Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Cortina Access parallel Nand support for CAxxxx SOCs
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
CC: Scott Wood <oss@buserror.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the WiseChip Semiconductor Inc. (UG-6028GDEBF02) display
using the SEPS525 (Syncoam) LCD Controller. Syncoam Seps525 PM-Oled is RGB
160x128 display. This driver has been tested through zynq-spi driver.
ZynqMP> load mmc 1 100000 rainbow.bmp
61562 bytes read in 20 ms (2.9 MiB/s)
ZynqMP> bmp info 100000
Image size : 160 x 128
Bits per pixel: 24
Compression : 0
ZynqMP> bmp display 100000
ZynqMP> setenv stdout vidconsole
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
-----BEGIN PGP SIGNATURE-----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=2GYO
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc4
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
tools/efivar.py allows to prepare a file with UEFI variables to preseed
the UEFI variable store.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SPI Flash controller driver for Cortina Access
CAxxxx SoCs
Signed-off-by: Pengpeng Chen <pengpeng.chen@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Vignesh R <vigneshr@ti.com>
CC: Tom Rini <trini@konsulko.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Some commands can get very unweildy if they have too many positional
arguments. Adding options makes them easier to read, remember, and
understand.
This implementation of getopt has been taken from barebox, which has had
option support for quite a while. I have made a few modifications to their
version, such as the removal of opterr in favor of a separate getopt_silent
function. In addition, I have moved all global variables into struct
getopt_context.
The getopt from barebox also re-orders the arguments passed to it so that
non-options are placed last. This allows users to specify options anywhere.
For example, `ls -l foo/ -R` would be re-ordered to `ls -l -R foo/` as
getopt parsed the options. However, this feature conflicts with the const
argv in cmd_tbl->cmd. This was originally added in 54841ab50c ("Make sure
that argv[] argument pointers are not modified."). The reason stated in
that commit is that hush requires argv to stay unmodified. Has this
situation changed? Barebox also uses hush, and does not have this problem.
Perhaps we could use their fix?
I have assigned maintenance of getopt to Simon Glass, as it is currently
only used by the log command. I would also be fine maintaining it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Maxime mentioned that he feels not having the time to be an Allwinner
maintainer anymore. Take over from him.
Maxime, many thanks for your great work in the past! I hope I can still
relay the occasional technical question to you in the future.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
On a board without hardware clock this software real time clock can be
used. The build time is used to initialize the RTC. So you will have
to adjust the time either manually using the 'date' command or use
the 'sntp' to update the RTC with the time from a network time server.
See CONFIG_CMD_SNTP and CONFIG_BOOTP_NTPSERVER. The RTC time is
advanced according to CPU ticks.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add fragment to cover documenation for Xilinx platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Half of this driver is a DM-based timer driver, and half is RISC-V-specific
IPI code. Move the timer portions in with the other timer drivers. The
KConfig is not moved, since it also enables IPIs. It could also be split
into two configs, but no boards use the timer but not the IPI atm, so I
haven't split it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This is a regular timer driver, and should live with the other timer
drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Add support for the hardware pseudo random number generator found in Qualcomm SoC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
Add the STM32MP1 RNG driver in the list of drivers supported by
the STMicroelectronics STM32MP15x series.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add files and directories regex "stm32" and "stm" in "ARM STM STM32MP"
platform to avoid missing files or drivers supported by the
STMicroelectronics series STM32MP15x.
This patch adds the rules already used in Linux kernel for
ARM/STM32 ARCHITECTURE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add MediaTek USB3 Dual-Role controller driver to ARM MEDIATEK,
and add myself as a maintainer for it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
I also followed the development of the SquashFS support in U-Boot
as part of Joao Marcos internship, so I would also appreciate receiving
new contributions and bug reports related to this topic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As I have followed the development of the SquashFS support in U-Boot
as part of Joao Marcos work, it makes sense to get Cc'ed on
contributions/bug reports related to the squashfs support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Import Qualcomm IPQ4019 GCC bindings from Linux.
This will enable using bindings instead of raw clock numbers both in the driver and DTS like Linux does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update MAINTAINERS file for new files.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the current code base is mostly from btrfs-progs, anyone
contributing to U-Boot btrfs code could also help us to improve
btrfs-progs and btrfs kernel module.
Also add myself as designated reviewer.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Add Cortina Access LED controller support for CAxxxx SOCs
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>
Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Python scripts to test 'ls' and 'load' commands. The scripts
generate a SquashFS image and clean the directory after the assertions,
or if an exception is raised.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
