When OP-TEE is used, the SMC for BSEC management are not available and
the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13
and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe
and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle
the BSEC_LOCK_PERM lock value instead of 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Adds DT binding documentation for the TI Error Location Module.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-8-rogerq@kernel.org
Add DT binding documentation for the TI GPMC NAND controller.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-4-rogerq@kernel.org
As discussed previously [1,2], the source command is not safe to use with
verified boot unless there is a key with required = "images" (which has its
own problems). This is because if such a key is absent, signatures are
verified but not required. It is assumed that configuration nodes will
provide the signature. Because the source command does not use
configurations to determine the image to source, effectively no
verification takes place.
To address this, allow specifying configuration nodes. We use the same
syntax as the bootm command (helpfully provided for us by fit_parse_conf).
By default, we first try the default config and then the default image. To
force using a config, # must be present in the command (e.g. `source
$loadaddr#my-conf`). For convenience, the config may be omitted, just like
the address may be (e.g. `source \#`). This also works for images
(`source :` behaves exactly like `source` currently does).
[1] https://lore.kernel.org/u-boot/7d711133-d513-5bcb-52f2-a9dbaa9eeded@prevas.dk/
[2] https://lore.kernel.org/u-boot/042dcb34-f85f-351e-1b0e-513f89005fdd@gmail.com/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To make things more human readable, say "changesets from" rather than
"csets from" in all our historical pages here. Moving forward this has
been changed in our gitdm with b034e399e31a ("gitdm: fix typo csets").
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sphinx supports generating Texinfo sources and Info documentation,
which can be navigated easily and is convenient to search (via the
indexed nodes or anchors, for example). This is basically the same as
1f050e904dd6f2955eecbd22031d912ccb2e7683, which was recently applied
to the Linux kernel.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
qemu can emulate also e500v1 core but cannot emulate CPUs from Freescale
PowerPC QorIQ T and P series.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Texas Instrument's entire K3 generation of SoCs use much of the same
frameworks and boot flow, especially at the uboot level. Though there
are small differences introduced as each new K3 based SoC is developed
and as the K3 generation matures that will also need to be documented.
Rather than copying the same documentation, with the small differences
applicable to that specific SoC to a new page, introduce a new K3
page that can describe the general boot flow and design decisions for
the entire K3 generation of chips, leaving the specifics for that
particular SoC to a unique sub-page below this one.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Texas Instruments produces quite a lot of SoCs based upon a common
architecture 'generation'. (eg: OMAP, K3) TI's existing documentation
layout makes noticing this generation jump rather difficult.
To make navigation easier, split the existing documentation into
individual SoC families so we may begin grouping them according to their
generational (eg: OMAP, K3) families.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_MONITOR_IS_IN_RAM
As part of this, reword some of the documentation slightly to reflect
that this is in Kconfig and not a define now.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FLASH_SPANSION_S29WS_N
CONFIG_FLASH_VERIFY
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
CONFIG_FSL_ISBC_KEY_EXT
CONFIG_FSL_TRUST_ARCH_v1
CONFIG_FSL_SDHC_V2_3
CONFIG_MAX_DSP_CPUS
CONFIG_MIU_2BIT_INTERLEAVED
CONFIG_SERIAL_BOOT
CONFIG_SPI_BOOTING
CONFIG_X86EMU_RAW_IO
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is only used on one platform currently. However, with PHYLIB
enabled, which this platform also does, this option is not checked and
the functional use case is handled. Remove this code.
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'Configuration' heading should be on level 2, not on level 1.
Fixes: eaa268589e ("doc: man-page for the printenv command")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently the sound command accepts only one value each for duration and
frequency. Allowing more duration and frequency arguments enables playing a
tune.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI Conformance Profile Table entry for EBBR appears in v2.1.0 of the
EBBR specification[1]. Update naming accordingly.
While at it, update the EBBR version referenced in the documentation.
[1]: https://github.com/ARM-software/ebbr/releases/tag/v2.1.0
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix a few typos spot during a first read of the contribution process.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Since the commit d5ba6188df ("cmd: pxe_utils: Check fdtcontroladdr
in label_boot") the FDT or the FDTDIR label is required in extlinux.conf
and the fallback done by bootm command when only the device tree present
in this command parameters is no more performed when FIT is used for
kernel.
When the label FDT or FDTDIR are absent or if the device tree file is
absent, the PXE command in U-Boot uses the default U-Boot device tree
selected by fdtcontroladdr = gd->fdt_blob, it is the "Scenario 3".
With this scenario the bootm FIP fallback is no more possible with
the extlinux.conf when only "kernel" label is present and is a FIP:
kernel <path>#<conf>[#<extra-conf[#...]]
As the U-Boot FDT is always provided in the third bootm argument,
the device tree found in FIP is not used as fallback, it was done
previously in boot_get_fdt().
This patch adds a new field kernel_label to save the full kernel label.
The FDT bootm parameters use the kernel address (to avoid to load a
second time the same FIP) and the config when this full label is reused
for "fdt" or "initrd" label.
This FIP support in extlinux.conf is restored when the "FDT" label
can be found and select the same FIP (identical file and configuration):
kernel <path>#<conf>[#<extra-conf[#...]]
fdt <path>#<conf>[#<extra-conf[#...]]
The patch add also this possibility for initrd.
initrd <path>#<conf>[#<extra-conf[#...]]
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a man-page for the sound command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commits adds the description for the UEFI Secure Boot
Configuration through the eficonfig menu.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Redacted the complete document.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* BASH code should be labeled as such.
* Code blocks should be indented by 4 spaces.
Fix these here.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add documentation for the wget command.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Convert the buildman documentation to rST format and include it in the
'build' section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <foss+uboot@0leil.net>
The word tuples might be misleading.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add example command how to compile U-Boot and add new documentation section
describing how to enable early debug UART and verbose log output for N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
