Use regmap for local caching and for multi-byte operations to be able
to use regmap API functions and to reduce the need for locking in the
driver.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip IDs are not used by the driver. Drop them. Use driver data to
store the limit register resolution instead, and use this information
when writing temperature limits to improve chip specific rounding and
to avoid writing into unused register bits.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking three configuration register bits and the manufacturer ID
register to auto-detect LM92 is a bit vague. Repeat twice on replicated
register addresses to improve detection accuracy. Check the manufacturer
ID first and bail out immediately without reading the other register if
there is a mismatch to reduce the number of i2c transfers needed in that
case. Also explicitly test for an error from reading the configuration
register to avoid potential situations where the returned error masked
against 0xe0 is 0.
While at it, drop "lm92: Found National Semiconductor LM92 chip" detection
noise.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20240731191312.1710417-13-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature reading function was using a signed long for the ADC
code, which could lead to mishandling of invalid codes on 32-bit
platforms. This allowed out-of-range ADC codes to be incorrectly
interpreted as valid values and used in temperature calculations.
Change adc_code to u32 to ensure that invalid ADC codes are correctly
identified on all platforms.
Fixes: 1b2ca93cd0 ("hwmon: Add driver for Astera Labs PT5161L retimer")
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Message-ID: <20240819104630.2375441-1-chou.cosmo@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
X570-E GAMING does not have VRM temperature sensor.
Signed-off-by: Ross Brown <true.robot.ross@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20240730062320.5188-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Bail out immediately if reading any of the registers used for chip
detection fails, or if it returns an unexpected value. Drop all log
messages from detection code.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip supports reading and writing the conversion rate.
Add support for the update_interval sysfs attribute.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert driver to with_info hwmon API to simplify the code and
with it its maintainability.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for local caching, to hide register read/write address
differences, and for multi-byte operations. With this change,
the driver specific lock is no longer necessary.
While at it, check errors seen when initializing the chip and bail out
if chip initialization fails.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Bit 0, 5, and 6 in the status register are reserved and, if set, do not
indicate an alarm. Bit 7 is the 'busy' bit and also does not indicate
an alarm. Mask the non-alarm bits to avoid reporting them to userspace.
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Module test code reports underflows when writing sensor limits.
temp2_min: Suspected underflow: [min=-77000, read 101000, written -2147483648]
temp2_max: Suspected underflow: [min=-77000, read 101000, written -2147483648]
temp2_crit: Suspected underflow: [min=-77000, read 101000, written -2147483648]
Clamp temperature ranges when writing limits to fix the problem.
While at it, use sign_extend32() when reading temperatures to make
the code easier to understand.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In the MAX6581 datasheet Revision 0 to 3, the local channel overtemperature
status is reported in bit 6 of register 0x45, and the overtemperature
status for remote channel 7 is reported in bit 7. In Revision 4 and later,
the local channel overtemperature status is reported in bit 7, and the
remote channel 7 overtemperature status is reported in bit 6. A real
chip was found to match the functionality documented in Revision 4 and
later.
The code was fixed with commit 1ea3fd1eb9 ("hwmon: (max6697) Fix swapped
temp{1,8} critical alarms"). At that time it looked like this was an
original bug. It only turned out later that the problem was the result of
incorrect information in the chip datasheet.
Document the discrepancy to avoid confusion caused by old versions of the
datasheet.
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use with_info API to simplify the code and to reduce its size.
This patch reduces object file size by approximately 25%.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only difference between supported chips is the number of channels.
Drop enum chips and list the number of channels in struct i2c_device_id
directly.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for caching to simplify the code and to hide read/write
register address differences.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use bit macro to make the code easier to understand and reduce duplication.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files to alphabetic order to simplify driver maintenance.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the device property APIs so the driver does not depend on OF to
work.
While at it, properly include mod_devicetable for struct of_device_id
and fix some parameter alignment in the changed places.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240726-dev-hwmon-ltc6947-fw-agnostic-v1-1-f7d6cab7d438@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default the PWM duty cycle in hardware is 100%. On some systems this
can cause unwanted fan noise. Add the ability to specify the fan
connections and initial state of the PWMs via device properties.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20240722221737.3407958-4-chris.packham@alliedtelesis.co.nz
[groeck: Cleaned up formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6581 supports setting the minimum temperature as well as minimum
temperature alarms. Add support for it.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to with_info hwmon API to simplify the code and reduce its size.
This patch reduces object file size by approximately 25%.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for register caching, and use regmap API for bit operations
to simplify the code.
This patch reduces object file size by approximately 10%.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Platform data is not used anywhere in the upstram kernel.
Drop support for it to simplify code maintenance.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files to alphabetic order to improve maintainability.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chips reporting overcurrent alarms report it in the second alarm register.
That means the second alarm register has to be read, even if the chip only
supports 8 or fewer ADC channels.
MAX16067 and MAX16068 report undervoltage and overvoltage alarms in
separate registers. Fold register contents together to report both with
the existing alarm attribute. This requires actually storing the chip type
in struct max16065_data. Rename the variable 'chip' to match the variable
name used in the probe function.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Fixes: f5bae2642e ("hwmon: Driver for MAX16065 System Manager and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing large limits resulted in overflows as reported by module tests.
in0_lcrit: Suspected overflow: [max=5538, read 0, written 2147483647]
in0_crit: Suspected overflow: [max=5538, read 0, written 2147483647]
in0_min: Suspected overflow: [max=5538, read 0, written 2147483647]
Fix the problem by clamping prior to multiplications and the use of
DIV_ROUND_CLOSEST, and by using consistent variable types.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Fixes: f5bae2642e ("hwmon: Driver for MAX16065 System Manager and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The iterated nodes are direct children of the device node, and the
`device_for_each_child_node()` macro accounts for child node
availability.
`fwnode_for_each_available_child_node()` is meant to access the child
nodes of an fwnode, and therefore not direct child nodes of the device
node.
In this case, the child nodes are not required outside the loop, and
the scoped version of the macro can be used to remove the repetitive
`goto put` pattern.
Use `device_for_each_child_node_scoped_scoped()` to indicate device's
direct child nodes.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240721-device_for_each_child_node-available-v2-2-f33748fd8b2d@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations to simplify the code
and to reduce dependency on locking.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233/LM95234 support enabling temperature channels one by one.
Add support for tempX_enable attribute to be able to use that
functionality.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to with_info API to simplify the code and reduce its size.
This patch reduces the object file size by about 30%.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap to replace local caching and to be able to use regmap API
functions.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use find_closest() instead of manually coding it to find best update
interval.
Since find_closest() uses rounding to find the best match, the resulting
update interval will now reflect the update interval that is closest to
the requested value, not the value that is lower or equal to the requested
value.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Alphabetic include file order simplifies maintenance and makes it easier
to add or remove files.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size.
No functional changes.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional changes.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional changes.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional changes.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional changes.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use multi-byte regmap operations where possible to reduce code size
and the need for mutex protection.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new PCI device IDs into the root IDs and miscellaneous IDs lists to
provide support for the latest generation of AMD 1Ah family 60h processor
models.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Link: https://lore.kernel.org/r/20240722092801.3480266-1-Shyam-sundar.S-k@amd.com
This just standardizes the use of MIN() and MAX() macros, with the very
traditional semantics. The goal is to use these for C constant
expressions and for top-level / static initializers, and so be able to
simplify the min()/max() macros.
These macro names were used by various kernel code - they are very
traditional, after all - and all such users have been fixed up, with a
few different approaches:
- trivial duplicated macro definitions have been removed
Note that 'trivial' here means that it's obviously kernel code that
already included all the major kernel headers, and thus gets the new
generic MIN/MAX macros automatically.
- non-trivial duplicated macro definitions are guarded with #ifndef
This is the "yes, they define their own versions, but no, the include
situation is not entirely obvious, and maybe they don't get the
generic version automatically" case.
- strange use case #1
A couple of drivers decided that the way they want to describe their
versioning is with
#define MAJ 1
#define MIN 2
#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN)
which adds zero value and I just did my Alexander the Great
impersonation, and rewrote that pointless Gordian knot as
#define DRV_VERSION "1.2"
instead.
- strange use case #2
A couple of drivers thought that it's a good idea to have a random
'MIN' or 'MAX' define for a value or index into a table, rather than
the traditional macro that takes arguments.
These values were re-written as C enum's instead. The new
function-line macros only expand when followed by an open
parenthesis, and thus don't clash with enum use.
Happily, there weren't really all that many of these cases, and a lot of
users already had the pattern of using '#ifndef' guarding (or in one
case just using '#undef MIN') before defining their own private version
that does the same thing. I left such cases alone.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit systems,
have been in linux-next for a while with no reported issues. The
Kconfig fixup went in 29 hours ago, so might have missed the latest
linux-next, but was acked by everyone involved.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppR4w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwoQCeIaW3nbOiNTmOupvEnZwrN3yVNs8An3Q5L+Br
1LpTASaU6A8pN81Z1m5g
=6U1z
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc and other driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit
systems, have been in linux-next for a while with no reported issues.
The Kconfig fixup went in 29 hours ago, so might have missed the
latest linux-next, but was acked by everyone involved"
* tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
misc: Kconfig: exclude mrvl-cn10k-dpi compilation for 32-bit systems
misc: delete Makefile.rej
binder: fix hang of unregistered readers
misc: Kconfig: add a new dependency for MARVELL_CN10K_DPI
virtio: add missing MODULE_DESCRIPTION() macro
agp: uninorth: add missing MODULE_DESCRIPTION() macro
spmi: add missing MODULE_DESCRIPTION() macros
dev/parport: fix the array out-of-bounds risk
samples: configfs: add missing MODULE_DESCRIPTION() macro
misc: mrvl-cn10k-dpi: add Octeon CN10K DPI administrative driver
misc: keba: Fix missing AUXILIARY_BUS dependency
slimbus: Fix struct and documentation alignment in stream.c
MAINTAINERS: CC dri-devel list on Qualcomm FastRPC patches
misc: fastrpc: use coherent pool for untranslated Compute Banks
misc: fastrpc: support complete DMA pool access to the DSP
misc: fastrpc: add missing MODULE_DESCRIPTION() macro
misc: fastrpc: Add missing dev_err newlines
misc: fastrpc: Use memdup_user()
nvmem: core: Implement force_ro sysfs attribute
nvmem: Use sysfs_emit() for type attribute
...
they're the only ones who can interpret the results properly
- The usual cleanups and fixes, left and right
-----BEGIN PGP SIGNATURE-----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=rd6Q
-----END PGP SIGNATURE-----
Merge tag 'x86_misc_for_v6.11_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 updates from Borislav Petkov:
- Make error checking of AMD SMN accesses more robust in the callers as
they're the only ones who can interpret the results properly
- The usual cleanups and fixes, left and right
* tag 'x86_misc_for_v6.11_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kmsan: Fix hook for unaligned accesses
x86/platform/iosf_mbi: Convert PCIBIOS_* return codes to errnos
x86/pci/xen: Fix PCIBIOS_* return code handling
x86/pci/intel_mid_pci: Fix PCIBIOS_* return code handling
x86/of: Return consistent error type from x86_of_pci_irq_enable()
hwmon: (k10temp) Rename _data variable
hwmon: (k10temp) Remove unused HAVE_TDIE() macro
hwmon: (k10temp) Reduce k10temp_get_ccd_support() parameters
hwmon: (k10temp) Define a helper function to read CCD temperature
x86/amd_nb: Enhance SMN access error checking
hwmon: (k10temp) Check return value of amd_smn_read()
EDAC/amd64: Check return value of amd_smn_read()
EDAC/amd64: Remove unused register accesses
tools/x86/kcpuid: Add missing dir via Makefile
x86, arm: Add missing license tag to syscall tables files
* Obsolete driver removals
- Removed obsolete adm1021 and max6642 drivers
* New drivers
- MPS MP2891
- MPS MP2993
- MPS MP9941
- MPS MP5920
- SPD5118 (Temperature Sensor and EEPROM)
* Added device support to existing drivers
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
* Notable enhancements and fixes
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827 drivers
* Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=ebWS
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
* New
- Add "cros_ec_hwmon" driver to expose fan speed and temperature.
- Add "cros_charge-control" driver to control charge thresholds and
behaviour.
- Add module parameter "log_poll_period_ms" in cros_ec_debugfs for
tuning the poll period.
- Support version 3 of EC_CMD_GET_NEXT_EVENT and keyboard matrix.
* Fixes
- Fix a race condition in accessing MEC (Microchip EC) memory between
ACPI and kernel. Serialize the memory access by an AML (ACPI
Machine Language) mutex.
- Fix an issue of wrong EC message version in cros_ec_debugfs.
* Misc
- Fix kernel-doc errors and cleanups.
-----BEGIN PGP SIGNATURE-----
iIkEABYKADEWIQS0yQeDP3cjLyifNRUrxTEGBto89AUCZo04zBMcdHp1bmdiaUBr
ZXJuZWwub3JnAAoJECvFMQYG2jz0bf0BAOjE7APATFsKLuFmtKxk/1XlsspsRTWK
vocdNAKuj9I5AQCdcrHcDreLz5ldqodCpOc4TXiZoLHIkELNQcQtOorhDw==
=To8o
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Tzung-Bi Shih:
"New code:
- Add "cros_ec_hwmon" driver to expose fan speed and temperature
- Add "cros_charge-control" driver to control charge thresholds and
behaviour
- Add module parameter "log_poll_period_ms" in cros_ec_debugfs for
tuning the poll period
- Support version 3 of EC_CMD_GET_NEXT_EVENT and keyboard matrix
Fixes:
- Fix a race condition in accessing MEC (Microchip EC) memory between
ACPI and kernel. Serialize the memory access by an AML (ACPI
Machine Language) mutex
- Fix an issue of wrong EC message version in cros_ec_debugfs
Misc:
- Fix kernel-doc errors and cleanups"
* tag 'tag-chrome-platform-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (28 commits)
power: supply: cros_charge-control: Fix signedness bug in charge_behaviour_store()
power: supply: cros_charge-control: Avoid accessing attributes out of bounds
power: supply: cros_charge-control: don't load if Framework control is present
power: supply: add ChromeOS EC based charge control driver
platform/chrome: cros_ec_proto: Introduce cros_ec_get_cmd_versions()
platform/chrome: Update binary interface for EC-based charge control
ACPI: battery: add devm_battery_hook_register()
dt-bindings: input: cros-ec-keyboard: Add keyboard matrix v3.0
platform/chrome: cros_ec_lpc: Handle zero length read/write
platform/chrome: cros_ec_lpc: Fix error code in cros_ec_lpc_mec_read_bytes()
platform/chrome: cros_ec_debugfs: fix wrong EC message version
platform/chrome: cros_ec_proto: update Kunit test for get_next_data_v3
platform/chrome: cros_ec_proto: add missing MODULE_DESCRIPTION() macro
hwmon: (cros_ec) Fix access to restricted __le16
hwmon: (cros_ec) Prevent read overflow in probe()
platform/chrome: cros_ec_lpc: Add quirks for Framework Laptop
platform/chrome: cros_ec_lpc: Add a new quirk for AML mutex
platform/chrome: cros_ec_lpc: Add a new quirk for ACPI id
platform/chrome: cros_ec_lpc: MEC access can use an AML mutex
platform/chrome: cros_ec_lpc: MEC access can return error code
...
The critical alarm bit for the local temperature sensor (temp1) is in
bit 7 of register 0x45 (not bit 6), and the critical alarm bit for remote
temperature sensor 7 (temp8) is in bit 6 (not bit 7).
This only affects MAX6581 since all other chips supported by this driver
do not support those critical alarms.
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using DIV_ROUND_CLOSEST() on an unbound value can result in underflows.
Indeed, module test scripts report:
temp1_max: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
temp1_crit: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
Fix by introducing an extra set of clamping.
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding support for G761 included adding support for an internal clock.
Enabling the internal clock requires setting a bit in the FAN_CMD2
register. This is implemented in g762_fan_init(). However, g762_fan_init()
is called before clock support is selected, and the flag indicating that
the internal clock should be used is not yet set.
Initialize the clock before initializing the fan to solve the problem.
While at it, also add "g7621" to the i2c_device_id array.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Fixes: 6ce402327a ("hwmon: g672: add support for g761")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMC6821 supports configuring if a fan is DC or PWM controlled.
Add support for the pwm1_mode attribute to make it runtime configurable.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use with_info API to simplify the code and make it easier
to maintain. This also reduces code size by approximately 20%.
No functional change intended.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for register accesses and caching.
While at it, use sysfs_emit() instead of sprintf() to write sysfs
attribute data, and remove spurious debug messages which would only
be seen as result of a bug in the code. Also make sure that error
codes are propagated and not replaced with -EIO.
While at it, introduce rounding of written temperature values and for
internal calculations to reduce deviation from written values and as
much as possible.
No functional change intended except for differences introduced by
rounding.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver only supports a single chip, so an enum
to determine the chip type is unnecessary. Drop it.
No functional change intended.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use BIT() and GENMASK() for bit and mask definitions
to help distinguish bit and mask definitions from other
defines and to make the code easier to read.
No functional change intended.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using tabs for column alignment makes the code easier to read.
No functional change intended.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files to alphabetic order to simplify maintenance,
and drop the unnecessary kernel.h include.
No functional change intended.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After setting fan1_target and setting pwm1_enable to 4,
the fan controller tries to achieve the requested fan speed.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip does not have a fan divisor. What it does have is a configuration
to set either 2 or 4 pulses per fan rotation. Rename the attribute to
reflect its use. Update documentation accordingly.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The default value of the maximum fan speed limit register is 0,
essentially translating to an unlimited fan speed. When reading
the limit, a value of 0 is reported in this case. However, writing
a value of 0 results in writing a value of 0xffff into the register,
which is inconsistent.
To solve the problem, permit writing a limit of 0 for the maximim fan
speed, effectively translating to "no limit". Write 0 into the register
if a limit value of 0 is written. Otherwise limit the range to
<1..6000000> and write 1..0xffff into the register. This ensures that
reading and writing from and to a limit register return the same value
while at the same time not changing reported values when reading the
speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing
a negative limit does not make sense and should be reported instead of
being corrected.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm value range is well defined from 0..255. Don't accept any values
outside this range.
This changes the valid range of pwm1_auto_point2_pwm from 0..254 to 0..255,
meaning it can now be equivalent to not only pwm1_auto_point1_pwm (which is
always 0) but also to pwm1_auto_point3_pwm (which is always 255). While
that may not be practical, there seems to be no technical reason for
preventing a user from doing it.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
DIV_ROUND_CLOSEST() after kstrtol() results in an underflow if a large
negative number such as -9223372036854775808 is provided by the user.
Fix it by reordering clamp_val() and DIV_ROUND_CLOSEST() operations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2991_T_INT_CH_NR is 4. The st->temp_en[] array has LTC2991_MAX_CHANNEL
(4) elements. Thus if "channel" is equal to LTC2991_T_INT_CH_NR then we
have read one element beyond the end of the array. Flip the conditions
around so that we check if "channel" is valid before using it as an array
index.
Fixes: 2b9ea4262a ("hwmon: Add driver for ltc2991")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/Zoa9Y_UMY4_ROfhF@stanley.mountain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The big one here is we finally have Paul Cercueil's (and others)
DMA buffer support for IIO devices enabling high speed zero
copy transfer of data to and from sensors supported by IIO (and for
example USB). This should aid with upstream support of a range of
higher performance ADCs and DACs.
Two merges from other trees
- spi/spi_devm_optimize used for simplification in ad7944.
- dmaengine/topic_dma_vec to enable the DMABUF series.
One feature with impact outside IIO.
- Richer set of dev_err_probe() like helpers to cover ERR_PTR() cases.
New device support
==================
adi,ad7173
- Add support for AD4111, AD4112, AD4114, AD4115 and ADC4116 pseudo
differential ADCs. Major driver rework was needed to enabled these.
adi,ad7944
- Use devm_spi_optimize_message() to avoid a local devm cleanup
callback. This is the example case from the patch set, others will
follow.
mediatek,mt6359-auxadc
- New driver for this ADC IP found in MT6357, MT6358 and MT6359 PMICs.
st,accel
- Add support for the LIS2DS12 accelerometer
ti,ads1119
- New driver for this 16 bit 2-differential or 4-single ended channel
ADC.
Features
========
dt-bindings
- Introduce new common-mode-channel property to help handle pseudo
differential ADCs where we have something that looks like one side
of differential input, but which is only suited for use with a
slow moving reference.
adi,adf4350
- Support use as a clock provider.
iio-hmwon
- Support reading of labels from IIO devices by their consumers and
use this in the hwmon bridge.
Cleanup and minor fixes
=======================
Treewide
- Use regmap_clear_bits() / regmap_set_bits() to simplify open coded
equivalents.
- Use devm_regulator_get_enable_read_voltage() to replace equivalent
opencoded boilerplate. In some cases enabled complete conversion to
devm handling and removal of explicit remove() callbacks.
- Introduce dev_err_ptr_probe() and other variants and make use of
of them in a couple of examples driver cleanups. Will find use in
many more drivers soon.
adi,ad7192
- Introduce local struct device *dev and use dev_err_probe() to give
more readable code.
adi,adi-axi-adc/dac
- Improved consistency of messages using dev_err_probe()
adi,adis
- Split the trigger handling into cases that needed paging and those that
don't resulting in more readable code.
- Use cleanup.h to simplify error paths via scoped cleanup.
- Add adis specific lock helpers and make use of them in a number of drivers.
adi,ad7192
- Update maintainer (Alisa-Dariana Roman)
adi,ad7606
- dt-binding cleanup.
avago,apds9306
- Add a maintainer entry (Subhajit Ghosh)
linear,ltc2309
- Fix a wrong endian type.
st,stm32-dfsdm
- Fix a missing port property in the dt-binding.
st,sensors
- Relax whoami match failure to a warning print rather than probe failure.
This enables fallback compatibles to existing parts from those that don't
necessarily even exit yet.
-----BEGIN PGP SIGNATURE-----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=+9tp
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.11b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 2nd set of new device support, features and cleanup for 6.11
The big one here is we finally have Paul Cercueil's (and others)
DMA buffer support for IIO devices enabling high speed zero
copy transfer of data to and from sensors supported by IIO (and for
example USB). This should aid with upstream support of a range of
higher performance ADCs and DACs.
Two merges from other trees
- spi/spi_devm_optimize used for simplification in ad7944.
- dmaengine/topic_dma_vec to enable the DMABUF series.
One feature with impact outside IIO.
- Richer set of dev_err_probe() like helpers to cover ERR_PTR() cases.
New device support
==================
adi,ad7173
- Add support for AD4111, AD4112, AD4114, AD4115 and ADC4116 pseudo
differential ADCs. Major driver rework was needed to enabled these.
adi,ad7944
- Use devm_spi_optimize_message() to avoid a local devm cleanup
callback. This is the example case from the patch set, others will
follow.
mediatek,mt6359-auxadc
- New driver for this ADC IP found in MT6357, MT6358 and MT6359 PMICs.
st,accel
- Add support for the LIS2DS12 accelerometer
ti,ads1119
- New driver for this 16 bit 2-differential or 4-single ended channel
ADC.
Features
========
dt-bindings
- Introduce new common-mode-channel property to help handle pseudo
differential ADCs where we have something that looks like one side
of differential input, but which is only suited for use with a
slow moving reference.
adi,adf4350
- Support use as a clock provider.
iio-hmwon
- Support reading of labels from IIO devices by their consumers and
use this in the hwmon bridge.
Cleanup and minor fixes
=======================
Treewide
- Use regmap_clear_bits() / regmap_set_bits() to simplify open coded
equivalents.
- Use devm_regulator_get_enable_read_voltage() to replace equivalent
opencoded boilerplate. In some cases enabled complete conversion to
devm handling and removal of explicit remove() callbacks.
- Introduce dev_err_ptr_probe() and other variants and make use of
of them in a couple of examples driver cleanups. Will find use in
many more drivers soon.
adi,ad7192
- Introduce local struct device *dev and use dev_err_probe() to give
more readable code.
adi,adi-axi-adc/dac
- Improved consistency of messages using dev_err_probe()
adi,adis
- Split the trigger handling into cases that needed paging and those that
don't resulting in more readable code.
- Use cleanup.h to simplify error paths via scoped cleanup.
- Add adis specific lock helpers and make use of them in a number of drivers.
adi,ad7192
- Update maintainer (Alisa-Dariana Roman)
adi,ad7606
- dt-binding cleanup.
avago,apds9306
- Add a maintainer entry (Subhajit Ghosh)
linear,ltc2309
- Fix a wrong endian type.
st,stm32-dfsdm
- Fix a missing port property in the dt-binding.
st,sensors
- Relax whoami match failure to a warning print rather than probe failure.
This enables fallback compatibles to existing parts from those that don't
necessarily even exit yet.
* tag 'iio-for-6.11b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (112 commits)
iio: adc: ad7173: Fix uninitialized symbol is_current_chan
iio: adc: Add support for MediaTek MT6357/8/9 Auxiliary ADC
math.h: Add unsigned 8 bits fractional numbers type
dt-bindings: iio: adc: Add MediaTek MT6359 PMIC AUXADC
iio: common: scmi_iio: convert to dev_err_probe()
iio: backend: make use of dev_err_cast_probe()
iio: temperature: ltc2983: convert to dev_err_probe()
dev_printk: add new dev_err_probe() helpers
iio: xilinx-ams: Add labels
iio: adc: ad7944: use devm_spi_optimize_message()
Documentation: iio: Document high-speed DMABUF based API
iio: buffer-dmaengine: Support new DMABUF based userspace API
iio: buffer-dma: Enable support for DMABUFs
iio: core: Add new DMABUF interface infrastructure
MAINTAINERS: Update AD7192 driver maintainer
iio: adc: ad7192: use devm_regulator_get_enable_read_voltage
iio: st_sensors: relax WhoAmI check in st_sensors_verify_id()
MAINTAINERS: Add AVAGO APDS9306
dt-bindings: iio: adc: adi,ad7606: comment and sort the compatible names
dt-bindings: iio: adc: adi,ad7606: add missing datasheet link
...
Add support for MPS Hot-Swap controller mp5920. This driver exposes
telemetry and limit value readings and writings.
Signed-off-by: Alex Vdovydchenko <xzeol@yahoo.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240702115252.981416-3-xzeol@yahoo.com
[groeck: Use min_t() to limit length of displayed model string]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the comments on fan is disabled, we change to manual mode
and set the duty cycle to 0.
For setting the duty cycle part, the register is wrong. Fix it.
Fixes: 1c301fc539 ("hwmon: Add a driver for the ADT7475 hardware monitoring chip")
Signed-off-by: Wayne Tung <chineweff@gmail.com>
Link: https://lore.kernel.org/r/20240701073252.317397-1-chineweff@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configuration register bit 5 must read 0 for all JC42.4 compliant chips.
Several capability register bits must be set for all TSE2004 compliant
chips. Use that information to strengthen the detect function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TSE2004av standardizes the device ID of compliant temperature sensors to
be 0x22xx, where xx is the device revision. Use a single define for all
TSE2004av compliant temperature sensors, and relax the device id mask to
match the upper 8 bit of the device id register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add labels from IIO channels to our channels. This allows userspace to
display more meaningful names instead of "in0" or "temp5".
Although lm-sensors gracefully handles errors when reading channel
labels, the ABI says the label attribute
> Should only be created if the driver has hints about what this voltage
> channel is being used for, and user-space doesn't.
Therefore, we test to see if the channel has a label before
creating the attribute.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20240624174601.1527244-3-sean.anderson@linux.dev
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of rescaling power channels after the fact, use the dedicated
scaling API. This should reduce any inaccuracies resulting from the
scaling.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240620212005.821805-1-sean.anderson@linux.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The SPD5118 specification says, in its documentation of the page bits
in the MR11 register:
"
This register only applies to non-volatile memory (1024) Bytes) access of
SPD5 Hub device.
For volatile memory access, this register must be programmed to '000'.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"
Renesas/ITD SPD5118 hub controllers take this literally and disable access
to volatile memory if the page selected in MR11 is != 0. Since the BIOS or
ROMMON will access the non-volatile memory and likely select a page != 0,
this means that the driver will not instantiate since it can not identify
the chip. Even if the driver instantiates, access to volatile registers
is blocked after a nvram read operation which selects a page other than 0.
To solve the problem, add initialization code to select page 0 during
probe. Before doing that, use basic validation to ensure that this is
really a SPD5118 device and not some random EEPROM.
Cc: Sasha Kozachuk <skozachuk@google.com>
Cc: John Hamrick <johnham@google.com>
Cc: Chris Sarra <chrissarra@google.com>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using regmap for paging significantly improves caching since the regmap
cache no longer needs to be cleared after changing the page, so let's
use it.
Suggested-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update peci subsystem to use the same vendor-family-model
combined definition that core x86 code uses.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20240529171920.62571-1-tony.luck@intel.com
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Update hwmon init with info instead of group. The hwmon info structure
in more flexible to describe sensor attribute & easy to maintian.
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Link: https://lore.kernel.org/r/20240614055533.2735210-1-naresh.solanki@9elements.com
[groeck: Replace clamp_val() with range check when writing pwmX_input]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The INA230 has an Alert pin which is asserted when the alert
function selected in the Mask/Enable register exceeds the
value programmed into the Alert Limit register. Assertion is based
on the Alert Polarity Bit (APOL, bit 1 of the Mask/Enable register).
It is default set to value 0 i.e Normal (active-low open collector).
However, hardware can be designed in such a way that expects Alert pin
to become active high if a user-defined threshold in Alert limit
register has been exceeded. This patch adds a way to pass alert polarity
value to the driver via device tree.
Signed-off-by: Amna Waseem <Amna.Waseem@axis.com>
Link: https://lore.kernel.org/r/20240611-apol-ina2xx-fix-v4-2-8df1d2282fc5@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
...to address the following warning:
drivers/hwmon/k10temp.c:104:9:
warning: macro is not used [-Wunused-macros]
No functional change is intended.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240606-fix-smn-bad-read-v4-7-ffde21931c3f@amd.com
Currently, k10temp_get_ccd_support() takes as input "pdev" and "data". However,
"pdev" is already included in "data". Furthermore, the "pdev" parameter is no
longer used in k10temp_get_ccd_support(), since its use was moved into
read_ccd_temp_reg().
Drop the "pdev" input parameter as it is no longer needed.
No functional change is intended.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240606-fix-smn-bad-read-v4-6-ffde21931c3f@amd.com
The CCD temperature register is read in two places. These reads are done
using an AMD SMN access, and a number of parameters are needed for the
operation.
Move the SMN access and parameter gathering into a helper function in order to
simplify the code flow. This also has a benefit of centralizing the hardware
register access in a single place in case fixes or special decoding is required.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240606-fix-smn-bad-read-v4-5-ffde21931c3f@amd.com
Check the return value of amd_smn_read() before saving a value. This
ensures invalid values aren't saved or used.
There are three cases here with slightly different behavior:
1) read_tempreg_nb_zen():
This is a function pointer which does not include a return code.
In this case, set the register value to 0 on failure. This
enforces Read-as-Zero behavior.
2) k10temp_read_temp():
This function does have return codes, so return the error code
from the failed register read. Continued operation is not
necessary, since there is no valid data from the register.
Furthermore, if the register value was set to 0, then the
following operation would underflow.
3) k10temp_get_ccd_support():
This function reads the same register from multiple CCD
instances in a loop. And a bitmask is formed if a specific bit
is set in each register instance. The loop should continue on a
failed register read, skipping the bit check.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240606-fix-smn-bad-read-v4-3-ffde21931c3f@amd.com
Commit ac0c26bae6 ("hwmon: (lm25066) Use i2c_get_match_data()") changed
enum chips to start with 1 instead of 0, under the assumption that
the data pointer in of_device_id must not start with 0 (NULL) if
i2c_get_match_data() is used. However, that is perfectly fine as long as
there is also an i2c_device_id array with the same data which is used
as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 10a0575ea0 ("hwmon: (nct6775-i2c) Use i2c_get_match_data()")
introduced calling i2c_get_match_data() to the nct6775 driver. As part
of that commit, enum kinds was changed to start with 1, based on
Adjust the 'kinds' enum to not use 0, so that no match data can be
distinguished from a valid enum value.
The patch had to be fixed later with commit 2792fc8f8c ("hwmon:
(nct6775-core) Explicitly initialize nct6775_device_names indexes") and
commit efe86092ab ("hwmon: (nct6775-platform) Explicitly initialize
nct6775_sio_names indexes").
Various patches submitted later show that the change from 0 to 1 is
not really necessary. As it turns out, it is perfectly fine as long as
there is an i2c_device_id array with the same data as in the of_device_id
array. This data is used as fallback if the data pointer in struct
of_device_id is NULL (0).
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Earlier it was assumed that the data pointer in of_device_id must not start
with 0 (NULL) if i2c_get_match_data() is used. However, it turns out that
this is perfectly fine as long as there is also an i2c_device_id array with
the same data, which is used as fallback in that case.
Let enum chips start with 0 to avoid confusion against other drivers
where the enum starts with 0 and i2c_get_match_data() is used as well.
While doing that, remove chip_id from struct mp2856_data since it is only
used in the probe function, and typecast the result of i2c_get_match_data()
to kernel_ulong_t to avoid the double typecast.
Cc: Peter Yin <peteryin.openbmc@gmail.com>
Cc: Potin Lai <potin.lai.pt@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a driver calls device_get_match_data(), the .data pointer in its id
data structures must not be NULL/0 because device_get_match_data()
returns NULL if an entry is not found. Explain that in a comment to avoid
confusion why this is required in this driver but not in other drivers.
Cc: Daniel Matyas <daniel.matyas@analog.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With SPD5118 chip detection for the most part handled by the i2c-smbus
core using DMI information, the spd5118 driver no longer needs to
auto-detect spd5118 compliant chips.
Auto-detection by the driver is still needed on systems with no DMI support
or on systems with more than eight DIMMs and can not be removed entirely.
However, it affects boot time and introduces the risk of mis-identifying
chips. Add configuration option to be able to disable it on systems where
chip detection is handled outside the driver.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for reading SPD NVMEM data from SPD5118 (Jedec JESD300)
compliant memory modules. NVMEM write operation is not supported.
NVMEM support is optional. If CONFIG_NVMEM is disabled, the driver will
still instantiate but not provide NVMEM attribute files.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add suspend/resume support to ensure that limit and configuration
registers are updated and synchronized after a suspend/resume cycle.
Cc: Armin Wolf <W_Armin@gmx.de>
Cc: Stephen Horvath <s.horvath@outlook.com.au>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/asus_atk0110.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/corsair-cpro.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/hwmon/mr75203.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-hwmon-v1-1-1ea6d6fe61e3@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch to the _scoped() version introduced in commit 365130fd47
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240404-hwmon_device_for_each_child_node_scoped-v1-2-53997abde43c@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch to the _scoped() version introduced in commit 365130fd47
("device property: Introduce device_for_each_child_node_scoped()")
to remove the need for manual calling of fwnode_handle_put() in the
paths where the code exits the loop early.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240404-hwmon_device_for_each_child_node_scoped-v1-1-53997abde43c@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-32-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-31-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-30-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-29-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-28-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-27-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-26-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-25-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-24-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-23-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-22-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-21-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-20-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-19-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-18-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-17-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-16-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-15-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-14-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-13-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-12-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-11-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-10-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-9-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-8-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-7-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-6-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-5-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-4-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-3-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403203633.914389-2-afd@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use spi_get_device_match_data() helper to simplify a bit the driver.
Also kernel_ulong_t type is preferred for kernel code over uintptr_t
(needed for the cast).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240606142515.132504-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "resp.sensor_name" comes from cros_ec_cmd() and it hasn't necessarily
been NUL terminated. We had not intended to read past "sensor_name_size"
bytes, however, there is a width vs precision bug in the format string.
The format needs to be precision '%.*s' instead of width '%*s'.
Precision prevents an out of bounds read, but width is a no-op.
Fixes: bc3e452580 ("hwmon: add ChromeOS EC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/42331b70-bd3c-496c-8c79-3ec4faad40b8@moroto.mountain
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Add support for g761 PWM Fan Controller.
The g761 is a copy of the g763 with the only difference of supporting
and internal clock. The internal clock is used if no clocks property is
defined in device node and in such case the required bit is enabled and
clock handling is skipped.
The internal clock oscillator runs at 31KHz.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20240604164348.542-3-ansuelsmth@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several hardware monitoring chips optionally support Packet Error Checking
(PEC). For some chips, PEC support can be enabled simply by setting
I2C_CLIENT_PEC in the i2c client data structure. Others require chip
specific code to enable or disable PEC support.
Introduce hwmon_chip_pec and HWMON_C_PEC to simplify adding configurable
PEC support for hardware monitoring drivers. A driver can set HWMON_C_PEC
in its chip information data to indicate PEC support. If a chip requires
chip specific code to enable or disable PEC support, the driver only needs
to implement support for the hwmon_chip_pec attribute to its write
function.
Packet Error Checking is only supported for SMBus devices. HWMON_C_PEC
must therefore only be set by a driver if the parent device is an I2C
device. Attempts to set HWMON_C_PEC on any other device type is not
supported and rejected.
The code calls i2c_check_functionality() to check if PEC is supported
by the I2C/SMBus controller. This function is only available if CONFIG_I2C
is enabled and reachable. For this reason, the added code needs to depend
on reachability of CONFIG_I2C.
Cc: Radu Sabau <radu.sabau@analog.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
