vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
This adds CI tests for SiFive Unleashed board.
QEMU supports booting exact the same images as used on the real
hardware out of the box, that U-Boot SPL loads U-Boot proper
from either an SD card or the SPI NOR flash, hence we can easily
set up CI to cover these 2 boot flows of SiFive Unleashed board.
With this, now we can have regression testing of mmc-spi-slot and
sifive spi drivers, as well as mmc and spi-nor subsystems.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current stable release of LLVM is 12, update to that. While at it,
fix that we had not correctly upgraded to LLVM 11 previously.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Move to gcc-11.1.0 builds from kernel.org for supported platforms and
LLVM-11 for those tests.
- As Heinrich has noted, the RISC-V platform specification has a profile
OS-A for running rich operating systems like Linux and BSD. This profile
requires 64bit and UEFI conforming to the EBBR. Only the 'embedded'
profile may use 32bit. Given this, drop grub for 32bit RISC-V as it no
longer compiles with gcc-11.1 and upstream is unlikely to fix it:
https://www.mail-archive.com/grub-devel@gnu.org/msg30736.html
- Update to grub-2.06 release to address other issues of building with
gcc-11.1.
- Update to newer Xtensa (gcc-9.2.0) and ARC (gcc-10.2) toolchains
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move us up to being based on Ubuntu 20.04 "focal" and the latest tag
from Ubuntu for this release. For this, we make sure that "python" is
now python3 but still include python2.7 for the rx51 qemu build as that
is very old and does not support python3.
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 712cc962b7 ("GitLab: Remove "tags" stanzas") removed the 'all'
tag from all the jobs. The sandbox_noinst_test.py test was added in
between the author date and commit date (commit 6c914e4232
("azure/gitlab: Add tests for sandbox_noinst")) which is probably why it
still contains the tags. This commit fixes that so all jobs now don't
require tags on the GitLab runners.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Given that test/py/requirements.txt has all required test modules, make
use of that rather than a manual pip install list before running our
assorted tool testsuites.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Version 0.9 of OpenSBI provides the system reset extension which allows us
to reset and power off boards without board specific code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Given the structure of our current GitLab tests, we don't make real use
of the tags. Furthermore, these tags prevent the automatic usage of the
default GitLab runners. Remove these tags.
Reported-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add this new board to the test plans. Travis-CI is left out, since it is
being removed soon due to lack of capacity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
There are times where buildman seems to get stuck in this job when in
CI. Forcing single-threaded here allows us to complete and move on.
Signed-off-by: Tom Rini <trini@konsulko.com>
As Stephen is no longer actively maintaining the uboot-test-hooks
repository, switch to using the instance on our GitLab.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Install all requirements according to doc/sphinx/requirements.txt in the
virtual environment used for testing 'make htmldocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SH4 R2Dplus machine configured to test various U-Boot PCI ethernet
options -- RTL8139, EEPRO100, AMD PCnet, DEC Tulip.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we use --test to indicate that tests should be run. It is
better to use a subcommand for list, like binman. Change it and adjust
the existing code to fit under a 'send' subcommand, the default.
Give this subcommand the same default arguments as the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Change to use OpenSBI release v0.8 generic platform images for QEMU
RISC-V CI testing for azure, gitlab and travis-ci.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present we use --test to indicate that tests should be run. It is
better to use a subcommand for list, like binman. Change it and adjust
the existing code to fit under a 'send' subcommand, the default.
Give this subcommand the same default arguments as the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Call pytest3 with argument -ra to display the reason why Python tests are
skipped.
The -r flag displays a test summary info for each test. -ra eliminates
this info for passed tests.
Pros an cons were discussed in:
https://lists.denx.de/pipermail/u-boot/2020-June/417090.html
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Qemu tests for the MIPS Malta machine as a replacement for
the deprecated generic MIPS machine.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch contains test/nokia_rx51_test.sh script which automatically
download and compile all needed tools in local temporary directory to
generate a simple MTD images for booting Maemo kernel image by U-Boot from
RAM, eMMC and OneNAND. MTD images are then run in virtual n900 machine
provided by qemu-linaro project.
This script does not need any special privileges, so it can be run as
non-root nobody user.
It can be used to check that U-Boot for Nokia N900 is not broken and can be
successfully booted in emulator.
Script is registered to .azure-pipelines.yml, .gitlab-ci.yml and
.travis.yml so it would be automatically run on those CI services.
Signed-off-by: Pali Rohár <pali@kernel.org>
At this point LLVM-7 is rather old. Switch over to LLVM-10 to enable
some amount of CI coverage with newer compilers.
Signed-off-by: Tom Rini <trini@konsulko.com>
It does not seem to be necessary to run buildman again to show errors,
since any errors can be shown by the first invocation and there is only
a single board being built. Update this to simplify the code, using the
-e flag to make sure errors are shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
It seems unnecessary to read the exit code and then check it again. Drop
this and just let the test.py provide the exit code directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can use the -W flag to tell buildman to ignore warnings. Since we also
have -E defined, compiler warnings are promoted to errors, so they will
still cause a failure. But migration warnings of the form:
===================== WARNING ======================
This board does not use CONFIG_DM. CONFIG_DM will be
compulsory starting with the v2020.01 release.
Failure to update may result in board removal.
See doc/driver-model/migration.rst for more info.
will now be ignored.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 329f5ef51d (travis.yml: run buildman with option -E)
Reviewed-by: Tom Rini <trini@konsulko.com>
Bash allows for variables to expand only if non-empty:
$ var=test
$ echo ${var:+"$var"}
test
$ echo ${var:+"-k $var"}
-k test
$ var=
$ echo ${var:+"-k $var"}
Use this feature to avoid the workaround.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Avoid needing to know about the internal .bm-work directory, by passing
the -w flag to buildman.
This is not needed on travis since the -w flag is already used (from a
previous patch).
Drop the -P flag since this has no effect if -w is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since TEST_PY_BD is always defined we can drop this check.
This does not affect travis since it has a single, unified script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not needed in the test.py part of the config, now since we use the
same name as the pytests.
Drop BUILDMAN, retaining it only for the 'build' parts of the config, i.e.
where we build multiple boards and don't run any tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current method of selecting the board to build with test.py is a bit
error-prone, e.g. with "^sandbox$" it actually builds 5 boards (all of
those in the sandbox architecture).
Use the (newish) --board flag instead, to get the same result.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Avoid needing to know about the internal .bm-work directory, by passing
the -w flag to buildman.
This does not affect travis since the previous commit already used the -w
flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds QEMU RISC-V 32/64 SPL testing. Unlike QEMU RISC-V 32/64,
we test SPL running in M-mode and U-Boot proper running in S-mode,
with a 4-core SMP configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
