sctp_wait_for_connect() currently already holds the asoc to keep it
alive during the sleep, in case another thread release it. But Andrey
Konovalov and Dmitry Vyukov reported an use-after-free in such
situation.
Problem is that __sctp_connect() doesn't get a ref on the asoc and will
do a read on the asoc after calling sctp_wait_for_connect(), but by then
another thread may have closed it and the _put on sctp_wait_for_connect
will actually release it, causing the use-after-free.
Fix is, instead of doing the read after waiting for the connect, do it
before so, and avoid this issue as the socket is still locked by then.
There should be no issue on returning the asoc id in case of failure as
the application shouldn't trust on that number in such situations
anyway.
This issue doesn't exist in sctp_sendmsg() path.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold says:
====================
net: fix device reference leaks
This series fixes a number of device reference leaks (and one of_node
leak) due to failure to drop the references taken by bus_find_device()
and friends.
Note that the final two patches have been compile tested only.
v2
- hold reference to cpsw-phy-sel device while accessing private data as
requested by David. Also update the commit message. (patch 1/4)
- add linux-omap on CC where appropriate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.
Fixes: 6fe6611ff2 ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563d ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-11-04
This series contains six hot fixes of the mlx5 core and mlx5e driver.
Huy fixed an invalid pointer dereference on initialization flow for when
the selected mlx5 load profile is out of range.
Or provided three eswitch offloads related fixes
- Prevent changing NS of a VF representor.
- Handle matching on vlan priority for offloaded TC rules
- Set the actions for offloaded rules properly
On my part I here addressed the error flow related issues in
mlx5e_open_channel reported by Jesper just this week.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When prof_sel is invalid, mlx5_core_warn is called but the
mlx5_core_dev is not initialized yet. Solution is moving the prof_sel code
after dev->pdev assignment
Fixes: 2974ab6e8b ('net/mlx5: Improve driver log messages')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the current generation of the mlx5 HW (CX4/CX4-Lx) per flow vlan
push/pop actions are emulated, we must not program them to the firmware.
Fixes: f5f8247609 ('net/mlx5: E-Switch, Support VLAN actions in the offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We ignored the vlan priority in offloaded TC rules matching part,
fix that.
Fixes: 095b6cfd69 ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF reps should be altogether on the same NS as they were created.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx5e_open_channel CQs must be created before napi is enabled.
Here we move the XDP CQ creation to satisfy that fact.
mlx5e_close_channel is already working according to the right order.
Fixes: b5503b994e ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of mlx5e_open_rq fails the error handling will jump to
label err_close_xdp_sq and will try to close the xdp_sq unconditionally.
xdp_sq is valid only in case of XDP use cases, i.e priv->xdp_prog is
not null.
To fix this in this patch we test xdp_sq validity prior to closing it.
In addition we now close the xdp_sq.cq as well.
Fixes: b5503b994e ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cgroupstats_cmd_get_policy is [CGROUPSTATS_CMD_ATTR_MAX+1],
taskstats_cmd_get_policy[TASKSTATS_CMD_ATTR_MAX+1],
but their family.maxattr is TASKSTATS_CMD_ATTR_MAX.
CGROUPSTATS_CMD_ATTR_MAX is less than TASKSTATS_CMD_ATTR_MAX,
so we could end up accessing out-of-bound.
Change cgroupstats_cmd_get_policy to TASKSTATS_CMD_ATTR_MAX+1,
this is safe because the rest are initialized to 0's.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __genl_register_family(), when genl_validate_assign_mc_groups()
fails, we forget to free the memory we possibly allocate for
family->attrbuf.
Note, some callers call genl_unregister_family() to clean up
on error path, it doesn't work because the family is inserted
to the global list in the nearly last step.
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While fuzzing kernel with syzkaller, Andrey reported a nasty crash
in inet6_bind() caused by DCCP lacking a required method.
Fixes: ab1e0a13d7 ("[SOCK] proto: Add hashinfo member to struct proto")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_v6_err() does not use pskb_may_pull() and might access garbage.
We only need 4 bytes at the beginning of the DCCP header, like TCP,
so the 8 bytes pulled in icmpv6_notify() are more than enough.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dccp_v4_err() does not use pskb_may_pull() and might access garbage.
We only need 4 bytes at the beginning of the DCCP header, like TCP,
so the 8 bytes pulled in icmp_socket_deliver() are more than enough.
This patch might allow to process more ICMP messages, as some routers
are still limiting the size of reflected bytes to 28 (RFC 792), instead
of extended lengths (RFC 1812 4.3.2.3)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After my commit, tcp_sendmsg() might restart its loop after
processing socket backlog.
If sk_err is set, we blindly return an error, even though we
copied data to user space before.
We should instead return number of bytes that could be copied,
otherwise user space might resend data and corrupt the stream.
This might happen if another thread is using recvmsg(MSG_ERRQUEUE)
to process timestamps.
Issue was diagnosed by Soheil and Willem, big kudos to them !
Fixes: d41a69f1d3 ("tcp: make tcp_sendmsg() aware of socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Tested-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b6 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Imagine initial value of max_skb_frags is 17, and last
skb in write queue has 15 frags.
Then max_skb_frags is lowered to 14 or smaller value.
tcp_sendmsg() will then be allowed to add additional page frags
and eventually go past MAX_SKB_FRAGS, overflowing struct
skb_shared_info.
Fixes: 5f74f82ea3 ("net:Add sysctl_max_skb_frags")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Cc: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates replacement buffers before-hand to make
sure whenever an aggregation begins there would be a replacement
for the Rx buffers, as we can't release the buffer until
aggregation is terminated and driver logic assumes the Rx rings
are always full.
For every other Rx page that's being allocated [I.e., regular]
the page is being completely mapped while for the replacement
buffers only the first portion of the page is being mapped.
This means that:
a. Once replacement buffer replenishes the regular Rx ring,
assuming there's more than a single packet on page we'd post unmapped
memory toward HW [assuming mapping is actually done in granularity
smaller than page].
b. Unmaps are being done for the entire page, which is incorrect.
Fixes: 55482edc25 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR_VALUE() in commit 87557efc27
("xen-netfront: do not cast grant table reference to signed short") would
not return true for error code unless we cast ref first to type int.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some IPCB fields are currently set in udp_tunnel6_xmit_skb(), which are
never used before it reaches ip6tunnel_xmit(), and past that point the
control buffer is no longer interpreted as IPCB.
This clears these unused IPCB related codes. Currently there is no skb
scrubbing in ip6_udp_tunnel, otherwise IPCB(skb)->opt might need to be
cleared for IPv4 packets, as shown in 5146d1f151
("tunnel: Clear IPCB(skb)->opt before dst_link_failure called").
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myself as a maintainer for mlx5 core driver as well.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The coalesce settings behave badly when changing just one value:
... # ethtool -c eth0
rx-usecs: 249
... # ethtool -C eth0 tx-usecs 250
... # ethtool -c eth0
rx-usecs: 248
This occurs due to rounding errors when calculating the microseconds
value - the divisons round down. This causes (eg) the rx-usecs to
decrease by one every time the tx-usecs value is set as per the above.
Fix this by making the divison round-to-nearest.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
'create_root_ns()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract unix domain socket may embed null characters,
these should be translated to '@' when printed out to
proc the same way the null prefix is currently being
translated.
This helps for tools such as netstat, lsof and the proc
based implementation in ss to show all the significant
bytes of the name (instead of getting cut at the first
null occurrence).
Signed-off-by: Isaac Boukris <iboukris@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be
set to 0, not 6, on the Qualcomm Technologies QDF2432.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian says:
====================
drivers: net: xgene: Fix coalescing bugs
This patch set fixes the following,
1. Since ethernet v1 hardware has a bug related to coalescing,
disabling this feature
2. Fixing ethernet v2 hardware, interrupt trigger region
id to 2, to kickoff coalescing
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the interrupt trigger region id to 2 and the
corresponding threshold set0/set1 values to 8/16.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethernet v1 hardware has a bug related to coalescing, disabling
this feature.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCgAaBQJYF6ANExxta2xAcGVuZ3V0cm9uaXguZGUACgkQPTuqJaypJWqQ
DAf+JRm7uhjaXEgITIhgiGIZBmCce7ONSBmBRr6cKcQyzMPaAHjfEZMcR5pltvH1
z03bspu5oug3bfSxk4iYK9hNxxAV+URxFxBDbOMdnolAsl6ZBcpOkx2jj/JFByZ5
fmOk8ChQr28qteEMLcTlm6O188eq2fZ+GUVZOh9iRslSVVcvGrM90NQoPFMUfP7G
On9+rZzSZlyNvdCSdFwrjUDzMVEW77P1Hv3gG10koefgIZKLelmMOIwDg7EvGTon
7HjqdZs6MFoSFAcbzJHB9lN0pAtK8nxWd3SPhdQof3kca8Dff/si4r5ZB2gAdSBq
w17LfdWoVE4p5/XvSyM4SM/X9A==
=Per+
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161031' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-10-31
this is a pull request of two patches for the upcoming v4.9 release.
The first patch is by Lukas Resch for the sja1000 plx_pci driver that adds
support for Moxa CAN devices. The second patch is by Oliver Hartkopp and fixes
a potential kernel panic in the CAN broadcast manager.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde1f ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: a bunch of fixes by holding transport
There are several places where it holds assoc after getting transport by
searching from transport rhashtable, it may cause use-after-free issue.
This patchset is to fix them by holding transport instead.
v1->v2:
Fix the changelog of patch 2/3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, in rx path, before calling lock_sock, it needed to
hold assoc when got it by __sctp_lookup_association, in case other place
would free/put assoc.
But in __sctp_lookup_association, it lookup and hold transport, then got
assoc by transport->assoc, then hold assoc and put transport. It means
it didn't hold transport, yet it was returned and later on directly
assigned to chunk->transport.
Without the protection of sock lock, the transport may be freed/put by
other places, which would cause a use-after-free issue.
This patch is to fix this issue by holding transport instead of assoc.
As holding transport can make sure to access assoc is also safe, and
actually it looks up assoc by searching transport rhashtable, to hold
transport here makes more sense.
Note that the function will be renamed later on on another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, it used a local variable to save the transport that is
looked up by __sctp_lookup_association(), and didn't return it back. But in
sctp_rcv, it is used to initialize chunk->transport. So when hitting this,
even if it found the transport, it was still initializing chunk->transport
with null instead.
This patch is to return the transport back through transport pointer
that is from __sctp_rcv_lookup_harder().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_transport_lookup_process(), Commit 1cceda7849 ("sctp: fix
the issue sctp_diag uses lock_sock in rcu_read_lock") moved cb() out
of rcu lock, but it put transport and hold assoc instead, and ignore
that cb() still uses transport. It may cause a use-after-free issue.
This patch is to hold transport instead of assoc there.
Fixes: 1cceda7849 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While grant reference is of type uint32_t, xen-netfront erroneously casts
it to signed short in BUG_ON().
This would lead to the xen domU panic during boot-up or migration when it
is attached with lots of paravirtual devices.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
Reference: http://marc.info/?l=linux-netdev&m=147732648731237
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Moxa CAN devices.
Signed-off-by: Lukas Resch <l.resch@incubedit.com>
Signed-off-by: Christoph Zehentner <c.zehentner@incubedit.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
iwlwifi
* some fixes for suspend/resume with unified FW images
* a fix for a false-positive lockdep report
* a fix for multi-queue that caused an unnecessary 1 second latency
* a fix for an ACPI parsing bug that caused a misleading error message
brcmfmac
* fix a variable uninitialised warning in brcmf_cfg80211_start_ap()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYFbhOAAoJEG4XJFUm622bSCYIAKjSnuc8uTAzeOp1gAajzij6
HOfJqbb2d6QX28nDjoFBkhY1tUXfk1ltAA8MaAqv8eHsOpEDN9+zXEiQZAZDCB5k
TmUYHtvK3d7QdAJKm9QdpDPUsGKoRzJdnlLVXSg2lGgyARQ1U/gohbl9ZTdsI+/e
ucEQBhjJa4OQUup4kPIXtOdUlZPQSokkqFzqUnZuHWLGDGynl5eKcSxzYr9REKbr
MH005AuZHp19+mLsSo/1+bH4Qe0K6Vq7I5uJ6jIiYW+mH58DKPPb9pBvdZ8qSugM
gd7Ju7Z6/A3pG4+61J9o4yg39KZu4LN1UmwldnU4DRO1NNliipD5slxG5sE1/hU=
=ktW5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-10-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
iwlwifi
* some fixes for suspend/resume with unified FW images
* a fix for a false-positive lockdep report
* a fix for multi-queue that caused an unnecessary 1 second latency
* a fix for an ACPI parsing bug that caused a misleading error message
brcmfmac
* fix a variable uninitialised warning in brcmf_cfg80211_start_ap()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
