distutils is about to meet its demise [1]. Switch to setuptools.
[1] https://peps.python.org/pep-0632/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Add dm_serial driver source code for S5P4418 SOC. Extend the "arm,pl011"
driver by init of UART-clock and UART-reset.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Switch off SCSI related config options to get rid of the board
removal warning. We don't use this interface. Also disable UBIFS
to decrease the image size, as this is also not used.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
EEPROM detection logic in ti_i2c_eeprom_get() involves figuring out
whether addressing is 1-byte or 2-byte. There are currently different
behaviours seen across boards as documented in commit bf6376642f
("board: ti: common: board_detect: Fix EEPROM read quirk"). Adding to
the list, we see that there are 2-byte EEPROMs that read properly
with 1-byte addressing with no offset.
For ti_i2c_eeprom_am6_get where eeprom parse operation is dynamic, the
earlier commit d2ab2a2baf ("board: ti: common: board_detect: Fix
EEPROM read quirk for AM6 style data") tried to resolve this by running
ti_i2c_eeprom_get() twice. However this commit along with its former
commit fails on J7 platforms where EEPROM successfully return back the
header on 1-byte addressing and continues to do so until an offset is
introduced. So the second read incorrectly determines the EEPROM as
1-byte addressing.
A more generic solution is introduced here to solve
this issue: 1-byte read without offset and 1-byte read with offset. If
both passes, it follows 1-byte addressing else we proceed with 2-byte
addressing check.
Tested on J721E, J7200, DRA7xx, AM64x
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Fixes: d2ab2a2baf (board: ti: common: board_detect: Fix EEPROM read quirk for AM6 style data)
Fixes: bf6376642f (board: ti: common: board_detect: Fix EEPROM read quirk)
Tested-By: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Add the CONFIG_SYS_NAND_SELF_INIT to the Kconfig to follow the changes from
mainline.
Signed-off-by: Lokanathan, Raaj <raaj.lokanathan@intel.com>
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
U-Boot serial code already handles -EAGAIN value from getc and putc
callbacks. So change drivers code to return -EAGAIN when HW is busy instead
of doing its own busy loop and waiting until HW is ready.
Signed-off-by: Pali Rohár <pali@kernel.org>
serial-uclass.c code already puts \r before \n for all dm_serial drivers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support Holtek HT1380/HT1381 Serial Timekeeper Chip. It provides seconds
, minutes, hours, day of the week, date, month and year information.
Datasheet:
https://www.holtek.com.tw/documents/10179/11842/ht1380_1v130.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All uniphier v7 SoCs have cortex-a9 and use cortex-a9 global timer
in a simple implementation. Now DM_TIMER of it is available
on 35751c7f3f ("timer: sti: convert sti-timer to arm a9 global timer"),
so let's switch to it.
The old driver reads the lower 32bits of counter field
and sets the prescaler as 50 with PERIPHCLK(=50MHz),
so the global timer works as a 32-bit 1MHz timer.
The DM_TIMER uses the whole 64bits with no prescaler,
so the global timer works as a 64-bit PERIPHCLK timer.
CONFIG_SYS_HZ_CLOCK is set as the default PERIPHCLK frequency,
if there is no 'clocks' property in devicetree.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
PXs3 Ref boards need to change the strength of ethernet ports
for stability, like LD20's one.
This adds the table data and fixes the boot issue on PXs3 Ref board.
Fixes: 0852033309 ("ARM: uniphier: sync with Linux 5.8-rc4")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
The pinctrl datas of uniphier SoCs are the minimal subsets of kernel's one,
and some tables has no data to save the footprint size.
If the board dts tries to match a pin name on no pins defined SoC,
the footprint magic code causes "Synchronous Abort".
This checks if the 'pins' data is valid,
and if empty, avoids the abort with the warning as follows:
WARNING at drivers/pinctrl/uniphier/pinctrl-uniphier-core.c:36/uniphier_pinctrl_get_pins_count()!
pinctrl_select_state_full: pinctrl_config_one: err=-38
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
The 'base' GPIO controller property is unused in u-boot and Linux. It is
also not documented in the binding. So drop it.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
'active_clk_edges' and 'chipselect_num' SPI controller properties are
unused in u-boot and Linux. They are also not documented in the binding.
So drop them.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
kmcent2-u-boot.dtsi file contains copy of powerpc u-boot.dtsi binman file.
So remove code duplication and replace it by including u-boot.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The correct value for 'entry-method' in the idle-states binding is 'psci',
not 'arm,psci'. It hasn't mattered because it isn't used by the OS.
Signed-off-by: Rob Herring <robh@kernel.org>
The "arm,armv7-timer-mem" schema defines the address sizes for child
nodes to be 32-bit as there's no need for 64-bit offsets and sizes of
the child 'frame' nodes.
Signed-off-by: Rob Herring <robh@kernel.org>
DT node names should follow generic names defined in the DT spec. These
are also now checked by dtschema tools.
Signed-off-by: Rob Herring <robh@kernel.org>
Add the definition of the pinctrl for the MCU domain.
Same as kernel commit 500e6dfbb465531150ac6e2ff0856dd357ddc8a4
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
To quote the author:
This series adds support for using configs with the source command.
And to paraphrase the rest, see the patch commit messages for more
details.
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simplifies a few lines and corrects an error message.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two callers of image_source_script specify an image name. However, both
use the deprecated @ syntax, indicating that they have not been updated
in a while. If CONFIG_FIT_SIGNATURE is enabled, we will reject such
names outright. Back in commit 152576a598 ("stm32mp: stm32prog: handle
U-Boot script in flashlayout alternate"), we even renamed one of the
nodes. Instead of hard-coding a script image name, just use the default
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds a basic test for FIT image handling by the source command.
It's a python test becase we need to run mkimage.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fallback for this function so it can be used without regard to
whether FIT_SIGNATURE is enabled or not.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Bring in the final series to complete the main portion of migrating
CONFIG symbols to either Kconfig or CFG namespace (or removing /
renaming entirely). With this, we have stricter CI tests as well now.
We ask for CONFIG_SPL_LOAD_FIT_ADDRESS in Kconfig, so we cannot define
it in C as a fall-back. However, this option previously was buried under
"if ... endif" Kconfig logic. Rework a number of config options to now
have more robust dependency lines so that we can ask this address when
needed. With that done, we can remove the fallback in spl_ram.c.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is never changed by boards, so just rename it to
SPI_IDLE_VAL to fit with the rest of the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the symbol CONFIG_SEND_ENABLE to just SEND_ENABLE, and remove
the second whitespace following the define.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point all listed adhoc CONFIG symbols have been migrated to
Kconfig or removed from the tree or renamed to CFG (or similar). We also
now have CI tests that will error on any new introductions, and
checkpatch.pl also looks. We can now remove these hooks and related
scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all symbols have been migrated to Kconfig, or are part of the
CFG namespace we do not need a complex check for unmigrated CONFIG
symbols. Any instance of #define (or #undef) or a CONFIG value is wrong,
so cause CI to fail.
This test is not as strict as possible yet as we have more symbols that
were not previously caught to deal with.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all CONFIG symbols are in Kconfig, checkpatch.pl should check
for and error on any case of define/undef CONFIG_*.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in the conversion there should be no need to have logic to
disable some symbol during the SPL build as all symbols should have an
SPL counterpart.
The main real changes done here are that we now must make proper use of
CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we
developed prior to CONFIG_IS_ENABLED() being available.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of CONFIG symbols have crept in that are never referenced in
code, so drop them here. Further, we have two symbols being enabled
in headers while already enabled correctly in Kconfig, so these lines
can also be removed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename the CONFIG_POWER_BD71837_I2C_* symbols to not have the CONFIG
prefix and be local to the file they are used in.
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform simple renames of:
CONFIG_WATCHDOG_PRESC to CFG_WATCHDOG_PRESC
CONFIG_WATCHDOG_RC to CFG_WATCHDOG_RC
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform simple renames of:
CONFIG_VSC7385_IMAGE to CFG_VSC7385_IMAGE
CONFIG_VSC7385_IMAGE_SIZE to CFG_VSC7385_IMAGE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
