[Why]
When "max bpc" is set to enable deep color, some modes are removed from
the list if they fail validation on max bpc. These modes should be kept
if they validates fine with lower bpc.
[How]
- Retry with lower bpc in mode validation.
- Same in atomic commit to apply working bpc, not necessarily max bpc.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The minimum plane size we can support in DML is 16x16. If we try to pass
a 16x16 plane with dynamic pipe split then validation will fail since it
tries to split it into two pipes, each 8x8.
Some userspace doesn't check that the commit fails and because the
commit fails the old state is retained, resulting in corruption.
[How]
Add a workaround to avoid pipe split if any plane is 16x16 or smaller.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP training sequence to set SCRAMBLING_DISABLE bit properly based on
training pattern - per DP Spec.
[How]
Update dpcd_pattern.v1_4.SCRAMBLING_DISABLE with 1 for TPS1, TPS2, TPS3,
but not for TPS4.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current odm/mpc combine logic to detect which pipes need to split
logically is flawed leading to incorrect pipe merge/split operations
being taken.
This change cleans up the logic and fixes the logical errors.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Assigning a different DSC resource than the one previosly used is
currently not handled. This causes black screen on mode change when more
than one monitor is connected on some ASICs.
[how]
- Acquire the previously used DSC if available
- Make sure re-program is triggered if new DSC is used
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under xgmi setup,some sysfs fail to create for the second time of kmd
driver loading. It's due to sysfs nodes are not removed appropriately
in the last unlod time.
Changes of this patch:
1. remove sysfs for dev_attr_xgmi_error
2. remove sysfs_link adev->dev->kobj with target name.
And it only needs to be removed once for a xgmi setup
3. remove sysfs_link hive->kobj with target name
In amdgpu_xgmi_remove_device:
1. amdgpu_xgmi_sysfs_rem_dev_info needs to be run per device
2. amdgpu_xgmi_sysfs_destroy needs to be run on the last node of
device.
v2: initialize array with memset
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The prompts will contain pci address(segment/bus/port/function),
severity(warn or error) and some keywords(GPU, amdgpu). Also this
address the issue that pci bus retrieved by PCI_BUS_NUM(adev->pdev->devfn)
is wrong.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing on a Polaris11 gpu with DCE-11.2 suggests that it
seems to work fine there, so optimistically enable it for
DCE-11 and later.
v2: drop DCE 11.0 hunk. Carrizo (DCE 11.0) has a HW bug where FP16
scaling doesn't work. The upscale and downscale factors were
intended to block those FP16 cases and reject the commit but
nobody ever added those to atomic check. Once those are added
to atomic check, this can be re-enabled.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose support for DRM_FORMAT_ABGR16161616F and
DRM_FORMAT_XBGR16161616F to the DRM core, complementing
the already existing xRGB ordered fp16 formats.
These are especially useful for creating presentable
swapchains in Vulkan for VK_FORMAT_R16G16B16A16_SFLOAT.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SCRATCH2 is used to keep decode wptr as a workaround
which fix a hardware DPG decode wptr update bug for
vcn2.5 beforehand.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Return statements in functions returning bool should use
true/false instead of 1/0.
drivers/gpu/drm/amd/amdkfd/kfd_int_process_v9.c:40:9-10:
WARNING: return of 0/1 in function 'event_interrupt_isr_v9' with return type bool
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
One call was forcing stutter on instead of looking at the debug option.
Ensure we always check the debug option unless we want to force stutter
off.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
At bringup we want to be able to disable various power features.
[How]
These features are already exposed as dc_debug_options and exercised
on other OSes. Create a new dc_debug_mask module parameter and expose
relevant bits, in particular
* DC_DISABLE_PIPE_SPLIT
* DC_DISABLE_STUTTER
* DC_DISABLE_DSC
* DC_DISABLE_CLOCK_GATING
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the amdgpu device attribute node will be created accordding to sriov vf
mode at runtime.
cleanup unnecessary sriov check in attribute operation function.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to be valid to dereference during the i915_fence_release, after
retiring the fence and releasing its refererences, we assume that
rq->engine can only be a real engine (that stay intact until the device
is shutdown after all fences have been flushed). However, due to a quirk
of preempt-to-busy, we may retire a request that still belongs to a
virtual engine and so eventually free it with rq->engine being invalid.
To avoid dereferencing that invalid engine, we look at the
execution_mask which if it indicates it may be executed on more than one
engine, we know it originated on a virtual engine and may still be on
one.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1906
Fixes: 43acd6516c ("drm/i915: Keep a per-engine request pool")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200521140617.30015-2-chris@chris-wilson.co.uk
Since the removal of the no-semaphore boosting, we rely on timeslicing to
reorder passed inter-dependency hogs across the engines. However, we
require preemption to support timeslicing into user payloads, and not all
machine support preemption so we do not universally enable timeslicing,
even when it would correctly preempt our own inter-engine semaphores.
Since timeslicing and semaphore priority deboosting is now disabled on
Broadwell/Braswell, we have to follow suite and not use semaphores.
Testcase: igt/gem_exec_schedule/semaphore-codependency # bdw/bsw
Fixes: 18e4af04d2 ("drm/i915: Drop no-semaphore boosting")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200521140617.30015-1-chris@chris-wilson.co.uk
While working on commit b5372fe5dc ("exec: load_script: Do not exec
truncated interpreter path"), I wrote a series of test scripts to verify
corner cases. However, soon after, commit 6eb3c3d0a5 ("exec: increase
BINPRM_BUF_SIZE to 256") landed, resulting in the tests needing to be
refactored for the larger BINPRM_BUF_SIZE, which got lost on my TODO
list. During the recent exec refactoring work[1], the need for these tests
resurfaced, so I've finished them up for addition to the kernel selftests.
[1] https://lore.kernel.org/lkml/202005191144.E3112135@keescook/
Link: https://lkml.kernel.org/r/202005200204.D07DF079@keescook
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
It is hard to follow the control flow in exec.c as the code has evolved over
time and something that used to work one way now works another. This set of
changes attempts to address the worst of that, to remove unnecessary work
and to make the code a little easier to follow.
The churn is a bit higher than the last version of this patchset, with
renaming and cleaning up of comments. I have split security_bprm_set_creds
into security_bprm_creds_for_exec and security_bprm_repopulate_creds. My
goal was to make it clear that one hook completes its work while the other
recaculates it's work each time a new interpreter is selected.
I have added a new change at the beginning to make it clear that neither
security_bprm_creds_for_exec nor security_bprm_repopulate_creds needs to be
implemented as prepare_exec_creds properly does the work of setting up
credentials unless something special is going on.
I have made the execfd support generic and moved out of binfmt_misc so that
I can remove the recursion.
I have moved reassigning bprm->file into the loop that replaces the
recursion. In doing so I discovered that binfmt_misc was naughty and
was returning -ENOEXEC in such a way that the search_binary_handler loop
could not continue. So I added a change to remove that naughtiness.
Eric W. Biederman (8):
exec: Teach prepare_exec_creds how exec treats uids & gids
exec: Factor security_bprm_creds_for_exec out of security_bprm_set_creds
exec: Convert security_bprm_set_creds into security_bprm_repopulate_creds
exec: Allow load_misc_binary to call prepare_binfmt unconditionally
exec: Move the call of prepare_binprm into search_binary_handler
exec/binfmt_script: Don't modify bprm->buf and then return -ENOEXEC
exec: Generic execfd support
exec: Remove recursion from search_binary_handler
arch/alpha/kernel/binfmt_loader.c | 11 +----
fs/binfmt_elf.c | 4 +-
fs/binfmt_elf_fdpic.c | 4 +-
fs/binfmt_em86.c | 13 +----
fs/binfmt_misc.c | 69 ++++-----------------------
fs/binfmt_script.c | 82 ++++++++++++++------------------
fs/exec.c | 97 ++++++++++++++++++++++++++------------
include/linux/binfmts.h | 36 ++++++--------
include/linux/lsm_hook_defs.h | 3 +-
include/linux/lsm_hooks.h | 52 +++++++++++---------
include/linux/security.h | 14 ++++--
kernel/cred.c | 3 ++
security/apparmor/domain.c | 7 +--
security/apparmor/include/domain.h | 2 +-
security/apparmor/lsm.c | 2 +-
security/commoncap.c | 9 ++--
security/security.c | 9 +++-
security/selinux/hooks.c | 8 ++--
security/smack/smack_lsm.c | 9 ++--
security/tomoyo/tomoyo.c | 12 ++---
20 files changed, 202 insertions(+), 244 deletions(-)
Link: https://lkml.kernel.org/r/877dx822er.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Recursion in kernel code is generally a bad idea as it can overflow
the kernel stack. Recursion in exec also hides that the code is
looping and that the loop changes bprm->file.
Instead of recursing in search_binary_handler have the methods that
would recurse set bprm->interpreter and return 0. Modify exec_binprm
to loop when bprm->interpreter is set. Consolidate all of the
reassignments of bprm->file in that loop to make it clear what is
going on.
The structure of the new loop in exec_binprm is that all errors return
immediately, while successful completion (ret == 0 &&
!bprm->interpreter) just breaks out of the loop and runs what
exec_bprm has always run upon successful completion.
Fail if the an interpreter is being call after execfd has been set.
The code has never properly handled an interpreter being called with
execfd being set and with reassignments of bprm->file and the
assignment of bprm->executable in generic code it has finally become
possible to test and fail when if this problematic condition happens.
With the reassignments of bprm->file and the assignment of
bprm->executable moved into the generic code add a test to see if
bprm->executable is being reassigned.
In search_binary_handler remove the test for !bprm->file. With all
reassignments of bprm->file moved to exec_binprm bprm->file can never
be NULL in search_binary_handler.
Link: https://lkml.kernel.org/r/87sgfwyd84.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Most of the support for passing the file descriptor of an executable
to an interpreter already lives in the generic code and in binfmt_elf.
Rework the fields in binfmt_elf that deal with executable file
descriptor passing to make executable file descriptor passing a first
class concept.
Move the fd_install from binfmt_misc into begin_new_exec after the new
creds have been installed. This means that accessing the file through
/proc/<pid>/fd/N is able to see the creds for the new executable
before allowing access to the new executables files.
Performing the install of the executables file descriptor after
the point of no return also means that nothing special needs to
be done on error. The exiting of the process will close all
of it's open files.
Move the would_dump from binfmt_misc into begin_new_exec right
after would_dump is called on the bprm->file. This makes it
obvious this case exists and that no nesting of bprm->file is
currently supported.
In binfmt_misc the movement of fd_install into generic code means
that it's special error exit path is no longer needed.
Link: https://lkml.kernel.org/r/87y2poyd91.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The return code -ENOEXEC serves to tell search_binary_handler that it
should continue searching for the binfmt to handle a given file. This
makes return -ENOEXEC with a bprm->buf that is needed to continue the
search problematic.
The current binfmt_script manages to escape problems as it closes and
clears bprm->file before return -ENOEXEC with bprm->buf modified.
This prevents search_binary_handler from looping as it explicitly
handles a NULL bprm->file.
I plan on moving all of the bprm->file managment into fs/exec.c and out
of the binary handlers so this will become a problem.
Move closing bprm->file and the test for BINPRM_PATH_INACCESSIBLE
down below the last return of -ENOEXEC.
Introduce i_sep and i_end to track the end of the first argument and
the end of the parameters respectively. Using those, constification
of all char * pointers, and the helpers next_terminator and
next_non_spacetab guarantee the parameter parsing will not modify
bprm->buf.
Only modify bprm->buf to terminate the strings i_arg and i_name with
'\0' for passing to copy_strings_kernel.
When replacing loops with next_non_spacetab and next_terminator care
has been take that the logic of the parsing code (short of replacing
characters by '\0') remains the same.
Link: https://lkml.kernel.org/r/874ksczru6.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add a flag preserve_creds that binfmt_misc can set to prevent
credentials from being updated. This allows binfmt_misc to always
call prepare_binprm. Allowing the credential computation logic to be
consolidated.
Not replacing the credentials with the interpreters credentials is
safe because because an open file descriptor to the executable is
passed to the interpreter. As the interpreter does not need to
reopen the executable it is guaranteed to see the same file that
exec sees.
Ref: c407c033de84 ("[PATCH] binfmt_misc: improve calculation of interpreter's credentials")
Link: https://lkml.kernel.org/r/87imgszrwo.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Rename bprm->cap_elevated to bprm->active_secureexec and initialize it
in prepare_binprm instead of in cap_bprm_set_creds. Initializing
bprm->active_secureexec in prepare_binprm allows multiple
implementations of security_bprm_repopulate_creds to play nicely with
each other.
Rename security_bprm_set_creds to security_bprm_reopulate_creds to
emphasize that this path recomputes part of bprm->cred. This
recomputation avoids the time of check vs time of use problems that
are inherent in unix #! interpreters.
In short two renames and a move in the location of initializing
bprm->active_secureexec.
Link: https://lkml.kernel.org/r/87o8qkzrxp.fsf_-_@x220.int.ebiederm.org
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Highlights of this series:
* Remove serialization of sending RPC/RDMA Replies
* Convert the TCP socket send path to use xdr_buf::bvecs (pre-requisite for
RPC-on-TLS)
* Fix svcrdma backchannel sendto return code
* Convert a number of dprintk call sites to use tracepoints
* Fix the "suggest braces around empty body in an 'else' statement" warning
Zoned block device specification do not define the behavior of
discard/trim command as this command is generally replaced by the reset
write pointer (zone reset) command. Emulate this in null_blk by making
zoned and discard options mutually exclusive.
Suggested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch the bus clk use imx8m_clk_hw_composite_bus, then
we could avoid possible issue when setting mux of the clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx8m_clk_hw_composite_bus api for bus clk root slice usage.
Because the mux switch sequence issue, we could not reuse Peripheral
Clock Slice code, need use composite specific mux operation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
