We realized when we broke acpi=ht
http://bugzilla.kernel.org/show_bug.cgi?id=14886
that acpi=ht is not needed on this box
and folks have been using acpi=force on it anyway.
Signed-off-by: Len Brown <len.brown@intel.com>
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When hotadd new cpu to system, if its affinitive node is online,
should map the cpu to its own node. Otherwise, let kernel select one
online node for the new cpu later.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <4B6AAA39.6000300@linux.intel.com>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need to fall back from logical-flat APIC mode to physical-flat mode
when we have more than 8 CPUs. However, in the presence of CPU
hotplug(with bios listing not enabled but possible cpus as disabled cpus in
MADT), we have to consider the number of possible CPUs rather than
the number of current CPUs; otherwise we may cross the 8-CPU boundary
when CPUs are added later.
32bit apic code can use more cleanups (like the removal of vendor checks in
32bit default_setup_apic_routing()) and more unifications with 64bit code.
Yinghai has some patches in works already. This patch addresses the boot issue
that is reported in the virtualization guest context.
[ hpa: incorporated function annotation feedback from Yinghai Lu ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1265767304.2833.19.camel@sbs-t61.sc.intel.com>
Acked-by: Shaohui Zheng <shaohui.zheng@intel.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
cleanup only.
setup_arch(), doesn't care care if ACPI initialization succeeded
or failed, so delete acpi_boot_table_init()'s return value.
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce kernel parameter acpi_sleep=sci_force_enable
some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.
We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of the function in $subject are
exactly the same.
Also, since the arch-specific implementations of setting _PDC have
been completely hollowed out, remove the empty shells.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The only thing arch-specific about calling _PDC is what bits get
set in the input obj_list buffer.
There's no need for several levels of indirection to twiddle those
bits. Additionally, since we're just messing around with a buffer,
we can simplify the interface; no need to pass around the entire
struct acpi_processor * just to get at the buffer.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Both x86 and ia64 initialize _PDC with mostly common bit settings.
Factor out the common settings and leave the arch-specific ones alone.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of arch_acpi_processor_init_pdc()
are almost exactly the same. The only difference is in what bits
they set in obj_list buffer.
Combine the boilerplate memory management code, and leave the
arch-specific bit twiddling in separate implementations.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch dependent helper function that tells us if we should attempt to
evaluate _PDC on this machine or not.
The x86 implementation assumes that the CPUs in the machine must be
homogeneous, and that you cannot mix CPUs of different vendors.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock by skipping the fake
ARB_DISABLE.
The cpu model id on one laptop is 14. If we disable ARB_DISABLE on this box,
the box can't be booted correctly. But if we still enable ARB_DISABLE on this
box, the box can be booted correctly.
So we still use the ARB_DISABLE for the cpu which mode id is less than 0x0f.
http://bugzilla.kernel.org/show_bug.cgi?id=14700
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Pallipadi, Venkatesh <venkatesh.pallipadi@intel.com>
cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
In commit 0de51088e6, we introduced the
use of acpi-cpufreq on VIA/Centaur CPU's by removing a vendor check for
VENDOR_INTEL. However, as it turns out, at least the Nano CPU's also
need the PDC (processor driver capabilities) handshake in order to
activate the methods required for acpi-cpufreq.
Since arch_acpi_processor_init_pdc() contains another vendor check for
Intel, the PDC is not initialized on VIA CPU's. The resulting behavior
of a current mainline kernel on such systems is: acpi-cpufreq
loads and it indicates CPU frequency changes. However, the CPU stays at
a single frequency
This trivial patch ensures that init_intel_pdc() is called on Intel and
VIA/Centaur CPU's alike.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Always save the value of EFER, regardless of the state of NX. Since
EFER may not actually exist, use rdmsr_safe() to do so.
v2: check the return value from rdmsr_safe() instead of relying on
the output values being unchanged on error.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@tuxonice.net>
LKML-Reference: <1258154897-6770-3-git-send-email-hpa@zytor.com>
Acked-by: Kees Cook <kees.cook@canonical.com>
Instead of using bootmem, try find_e820_area()/reserve_early(),
and call acpi_reserve_memory() early, to allocate the wakeup
trampoline code area below 1M.
This is more reliable, and it also removes a dependency on
bootmem.
-v2: change function name to acpi_reserve_wakeup_memory(),
as suggested by Rafael.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AFA210B.3020207@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Older binutils breaks if ASSERT() is used without a sink
for the output.
For example 2.14.90.0.6 is known to be broken, the link
fails with:
LD .tmp_vmlinux1
ld:arch/x86/kernel/vmlinux.lds:678: parse error
Document this quirk in all three files that use it.
See: http://marc.info/?l=linux-kbuild&m=124930110427870&w=2
See[2]: d2ba8b2 ("x86: Fix assert syntax in vmlinux.lds.S")
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e9a63a4e55.
This breaks older binutils, where sink-less asserts are broken.
See this commit for further details:
d2ba8b2: x86: Fix assert syntax in vmlinux.lds.S
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The linker scripts grew some use of weirdly wrong linker script syntax.
It happens to work, but it's not what the syntax is documented to be.
Clean it up to use the official syntax.
Signed-off-by: Roland McGrath <roland@redhat.com>
CC: Ian Lance Taylor <iant@google.com>
Don't disable ARB_DISABLE when the familary ID is 0x0F.
http://bugzilla.kernel.org/show_bug.cgi?id=14211
This was a 2.6.31 regression, and so this patch
needs to be applied to 2.6.31.stable
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge reason: the SFI (Simple Firmware Interface) feature in the ACPI
tree needs this cleanup, pull it into the APIC branch as
well so that there's no interactions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some IO-APIC routines are ACPI specific now, but need to
be exposed when CONFIG_ACPI=n for the benefit of SFI.
Remove #ifdef ACPI around these routines:
io_apic_get_unique_id(int ioapic, int apic_id);
io_apic_get_version(int ioapic);
io_apic_get_redir_entries(int ioapic);
Move these routines from ACPI-specific boot.c to io_apic.c:
uniq_ioapic_id(u8 id)
mp_find_ioapic()
mp_find_ioapic_pin()
mp_register_ioapic()
Also, since uniq_ioapic_id() is now no longer static,
re-name it to io_apic_unique_id() for consistency
with the other public io_apic routines.
For simplicity, do not #ifdef the resulting code ACPI || SFI,
thought that could be done in the future if it is important
to optimize the !ACPI !SFI IO-APIC x86 kernel for size.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
x86 arch support for remapping HPET MSI's by associating the HPET timer block
with the interrupt-remapping HW unit and setting up appropriate irq_chip
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.630510000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch_acpi_processor_cleanup_pdc() in x86 and ia64 results in memory allocated
for _PDC objects that is never freed and will cause memory leak in case of
physical CPU remove and add. Patch fixes the memory leak by freeing the
objects soon after _PDC is evaluated.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enable gcov profiling of the entire kernel on x86_64. Required changes
include disabling profiling for:
* arch/kernel/acpi/realmode and arch/kernel/boot/compressed:
not linked to main kernel
* arch/vdso, arch/kernel/vsyscall_64 and arch/kernel/hpet:
profiling causes segfaults during boot (incompatible context)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move
arch/x86/kernel/acpi/boot.c: acpi_parse_mcfg()
to
arch/x86/pci/mmconfig-shared.c: pci_parse_mcfg()
where it is used, and make it static.
Move associated globals and helper routine with it.
No functional change.
This code move is in preparation for SFI support,
which will allow the PCI code to find the MCFG table
on systems which do not support ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One of the numbers in arch/x86/kernel/acpi/sleep.c is long, but it is
not annotated appropriately, so sparese warns about it. Fix that.
[rjw: added the changelog.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix the fact that the IOAPIC version number in the x86_64 code path always
gets assigned to 0, instead of the correct value.
Before the patch: (from "dmesg" output):
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 <---
After the patch:
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 <---
History:
io_apic_get_version() was compiled out of the x86_64 code path in the commit
f2c2cca3ac:
Author: Andi Kleen <ak@suse.de>
Date: Tue Sep 26 10:52:37 2006 +0200
[PATCH] Remove APIC version/cpu capability mpparse checking/printing
ACPI went to great trouble to get the APIC version and CPU capabilities
of different CPUs before passing them to the mpparser. But all
that data was used was to print it out. Actually it even faked some data
based on the boot cpu, not on the actual CPU being booted.
Remove all this code because it's not needed.
Cc: len.brown@intel.com
At the time, the IOAPIC version number was deliberately not printed
in the x86_64 code path. However, after the x86 and x86_64 files were
merged, the net result is that the IOAPIC version is printed incorrectly
in the x86_64 code path.
The patch below provides a fix. I have tested it with acpi, and with
acpi=off, and did not see any problems.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <20090416014230.4885.94926.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
*************************
ARB_DISABLE is a NOP on all of the recent Intel platforms.
For such platforms, reduce contention on c3_lock
by skipping the fake ARB_DISABLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len expressed concern that the update_mptable feature has
side-effects on the ACPI code.
Make it sure explicitly that the code only ever gets called if
the (default disabled) update_mptable boot quirk option is
disabled.
[ Impact: isolate the update_mptable feature from ACPI code more ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A0DC832.5090200@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.
So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.
v2: io_apic_irq ==> irq_attr
triggering ==> trigger
v3: add set_io_apic_irq_attr
[ Impact: cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prepare to call setup_io_apic_routing() in pcibios_irq_enable()
also remove not needed member apic_id.
[ Impact: clean up, prepare for future change ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C3DD.3050104@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch to call mp_config_acpi_gsi() from the ACPI IRQ registration
code never got mainline because there were open discussions about it.
This call is needed to properly update the kernel's copy of the mptable,
when the update_mptable boot parameter is needed.
Now that the dust has settled with the APIC unification, and since there
were no objections when the patch was re-submitted, try this again.
[ Impact: fix the update_mptable boot parameter ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A01C387.7090103@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.
[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new interfaces (not yet used)
For all the platforms out there, there is an infinite number of buggy
BIOSes. This adds infrastructure to treat BIOS interrupts more like
toxic waste and "glove box" them -- we switch out the register set,
perform the BIOS interrupt, and then restore the previous state.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
All logical processors with APIC ID values of 255 and greater will have their
APIC reported through Processor X2APIC structure (type-9 entry type) and all
logical processors with APIC ID less than 255 will have their APIC reported
through legacy Processor Local APIC (type-0 entry type) only. This is the
same case even for NMI structure reporting.
The Processor X2APIC Affinity structure provides the association between the
X2APIC ID of a logical processor and the proximity domain to which the logical
processor belongs.
For OSPM, Procssor IDs outside the 0-254 range are to be declared as Device()
objects in the ACPI namespace.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.
Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In general, the only definitions that assembly files can use
are in _types.S headers (where available), so convert them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
Add mp_find_ioapic_pin() to find an IO APIC's specific pin from a GSI,
and use this function within acpi/boot. Make it non-static so other
code can use it too.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
to prevent wrongly overwriting fixmap that still want to use.
ACPI used to rely on low mappings being all linearly mapped and
grew a habit: it never really unmapped certain kinds of tables
after use.
This can cause problems - for example the hypothetical case
when some spurious access still references it.
v2: remove prev_map and prev_size in __apci_map_table
v3: let acpi_os_unmap_memory() call early_iounmap too, so remove extral calling to
early_acpi_os_unmap_memory
v4: fix typo in one acpi_get_table_with_size calling
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On x86, __acpi_map_table uses early_ioremap() to create the mapping,
replacing the previous mapping with a new one. Once enough of the
kernel is up an running it switches to using normal ioremap(). At
that point, we need to clean up the final mapping to avoid a warning
from the early_ioremap subsystem.
This can be removed after all the instances in the ACPI code are fixed
that rely on early-ioremap's implicit overmapping of previously
mapped tables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Always map acpi tables, rather than assuming we can use the normal
linear mapping to access the acpi tables. This is necessary in a
virtual environment where the linear mappings are to pseudo-physical
memory, but the acpi tables exist at a real physical address. It
doesn't hurt to map in the normal non-virtual case, so just do it
unconditionally.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
__acpi_map_table() effectively reimplements early_ioremap(). Rather
than have that duplication, just implement it in terms of
early_ioremap().
However, unlike early_ioremap(), __acpi_map_table() just maintains a
single mapping which gets replaced each call, and has no corresponding
unmap function. Implement this by just removing the previous mapping
each time its called. Unfortunately, this will leave a stray mapping
at the end.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
just like 64 bit switch from flat logical APIC messages to
flat physical mode automatically.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: refactor code
x86 subarchitectures each defined a "acpi_madt_oem_check()" method,
which could be an inline function, or an extern, or a static function,
and which was also the name of a genapic field.
Untangle this namespace spaghetti by setting ->acpi_madt_oem_check()
to NULL on those subarchitectures that have no detection quirks,
and rename the other ones (summit, es7000) that do.
Also change default_acpi_madt_oem_check() to handle NULL entries,
and clean its control flow up as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix two compilation warnings in drivers/acpi/sleep.c, one triggered
by unsetting CONFIG_SUSPEND and the other triggered by unsetting
CONFIG_HIBERNATION, by moving some code under the appropriate
#ifdefs .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Do the following cleanups:
* kill x86_64_init_pda() which now is equivalent to pda_init()
* use per_cpu_offset() instead of cpu_pda() when initializing
initial_gs
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Based on original patch from Christoph Lameter and Mike Travis. ]
CPU startup code in head_64.S loaded address of a zero page into %gs
for temporary use till pda is loaded but address to the actual pda is
available at the point. Load the real address directly instead.
This will help unifying percpu and pda handling later on.
This patch is mostly taken from Mike Travis' "x86_64: Fold pda into
per cpu area" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
[IA64] fix typo in cpumask_of_pcibus()
x86: fix x86_32 builds for summit and es7000 arch's
cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
cpumask: use cpumask_var_t in acpi-cpufreq.c
cpumask: use work_on_cpu in acpi/cstate.c
cpumask: convert struct cpufreq_policy to cpumask_var_t
cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
x86: cleanup remaining cpumask_t ops in smpboot code
cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
cpumask: update local_cpus_show to use new cpumask API
ia64: cpumask fix for is_affinity_mask_valid()
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The Cx Register address obtained from the _CST object is used as the MWAIT
hints if the register type is FFixedHW. And it is used to check whether
the Cx type is supported or not.
On some boxes the following Cx state package is obtained from _CST object:
>{
ResourceTemplate ()
{
Register (FFixedHW,
0x01, // Bit Width
0x02, // Bit Offset
0x0000000000889759, // Address
0x03, // Access Size
)
},
0x03,
0xF5,
0x015E }
In such case we should use the bit[7:4] of Cx address to check whether
the Cx type is supported or not.
mask the MWAIT hint to avoid array address overflow
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by:Venki Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: use new cpumask API to reduce stack usage
Replace the saving of current->cpus_allowed and set_cpus_allowed_ptr() with
a work_on_cpu function for the acpi_processor_ffh_cstate_probe() function.
Basically splits acpi_processor_ffh_cstate_probe() into two functions, the
other being acpi_processor_ffh_cstate_probe_cpu which is the work function
run on the designated cpu.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce stack size, use new API.
Replace cpumask_t with cpumask_var_t.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Reduce future system panics due to cpumask operations using NR_CPUS
Insure that code does not look at bits >= nr_cpu_ids as when cpumasks are
allocated based on nr_cpu_ids, these extra bits will not be defined.
Also some other minor updates:
* change in to use cpu accessor function set_cpu_present() instead of
directly accessing cpu_present_map w/cpu_clear() [arch/x86/kernel/reboot.c]
* use cpumask_of() instead of &cpumask_of_cpu() [arch/x86/kernel/reboot.c]
* optimize some cpu_mask_to_apicid_and functions.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When ACPI is asked to find an MADT (APIC table)
and fails, then ACPI expects to run in PIC mode.
However, if an MP Table is was found, IRQs will be
registered as if an IOAPIC is being used, even
though ACPI is configuring interrupt links links for PIC mode.
In this scenario, disable MPS so that IRQs
are registered in PIC mode, consistent with ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=12257
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines it may be necessary to disable the saving/restoring
of the ACPI NVS memory region during hibernation/resume. For this
purpose, introduce new ACPI kernel command line option
acpi_sleep=s4_nonvs.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
reorder exit path in __get_smp_config().
also move two print outs to acpi_process_madt
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix section mismatch warning - apic_x2apic_phys
x86: fix section mismatch warning - apic_x2apic_cluster
x86: fix section mismatch warning - apic_x2apic_uv_x
x86: fix section mismatch warning - apic_physflat
x86: fix section mismatch warning - apic_flat
x86: memtest fix use of reserve_early()
x86 syscall.h: fix argument order
x86/tlb_uv: remove strange mc146818rtc include
x86: remove redundant KERN_DEBUG on pr_debug
x86: do_boot_cpu - check if we have ESR register
x86: MAINTAINERS change for AMD microcode patch loader
x86/proc: fix /proc/cpuinfo cpu offline bug
x86: call dmi-quirks for HP Laptops after early-quirks are executed
x86, kexec: fix hang on i386 when panic occurs while console_sem is held
MCE: Don't run 32bit machine checks with interrupts on
x86: SB600: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: make variables static
Impact: make warning message disappear - functionality unchanged
Problems with bogus IRQ0 override of those laptops should be fixed
with commits
x86: SB600: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
that introduce early-quirks based on chipset configuration.
For further information, see
http://bugzilla.kernel.org/show_bug.cgi?id=11516
Instead of removing the related dmi-quirks completely we'd like to
keep them for (at least) one kernel version -- to double-check whether
the early-quirks really took effect. But the dmi-quirks need to be
called after early-quirks are executed. With this patch calling
sequence for dmi-quriks is changed as follows:
acpi_boot_table_init() (dmi-quirks)
...
early_quirks() (detect bogus IRQ0 override)
...
acpi_boot_init() (late dmi-quirks and setup IO APIC)
Note: Plan is to remove the "late dmi-quirks" with next kernel version.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 ACPI: fix breakage of resume on 64-bit UP systems with SMP kernel
Introduce is_vmalloc_or_module_addr() and use with DEBUG_VIRTUAL
x86 ACPI: Fix breakage of resume on 64-bit UP systems with SMP kernel
We are now using per CPU GDT tables in head_64.S and the original
early_gdt_descr.address is invalidated after boot by
setup_per_cpu_areas(). This breaks resume from suspend to RAM on
x86_64 UP systems using SMP kernels, because this part of head_64.S
is also executed during the resume and the invalid GDT address
causes the system to crash. It doesn't break on 'true' SMP systems,
because early_gdt_descr.address is modified every time
native_cpu_up() runs. However, during resume it should point to the
GDT of the boot CPU rather than to another CPU's GDT.
For this reason, during suspend to RAM always make
early_gdt_descr.address point to the boot CPU's GDT.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11568, which
is a regression from 2.6.26.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-and-tested-by: Andy Wettstein <ajw1980@gmail.com>
for !CONFIG_HAVE_SPARSE_IRQ
fix:
In file included from arch/x86/kernel/early-quirks.c:18:
include/asm/io_apic.h: In function 'probe_nr_irqs':
include/asm/io_apic.h:209: error: 'NR_IRQS' undeclared (first use in this function)
include/asm/io_apic.h:209: error: (Each undeclared identifier is reported only once
include/asm/io_apic.h:209: error: for each function it appears in.)
v2: fix by Ingo
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Until now, NR_IRQS was derived from black magic defines that had to
be "large enough" to both accomodate NR_CPUS and MAX_NR_IO_APICs.
This resulted in a way too large irq_desc[] array on most x86 systems.
Especially with larger CPU masks, the size of irq_desc can spiral out
of control quickly.
So be smarter about it and use precise allocation instead: determine the
default maximum possible IRQ number from the ACPI MADT. Use a minimum limit
of at least 32 IRQs for broken BIOSes.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/acpi/boot.c💯 warning: 'acpi_mcfg_64bit_base_addr' defined
but not used
http://bugzilla.kernel.org/show_bug.cgi?id=11743
Signed-off-by: Pavel Vasilyev <linuxoid@tochka.ru>
Signed-off-by: Len Brown <len.brown@intel.com>
x86_64 SMP suspend to RAM uses a 10k temporary stack for saving the
kernel state, but only 4k of it is used. Shrink it to 4k.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x86_64 SMP suspend to RAM uses a 10k temporary stack for saving the
kernel state, but only 4k of it is used. Shrink it to 4k.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This merges phase 1 of the x86 tree, which is a collection of branches:
x86/alternatives, x86/cleanups, x86/commandline, x86/crashdump,
x86/debug, x86/defconfig, x86/doc, x86/exports, x86/fpu, x86/gart,
x86/idle, x86/mm, x86/mtrr, x86/nmi-watchdog, x86/oprofile,
x86/paravirt, x86/reboot, x86/sparse-fixes, x86/tsc, x86/urgent and
x86/vmalloc
and as Ingo says: "these are the easiest, purely independent x86 topics
with no conflicts, in one nice Octopus merge".
* 'x86-v28-for-linus-phase1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (147 commits)
x86: mtrr_cleanup: treat WRPROT as UNCACHEABLE
x86: mtrr_cleanup: first 1M may be covered in var mtrrs
x86: mtrr_cleanup: print out correct type v2
x86: trivial printk fix in efi.c
x86, debug: mtrr_cleanup print out var mtrr before change it
x86: mtrr_cleanup try gran_size to less than 1M, v3
x86: mtrr_cleanup try gran_size to less than 1M, cleanup
x86: change MTRR_SANITIZER to def_bool y
x86, debug printouts: IOMMU setup failures should not be KERN_ERR
x86: export set_memory_ro and set_memory_rw
x86: mtrr_cleanup try gran_size to less than 1M
x86: mtrr_cleanup prepare to make gran_size to less 1M
x86: mtrr_cleanup safe to get more spare regs now
x86_64: be less annoying on boot, v2
x86: mtrr_cleanup hole size should be less than half of chunk_size, v2
x86: add mtrr_cleanup_debug command line
x86: mtrr_cleanup optimization, v2
x86: don't need to go to chunksize to 4G
x86_64: be less annoying on boot
x86, olpc: fix endian bug in openfirmware workaround
...
This PCI ID based quick should be a full solution for the IRQ0 override
related slowdown problem on SB450 based systems:
33fb0e4: x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
Emit a warning in those cases where the DMI quirk triggers but
the PCI ID based quirk didnt.
If this warning does not trigger then we can phase out the DMI quirks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
On my box it was caused by:
commit 691874fa96
Author: Maciej W. Rozycki <macro@linux-mips.org>
Date: Tue May 27 21:19:51 2008 +0100
x86: I/O APIC: timer through 8259A second-chance
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
http://marc.info/?l=linux-kernel&m=121358440508410&w=4
Matthew Garrett told us about that happening on the nx6125:
http://marc.info/?l=linux-kernel&m=121396307411930&w=4
and then Maciej analysed the breakage on the basis of a DSDT from the
nx6325:
http://marc.info/?l=linux-kernel&m=121401068718826&w=4
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acpi_mcfg_64bit_base_addr is used when CONFIG_PCI_MMCONFIG is enabled.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
after following patch,
commit 1b313f4a6d
Author: Cyrill Gorcunov <gorcunov@gmail.com>
Date: Mon Aug 18 20:45:57 2008 +0400
x86: apic - generic_processor_info
- use physid_set instead of phys_cpu and physids_or
- set phys_cpu_present_map bit AFTER check for allowed
number of processors
- add checking for APIC valid version in 64bit mode
(mostly not needed but added for merging purpose)
- add apic_version definition for 64bit mode which
is used now
we are getting warning for acpi path on 64 bit system.
make the 64-bit side fill in apic_version[] as well.
[ mingo@elte.hu: build fix ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c:24: warning: 'temp_stack' defined but not used
[ Sven Wegener <sven.wegener@stealer.net>: fix build bug ]
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SGI UV will have MMCFG base addresses that are greater than 4GB (32 bits).
v2: Use CONFIG_RESOURCES_64BIT instead of CONFIG_X86_64.
v3: Create a flag, that is set by platform specific code,
to disable the > 4GB check.
Signed-off-by: John Keller <jpk@sgi.com>
Cc: jpk@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
There are a couple of places where (P)Dprintk is used which is an old
compile time enabled printk wrapper. Convert it to the generic
pr_debug().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* This patch replaces the dangerous lvalue version of cpumask_of_cpu
with new cpumask_of_cpu_ptr macros. These are patterned after the
node_to_cpumask_ptr macros.
In general terms, if there is a cpumask_of_cpu_map[] then a pointer to
the cpumask_of_cpu_map[cpu] entry is used. The cpumask_of_cpu_map
is provided when there is a large NR_CPUS count, reducing
greatly the amount of code generated and stack space used for
cpumask_of_cpu(). The pointer to the cpumask_t value is needed for
calling set_cpus_allowed_ptr() to reduce the amount of stack space
needed to pass the cpumask_t value.
If there isn't a cpumask_of_cpu_map[], then a temporary variable is
declared and filled in with value from cpumask_of_cpu(cpu) as well as
a pointer variable pointing to this temporary variable. Afterwards,
the pointer is used to reference the cpumask value. The compiler
will optimize out the extra dereference through the pointer as well
as the stack space used for the pointer, resulting in identical code.
A good example of the orthogonal usages is in net/sunrpc/svc.c:
case SVC_POOL_PERCPU:
{
unsigned int cpu = m->pool_to[pidx];
cpumask_of_cpu_ptr(cpumask, cpu);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, cpumask);
return 1;
}
case SVC_POOL_PERNODE:
{
unsigned int node = m->pool_to[pidx];
node_to_cpumask_ptr(nodecpumask, node);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, nodecpumask);
return 1;
}
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
991528d734
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.
However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Explain that we set up the descriptors for Big Real Mode, and why we
do so. In particular, one system that is known to fail without it is
the Lenovo X61.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
also remove GET_APIC_ID when read_apic_id is used.
need to apply after
[PATCH] x86: mach_apicdef.h need to include before smp.h
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x2apic support. Interrupt-remapping must be enabled before enabling x2apic,
this is needed to ensure that IO interrupts continue to work properly after the
cpu mode is changed to x2apic(which uses 32bit extended physical/cluster
apic id).
On systems where apicid's are > 255, BIOS can handover the control to OS in
x2apic mode. Or if the OS handover was in legacy xapic mode, check
if it is capable of x2apic mode. And if we succeed in enabling
Interrupt-remapping, then we can enable x2apic mode in the CPU.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have two conflicting DMA-based quirks in there for the same set of
boxes (HP nx6325 and nx6125) and one of them actually breaks my box.
So remove the extra code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: =?iso-8859-1?q?T=F6r=F6k_Edwin?= <edwintorok@gmail.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and let 64-bit to fall back to use fixmap too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Signed-off-by: Ingo Molnar <mingo@elte.hu>
if acpi=off, acpi=noirq and pci=noacpi, we need to disable apic.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c: In function ‘acpi_save_state_mem':
arch/x86/kernel/acpi/sleep.c:75: error: ‘stack_start' undeclared (first use in this function)
arch/x86/kernel/acpi/sleep.c:75: error: (Each undeclared identifier is reported
only once
arch/x86/kernel/acpi/sleep.c:75: error: for each function it appears in.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
call x86_64's init_rsp stack_start, just as i386 does.
Put a zeroed stack segment for consistency. With this,
we can eliminate one ugly ifdef in smpboot.c.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some HP laptops have a problem with their DSDT reporting as
HP/SB400/10000, which includes some code which overrides all temperature
trip points to 16C if the INTIN2 input of the I/O APIC is enabled. This
input is incorrectly designated the ISA IRQ 0 via an interrupt source
override even though it is wired to the output of the master 8259A and
INTIN0 is not connected at all. So far two models have been identified,
namely nx6125 and nx6325.
Use a knob provided by the I/O APIC interrupt registration code to
abandon any attempts to route IRQ 0 through the I/O APIC for these
systems.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As discovered recently some systems exhibit problems when the 8254 timer
IRQ is routed through the I/O APIC. These problems do not affect the
timer IRQ itself and therefore cannot be detected when the correctness of
operation of the interrupt is verified in check_timer(). Therefore the
I/O APIC path of the timer IRQ has to be disabled entirely.
This is a change that lets platforms ask for the timer IRQ not to be
registered in the I/O APIC interrupt tables. The local APIC and ExtINTA
paths are unaffected. This request is only taken into account for ACPI
platforms as MP table systems seem unaffected so far.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
if the system doesn't have ioapic, we don't need to store entries for mptable
update
also let mp_config_acpi_gsi not call func in mpparse
so later could decouple mpparse with acpi more easily
Reported-by: Daniel Exner <dex@dragonslave.de>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Exner <dex@dragonslave.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so we don't get the same value multiple times.
also make mp_config_acpi_legacy_irqs more readable by moving assignments
together.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Daniel Exner reported IO-APIC enumeration breakage in linux-next.
Alexey Starikovskiy found out that it might be related to
commit 2944e16b25 "x86: update mptable".
use enable_update_mptable to decide if need check before add mp_irqs array.
Reported-by: Daniel Exner <webmaster@dragonslave.de>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
