Freescale application note AN3638 describes an update to the NXID format,
which stores MAC addresses and related data on an on-board EEPROM. The new
version adds support for up to 23 MAC addresses, instead of just 8. Since
the initial implementation of NXID had a "0" in the 'version' field, this
new version is called "v1".
Boards that are shipped with EEPROMs in the NXID v1 format should define
CONFIG_SYS_I2C_EEPROM_NXID_1 instead of CONFIG_SYS_I2C_EEPROM_NXID.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
pumping line-rate traffic though a p4080 rev.2, which
is configured to encrypt packets prior to forwarding through
an IPsec tunnel, gets this error:
of_platform ffe302000.jq: DECO: desc idx 22: LIODN error. DECO was trying
to share from itself or from another DECO but the two Non-SEQ LIODN
values didn't match or the "shared from" DECO's Descriptor required that
the SEQ LIODNs be the same and they aren't.
Since high traffic rates cause DECOs to begin to start sharing
shared descriptors amongst themselves, and DECOs inherit job queue
LIODNs when accessing shared descriptors, and a recently discovered
rev.2 h/w erratum requires all sharing job queues in a partition
have same liodn assignment, reassign the first job queue's liodn
assignment to the rest.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We configure the controller but dont have virtual address space thus any
devices on the 4th controller are not accessible in u-boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Make the U-Boot update command sequence conditional. Helps prevent
accidental erasing if an upload or previous step fails
* Make it easier to update other FLASH banks
* Enable DDR controller cache line interleaving and bank cs0/cs1 by default
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the code which writes to the on-board EEPROM so that it can detect if
the write failed because the EEPROM is write-protected. Most of the 8xxx-class
Freescale reference boards use an AT24C02 EEPROM to store MAC addresses and
similar information. With this patch, if the EEPROM is protected, the
"mac save" command will display an error message indicating that the write
has not succeeded.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original code maps boot flash as non-cacheable region. When calling
relocate_code in flash to copy u-boot from flash to ddr, every loop copy command
is read from flash. The flash read speed will be the bottleneck, which consuming
long time to do this operation. To resovle this, map the boot flash as
write-through cache via tlb. And set tlb to remap the flash after code
executing in ddr, to confirm flash erase operation properly done.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_ENV_SIZE of MPC8569MDS was wrongly set to CONFIG_ENV_SECT_SIZE which
is 128KB, so it took longer time to do crc32 calculation for ENV than it should
do. It causes the bootup for MPC8569MDS significantly slow. This patch fixs it
to 0x2000(8KB), also fix the comment for CONFIG_ENV_SECT_SIZE to correct size.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
and clean up error messages and help,
removed pointless debug() call.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch introduces an extra mask-field in spansion_spi_flash_params
to support flash chips with 1-byte extended ID (like the S25FL032P).
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The spansion_erase currently only works when the sector size is 64KB.
cmd[1] should contain the higher 8 bit of the 24 bit address of the
sector to be erased. Currently it is holding the sector index to be
erased which happens to be the same thing when the sector size is
64KB.
Signed-off-by: Marc-Andre Hebert <marc-andre.hebert@humanware.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
uint is typedefed twice if __MACH__ is defined. This generates an error
when calling MAKEALL for netstar bord on OS X.
This patch removes the typedef for __MACH__ case in favor of general
definiton some lines below.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Fix bug where signed data was processed as unsigned. The bug previously
resulted in negative temperature readings wrapping around, eg -10 became
245.
Signed-off-by: Jeff Dischler <jdischler@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Poll the ds1621 NV Memory Busy bit instead of waiting a static amount of
time for register writes.
Also add config retister bit defines.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds a new config parameter for adjusting the calculation of
hash table size when importing a buffer.
When importing a extremely small buffer (e.g. the default_environment)
the old calculation generated a hash table which could hold at most the
buffer content but no more entires.
The new calculation add a fixed number of entries to the result to fit
better for small import buffers. This amount may be configured by the
user in board file to adjust the behaviour.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
The current ELF loading function does a lot of work above and beyond a
simple "loading". It ignores the real load addresses and loads things
into their virtual (runtime) address. This is undesirable when we just
want it to load an ELF and let the ELF do the actual C runtime init.
So add a command line option to let people choose to load via either the
program or section headers. I'd prefer to have program header loading
be the default, but this would break historical behavior, so I'll leave
section header loading as the norm.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes the compilation problem introduced with commit
e3c78c9b [ppc4xx: Remove now unused CONFIG_UART1_CONSOLE]:
-> ./MAKEALL TB5200
Configuring for TB5200 board...
serial.c: In function '__default_serial_console':
serial.c:94: warning: no return statement in function returning non-void
I accidentally removed an "#else" line. This patch adds it back.
Signed-off-by: Stefan Roese <sr@denx.de>
commit ea882baf9c introduces
a command_sub_table for the "env" command. On arm, avr32, m68k,
mips and sparc architectures, relocation needs manual fixups,
so add these fixups for this sub command table too.
Tested on arm/qong board.
mips board (Ben NanoNote) from Xiangfu Liu
arm/AT91 board from Reinhard Meyer
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
cc: Xiangfu Liu <xiangfu@openmobilefree.net>
cc: Reinhard Meyer <u-boot@emk-elektronik.de>
cc: sshtylyov@mvista.com
The mpl-specfic memory test is only documented for one board, doesn't
compile cleanly, uses improper coding style, and overlaps functionality
with U-Boot's common 'mtest' command, so lets get rid of it.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: d.peter@mpl.ch
CC: d.mueller@elsoft.ch
CC: wd@denx.de
Previously the function was set_default_env(void), it is now
set_default_env(const char *s). This patch adds the required
parameter. This fixes a broken build on OMAP4430 SDP.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
The CCM board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix warning:
pm9g45.c: In function 'pm9g45_macb_hw_init':
pm9g45.c:99: warning: unused variable 'pio'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ilko Iliev <iliev@ronetix.at>
Fix warning:
pm9263.c: In function 'pm9263_macb_hw_init':
pm9263.c:99: warning: unused variable 'pio'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ilko Iliev <iliev@ronetix.at>
There are some cases where "make depend" would always run when
entering a directory. This happened when both the $(SRCS) and
$(HOSTSRCS) lists were empty (which is for example typical for the
examples/api/ directory). Avoid this by making sure that a ".depend"
file gets always created, even if empty.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Adds support for Winbond's W25Q64 SPI flash. These devices are used on
(among others) Xilinx' SP601 and SP605 Spartan-6 evaluation boards.
Tested with "sf" commands.
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPIO 16 and 19 reconfiguration should be done once USB is initialized.
So moved the reconfiguration to the USB init function.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the PPC4xx POST UART driver to use the common
NS16550 functions for receiving and sending. Additionally the
local function for SoC divisor setup are removed. Instead the
functions from arch/powerpc/cpu/ppc4xx/4xx_uart.c are used. This
removes code duplication.
Also the common CONFIG_SYS_NS16550_COMx defines are now used
to describe the POST UART's.
And a compile breakage is fixed, introduced by a git merge of
the ppc4xx/next branch into master. Now "ppc4xx.h" is moved to
"asm/ppc4xx.h". Fixed as well with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a bug in fdt_fixup_nor_flash_node() when the reg
property has multiple reg tuples, like:
reg = <0 0x00000000 0x04000000
0 0x04000000 0x04000000>;
In this case this function did not update the reg property correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch brings the lwmon5 board support up-to-date. Here a
summary of the changes:
lwmon5 board port related:
- GPIO's changed to control the LSB transmitter
- Reset USB PHY's upon power-up
- Enable CAN upon power-up
- USB init error workaround (errata CHIP_6)
- EBC: Enable burstmode and modify the timings for the GDC memory
- EBC: Speed up NOR flash timings
lwmon5 board POST related:
- Add FPGA memory test
- Add GDC memory test
- DSP POST reworked
- SYSMON POST: Fix handling of negative temperatures
- Add output for sysmon1 POST
- HW-watchdog min. time test reworked
Additionally some coding-style changes were done.
Signed-off-by: Sascha Laue <sascha.laue@liebherr.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support code for bluestone board wth APM821XX processor based.
This patch includes early board init, misc init, configure EBC,
initializes UIC, MAKEALL, board.cfg and MAINTAINERS file.
Signed-off-by: Tirumala R Marri <tmarri@apm.com
Signed-off-by: Stefan Roese <sr@denx.de>
APM821XX is a new line of SoCs which are derivatives of
PPC44X family of processors. This patch adds support of CPU, cache,
tlb, 32k ocm, bootstraps, PLB and AHB bus.
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The OTP code does a little shuffling of arguments that aren't really
necessary, so use a local variable instead to fix build errors now
that the args[] parameter is const.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Building this board for parallel flash fills up the bss section and thus
fails to link, so bump up the monitor size a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
