Commit Graph

73877 Commits

Author SHA1 Message Date
Breno Lima
edf95bdedd mx7ulp: wdog: Wait for WDOG unlock and reconfiguration to complete
According to i.MX7ULP Reference Manual we should wait for WDOG unlock
and reconfiguration to complete.

Section "59.5.3 Configure Watchdog" provides the following example:

DisableInterrupts; //disable global interrupt
WDOG_CNT = 0xD928C520; //unlock watchdog
while(WDOG_CS[ULK]==0); //wait until registers are unlocked
WDOG_TOVAL = 256; //set timeout value
WDOG_CS = WDOG_CS_EN(1) | WDOG_CS_CLK(1) | WDOG_CS_INT(1) |
	  WDOG_CS_WIN(0) | WDOG_CS_UPDATE(1);
while(WDOG_CS[RCS]==0); //wait until new configuration takes effect
EnableInterrupts; //enable global interrupt

Update U-Boot WDOG driver to align with i.MX7ULP reference manual.

Use 32 bits accessing to CS register. According to RM, the bits in
this register only can write once after unlock. So using 8 bits access
will cause problem.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-07-17 14:59:56 +02:00
Breno Lima
c6ae713c7c mx7ulp: Update unlock and refresh sequences in sWDOG driver
According to i.MX7ULP Reference Manual the second word write for both
UNLOCK and REFRESH operations must occur in maximum 16 bus clock.

The current code is using writel() function which has a DMB barrier to
order the memory access. The DMB between two words write may introduce
some delay in certain circumstance, causing a WDOG timeout due to 16 bus
clock window requirement.

Replace writel() function by __raw_writel() to achieve a faster memory
access and avoid such issue.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
2021-07-17 14:59:56 +02:00
Ye Li
cb391e3399 imx8mq_evk: Enable the USB3.0 host port
Setup USB clock in board codes, and enable the DWC3 XHCI and
PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
2021-07-17 13:12:23 +02:00
Ye Li
4a837d433c arm: imx8mq: Add USB clock init function
Add clock function to setup relevant clocks for USB3.0 controllers and
PHYs on i.MX8MQ

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
2021-07-17 13:12:23 +02:00
Ye Li
4390e9f997 arm: dts: imx8mq: Add alias for two usb controllers
Add alias for two DWC3 usb controllers to fix the seq index.

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Patrick Wildt <patrick@blueri.se>
2021-07-17 13:12:23 +02:00
Ye Li
4266dc1dff phy: phy-imx8mq-usb: Add USB PHY driver for i.MX8MQ
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
2021-07-17 13:12:23 +02:00
Stefano Babic
375d7e9298 spi: mxc_spi: fix warnings if CLK_ENABLED not set
Following warnings (unused variables) are raised:

drivers/spi/mxc_spi.c: In function 'mxc_spi_probe':
drivers/spi/mxc_spi.c:595:14: error: unused variable 'blob' [-Werror=unused-variable]
595 |  const void *blob = gd->fdt_blob;
    |              ^~~~
drivers/spi/mxc_spi.c:594:6: error: unused variable 'node' [-Werror=unused-variable]
594 |  int node = dev_of_offset(bus);

Move the variable declaration inside the code where they are used.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2021-07-10 18:14:54 +02:00
Cody Gray
55d46761a3 mx6sabresd: Make checkboard respect CONFIG_NXP_BOARD_REVISION
The default implementation of checkboard() calls the
nxp_board_rev_string() function
to retrieve a character representing the revision number of the board.
However, this
attempt to retrieve the revision number may fail in certain situations or be
otherwise undesirable.

There is already a configuration option to avoid retrieving the
revision number of
the board: CONFIG_NXP_BOARD_REVISION. In fact, if this option is enabled, the
nxp_board_rev_string() function's definition will be omitted entirely,
meaning that the previous implementation of checkboard() would result
in a linker error.

This changeset makes the default implementation of checkboard() respect the
CONFIG_NXP_BOARD_REVISION configuration option, only attempting to retrieve
the board revision number if that option is defined.

Signed-off-by: Cody Gray <cody@codygray.com>
2021-07-10 18:14:25 +02:00
Marek Vasut
a5ee05cf71 ARM: imx: Pick correct eMMC boot partition from ROM log
In case the iMX8M boot from eMMC boot partition and the primary image
is corrupted, the BootROM is capable of starting a secondary image in
the other eMMC boot partition as a fallback.

However, the BootROM leaves the eMMC BOOT_PARTITION_ENABLE setting as
it was, i.e. pointing to the boot partition containing the corrupted
image, and the BootROM does not provide any indication that this sort
of fallback occured.

According to AN12853 i.MX ROMs Log Events, Rev. 0, May 2020, it is
possible to determine whether fallback event occurred by parsing the
ROM event log. In case ROM event ID 0x51 is present, fallback event
did occur.

This patch implements ROM event log parsing and search for event ID
0x51 for all iMX8M SoCs, and based on that corrects the eMMC boot
partition selection. This way, the SPL loads the remaining boot
components from the same eMMC boot partition from which it was
started, even in case of the fallback.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
2021-07-10 18:12:42 +02:00
Marek Vasut
9b19159174 spl: mmc: Factor out eMMC boot partition selection code
Factor out eMMC boot partition selection code into
default_spl_mmc_emmc_boot_partition() function and implement
weak spl_mmc_emmc_boot_partition(), so that architecture or
board code can override the eMMC boot partition selection.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
d107235a38 board: gateworks: venice: remove forced enable of GSC thermal protection
The Gateworks System Controller thermal protection feature will disable
the board primary power supply if the on-board temperature sensor
reaches 86C. In many cases this could occur before the temperature
critical components such as CPU, DRAM, eMMC, and power supplies have
reached their max temperature.

Remove the forced re-enable of thermal protection so that users can
knowingly disable it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
0f3f6e62ea board: gateworks: venice: add ftd_file env vars on boot
The ftd_file* vars can be used by bootscripts to look for
appropriate dtb's

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
9d2e639f8e board: gateworks: venice: display DTB used
Display the DTB file used for U-Boot.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
658eb1abd8 board: gateworks: venice: gsc: fix voltage offset
The voltage offset property is in microvolts so must be scaled
accordingly.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
c4e5656620 board: gateworks: venice: gsc: fix typo
Fix typo in error message.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
9fe2106fe0 configs: imx8mm_venice_defconfig: add support for gbe switch
The imx8mm-venice-gw7901 board has an I2C connected KSZ9897S GbE switch
with an IMX8MM FEC MAC master connected via RGMII_ID.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
1cb87b929e arm: dts: imx8mm-venice-gw7901.dts: fix dsa switch configuration
Fix the dsa switch config:
- remove the unnecessary phy-mode from the switch itself
- added the necessary fixed-link node to the non-cpu ports required
  for U-Boot DSA

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
668e205098 net: add support for KSZ9477/KSZ9897/KSZ9567 GbE switch
The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches
support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO.

This driver currently supports I2C register access but SPI or MDIO register
access can be easily added at a later time.

Tagging is not implemented and instead the active port is tracked to
avoid needing a tag to store port information.

This was tested with the imx8mm-venice-gw7901 board which has a
KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:42 +02:00
Tim Harvey
431f9d72ff net: dsa: enable master promisc mode if available and needed
If ports have their own unique MAC addrs and master has a set_promisc
function, call it so that packets will be received for ports.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:41 +02:00
Tim Harvey
87550a814e net: fec: add set_promisc function
Enabling promiscuous mode is necessary if FEC is the master of a DSA
switch driver where each port has their own MAC address.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:41 +02:00
Tim Harvey
631f3afbef net: add set_promisc function to enable/disable Promiscuous mode
Enabling promiscuous mode can be useful for DSA switches where each port
has its own MAC address.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:41 +02:00
Tim Harvey
69c81d6546 net: fec: set phy_of_node properly for fixed-link phy
If the FEC is connected to a fixed-link (upstream switch port for
example) the phy_of_node should be set to the fixed-link node
so that speed and other properties can be found properly.

In addition fix a typo in the debug string.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:41 +02:00
Tim Harvey
b247fa7b17 net: fec: use device sequence vs index when fetching fec
When using uclass_get_device* to get the FEC device we need to use
device sequence instead of index into UCLASS_ETH. In systems where for
example a I2C based DSA switch exists it will probe before the FEC
master and its ports will be registered first and have the first
indexes yet the FEC's sequence comes from the device-tree alias.

Take for example the imx8mm-venice-gw7901 board which has an i2c based
DSA switch:

u-boot=> net list
eth1 : lan1 00:0d:8d:aa:00:2f
eth2 : lan2 00:0d:8d:aa:00:30
eth3 : lan3 00:0d:8d:aa:00:31
eth4 : lan4 00:0d:8d:aa:00:32
eth0 : ethernet@30be0000 00:0d:8d:aa:00:2e active

Thus in this case uclass_get_device(UCLASS_ETH, 0, &dev) returns lan1
which is wrong but uclass_get_device_seq(UCLASS_ETH, 0, &dev) returns
ethernet@30be000 which is correct.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:41 +02:00
Tim Harvey
c9f7ef37f9 board: gateworks: venice: add imx8mm-gw7901 support
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
 - i.MX8M Mini SoC
 - LPDDR4 DRAM
 - eMMC FLASH
 - SPI FRAM
 - Gateworks System Controller (GSC)
 - Atmel ATECC Crypto Authentication
 - USB 2.0
 - Microchip GbE Switch
 - Multiple multi-protocol RS232/RS485/RS422 Serial ports
 - onboard 802.11ac WiFi / BT
 - microSD socket
 - miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
 - Wide range DC power input
 - 802.3at PoE

To add support for this board:
 - add dts from Linux (accepted for v5.14)
 - add SPL PMIC config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 18:12:41 +02:00
Frieder Schrempf
6b86554865 spi: fsl_qspi: Build driver only if DM_SPI is available
The driver depends on DM_SPI and if it's not available (e. g. in SPL),
then we should not try to build it as this will fail.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-07-10 16:53:34 +02:00
Kacper Kubkowski
a5dc91febd arm/mach-imx: Fix macros in mmdc_size.c
Make macros actually use passed parameter instead of local variables
that happen
to be named the same as symbols in macro expansion.

Signed-off-by: Kacper Kubkowski <kkubkowski@fluence.pl>
2021-07-10 16:53:34 +02:00
Teresa Remmet
bbf04b28d2 board: phytec: imx8mp-phycore: Switch to binman
Use now binman for image creation.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
f11e3dafb3 arm: dts: imx8mp-phyboard-pollux-rdk-u-boot: Add wdog pinctrl entry
Add missing pinctrl entry in spl.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
fd82763cd2 board: phytec: phycore-imx8mp: Enable DVS1 control
Enable DVS1 control through PMIC_STBY_REQ.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
0f166b85ac board: phytec: phycore_imx8mp: Set VDD_ARM to 0,95V
Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-07-10 16:53:34 +02:00
Teresa Remmet
60f64bec41 board: phytec: phycore_imx8mp: Add fec support
Enable support for the fec ethernet on phyCORE-i.MX8MP.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
1feac813fe board: phytec: phycore_imx8mp: Change debug UART
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
3240d9c63a arm: dts: imx8mp-phyboard-pollux: Sync dts files with kernel
This update includes eqos support and some minor changes.

Synced with kernel commit
412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
dafb164f61 arm: dts: imx8mp: Add common u-boot dtsi
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Teresa Remmet
6bd1db0a0c arm: dts: imx8mp: Resync imx8mp device tree include
Sync imx8mp include with kernel commit:
d1689cd3c0f4 ("arm64: dts: imx8mp: Use the correct name for child node "snps, dwc3"")

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-10 16:53:34 +02:00
Tim Harvey
c1f6fd2bb7 pci: imx: use reset-gpios if defined by device-tree
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.

Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
 - mx6sabresd
 - mx6sxsabresd
 - novena
 - tbs2910
 - vining_2000

Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.

Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:34 +02:00
Fabio Estevam
96f747b1f0 smegw01: Select the CMD_UNZIP option
Select the CMD_UNZIP option so that the 'gzwrite' command
can be used to flash .gz image into the eMMC.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2021-07-10 16:53:34 +02:00
Fabio Estevam
364212ca29 smegw01: Allow booting the Yocto image by default
On the Yocto image there is a single partition and the kernel
and dtb are present in the 'boot' directory.

Change it accordingly so that the board can boot the Yocto
image by default.

Use the generic 'load' command instead, which is able to
read from an ext4 partition.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2021-07-10 16:53:34 +02:00
Tim Harvey
31273c5af5 imx: ventana: display 'none' for MMC if board does not have it
print 'None' instead of just a blank line if nothing is detected:
MMC:  None

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:34 +02:00
Tim Harvey
b57b14dc70 imx: ventana: add support for DLC0700XDP21LF LCD display
Add LVDS support for DLC0700XDP21LF 7in 1024x600 display
(equivalent to the DLC-700JMGT4 with new touch controller)

Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
e9284c03bc imx: ventana: display neteowrk PHY
Add displaying the detected network PHY on boot.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
9634c748b1 imx: ventana: add DP83867 PHY LED configuration
Add DP83867 PHY LED configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
0545b17b69 imx: ventana: put LTC3676 regulators in continuous mode
In the default pulse-skipping mode regulators that are very lightly
loaded can fail to regulate properly. Switching them to always use
continuous mode causes only around 10mW of overall system power
difference in a lightly loaded system that isn't already operating
them in continuous mode.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
722d22813e imx: ventana: put PFUZ100 regulators in continuous mode
In the default 'auto' mode regulators that are very lightly loaded
can be put in PFM mode and fail to regulator properly. Switching them
to always use continuous PWM mode has a neglibable affect on system
power and garuntees proper regulation under lightly loaded circumstances.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
a32be88da0 imx: ventana: add PMIC fix for GW54xx-G
Substitutions in EOL parts changes the VDD_2P5 voltage rail such that
the previously unused VGEN6 LDO is needed in place of the lower power
VGEN5 for the GW54xx-G.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
6a4c67859c imx: ventana: add legacy uboot image support
Add Legacy U-Boot image support needed to boot a uImage.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
32328065b5 imx: ventana: increase SYS_BOOTM_LEN
Increase SYS_BOOM_LEN from the default 16M in imx6_common to 64M.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
729fd990c9 imx: ventana: remove unneeded includes
remove unnecessary includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Tim Harvey
ca942ca1d8 imx: ventana: remove USB_KEYBOARD support
For some time now having USB_KEYBOARD support has caused usb to be
initialized on boot. To allow for a quicker bootup we don't want this
for Ventana and don't really need USB keyboard support so remove it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-07-10 16:53:33 +02:00
Frieder Schrempf
e27bddff4b imx8m: Restrict usable memory to space below 4G boundary
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.

We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-07-10 16:03:01 +02:00