- Migrate SYS_I2C_SH and related defines to Kconfig
- Remove currently unused SYS_I2C_SH related defines
- Cleanup related README section.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Signed-off-by: Tom Rini <trini@konsulko.com>
On this platform, we have DM_I2C and SPL_DM_I2C always enabled.
Remove legacy options.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
There are no users of more than 1 i2c bus in the non-DM case currently.
Remove the additional defines for this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on
SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either
something that needs to exist for real, or shouldn't be called.
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the legacy software i2c support is only used for a single bus.
Remove all of the extra and unused support. Also update the README to
not reference that, and finish removing some already badly auto-edited
related text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_I2C_SOFT
CONFIG_SYS_I2C_SOFT_SPEED
CONFIG_SYS_I2C_SOFT_SLAVE
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform defines everything needed to be able to use the
eeprom command. In addition, board/compulab/common/eeprom.c is required
by the platform, and does not use CONFIG_ID_EEPROM to enable/disable
builing of it. In order to migrate CONFIG symbols to Kconfig and to not
have to add complex logic to handle this case, enable CMD_EEPROM on this
board.
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
Finish moving this driver to Kconfig.
- Update the dependency logic for Exynos5 too
- Remove the unused CONFIG_SYS_I2C_S3C24X0_SPEED variable
- Drop CONFIG_SYS_I2C_S3C24X0_SLAVE as it's always set to 0.
- Move the internal SYS_I2C_S3C24X0_SLAVE define closer to the only user.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The instances of CONFIG_SYS_I2C_EEPROM_ADDR on these platforms doesn't
match up with the rest of the EERPOM related defines in U-Boot. Move
these out of the CONFIG namespace rather than make complex Kconfig
logic.
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
As the code reads now, making this code path use
CONFIG_SYS_IVM_EEPROM_ADR rather than CONFIG_SYS_I2C_EEPROM_ADDR seems
to make sense as the rest of the EEPROM infrastructure isn't used on
these platforms.
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
The shc platforms do not make use of the rest of the EEPROM
infrastructure. Rather than make more elaborate Kconfig logic, remove
this setting from the CONFIG namespace.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Looking over the current boards, there are no users of
CONFIG_MAC_ADDR_IN_EEPROM. Further, omapl138_lcdk uses
CONFIG_NET_RANDOM_ETHADDR. Drop various unused code paths.
Cc: Adam Ford <aford173@gmail.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform does not use any of the standard EEPROM functionality and
instead provides its own. Use a local namespace for the I2C related
defines to access the EEPROM.
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Rework the default environment a bit to not use non-standard
CONFIG_ENV_... names and similar one-off CONFIG names.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename CONFIG_ENV_KS2_BOARD_SETTINGS to ENV_KS2_BOARD_SETTINGS so that
it better fits with the rest of the environment addition macros.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename CONFIG_EXTRA_ENV_BOARD_SETTINGS to EXTRA_ENV_BOARD_SETTINGS in
order to not further add to the CONFIG namespace.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There are a number of DWC2 configuration options that are set in dwc2.h
and referenced in dwc2.c only. Move these out of the CONFIG_DWC2
namespace and in to the DWC2 namespace. Note that hikey was defining an
option that was already always enabled, so we can remove that hunk.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
There is no space in OCM for SPL stack because the space in OCM is occupied
by TF-A. That's why move relocate stack to DDR to 0x18000000 address
and also enable SPL_SIZE_LIMIT not to be more then 0xfffea000 which is
default address for TFA.
It is good to summarize current DDR usage in SPL flow.
0-0x80000 is used for BSS
(CONFIG_SPL_BSS_START_ADDR, CONFIG_SPL_BSS_MAX_SIZE)
0x100000 is used for DTB passing address
(CONFIG_XILINX_OF_BOARD_DTB_ADDR)
0x17fffe70 - CONFIG_SPL_STACK_R_ADDR - is used for GD
0x18000000 is used for SPL stack
(CONFIG_SPL_STACK_R_ADDR)
0x20000000-0x21000000 is used for SPL malloc area
(CONFIG_SYS_SPL_MALLOC_START, CONFIG_SYS_SPL_MALLOC_SIZE)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use TF-A instead of ATF in description. And update generic description with
removing ATF because also configurations without it are supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot support board detection at run time and based on it change DT.
This feature is implemented for SOM Kria platforms which contain two
eeproms which contain information about SOM module and CC (Carrier card).
Full U-Boot starts with minimal DT file defined by
CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image.
It is using default setup of board_name variable initializaed to
DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option.
When DTB_RESELECT is enabled board_detection() is called. Keep it your mind
that this code is called before relocation. board_detection() is calling
xilinx_read_eeprom() which fills board_info (xilinx_board_description)
structure which are parsed in board_name_decode().
Based on DT configuration and amount of nvmemX aliases name of the board is
composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev"
<board_revision> "-" <cc_name> "-rev" <cc_revision>.
If CC is not present or more are available it keeps going.
When board name is composed and returned from board_name_decode() it is
assigned to board_name variable which is used by
board_fit_config_name_match() which is called via fdtdec_setup() when it
goes over config options in multi dtb FIT image.
From practical point of view multi DTB image is key point here which has to
contain configs for detected combinations. Unfortunately as of now they
have to be full DTBs and DTBOs are not supported.
That's why configuration like:
config_X {
description = "zynqmp-board-cc";
fdt = "board", "cc";
};
needs to be squashed together with:
fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \
arch/arm/dts/zynqmp-cc.dtbo
and only one dtb is in fit:
config_X {
description = "zynqmp-board-cc";
fdt = "board-cc";
};
For creating multi DTBs fit image use mkimage -E, e.g.:
mkimage -E -f all.its all.dtb
When DTB_RESELECT is enabled xilinx_read_eeprom() is called before
relocation and it uses calloc for getting a buffer. Because this is dynamic
memory it is not relocated that's why xilinx_read_eeprom() is called again
as the part of board_init(). This second read with calloc buffer placed in
proper position board_late_init_xilinx() can setup u-boot variables as
before.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When MULTI_DTB_FIT is enabled fit-dtb.blob fit image is created which
contain all DTBs listed by CONFIG_OF_LIST. And with DTB_RELESELECT there is
a need to handle it as one file with DTBs in it not as separate DTBs in
u-boot.its/itb.
That's why extend mkimage_fit_atf.sh to generate u-boot.itb correctly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Start of DTB should be 64bit aligned that's why also make sure that end is
also 64bit aligned. It is not required but it is nice thing to do.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling MULTI_DTB_FIT and DTB_RESELECT can end up with multi DTBs in FIT
image placed and aligned only by 32bits (4bytes). Based on device tree
specification:
"Specifically, the memory reservation block shall be aligned to an 8-byte boundary
and the structure block to a 4-byte boundary."
is 64bit (8bytes) alignment required. That's why make sure that
fit-dtb.blob and u-boot.itb as our primary target images for Xilinx ZynqMP
are all 64bit aligned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
DT needs to be 64bit aligned. If it is not fdt64_to_cpu will fail when try
to read information about reserved memory. The system ends in exception
without any clue what's going it. That's why detect not aligned DT and
panic to show where the issue is coming from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for changing DT at run time. It is done via board_detection()
which returns platform_id and platform_version which can be used via
board_name_decode() to compose board_local_name string which corresponds
with DT which is should be used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Origin code was allocating only pointers to struct xilinx_board_description
and there was separate allocation for structure self and freeing in case of
failure.
The code is directly allocating space for all structures by one calloc to
simlify logic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use variable which points to DEVICE_TREE by default. The reason for this
change is to enable DTB_RESELECT and MULTI_DTB_FIT where board detection
can be used for change DTB at run time. That's why there must be reference
in board_fit_config_name_match() via variable instead of hardcoding it
which is sufficient for that use case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
FRU spec expected \0 for unused symbols but unfortunately a lot of boards
are using spaces instead of \0. That's why after saving it to desc->name
name is checked again and all spaces are converted to \0. This will ensure
that names can be used for string manipulations like concatenation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dev_dbg, dev_err and dev_warn seems to be moved to different header file.
Include dm/device_compat.h file to compile properly.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The commit 573a3811ed ("sysreset: psci: support system reset in a generic
way with PSCI") has added support for warm reset via PSCI but this hasn't
been reflected in usage message and user has to look at the code how to run
it. That's why update usage text to make this clear.
Here is full help with updated usage:
ZynqMP> help reset
reset - Perform RESET of the CPU
Usage:
reset - cold boot without level specifier
reset -w - warm reset if implemented
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
The first name is taken from command name that's why shouldn't be listed in
help. And commands shouldn't be listed with <> which means value but value
itself is command name.
Also add description for commands to make it clear what it does.
Before
pwm pwm <invert> <pwm_dev_num> <channel> <polarity>
pwm <config> <pwm_dev_num> <channel> <period_ns> <duty_ns>
...
After:
pwm invert <pwm_dev_num> <channel> <polarity> - invert polarity
pwm config <pwm_dev_num> <channel> <period_ns> <duty_ns> - config PWM
pwm enable <pwm_dev_num> <channel> - enable PWM output
pwm disable <pwm_dev_num> <channel> - disable PWM output
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
