The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit 83cfbeb0df ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The helper is used to reset PHYs on connect and it determines the clause
to use (C22/C45) based on interface type. This fixes 'PHY reset timed out'
warnings in console for USXGMII/XFI PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 27c3f70f3b ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: net: phy: Increase link up delay in genphy_update_link() ("27c3f70f3b50")
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
doc/README.drivers.eth seems like a good source for understanding
U-Boot's network subsystem, but is only talking about legacy network
drivers. This is particularly sad as proper documentation would help in
porting drivers over to the driver model.
Rewrite the document to describe network drivers in the new driver model
world. Most driver callbacks/methods are almost identical in their
semantic, but recv() differs in some important details.
Also keep some parts of the original text at the end, to help
understanding old drivers. Add some hints on how to port drivers over.
This also uses the opportunity to reformat the document in reST, on the
way moving it into doc/driver-model and adding it into the structure
there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We keep both of these jobs in sync as much as possible even when the
primary motivation is to keep Travis from exceeding the build time limit
there. With that in mind:
- Use "rk" not "rockchip" to get all Rockchip SoC platforms in one job,
rather than just all Rockchip vendor platforms.
- The NXP LX216* SoCs have their own job, exclude them from the AArch64
generic job.
- SoCFPGA SoCs have their own job, exclude them from the AArch64 generic
job.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow the default environment file to contain long lines split into
multiples lines.
Leading white spaces can be added for readability as well.
Signed-off-by: Samuel Mescoff <samuel@mescoff.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Revert "x86: use invd instead of wbinvd in real mode start code"
- Convert toradex boards README to reST
- serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()
- x86: apl: Use cpu_x86_get_count() for cpu_ops.get_count
Use cpu_x86_get_count() to read the number of cores.
cpu_x86_get_count() reads the number of CPUs from the device tree.
Using this function we can support multiple Apollo Lake
variants, e.g.: E3940 (4 cores) and E3930 (2 cores).
This was tested on the E3940 and E3930 Apollo Lake variants.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function cpu_x86_get_count() is also useful for other modules.
Make it non-static and add a prototype + description.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The value for "Top of CAR region" should be fefc0000, not
fefc000. This matches the Kconfig default values, as
SYS_CAR_ADDR and SYS_CAR_SIZE are 0xfef00000 and 0xc0000
respectively.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop the Apollo Lake prefix 'apl' from the functions, types and
variables in the P2SB driver.
The P2SB is not Apollo Lake specific, and as such it was moved in
commit 2999846c11 ("x86: Move P2SB from Apollo Lake to a more generic
location") from the Apollo Lake folder to the intel_common folder.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit 82de42fa14 ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit 3db886a5bf
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit 33c215af4b ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes: 82de42fa14 ("dm: core: Allocate parent data separate from probing parent")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # Tested on Intel Galileo
This reverts commit 0d67fac29f.
As real hardware testing (*) shows the above mentioned commit
breaks U-Boot on it. Revert for the upcoming release. We may get
more information in the future and optimize the code accordingly.
(*) on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix a typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If all branches of a switch statement have a return instruction, all
subsequent lines are unreachable.
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- add initial index for toradex boards reST documentation
- add initial colibri_imx7.rst doc file which provides all needed
information for obtaining a workable image ready for flashing
for both eMMC/NAND versions of Colibri iMX7.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: make title underline the same length as the title itself]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This function doesn't use uclass_find_first_device() correctly. Add a
check that the device is found so we don't try to read properties from a
NULL device.
The fixes booting on minnoxmax.
Fixes: 87f1084a63 ("x86: Adjust mrccache_get_region() to use livetree")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add driver flag to skip power domain disabling on device removal.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Denali SPL shim won't build without these options set,
set them accordingly to fix the build error and let the SPL
shim to work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The default timer rate may be different than 25 MHz, permit overriding
the default rate in board configuration file. Ultimatelly, this should
be properly handled by a clock driver, however that is not available
on Gen5 yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This adds a compatible string for m41st87. This ensures that this driver
can be used for m41st87.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
After the commit 9b643e312d ("treewide: replace with error()
with pr_err()"), there are pr_err() usages without line break. Add
missing line breaks for pr_err() used in f_thor.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
In case dfu command is being executed with timeout option,
the timer may expire in the middle of DFU operation. If there
is DFU request coming, we may simple reset timeout value
to prevent aborting of ongoing DFU operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
The HF/QSPI flash layout permits up to 1 MiB large bootloader blob,
set CONFIG_BOARD_SIZE_LIMIT to enforce this limit and set the
monitor size to match accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull request for UEFI sub-system for efi-2020-04-rc4 (2)
In Linux next-20200228 patches have been merged to load an initial ramdisk
using an EFI_LOAD_FILE2_PROTOCOL provided by the firmware. See commit
ec93fc371f01 ("efi/libstub: Add support for loading the initrd from a
device path"). The idea behind it is that the firmware should be
responsible for validating the initrd in a secure boot setup.
This pull-request comprises a patch series which let's U-Boot provide an
initial implementation of the EFI_LOAD_FILE2_PROTOCOL providing the initrd.
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
The compatible string "i2c-eeprom" is U-Boot own compatible, which
has never been approved by the DT community. "u-boot,i2c-offset-len"
is also a U-Boot own hack.
Linux adds "atmel,*" as generic compatibles, and U-Boot also followed
it by commit d7e28918aa ("i2c_eeprom: Add reading support").
The U-Boot own hack is no longer needed. Just sync with Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
