This patch supports page programming using STIG write. This is needed
if controller support only STIG writes for page program instead of
regular indirect write support. So, this patch gets the controller
capability from dt using "cdns,is-stig-pgm" property. This patch also
modifies stig write routine to support for page programming.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for DMA read operation if controller
supports it which is determined by reading DT property "cdns,is-dma".
This patch provides hooks for vendor specific DMA routines as the
cadence qspi controller supports external DMA which is vendor specific.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for Micron OSPI flash device MT35Xl512.
This device supports Octal Read commands along with regular
SPI and Quad commands.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds octal read command support if flash
device and controller supports it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If instance number is passed to func(, , 0) then it has to be reflected
by bootcmd_<name><instance number> command.
Do it in a more generic way that devtypel and instance numbers are taken
from parameters.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This platform is going to become generic that's why it is necessary also
enable different PHY vendors.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new config option which is used for
reserving a specific memory for MMU Table and in this
case we are using TCM for that purpose.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update boot_targets based on bootmode to run corresponding
distroboot command first.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, nand and nor.
The distro boot commands now reads the script from flash offset
of 15.75MB and executes it.
Setup default location via script_offset_f to 15.75MB to match the most
xilinx reference boards for qspi, nand and set the same using
script_offset_nor to 0xE2EC0000 for nor.
256kB allocated space for script size (script_size_f) should be more
than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms are converted to DM_I2C that's why there is no reason to
keep this code here.
Note: Update also Makefile till zc706_eeprom is updated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these board have also eeprom enabled that's why it is also enabled
via defconfig.
There is also no need to have zc70x specific config file that's why also
remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All platforms have been converted to DM that's why there is no reason to
keep addresses in headers. They are all read from DT now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is much easier to point to eeprom which stores information like MAC
address directly via DT. eeprom which contains this information is
pointed by /chosen/xlnx,eeprom parameter.
For example:
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
+ xlnx,eeprom = &eeprom;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq and ZynqMP are sharing similar code and there is no reason to do
code duplication. Move zynq_board_read_rom_ethaddr() to common file for
easier conversion to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linux kernel binding is using atmel,24c08 compatible string. On the
other hand there is atmel,24c08a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
These eeproms are available on several ZynqMP development boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no i2c connected in base DT that's why disable I2C commands.
Also remove zynq_zybo which is not needed now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is checking the highest alias ID for eth, gpio, pci, i2c and error
code on non existing alias.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Find out the highest alias ID used for certain subsystem.
This call will be used for alocating IDs for i2c buses which are not
described in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the memory is being consumed by device binding code,
more space needed for other data structures.
Z-turn board has already hit the limit, others may follow soon.
Measuring only the memory consumed in device_bind_common, I've got
the following results (in decimal):
root_driver: 108
mod_exp_sw: 108
amba: 120
serial@e0000000 aka uart0: 112
serial@e0001000 aka uart1: 88
spi@e000d000 aka qspi: 120
sdhci@e0100000 aka mmc0: 455
sdhci@e0100000.blk: 208
slcr@f8000000: 96
clkc@100: 72
(total) 1487 = 0x5cf of 0x600
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus can use GEM0 through MIO pins, which requires a 125 MHz TX
clock to be generated. With the IO PLL at 1200 MHz this isn't possible, so
change it to run at 1000 and adjust the divisors accordingly. Also set the
GEM0 clock source to MIO instead of EMIO.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update cadence i2c driver to support livetree
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This change enables setting up specific Qemu version or sha1 for new
targets which are added after (current) v3.0.0 version.
This changes is preparation step for adding new Xilinx Versal Virt
platform which was merge after v3.0.0.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When FPGA programming fails, it does so silently, unless debugging
code is enabled. This makes it hard to detect problems in production
environments.
Print the error message unconditionally so the error doesn't go
unnoticed.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updates i2c muxes drivers to support livetree.
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi and nand. The
distro boot commands now reads the script from flash offset
of 63.5MB and executes it.
Setup default location via script_offset_f to 63.5MB to match the most
xilinx reference boards. 512kB allocated space for script size
(script_size_f) should be more than enough to cover custom boot logic.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
