u-boot/board/storopack/smegw01/smegw01.c
Fabio Estevam 40496ac3b7 mx7d: Add Storopack's SMEGW01 board
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.

Based on the original U-Boot work done by Phytec.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2021-06-09 13:34:38 +02:00

96 lines
2.0 KiB
C

// SPDX-License-Identifier: GPL-2.0+
// Copyright (C) 2021 Fabio Estevam <festevam@denx.de>
#include <init.h>
#include <net.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx7-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/mach-imx/hab.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/io.h>
#include <common.h>
#include <env.h>
#include <asm/arch/crm_regs.h>
#include <asm/setup.h>
#include <asm/bootm.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \
PAD_CTL_HYS)
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_SIZE;
return 0;
}
static iomux_v3_cfg_t const wdog_pads[] = {
MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const uart1_pads[] = {
MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
};
static int setup_fec(void)
{
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
int ret;
/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
ret = set_clk_enet(ENET_125MHZ);
if (ret)
return ret;
return 0;
}
int board_early_init_f(void)
{
setup_iomux_uart();
setup_fec();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
return 0;
}
int board_late_init(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
/*
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
* since we use PMIC_PWRON to reset the board.
*/
clrsetbits_le16(&wdog->wcr, 0, 0x10);
return 0;
}