Commit Graph

2050 Commits

Author SHA1 Message Date
Udit Agarwal
73fbcdf163 armv8: LS2080ARDB: Add secure boot defconfig for QSPI boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: dropped redundant commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Udit Agarwal
15e7c681e1 LS2080ARDB: QSPI boot: Secure Boot image validation
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Ashish Kumar
63b2316c5c fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.

This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Madalin Bucur
10710b4ec5 armv8: ls1043/ls1046aqds: add support for RGMII_TXID
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: York Sun <york.sun@nxp.com>
2017-09-07 13:23:52 -05:00
Breno Lima
3aa4b703b4 imx: imx6: Move gpr_init() function to soc.c
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28 09:48:53 +02:00
Angelo Dureghello
c74dda8b44 m68k: mcf5445x: move early ddr init as board-specific
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init
is required. This patch moves this ddr/sdram early initalization
away from start.S (to be board related).

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-08-18 01:26:08 +02:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Simon Glass
723806cc5b env: Rename some other getenv()-related functions
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:

   getenv_vlan()
   getenv_bootm_size()
   getenv_bootm_low()
   getenv_bootm_mapsize()
   env_get_default()

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:31:11 -04:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Simon Glass
018f530323 env: Rename common functions related to setenv()
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:32 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Breno Lima
6efb613373 mx6sabreauto: Fix IOMUXC_GPR6 and IOMUXC_GPR7 values
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */

Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
2017-08-16 11:44:18 +02:00
Breno Lima
a500a33115 mx6sabresd: Fix IOMUXC_GPR6 and IOMUXC_GPR7 values
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */

Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
2017-08-16 11:43:15 +02:00
Simon Glass
203e94f6c9 env: Add an enum for environment state
At present we have three states for the environment, numbered 0, 1 and 2.
Add an enum to record this to avoid open-coded values.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 08:18:51 -04:00
Simon Glass
0649cd0d49 Move environment files from common/ to env/
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 08:18:45 -04:00
Philipp Tomsich
b529993e02 spl: add hierarchical defaults for SPL_LDSCRIPT
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.

As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig.  Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:37 +02:00
Hou Zhiqiang
acb90e8338 fsl-lsch2: csu: correct the workaround A-010315
The implementation of function set_pcie_ns_access() uses a wrong
argument. The structure array ns_dev has a member 'ind' which is
initialized by CSU_CSLX_*. It should use the 'ind' directly to
address the PCIe's CSL register (CSL_base + CSU_CSLX_PCIE*).

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:33 -07:00
Santan Kumar
7794d9ab29 board: ls2080ardb: Add fsl_fdt_fixup_flash
IFC and QSPI are muxed on board. Add fsl_fdt_fixup_flash() to disable
IFC node in dts if QSPI is enabled, or disable QSPI node in dts if
otherwise.

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
Hou Zhiqiang
e4b5143eb6 fsl-lsch2: csu: remove multiple calling function
Function enable_layerscape_ns_access() is alreayd called soc-wide.
Remove duplicated calling from individual boards.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
Santan Kumar
263536a693 board:ls2080ardb: Update execution of config_board_mux
Function config_board_mux() reads env variable 'hwconfig' which is
only available after relocation for QSPI boot. Move calling
config_board_mux() to misc_init_r().

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:55:02 -07:00
Santan Kumar
6cc914efd2 board/ls2080ardb: Disable SD-related GPIO programming
Smart voltage translator is removed from LS2080ARDB/LS2088ARDB
RevF boards. It is only used on LS2081ARDB. Programming GPIO
is only required for LS2081ARDB.

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:54:43 -07:00
Qianyu Gong
3016084b38 armv8: ls1046ardb: update core frequency to 1800MHZ
Update the default core frequency to 1800MHZ for best performance under
SD boot and eMMC boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:11:34 -07:00
Tom Rini
9f841559a5 qemu-ppce500: Update get_phys_ccsrbar_addr_early()
The logic of what fdt_get_base_address() will search for and return has
changed.  Rework get_phys_ccsrbar_addr_early() to perform the logic that
fdt_get_base_address used to perform.

Fixes: 336a44877a ("fdt: Correct fdt_get_base_address()")
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-03 14:48:52 -04:00
Sumit Garg
76bbf1c634 arm64: ls1043ardb: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
nor/qspi boot in case of secure boot. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-01 08:28:57 -07:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Fabio Estevam
3f0a1042bb mx6sabreauto: Make Ethernet functional again
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.

This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.

However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.

This is the equivalent fix from commit 4b6035da48 ("mx6sabresd: Make
Ethernet functional again").

Reported-by: Miquel RAYNAL <miquel.raynal@free-electrons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-13 15:05:49 +02:00
Diego Dorta
07f6ddb67a mx6sabreauto: Add Falcon mode support
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-12 10:28:19 +02:00
Fabio Estevam
ca62e5d043 mx6sabreauto: Do not enable WEIM by default
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.

I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.

Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:

imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517

By keeping WEIM disabled in U-Boot these kernel issues are gone.

Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-12 10:21:10 +02:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Vanessa Maegima
d7c11502df mx6sabreauto: Update to SPL only mode
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.

This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Vanessa Maegima
823dff9d02 mx6qsabreauto: Add SPL support
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.

Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg

Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg

Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg

Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Gautam Bhat
d8fab10cb4 mx7dsabresd: Set VLD04 output to 2.8V in PMIC initialization.
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.

Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-12 09:44:22 +02:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Heiko Schocher
064b55cfcb powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-16 10:14:55 -04:00
Masahiro Yamada
51855e8981 treewide: remove unneeded semicolons
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-06-16 10:11:38 -04:00
York Sun
1079af4817 powerpc: fsl: Update maintainers
Update maintainers for B4860QDS, P1010RDB, P1_TWR, T104xRDB.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:37 -07:00
York Sun
5a4ff0d9ef powerpc: mpc8569mds: Update config and maintainer
Enable DHCP command by default. Update maintainer info.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:37 -07:00
York Sun
cdab5e909a powerpc: mpc8568mds: Update board config
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:37 -07:00
York Sun
8b7261f84c powerpc: mpc8536ds: Update maintainer
Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:37 -07:00
York Sun
853f6a8770 powerpc: mpc8544ds: Update maintainer
Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:37 -07:00
York Sun
531aaaec28 powerpc: mpc8548cds: Update maintainer
Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 12:18:36 -07:00
York Sun
c58635add8 powerpc: mpc86xx: Update maintainer for MPC8610HPCD and MPC8641HPCN
Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 11:30:00 -07:00
York Sun
3eaaa718e7 powerpc: mpc85xx: Update maintainer for MPC8541CDS and MPC8555CDS
Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 11:30:00 -07:00
York Sun
3913191c8a powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS
Drop support for these two legacy boards.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-12 11:30:00 -07:00
Simon Glass
6e2941d787 common: freescale: Move arch-specific declarations
The declarations should not be in common.h. Move them to the arch-specific
headers.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 12:30:55 -04:00
Simon Glass
c62db35d52 arm: Add explicit include of <asm/mach-types.h>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:36 -04:00
Tom Rini
541f538f4c Merge git://git.denx.de/u-boot-fsl-qoriq 2017-06-03 18:05:04 -04:00
York Sun
399e2bb60c armv8: layerscape: Make U-Boot EL2 safe
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:24 -07:00
Santan Kumar
1f55a93802 armv8: ls2080aqds: Add support for SD boot
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-06-01 19:57:17 -07:00
Bogdan Purcareata
33a8991a87 drivers: net: fsl-mc: Link MC boot to PHY_RESET_R
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.

Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.

Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-06-01 19:55:50 -07:00