipher banks, number of irqs supported, mask and registers involved.
This patch simplifies the overall design and convert it in to DT. It
also removes all registration from individual SoC files and bring them
in to common shirq.c.
Also updated the corresponding documentation for DT binding of shirq.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrc/qAAoJEAi3KVZQDZAeGIcIAJ70hcz/cKdEKNpekMRoMWpz
LoDXtPqRuUvCqBdUNFkJyPAhHHkWwnU6KRcBRz1dknTtJ7nyCkDQYRG/JIroIs8I
X9N6JbPH7FMU+Z1ZUAM2ww+pEAIQkwX06erAy9u/a7ivMj/0LeXboNK+ngIx1jgL
xz2SS4wJrujPwvT2rYo4nJ+WwGiiIPbRjiY7r87rD/DQ9nY9DxKgfve7pRhaCCZS
Baw48u8qTe6M9LGcXw+b/MSHGCTB6YabqaRHMAr/1NK0Z3JDGU8tEpOuMCnFX7SA
6CxEymw5/8fzyTgdRz7FRd9Hg28y5Cd+T2l48X4tSL/M16H4EeBOxj6ub4zCi9s=
=nsDw
-----END PGP SIGNATURE-----
Merge tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper:
orion boards for v3.8
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
* tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
From Kukjin Kim:
Here is second Samsung DT stuff for v3.8.
This is including power domain DT support for exynos and Google ARM
Chromebook, Snow board and exynos4210-origen updates.
* 'next/dt-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Use drive strength 3 for SD pins for exynos4
ARM: dts: Set up power domains for exynos4
ARM: EXYNOS: Bind devices to power domains using DT
ARM: EXYNOS: Fix power domain name initialization
ARM: EXYNOS: Detect power domain state on registration from DT
ARM: dts: Add vmmc fixed voltage regulator for exynos4210-origen
ARM: dts: Update sdhci nodes for current bindings for exynos4210-origen
ARM: dts: Update for pinctrl-samsung driver for exynos4210-origen
ARM: dts: Split memory sections for exynos4210-origen
ARM: EXYNOS: add all i2c busses to auxdata for DT
ARM: dts: Add aliases for i2c controller for exynos4
ARM: dts: Add board dts file for Snow board (ARM Chromebook)
ARM: dts: Move the dwmmc aliases from smdk5250 dts to exynos
Add/add conflicts resolved in arch/arm/boot/dts/exynos5250-smdk5250.dts
and arch/arm/mach-exynos/mach-exynos5-dt.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZiZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for v3.8
* tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Given appropriate devicetree bindings, this driver registers a
pm_power_off function to set a GPIO line high/low to power down
your board.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by:Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on previous work by Michael Walle and Jason Cooper.
Made their work actually work, which required added interrupt from DT
and auxdata, along with setting the dma_mask, which DT does not
currently do.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pulling in a newer version of the depend branch from the gpio tree,
since there was some randconfig breakage introduced at the version we
had, and we want to keep those things as bisectable as possible. It's
not bad enough to warrant a rebase though, so there'll be a window of
exposure to this.
* depends/gpio-devel:
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
Signed-off-by: Olof Johansson <olof@lixom.net>
This device doesn't have a pdata definition for legacy boards, and
unless anyone need to control the reset GPIO, it's not worth adding one.
So this feature is only available to DT users for now.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously a generic binding 'i2c-client-wake' was created which
enabled I2C devices to register themselves as wake-up devices.
This binding was later over-thrown by 'wakeup-source'. The STMPE
driver was fixed-up, but the document was neglected. This patch
aims to rectify that.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for encoding PWM properties in bit encoded form with
of_pwm_xlate_with_flags() function support. Platforms require platform
specific PWM properties has to populate in 3rd cell of the pwm-specifier
and PWM driver should also set .of_xlate support with this function.
Currently PWM property polarity encoded in bit position 0 of the third
cell in pwm-specifier.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.
More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.
1. http://www.st.com/internet/mcu/product/251211.jsp
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In recent reference manuals the PLLs were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to use gpio for chip select with no modification in the
driver binding
When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs/LcACgkQCwYYjhRyO9WrOgCfeWpA9XdQnwexySw5tPXS7Qdp
aJEAn2ql07SECpTRWezTJptHL0oI1dFF
=b0T7
-----END PGP SIGNATURE-----
Merge tag 'marvell-hwiocc-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Add hardware I/O coherency support for Armada 370/XP
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
From Michal Simek:
This branch depends on arm-soc devel/debug_ll_init branch because
we needed Rob's "ARM: implement debug_ll_io_init()"
(sha1: afaee03511ba8002b26a9c6b1fe7d6baf33eac86)
patch.
This branch also depends on zynq/dt branch because of previous major
zynq changes.
zynq/cleanup branch is subset of zynq/dt.
* 'zynq/multiplatform' of git://git.monstr.eu/linux-2.6-microblaze:
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Add/add conflict in arch/arm/Kconfig.debug.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: EXYNOS: DT Support for SATA and SATA PHY
ARM: dts: Remove broken-voltage property from sdhci node for exynos4210-trats
ARM: dts: Add node for touchscreen for exynos4210-trats
ARM: dts: Add node for touchscreen voltage regulator for exynos4210-trats
ARM: dts: Add node for i2c3 bus for exynos4210-trats
ARM: dts: Add nodes for GPIO keys available on Trats
ARM: dts: Update for pinctrl-samsung driver for exynos4210-trats
ARM: dts: Add nodes for pin controllers for exynos4x12
pinctrl: samsung: Add support for EXYNOS4X12
gpio: samsung: Skip registration if pinctrl driver is present on EXYNOS4X12
ARM: EXYNOS: Skip wakeup-int setup if pinctrl driver is used on EXYNOS4X12
ARM: dts: add board dts file for EXYNOS4412 based SMDK board
ARM: dts: Add support for EXYNOS4X12 SoCs
ARM: EXYNOS: Add devicetree node for TMU driver for exynos5
ARM: EXYNOS: Add devicetree node for TMU driver for exynos4
ARM: EXYNOS: Add MFC device tree support
ARM: dts: Enable serial controllers on Origen and SMDKV310
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
...
Add/add conflicts in:
arch/arm/boot/dts/exynos5250-smdk5250.dts
arch/arm/boot/dts/exynos5250.dtsi
arch/arm/mach-exynos/mach-exynos5-dt.c
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Here is a pull request to add the support for Allwinner A10 SoCs.
* sunxi/soc2:
ARM: sunxi: Add sunxi restart function via onchip watchdog
ARM: sunxi: Add sun4i and cubieboard support
ARM: sunxi: Add earlyprintk support for UART0 (sun4i)
ARM: sunxi: Restructure sunxi dts/dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This includes supporting legacy i2c controller and ARM down clock
support for exynos5 and small changes.
[olof: It contains a dependency on samsung/hdmi for HDMI DT bindings, for some reason.]
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Clock settings for SATA and SATA PHY
ARM: EXYNOS: Add ARM down clock support
ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
ARM: EXYNOS: Add aliases for i2c controller
ARM: EXYNOS: Setup legacy i2c controller interrupts
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
ARM: EXYNOS: Add dp clock support for EXYNOS5
ARM: SAMSUNG: call clk_get_rate for debugfs rate files
ARM: SAMSUNG: add clock_tree debugfs file in clock
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung DT for v3.8 and this is including DT for EXYNOS4X12
SoC, SMDK4412 board, pinctrl for exynos4x12, TMU, MFC, SATA and SATA
PHY.
As I commented on [4/7], this branch merged pinctrl/samsung to support
pinctrl for exynos4x12 without useless merge conflicts.
* samsung/pinctrl:
pinctrl: samsung: Update error check for unsigned variables
pinctrl: samsung: Add support for EXYNOS4X12
Documentation: Update samsung-pinctrl device tree bindings documentation
pinctrl: samsung: Add GPIO to IRQ translation
pinctrl: exynos: Set pin function to EINT in irq_set_type of wake-up EINT
pinctrl: samsung: Use per-bank IRQ domain for wake-up interrupts
pinctrl: samsung: Use one GPIO chip per pin bank
pinctrl: exynos: Use one IRQ domain per pin bank
pinctrl: samsung: Include bank-specific eint offset in bank struct
pinctrl: samsung: Hold pointer to driver data in bank struct
pinctrl: samsung: Match pin banks with their device nodes
ARM: dts: exynos4210-pinctrl: Add nodes for pin banks
pinctrl: samsung: Distinguish between pin group and bank nodes
pinctrl: samsung: Remove static pin enumerations
pinctrl: samsung: Assing pin numbers dynamically
pinctrl: samsung: Do not pass gpio_chip to pin_to_reg_bank
pinctrl: samsung: Detect and handle unsupported configuration types
From Kukjin Kim:
This is for adding support for DT based exynos5250 hdmi and it adds
device node for hdmi, mixer, hdmiphy and hdmiddc.
* 'next/hdmi-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: removing exynos-drm device registration from non-dt platforms
ARM: EXYNOS: add clocks for exynos5 hdmi
ARM: dts: add device tree support for exynos5 hdmiddc
ARM: dts: add device tree support for exynos5 hdmiphy
ARM: dts: add device tree support for exynos5 mixer
ARM: dts: add device tree support for exynos5 hdmi
Armada 370 and XP come with an unit called coherency fabric. This unit
allows to use the Armada 370/XP as a nearly coherent architecture. The
coherency mechanism uses snoop filters to ensure the coherency between
caches, DRAM and devices. This mechanism needs a synchronization
barrier which guarantees that all the memory writes initiated by the
devices have reached their target and do not reside in intermediate
write buffers. That's why the architecture is not totally coherent and
we need to provide our own functions for some DMA operations.
Beside the use of the coherency fabric, the device units will have to
set the attribute flag of the decoding address window to select the
accurate coherency process for the memory transaction. This is done
each device driver programs the DRAM address windows. The value of the
attribute set by the driver is retrieved through the
orion_addr_map_cfg struct filled during the early initialization of
the platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
There are several drivers that use LEDs and depend on exactly the same
device tree binding. However, the binding documentation has simply been
cut-and-paste into each of the binding documents. Rather than continue
to duplicate it, this patch adds a common led binding document that all
can reference.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enhances the IRQ controller driver to add support for
Inter-Processor-Interrupts that are needed to enable SMP support.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a power management service unit
which is responsible for powering down and waking up CPUs and other
SOC units. This patch adds support for this unit.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and Armada XP SOCs have a coherency fabric unit which
is responsible for ensuring hardware coherency between all CPUs and
between CPUs and I/O masters. This patch provides the basic support
needed for SMP.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch adds a way to specify bindings between devices and power
domains using device tree.
A device can be bound to particular power domain by adding a
power-domain property containing a phandle to the domain. The device
will be bound to the domain before binding a driver to it and unbound
after unbinding a driver from it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Initial state of power domains might vary on different boards and with
different bootloaders.
This patch adds detection of initial state of power domains when being
registered from DT.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set tps65217 PMIC status to OFF if power enable toggle is supported.
By setting this bit to 1 to enter PMIC to OFF state when PWR_EN pin
is pulled low. Also adds a DT flag to specify that device pmic
supports shutdown control or not.
Signed-off-by: Colin Foe-Parker <colin.foeparker@logicpd.com>
[anilkumar@ti.com: move the additions to tps65217 MFD driver]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
From Pawel Moll:
* 'vexpress-clk-soc' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove motherboard dependencies in the DTS files
ARM: vexpress: Start using new Versatile Express infrastructure
ARM: vexpress: Add config bus components and clocks to DTs
mfd: Versatile Express system registers driver
mfd: Versatile Express config infrastructure
From Stephen Warren:
ARM: bcm2835: core SoC enhancements
A machine restart/reboot implementation is added. The GPIO/pinmux
controller is instantiated, and dummy gpio.h added.
* tag 'bcm2835-for-3.8-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: enable GPIO/pinctrl
ARM: bcm2835: implement machine restart hook
Signed-off-by: Olof Johansson <olof@lixom.net>
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQppFoAAoJEMzrak5tbycx1WsQALzqZBCebkEIo0CfuYlVtZrX
co2HBLsTis8KOI1lB5hZZdLvOD2sevwkw+YDtoG1k2ymZvR/Lpl3zdYdPCinA7gb
Qzs+OlwnAla7J5BkgV0v69lZHBYd8jvxsFt9MZo1XkHjw2IRPyrzLhdmBHGLVj3J
Tk7kk4OH64sDhDb+vZJXCtBJV0fvn10WNSskUHoQYZveGOCFGZXogrAht25tcoQO
TM89tasMdRq3IhOxuzHHo/7AegyuTZdDzV4blNr1xOMzyz1b3P3sBh2ZiK+aBztX
CCfpJ2ZUlRqTKSOU4qlM48dWffr/ZyP1u0VVi9Bu4Df/qBpS37NjagiVxMhiEasz
0f3SZTAkZGh7yxi/BTmqu6vvQ0FWYgtOJPezK19RMXistdQkA/uiQDKqeBMTLTeA
UXCnJdC05uBWhymy8DhJyryPQCJ1k3PJ+4pSmzemWIaAoQqpaH/q5yp4IAccr8wO
pxZPtddD030iVdT5oYqBoAhn2W/mKtG1fShhp7wpj/qRYecUQICocTavuFG3DK0N
k1OJ9rTxBZfnyeCBF/wdS/nNuI9xDk2WULVIya2cNu8I/te6QKp1fd4Jr3aPnZ/9
4hiw5+L2dw2z7447EwlryC4sHttjVYEDHqsedR39YNPIn55D3mfsNX2iCczk1ZDU
+OoRMiATrjILb1sOjJAs
=ytxh
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
- conversion of watchdog to DT
- usart definition for evk-pro3 board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQqm8pAAoJEAf03oE53VmQpEEH/00dsxSUrL06NzwP8Y1+UjW8
OXJPJUU0Mor/b5zCp3wsxB4+imZ4y4oqJ42qvFZjRLHj0KMvVdnxm5SNIpbQtXxV
jXPqXYk8yfH4YF3DDLuiD9wkXjwtgck7+D7ogcAIb9bbWyyGusKIcs72smvGanCd
zZrWIOGwXlqgrF5CX8kl6SIhdnYvMtee7GlzbiFHlKr4CLPOIR3iahnHR26gkzLH
cRjYVujYaHpQKBR8XvMgIl7brCUTX2KuMajvVOF8EShk8BU2MW1GHFY0cNfqaKRn
R/Z9itXk6P/h3s/Wf+Qyfpuz3E0zbS80uN/NyrIbcGbAQQIesuo8pcd9xZZ5yg0=
=whJu
-----END PGP SIGNATURE-----
Merge tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
More DT material for AT91:
- conversion of watchdog to DT
- usart definition for evk-pro3 board
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: evk-pro3: enable watchdog
ARM: at91/dts: add at91sam9_wdt driver to at91sam926x, at91sam9g45
watchdog: at91sam9_wdt: add device tree support
ARM: at91: dt: evk-pro3: enable uart0 and uart2
Also the driver was modifued to take advantage of recent improvements in
matrix_keypad_build_keymap() implementation, which automatically allocates
memory for keymap.
The driver was tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCmwSAACgkQGxsu9jQV9nbssgCcChzwuFlPkP4sVdTtAGGh5mWD
rNcAn3PfG1ByMR57GkDtdQiAjS5N2dME
=Pi49
-----END PGP SIGNATURE-----
Merge tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner SoC support for 3.8
* tag 'tags/sunxi-support-for-3.8' of git://github.com/mripard/linux:
ARM: sunxi: Add entry to MAINTAINERS
ARM: sunxi: Add device tree for the A13 and the Olinuxino board
ARM: sunxi: Add earlyprintk support
ARM: sunxi: Add basic support for Allwinner A1x SoCs
irqchip: sunxi: Add irq controller driver
clocksource: sunxi: Add Allwinner A1X Timer Driver
clk: sunxi: Add dummy fixed rate clock for Allwinner A1X SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
Their stock ticker is 3407.T which wouldn't make a good DT vendor
prefix. Use the company name initials instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch adds a device tree vendor prefix for Synopsys Inc.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Now that the Armada 370/XP platform has gained proper integration with
the clock framework, we add clk support in the Marvell Armada 370/XP
Ethernet driver.
Since the existing Device Tree binding that exposes a
'clock-frequency' property has never been exposed in any stable kernel
release, we take the freedom of removing this property to replace it
with the standard 'clocks' clock pointer property.
The Device Tree binding documentation is updated accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch finally adds a Device Tree binding to the mv_xor
driver. Thanks to the previous cleanup patches, the Device Tree
binding is relatively simply: one DT node per XOR engine, with
sub-nodes for each XOR channel of the XOR engine. The binding
obviously comes with the necessary documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree-discuss@lists.ozlabs.org
This driver allows to provide DT clocks for clock gates found on
Marvell Dove and Kirkwood SoCs. The clock gates are referenced by
the phandle index of the corresponding bit in the clock gating control
register to ease lookup in the datasheet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add Armada 370/XP specific CPU clocks
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds Device Nodes for SATA and SATA PHY device.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
[kgene.kim@samsung.com: removed address definitions as per comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In order to start upstreaming Broadcom SoC support, create
a starting hierarchy, arch and dts files.
The first support SoC family that is planned is the
BCM281XX (BCM11130/11140/11351/28145/28155) family of dual A9 mobile
SoC cores.
This code is just the skeleton code for get the machine upstreamed. It
has been made MULTIPLATFORM compatible.
Next steps
----------
Upstream a basic set of drivers - sufficient for a console boot to
ramdisk. These will includer timer, gpio, i2c drivers.
After this basic set, we will proceed with a more comprehensive set
of drivers for the 281XX SoC family.
v2 patch mods
--------
- Remove l2x0_of_init call as there were problems with the code.
A separate patch will be submitted with cache init code
- Rename capri files and refs to bcm281xx-based names
- Add bcm281xx binding doc
- various misc cleanups
v3 patch mods
-------------
- Remove extra #include lines
- Remove remaining references to capri
- dt uart chipset string added
- cleaned up chip # references
v4 patch mods
-------------
- swap order of compatible definitions for uart
- fix typo
v5 patch mods
-------------
- Rename bcm281xx to bcm11351 in dts+code,
leaving references to bcm281xx only in help+comments.
v6 patch mods
-------------
- fix typo in uart 'compatible' string
Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/FbB
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
These changes add DT boot support to DaVinci DA850
SoC.
* tag 'davinci-for-v3.8/dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850: generate dtbs for da850 boards
ARM: davinci: add support for am1808 based EnBW CMC board
ARM: davinci: da850 evm: add DT data
ARM: davinci: da850: add SoC DT data
ARM: davinci: da850: add DT boot support
ARM: davinci: da8xx: add DA850 PRUSS support
ARM: davinci: add platform hook to fetch the SRAM pool
ARM: davinci: da850: changed SRAM allocator to shared ram.
ARM: davinci: sram: switch from iotable to ioremapped regions
uio: uio_pruss: replace private SRAM API with genalloc
ARM: davinci: serial: provide API to initialze UART clocks
ARM: davinci: convert platform code to use clk_prepare/clk_unprepare
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting through a device tree, the kernel cpu logical id map can be
initialized using device tree data passed by FW or through an embedded blob.
This patch adds a function that parses device tree "cpu" nodes and
retrieves the corresponding CPUs hardware identifiers (MPIDR).
It sets the possible cpus and the cpu logical map values according to
the number of CPUs defined in the device tree and respective properties.
The device tree HW identifiers are considered valid if all CPU nodes contain
a "reg" property, there are no duplicate "reg" entries and the DT defines a
CPU node whose "reg" property matches the MPIDR[23:0] of the boot CPU.
The primary CPU is assigned cpu logical number 0 to keep the current convention
valid.
Current bindings documentation is included in the patch:
Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.
The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds device tree support for charging algorithm driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for ab8500-charger driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds device tree support for battery-temperature-monitor driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- This patch adds device tree support for fuelgauge driver
- optimize bm devices platform_data usage and of_probe(...)
Note: of_probe() routine for battery managed devices is made
common across all bm drivers.
- test status:
- interrupt numbers assigned differs between legacy and FDT mode.
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch extends the driver with any necessary SoC-specific
definitions to support EXYNOS4X12 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Based on AT91 PIT DT patch from Jean-Christophe PLAGNIOL-VILLARD.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
SPEAr platform provides a provision to control chipselects of ARM PL022
Prime Cell spi controller through its system registers, which otherwise
remains under PL022 control which some protocols do not want.
This commit intends to provide the spi chipselect control in software over
gpiolib interface. spi chip drivers can use the exported gpiolib interface to
define their chipselect through DT or platform data.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This hooks the Integrator/CP into the SoC bus when booting from
device tree, by mapping the CP controller registers first,
then registering the SoC device, and then populating the device
tree with the SoC device as parent.
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra RTC maintains seconds and milliseconds counters, and five alarm
registers. The alarms and other interrupts may wake the system from
low-power state.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra timer provides a number of 29-bit timer channels, a single
32-bit free running counter, and in the Tegra30 variant, 5 watchdog modules.
The first two channels may also trigger a legacy watchdog reset.
Define a DT binding for this HW module, and add the module into the Tegra
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use a better name for the USB PHY clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There are also a few imx6 improvement patches in there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQpeRkAAoJEFBXWFqHsHzOHMoH/3pxLWMHlaFFN70gm33GIEpj
6/P0afKhjEseQDfbvLPfRPwHTQIkw/xQ2rfSrZGUnhgAGN2SfOcxiREFpdChgqyb
b5kO+3oQpnQTFce6tuqCI8j4LAqr63AHhJPWZuDEBaR52Vs0i9gYr2Zwv7i+iUh7
fuLu+NDQLKOkEW7W97FRFVWKRGmSMhJYvhNn+kgleFUhvzUKpJ6n7kFsT05BSl97
EiJHtVxOv+RtlFvx7jrTr18NM2i4Kb4IzEfLzgYOowK9cwfNuhnaxsQvAUiGSa+z
EuvXdKN2btW0PtqHVBPdz5T0OzTyJheaCETKTqz0XM32/SVz5Ma3gZEEDagGLiw=
=zBAI
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
It's based on imx/multiplatform branch. Most of them are dts changes.
There are also a few imx6 improvement patches in there.
* tag 'imx-dt-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: select ARM and PL310 errata
ARM: imx6q: print silicon version on boot
ARM i.MX dts: Consistently add labels to devicenodes
ARM: dts: imx6q-sabresd: add volume up/down gpio keys
ARM: dts: imx53: pinctl update
ARM: imx: enable cpufreq for imx6q
ARM: dts: imx6q: enable snvs lp rtc
ARM: dts: imx6q-sabreauto: Add basic support
ARM: imx6q: let users input debug uart port number
ARM: dts: imx53-qsb: Make DA9053 regulator functional
ARM: dts: imx53-qsb: Use pinctrl for gpio-led
ARM i.MX dtsi: Add default bus-width property for esdhc controller
Signed-off-by: Arnd Bregmann <arnd@arndb.de>
From Michal Simek <michal.simek@xilinx.com>:
These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CFfP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for 3.8
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
Add device tree file for the armadeus apf27
ARM i.MX: Add Ka-Ro TX25 devicetree
ARM i.MX25: Add devicetree
ARM i.MX25: Add devicetree support
ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
based on imx-multiplatform branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=P3UZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX SoC updates
based on imx-multiplatform branch.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX51 babbage: Add display support
ARM i.MX6: Add IPU support
ARM i.MX51: Add IPU support
ARM i.MX53: Add IPU support
ARM i.MX5: switch IPU clk support to devicetree bindings
ARM i.MX6: fix ldb_di_sel mux
ARM i.MX51: setup MIPI during startup
mx2_camera: Fix regression caused by clock conversion
ARM: clk-imx27: Add missing clock for mx2-camera
ARM i.MX27: Fix low reference clock path
ARM: dts: imx27-3ds: Remove local watchdog inclusion
watchdog: Support imx watchdog on SOC_IMX53
ARM: mach-imx: Support for DryIce RTC in i.MX53
ARM : i.MX27 : split code for allocation of ressources of camera and eMMA
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested on an at91sam9260 board (evk-pro3)
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Only we meet the following conditions, we can enable the DMA support for
auart:
(1) We enable the DMA support in the dts file, such as
arch/arm/boot/dts/imx28.dtsi.
(2) We enable the hardware flow control.
(3) We use the mx28, not the mx23. Due to hardware bug(see errata: 2836),
we can not add the DMA support to mx23.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch contains a new network driver for the network unit of the
ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B
processor, a Marvell-developed ARM core that implements the ARMv7
instruction set.
Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery),
the network unit in Armada 370 and Armada XP is highly different. This
is the reason why this new 'mvneta' driver is needed, while the older
ARM Marvell SoCs use the 'mv643xx_eth' driver.
Here is an overview of the most important hardware changes that
require a new, specific, driver for the network unit of Armada 370/XP:
- The new network unit has a completely different design and layout
for the RX and TX descriptors. They are now organized as a simple
array (each RX and TX queue has base address and size of this
array) rather than a linked list as in the old SoCs.
- The new network unit has a different RXQ and TXQ management: this
management is done using special read/write counter registers,
while in the Old SocS, it was done using the Ownership bit in RX
and TX descriptors.
- The new network unit has different interrupt registers
- The new network unit way of cleaning of interrupts is not done by
writing to the cause register, but by updating per-queue counters
- The new network unit has different GMAC registers (link, speed,
duplex configuration) and different WRR registers.
- The new network unit has lots of new units like PnC (Parser and
Classifier), PMT, BM (Memory Buffer Management), xPON, and more.
The driver proposed in the current patch only handles the basic
features. Additional hardware features will progressively be supported
as needed.
This code has originally been written by Rami Rosen
<rosenr@marvell.com>, and then reviewed and cleaned up by Thomas
Petazzoni <thomas.petazzoni@free-electrons.com>.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers. There are two reasons to have a separate
driver rather than including it inside the MAC driver itself:
*) The MDIO interface is shared by all Ethernet ports, so a driver
must guarantee non-concurrent accesses to this MDIO interface. The
most logical way is to have a separate driver that handles this
single MDIO interface, used by all Ethernet ports.
*) The MDIO interface is the same between the existing mv643xx_eth
driver and the new mvneta driver. Even though it is for now only
used by the mvneta driver, it will in the future be used by the
mv643xx_eth driver as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: David S. Miller <davem@davemloft.net>
linux,mtd-name allow to specify the mtd name for retro capability with
physmap-flash drivers as boot loader pass the mtd partition via the old
device name physmap-flash.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
[wsa: fixed some whitespace]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
convert at91sam9g20ek with wm8731 to device tree support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.
SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This driver supports GRCAN and CRHCAN CAN controllers available in the GRLIB
VHDL IP core library.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enhance the driver to support partition subnodes inside the nand
device bindings to describe partions on the nand device.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
various .dts files, and timer related changes to allow
configuring the timer via device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=59qq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:
Device tree related changes for omaps updating the
various .dts files, and timer related changes to allow
configuring the timer via device tree.
* tag 'omap-for-v3.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (48 commits)
usb: musb: dsps: dt binding - add resources, example
ARM: dts: omap4-sdp: Add pinmux configuration for HDMI
ARM: dts: omap4-panda: Add pinmux configuration for HDMI
ARM: dts: Makefile: Add the am335x-evmsk target in dtbs list
ARM: dts: AM33XX: Add usbss node
ARM: dts: AM33XX: Add push-buttons device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-keys to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-evmsk
ARM: dts: AM33XX: Add pinmux configuration for gpio-leds to EVMSK
ARM: dts: AM33XX: Add user-leds device tree data to am335x-bone
ARM: dts: AM33XX: Add pinmux configuration for user-leds to BONE
ARM: dts: AM33XX: Add volume-keys device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for volume-keys to EVM
ARM: dts: AM33XX: Add matrix keypad device tree data to am335x-evm
ARM: dts: AM33XX: Add pinmux configuration for matrix keypad to EVM
ARM: dts: omap5-evm: LPDDR2 memory device details for EVM
ARM: dts: omap5: EMIF device tree data for OMAP5 boards
ARM: dts: omap5-evm: Fix size of memory defined for EVM
ARM: OMAP2+: Add device-tree support for 32kHz counter
ARM: OMAP: Add DT support for timer driver
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This driver is based on the thermal management framework in thermal_sys.c. A
thermal zone device is created with the trip points to which cooling devices
can be bound, the current cooling device is cpufreq, e.g. CPU frequency is
clipped down to cool the CPU, and other cooling devices can be added and bound
to the trip points dynamically. The platform specific PRCMU interrupts are
used to active thermal update when trip points are reached.
Signed-off-by: hongbo.zhang <hongbo.zhang@linaro.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Francesco Lavra <francescolavra.fl@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Instead of having a host of different register offsets in the device tree,
this patch simplifies the CPSW code by letting the driver set the proper
register offsets automatically, based on the CPSW version.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide simplified models for the necessary clocks on the zynq-7000
platform. Currently, the PLLs, the CPU clock network, and the basic
peripheral clock networks (for SDIO, SMC, SPI, QSPI, UART) are modelled.
OF bindings are also provided and documented.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
A selection of voltage or current values (AKA states) should always
be specified when using a GPIO regulator. If there are no switchable
states then the fixed regulators should be used instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
0384e90b8 ("spi/mcspi: allow configuration of pin directions") did what
it claimed to do the wrong way around. D0/D1 is configured as output by
*clearing* the bits in the conf registers, hence also breaking the
former default behaviour.
Fix this before that change is merged to mainline.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
NVIDIA's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add the spi driver for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Wrong description in binding document.
Doc use "gpio-enable", but code use "enable-gpio"
In drivers/regulator/gpio-regulator.c
config->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0);
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Patches from Roland Stigge <stigge@antcom.de>:
Platform topic branch for lpc32xx
* 'lpc32xx/core' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Add the motor PWM clock
ARM: LPC32xx: Cleanup irq.c
ARM: LPC32xx: Relocate calls to irq_set_chained_handler()
ARM: LPC32xx: Remove superfluous irq_alloc_descs()
Includes an update to v3.7-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a i.MX25 dtsi file along with the i.MX25 clock tree
documentation. The devicetree should be fairly complete for:
- uart
- fec
- i2c
- spi
- pwm
- nand
- gpio
- wdog
- esdhc
- flexcan
The more exotic devices currently miss clock bindings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tr2i
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB musb merge from Felipe:
"usb: musb: patches for v3.8 merge window
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read."
Here we add the required documentation for the STMPE Multi-Functional
Device (MFD) Device Tree bindings. It describes all of the bindings
currently supported by the driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
pinctrl subsystem needs gpio chip base to prepare set of gpio
pin ranges, which a given pinctrl driver can handle. This is
important to handle pinctrl gpio request calls in order to
program a given pin properly for gpio operation.
As gpio base is allocated dynamically during gpiochip
registration, presently there exists no clean way to pass this
information to the pinctrl subsystem.
After few discussions from [1], it was concluded that may be
gpio controller reporting the pin range it supports, is a
better way than pinctrl subsystem directly registering it.
[1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
[Edited documentation a bit]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The used vendor prefix corresponds to the stock symbol (ONNN) for ON
Semiconductor Corp.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
remove linux specific references, enumerates all supported
regulators
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DT bindings normally use '-' (hyphens) instead of '_' (underscore),
driver has it the proper way, but binding documentation does not
reflect it, fix it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQlr0MAAoJEHm+PkMAQRiGLVQH/171fUorGn+u2k7dNhSWJXHB
pPy6MbZhuBWepgRZGS0ffiC5tBvQaf9iK9Fh/9aqrDDw2aELk0CLPqQcfAUF/Jzf
USPdBSIMNikgZtlWhabxuj/zKdaw8UuiJpCf3rMyIRmjQgmZyw/53TEqF54xTv0I
Y4Y21vTSVXilQwvwYvcsCEBFrTZqXjLWQ60Hk+QRS9GV7a9m2LFcdiPOtRv17gbd
CBDuiMHN9R04l2bB+5WHHsu+TNNf5uy3wAgEskDTftneXWjW44R4UR8O0rQh1ezQ
Pa5WpCyJRRG8UOtPKTS6LEbljBwLLIoVI2JRoJrWoy3OkT63wyowFXyLGWCCrHY=
=qAGi
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc4' into next to sync up Wacom bits
Linux 3.7-rc4
OMAP2+ family of devices are now obtaining resources via DT, earlier
it was obtained from hwmod. Update binding document accrodingly, while
at it add example.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add atmel-ssc for device tree support
Match "atmel,at91rm9200-ssc" for using pdc for data transfer
Match "atmel,at91sam9g45-ssc" for using dma for data transfer
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
From Lee Jones:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500: (31 commits)
ARM: ux500: Convert DT_MACHINE_START to use SMP operations
ARM: ux500: CONFIG: Enable GPIO Regulators
ARM: ux500: Change the type of interrupt to something compatible
ARM: ux500: Add node for the MMC GPIO regulator
ARM: ux500: List DT compatibility using platform names rather than by board
ARM: ux500: Remove duplicate DT_MACHINE_START - make u8500 for generic
ARM: ux500: Rename references to the ccu9540 dev board accordingly
ARM: ux500: Enable all MMC devices on the u9540 when booting with DT
ARM: ux500: Enable SDI4 port on the u9540 when booting with Device Tree
ARM: ux500: Add UART support to the u9540 Device Tree
ARM: ux500: Add support for ST-Ericsson's u9540 SoC
ARM: ux500: Add skeleton DTS file for the u9540
ARM: ux500: Remove unused board compatible string
ARM: ux500: Supply the STMPE keypad Device Tree node to the STUIB DT
ARM: ux500: Apply a Device Tree node for the STMPE MFD
ARM: ux500: Stop informing the regulator subsystem that we have full constraints
ARM: ux500: Add all bu21013 touch screen components to supported Device Trees
ARM: ux500: Stop calling the UIB init function when using Device Tree
ARM: ux500: Create a new Device Tree include file for boards supporting STUIBs
Documentation: Detail permitted DT properties for the BU21013 Touch Screen
...
