- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Enable the RNG on the Firefly, rock960 and RockPro64 devices
to enable KASLR on devices that support it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Akash Gajjar <akash@openedev.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Firefly RK3399 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This enables readning the cpuid from e-fuse, and deriving a static
MAC address from it.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.
After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Few SPL and U-Boot proper configs are common to all rk3399 target
defconfigs, move them and select it from platform kconfig.
Moved configs:
- SPL_ATF
- SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
- SPL_LOAD_FIT
- SPL_CLK if SPL
- SPL_PINCTRL if SPL
- SPL_RAM if SPL
- SPL_REGMAP if SPL
- SPL_SYSCON if SPL
- CLK
- FIT
- PINCTRL
- RAM
- REGMAP
- SYSCON
- DM_PMIC
- DM_REGULATOR_FIXED
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add default SPL_FIT_GENERATOR py script for rockchip platforms if
specific target enabled SPL_LOAD_FIT.
So, this would help get rid of explicitly mentioning the default
SPL FIT generator in defconfigs. however some targets, like puma_rk3399
still require their own FIT generator so in those cases the default will
override with defconfig defined generator.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The SPL is now running at SDRAM, and 0x10000 is used by BL31,
and the ARM SPL do not support relocate now, we need reserved
0x50000 so that it won't overwrite the code when we load the
bl31 to target space.
We should remove this after we enable the relocate feature.
The SPL need malloc 0x9000 for MMC as buffer used for transfer
data to IRAM(The EMMC DMA can not transfer data to IRAM directly).
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
If we used the pinctrl-rockchip driver, these config is not needed,
so remove them.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the fdtfile environment variable is set to
CONFIG_DEFAULT_DEVICE_TREE which is іnternally used as U-Boot devicetree
source. The OS can use a different filename and Kconfig gives us the
ability to select a default devicetree via CONFIG_DEFAULT_FDT_FILE.
This also gives user configuring U-Boot via menuconfig the behaviour
someone would expect.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have enable NS16550 in Kconfig, do not need enable at defconfig
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Rockchip-released ATF for the Firefly apparently (i.e. Kever
reported this) does not tolerate a FDT being passed as the platform
parameter and will run into a hard stop.
To work around this limitation in the ATF parameter handling, we
enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for
the platform parameters).
Note that this only affects this platform, as the ATF releases for the
RK3368 and RK3399 have always either ignored the platform parameter
(i.e. before the FDT-based parameters were supported) or support
receiving a pointer to a FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
