About 70% of the chips with revision RT5390R initialize incorrectly, using
the auxiliary antenna instead of the main one. The net result is that
signal reception is very poor (no AP further than 1M).
This chipset differs from RT5390 and RT5390F by its support of hardware
antenna diversity. Therefore antenna selection should be done
differently, by disabling software features and previously selected
antenna.
This changeset does just that, and makes all RT5390R work properly.
This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
driver.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy rates are not validated while configuring
tx rateset using iw. So below cmd is accepted by nl80211.
sudo iw wlan2 set bitrates legacy-2.4 1 2 3
Validate legacy rates and return
error if any rate in the rateset is not valid.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_ave_rssi need to be declare as export for driver to use it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original patch defined the correction margin but did not apply it.
Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend debugfs entry for dfs_stats with DFS detection events
and shared pool statistics.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following bug: in tkip mode, qos-null ps on/off packets
are dropped due to incorrect packet length so that ath9k softap
can't handle powersave state transition of peer STA correctly.
Signed-off-by: Michael Liang <mliang@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert driver to use private version of dig_t instead of global version.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert driver to use the private dig_t instead of a global version.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert driver to use the private instead of global version.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert rtl8192c to use the dm_digtable struct in the common header file
instead of the global variable. Without this change, every instance of
rtl8192ce and rtl8192cu will be using the same global arrays.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the dig_t and ps_t structures to the private variables.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move struct definitions for dig_t and ps_t to the common header file.
This move is needed to convert these structures from a "per-driver" to a
"per-interface" basis.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not work properly and reduces throughput.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds locking of the detector's shared pulse and PRI sequence
pools to enable multi-wiphy operation on SMP systems.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without it, I get compile errors due to missing TASK_NORMAL,
TASK_UNINTERRUPTIBLE and schedule.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the RX path on USB devices is handled in process context we can
use GFP_KERNEL for RX buffer allocation. This should reduce the
likelihood of allocation failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're already using BBP for values > 128. Make that explicit and allow
debugfs access.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch supports Avastar 88W8797 chipset with USB interface.
The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.
Also clean up locking and clear possibly stale ht cap.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!
This has been tested with ath9k.
The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax
RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can be moved to iwl-dev.h since it is op_mode specific.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Having cmd[], meta[] and skbs[] as separate arrays
in the TX queue structure is cache inefficient as
we need the data for a given entry together.
To improve this, create an array with these three
members (allocate meta as part of that struct) so
we have the data we need together located together
improving cache footprint.
The downside is that we need to allocate a lot of
memory in one chunk, about 10KiB (on 64-bit) which
isn't very efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This allows not to notify the transport about aggregation stopped
while aggregation haven't been started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.
MVM doesn't have to use this declaration.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Please merge this with "iwlwifi: op_mode holds its pointer
to the config"
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Changed disable calibration bit field defines to enum.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Each modules will hold a pointer to struct device instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using the shared area that we be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using the shared area that we be killed.
Remove the pointer to config from shared since it is not
used any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using the shared area that will be killed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
