Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dead code as well.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
s3c_hsotg_process_req_feature comments was not correct
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When clearing HALT on an endpoint, req->complete of in progress
requests must be called with locks off. New request should only be
started if there is not already a pending request on the endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The omap musb front-end calls into the phy driver directly
instead of using a generic phy interface, which causes a link
error when the specific driver is not built-in:
drivers/built-in.o: In function `omap2430_musb_disable':
usb/musb/omap2430.c:480: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap2430_musb_enable':
usb/musb/omap2430.c:466: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:447: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap_musb_set_mailbox':
usb/musb/omap2430.c:273: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:304: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o:(.debug_addr+0xbd9e0): more undefined references to `omap_control_usb_set_mode' follow
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36c ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple musb glue drivers depend on the generic usb phy support,
but fail to list it as a dependency in Kconfig. This results
in build erros like:
drivers/built-in.o: In function `am35x_remove':
:(.text+0xadacc): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `am35x_probe':
:(.text+0xae1c8): undefined reference to `usb_phy_generic_register'
:(.text+0xae244): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_remove':
:(.text+0xaf648): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_musb_init':
:(.text+0xaf694): undefined reference to `usb_phy_generic_register'
This adds the ones that are missing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsl udc core assumes itself always self powered, so set is_selfpowered
is 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The gadget power property will be used at get_status request.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whether the gadget is selfpowerwed or not can be determined by composite
core, so we can use a common entry to indicate if the self-powered
is supported by gadget, and the related private variable at individual
udc driver can be deleted.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 8e74475b0e (usb: dwc3: gadget: use udc-core's
reset notifier) added support for the new UDC core's
reset notifier to dwc3 but while at it, it removed
a spin_lock() from dwc3_reset_gadget() which might
cause an unbalanced spin_unlock() further down the line
Fixes: 8e74475b0e (usb: dwc3: gadget: use udc-core's reset notifier)
Cc: <stable@vger.kernel.org> # v3.19
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes we want to just print a formatted
string without passing any extra data. The
following will be used for removing reliance
on dev_vdbg() from dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if an unknown IRQ event is triggered, that means
the HW is really misbehaving. Instead of printing
a debug message, let's WARN() so users report
when that happens.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The purpose of the functions and their parametrs might not be obvious
to the reader, so explain it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first parameter of __uvcg_iter_strm_cls() is always used in
the context of struct uvcg_streaming_header, so change the
function prototype accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The RLT code has already done it, so no software operation is needed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760 driver registration function returns an error if USB is
disabled. This made sense when the driver only supported host
controllers, but now that it supports peripheral controllers host
support isn't mandatory anymore.
Fix this by returning an error only when both the HCD and UDC functions
are disabled, either through the kernel configuration or at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both isp1760_register() and isp1761_pci_probe() check whether USB is
disabled by calling usb_disabled(), and bail out with an error if it is.
One check is enough, remove the PCI-specific check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable compilation of the isp1760 driver in pure host mode, pure device
mode, or dual-role mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that this is DRD, it doesn't make sense to keep it under
drivers/usb/host.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ISP1761 is a dual-mode host and device controller backward
compatible on the host side with the ISP1760. Add support for the device
controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Configuring the mode of operation of port 1 doesn't belong to the HCD
code, as it's related to the soon to come UDC support. Move the
configuration to core code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although the corresponding register is part of the HCD register space,
processor bus initialization is not specific to the HCD. To prepare for
device controller support, move bus interface initialization to core
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The IRQF_SHARED flag needs to be set regardless of the bus type. Don't
require glue code to set it manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move core device initialization to a central location in order to share
it with the device mode implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The isp1760-rhcd.h header contains PTD constants and structures only
useful for the HCD implementation. It also contains register definitions
that will be needed by common code when implementing support for the
ISP1761 device controller, but doesn't contain the isp1760_hcd structure
definition that will also be used by common code.
Move definitions to the right location and create an isp1760-regs.h to
store register definitions. No change other than moving definitions and
modifying indentation is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The slotinfo and memory_chunk structures are specific to the driver and
defined in a header file. Prefix them with isp1760_ to avoid namespace
clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
