Restore global pointer before board_init_f_init_reserve call,
as "a0" can be set in harts_early_init call and we end up with
invalid global pointer.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Replace code that accessed the GPIO registers directly with code that
makes use of the LED_GPIO driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-38x-controlcenterdc-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-xp-theadorable-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Replace it by including of mvebu-u-boot.dtsi file. When board does not use
-u-boot.dtsi then mvebu-u-boot.dtsi is included automatically by makefile
scripts/Makefile.lib.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Set u-boot,dm-pre-reloc for /soc/, /soc/internal-regs/ and &uart0 nodes as
it is required on every 32-bit Armada SoCs. And set also u-boot,dm-pre-reloc
for &spi0 when going to boot from SPI because otherwise SPL SPI drivers do
not load.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
64-bit Armada DTS files are not build correctly during compilation of
32-bit Armada boards and vice versa. So fix makefile build system to
compile only those dts files which are compatible for the current build
(64-bit Armada DTS files only for 64-bit builds and 32-bit Armada DTS files
only for 32-bit builds).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
BootROM boot method should always work so always add it as fallback method
to spl_boot_list. In case U-Boot SPI driver fails it is better to try using
BootROM than hanging as by default only one boot method is specified.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UniPhier LD20, PXs2 and PXs3 boards have ethernet phy that has RX/TX delays
of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
So should set the phy-mode to "rgmii-id" to show that RX/TX delays are
enabled.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All `sm efuseread/efusewrite` commands exit with an error, even if the fuse
have actually been dealt with correctly.
This is because the smc call return the size it actually processed but this
result is checked against 0.
Return failure in do_efuse_read/write if the return value of
meson_sm_read/write_efuse() is not the requested size.
Fixes: 52195ba5f5 ("ARM: amlogic: add sm efuse write support and cmd for read/write efuse")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220804144138.33809-1-jbrunet@baylibre.com
This converts the following to Kconfig:
CONFIG_SYS_FSL_CORES_PER_CLUSTER
As part of this, correct the dependencies on SYS_FSL_THREADS_PER_CORE.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_CCSR_GUR_BE
CONFIG_SYS_FSL_CCSR_SCFG_BE
CONFIG_SYS_FSL_ESDHC_BE
CONFIG_SYS_FSL_IFC_BE
CONFIG_SYS_FSL_PEX_LUT_BE
CONFIG_SYS_FSL_CCSR_GUR_LE
CONFIG_SYS_FSL_CCSR_SCFG_LE
CONFIG_SYS_FSL_ESDHC_LE
CONFIG_SYS_FSL_IFC_LE
CONFIG_SYS_FSL_PEX_LUT_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
If the device is a GP and we detect a signing certificate then remove it.
It would fail to authenticate otherwise as the device is GP and has no
secure authentication services in SYSFW.
This shouldn't happen often as trying to boot signed images on GP devices
doesn't make much sense, but if we run into a signed image we should at
least try to ignore the certificate and boot the image anyway. This could
help with users of GP devices who only have HS images available.
If this does happen, print a nice big warning.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can skip the image authentication check at runtime if the device is GP.
This reduces the delta between GP and HS U-Boot builds. End goal is
to re-unify the two build types into one build that can run on all
device types.
Signed-off-by: Andrew Davis <afd@ti.com>
On HS-FS devices signing boot images is optional. To ease use
we check if we are HS-FS and if no certificate is attached
to the image we skip the authentication step with a warning
that this will fail when the device is set to security enforcing.
Signed-off-by: Andrew Davis <afd@ti.com>
K3 SoCs are available in a number of device types such as
GP, HS-FS, EMU, etc. Like OMAP SoCs we can detect this at runtime
and should print this out as part of the SoC information line.
We add this as part of the common.c file as it will be used
to also modify our security state early in the device boot.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL_GPIO_SUPPORT is named SPL_GPIO since commit 83061dbd1c ("Rename
GPIO_SUPPORT to GPIO"), SPL_MMC_SUPPORT is named SPL_MMC since commit
103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"), SPL_SERIAL_SUPPORT is
named SPL_SERIAL since commit 2a73606668 ("serial: Rename
SERIAL_SUPPORT to SERIAL") so let's select the correct Kconfig options.
Fixes: 8b71576f38 ("mx7ulp_com: add support for SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Signed-off-by: Marek Behún <kabel@kernel.org>
* Add SPDX-License-Identifier
* Add SFP and LED nodes
* Fix PHY nad NOR nodes
* Remove duplicates from u-boot.dtsi file
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
QorIQ U-Boot binary for SD card booting compiled during build process
(either u-boot.bin or u-boot-with-spl.bin) cannot be directly loaded by
QorIQ pre-PBL BootROM. Compiled U-Boot binary first needs to be processed
by Freescale boot_format tool as described in doc/README.mpc85xx-sd-spi-boot
BootROM requires that image on SD card must contain special boot sector.
Implement support for generating this special boot sector directly in
U-Boot start code. Boot sector needs to be at the beginning of the image,
so when compiling only proper U-Boot without SPL then it needs to be in
proper U-Boot. When compiling SPL with proper U-Boot then it needs to be
only in SPL.
Support can be enabled by a new config option FSL_PREPBL_ESDHC_BOOT_SECTOR.
Via other two additional options FSL_PREPBL_ESDHC_BOOT_SECTOR_START and
FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA it is possible to tune how final U-Boot
image could be stored on the SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
This allows U-Boot mvebu-gpio.c driver to switch particular MPP pin into
GPIO mode and enable GPIO support.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The generic ARM relocate_code function was using its own function entry
point as a relocation base, and it was obtaining that address by using
the "adr" instruction on that entry point label.
However that label is not just an ordinary label, instead we explicitly
mark it as a function start address. Normally that doesn't change much
(other than for debugging), but when assembled in Thumb mode, newer
versions of the GNU assembler prepare everything for this address being
used as the argument to a "bx" call, so make sure bit 0 is set in there
to mark this function as Thumb code. Of course this doesn't end up very
well when we use this address for the ensuing memcpy operation.
To avoid this problem, and to solve it in a robust way, add an extra
label, which is not marked as a function entry, and use that for the adr
instruction. This lets all assemblers generate the right immediate offset
in the "adr" instruction.
This fixes in particular ARMv7-M ports when using GNU binutils v2.37 or
newer (commit d3e52e120b68 seems to trigger the change in behaviour).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Jesse Taube <mr.bossman075@gmail.com>
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
