Intel Crown Bay board has one ethernet port connected from Intel
Topcliff PCH. Enable it in the board configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some ethernet drivers use their own version of ethernet FCS length
macro which is really common. We define ETH_FCS_LEN in net.h and
replace those custom versions in various places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Intel Quark SoC integrates two 10/100 ethernet controllers which can
be connected to an external RMII PHY. The MAC IP is from Designware.
Enable this support with the existing U-Boot Designware MAC driver
so that the ethernet port on Intel Galileo board can be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the description that how the compatible property is involved in
the fdtdec_get_pci_bdf() documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
To remove the ifdef conditional of CONFIG_SKIP_LOWLEVEL_INIT,
add late_lowlevel_init.S to U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no good reason to have the 0x1000 gap between
CONFIG_SYS_INIT_SP_ADDR and CONFIG_SYS_TEXT_BASE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM of UniPhier platform only loads 64KB image. We should
always make sure that SPL memory footprint is less than that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ifdef conditionals for CONFIG options are not Kconfig-friendly.
Instead, define CONFIG_SPL_STACK to prepare for Kconfig moves.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable CONFIG_SPL_DM and CONFIG_SPL_SERIAL_SUPPORT, which provide
Driver Model UART support on SPL.
CONFIG_SYS_SPL_MALLOC_{START,SIZE} should be dropped because simple
malloc is preferred on SPL. Dlmalloc requires some static variables
on .data section that is not available yet for NOR boot mode etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As the u-boot-spl.lds is used only for armv7 SoCs (includes
sama5d3 and sama5d4), so move it to armv7 directory.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As the u-boot-spl.lds is moved to <arch/arm/mach-at91> directory.
So, correct the path for sama5d4 related boards.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This patch enable the MCI support for at91sam9rlek board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase on ToT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Update the nand flash offset mapping, default nand bootcmand and
bootargs to align with linux4sam.org.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Larry Johnson <lrj@acm.org>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Erik Theisen <etheisen@mindspring.com>
They have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We don't want that CONSOLE is redirected to LCD upon init, we rather prefer
that console is still on the serial line.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This should make it more clear why there appear to be C pre-processor
symbols in the file that contain mixed case. They're really error
messages.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Beagle X15 is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.
The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.
Increase the auto-negotiation time-out for Beagle-X15 to handle
this case.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is in preperation of using generic cross OMAP code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The purpose of this build target is to do SPL over USB RNDIS. We remove
YMODEM, MMC and NAND (and re-set ENV to be built-in) as when those are needed
we can use the other build targets. This brings us well under size limit again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit ad8aae82b2 ("mx6sabre: Enable User Mass Storage") SPL target
does not boot anymore due to the increased spl image size.
Only enable USB Mass Storage for the non-SPL target.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Warp has a DDR eMMC, so enable CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE for better
performance:
reading zImage
5790288 bytes read in 117 ms (47.2 MiB/s)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE should be selected only by boards that really
have a DDR-capable eMMC, so remove this option from common code to avoid
regressions.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Tested-by: Stefan Roese <sr@denx.de>
By not defining CONFIG_SYS_PROMPT, the standard "=>" prompt is used, so remove
its definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Replace "mmc open/close" with "mmc dev" in mx6sabre_common.h as those commands
were removed with this commit: 614b2bf1c9
cmd_mmc.c: Drop open/close mmc sub-commands
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Device Firmware Upgrade (DFU) is a very convenient mechanism to upgrade U-boot
on the eMMC.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be
enabled on all sunxi boards. Also fix a compile error which shows up once
VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some of the AXP PMICs support VBUS detection, i.e. checking whether
VBUS power input is available and usable (supplied by an external
source). A few boards use this instead of a separate GPIO to detect
VBUS on USB OTG.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.
The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.
Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.
This makes the Juno platform start U-Boot properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Tom Warren <twarren.nvidia@gmail.com>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This commit enables the following configs:
- CONFIG_USE_ARCH_MEMCPY
- CONFIG_USE_ARCH_MEMSET
This increases the performance of memcpy/memset
and also reduces the boot time.
This was tested on Trats2.
A quick test with trace. Boot time from start to main_loop() entry:
- ~1527ms - before this change (arch memset enabled for .bss clear)
- ~1384ms - after this change
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
With limit of 16 symbols very simple device names derived drom device
tree description could not be displayed correctly.
For example "serial0@0xc0fc1000" will be truncated to sensless
"serial0@0xc0fc10" - note dropped tariling zeros.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For some assemblers, they use another character as newline in a macro
(e.g. arc uses '`'), so for generic assembly code, need use ASM_NL (a
macro) instead of ';' for it.
Basically this is the same patch as applied to Linux kernel -
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/include/linux/linkage.h?id=9df62f054406992ce41ec4558fca6a0fa56fffeb
but modified a bit to fit in U-Boot.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
This configures the Juno board to enable ethernet using the
SMSC9118 ethernet controller found in the board. Tested by
TFTP-booting a kernel over ethernet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds generic board support for MCF547X/8X and MCF5445X.
It is based on the patch about common generic board support for
M68K architecture sent by Angelo.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
For series testing purpose we need to boot some linux, therefore we enable
the needed features
- bootz
- devicetree
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The board has been redesigned, therefore we need from now other I/O Pins to
mux and handle.
Older boards aren't supported from now anymore.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Due to several changes of the boot-process we've redesigned the default-
environment settings completly.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Customer wants to display some logo very quickly after power on, so we support
from now loading a compressed bmp.gz to the screen.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
time measurement of u-boot commands is needed very often during development.
We add this feature until development is completed. Maybe forever :)
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
It is often necessary to "break in" into boards bootloader commandline if
something fails or even for development purposes some parameters have to be
changed.
So we enable u-boot's CONFIG_NETCONSOLE feature.
We also modify Networksettings to apply with this new use-case.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Without this change the board support for these SPEAr boards would
be dropped soon. Generic board support seems to work just fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Saves having to remember to ask make for it explicitly.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Built and booted to a Linux prompt with no issues discovered. network and usb
access to the external mmc are ok. (my internal mmc is knackered at the h/w
level).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
1. esbc_validate command is meant for validating header and
signature of images (Boot Script and ESBC uboot client).
SHA-256 and RSA operations are performed using SEC block in HW.
This command works on both PBL based and Non PBL based Freescale
platforms.
Command usage:
esbc_validate img_hdr_addr [pub_key_hash]
2. ESBC uboot client can be linux. Additionally, rootfs and device
tree blob can also be signed.
3. In the event of header or signature failure in validation,
ITS and ITF bits determine further course of action.
4. In case of soft failure, appropriate error is dumped on console.
5. In case of hard failure, SoC is issued RESET REQUEST after
dumping error on the console.
6. KEY REVOCATION Feature:
QorIQ platforms like B4/T4 have support of srk key table and key
revocation in ISBC code in Silicon.
The srk key table allows the user to have a key table with multiple
keys and revoke any key in case of particular key gets compromised.
In case the ISBC code uses the key revocation and srk key table to
verify the u-boot code, the subsequent chain of trust should also
use the same.
6. ISBC KEY EXTENSION Feature:
This feature allows large number of keys to be used for esbc validation
of images. A set of public keys is being signed and validated by ISBC
which can be further used for esbc validation of images.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Security Monitor is the SOC’s central reporting point for
security-relevant events such as the success or failure of boot
software validation and the detection of potential security compromises.
The API's for transition of Security states have been added
which will be used in case of SECURE BOOT.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale sfp has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
sfp_regs to common include. This patch also defines ccsr_sfp_regs
definition for newer versions of SFP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
